- 22 Jun, 2023 9 commits
-
-
Danielle Ratson authored
When mirroring to a gretap in hardware the device expects to be programmed with the egress port and all the encapsulating headers. This requires the driver to resolve the path the packet will take in the software data path and program the device accordingly. If the path cannot be resolved (in this case because of an unresolved neighbor), then mirror installation fails until the path is resolved. This results in a race that causes the test to sometimes fail. Fix this by setting the neighbor's state to permanent in a couple of tests, so that it is always valid. Fixes: 35c31d5c ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1d") Fixes: 239e754a ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1q") Signed-off-by:
Danielle Ratson <danieller@nvidia.com> Reviewed-by:
Petr Machata <petrm@nvidia.com> Signed-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Benjamin Berg authored
Properly check for RX_DROP_UNUSABLE now that the new drop reason infrastructure is used. Without this change, the comparison will always be false as a more specific reason is given in the lower bits of result. Fixes: baa951a1 ("mac80211: use the new drop reasons infrastructure") Signed-off-by:
Benjamin Berg <benjamin.berg@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Link: https://lore.kernel.org/r/20230621120543.412920-2-johannes@sipsolutions.netSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Matthieu Baerts says: ==================== mptcp: fixes for 6.4 Patch 1 correctly handles disconnect() failures that can happen in some specific cases: now the socket state is set as unconnected as expected. That fixes an issue introduced in v6.2. Patch 2 fixes a divide by zero bug in mptcp_recvmsg() with a fix similar to a recent one from Eric Dumazet for TCP introducing sk_wait_pending flag. It should address an issue present in MPTCP from almost the beginning, from v5.9. Patch 3 fixes a possible list corruption on passive MPJ even if the race seems very unlikely, better be safe than sorry. The possible issue is present from v5.17. Patch 4 consolidates fallback and non fallback state machines to avoid leaking some MPTCP sockets. The fix is likely needed for versions from v5.11. Patch 5 drops code that is no longer used after the introduction of patch 4/6. This is not really a fix but this patch can probably land in the -net tree as well not to leave unused code. Patch 6 ensures listeners are unhashed before updating their sk status to avoid possible deadlocks when diag info are going to be retrieved with a lock. Even if it should not be visible with the way we are currently getting diag info, the issue is present from v5.17. ==================== Link: https://lore.kernel.org/r/20230620-upstream-net-20230620-misc-fixes-for-v6-4-v1-0-f36aa5eae8b9@tessares.netSigned-off-by:
-
Paolo Abeni authored
The MPTCP protocol access the listener subflow in a lockless manner in a couple of places (poll, diag). That works only if the msk itself leaves the listener status only after that the subflow itself has been closed/disconnected. Otherwise we risk deadlock in diag, as reported by Christoph. Address the issue ensuring that the first subflow (the listener one) is always disconnected before updating the msk socket status. Reported-by:
Christoph Paasch <cpaasch@apple.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/407 Fixes: b29fcfb5 ("mptcp: full disconnect implementation") Cc: stable@vger.kernel.org Signed-off-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
-
Paolo Abeni authored
Thanks to the previous patch -- "mptcp: consolidate fallback and non fallback state machine" -- we can finally drop the "temporary hack" used to detect rx eof. Signed-off-by:
Mat Martineau <martineau@kernel.org> Signed-off-by:
-
Paolo Abeni authored
An orphaned msk releases the used resources via the worker, when the latter first see the msk in CLOSED status. If the msk status transitions to TCP_CLOSE in the release callback invoked by the worker's final release_sock(), such instance of the workqueue will not take any action. Additionally the MPTCP code prevents scheduling the worker once the socket reaches the CLOSE status: such msk resources will be leaked. The only code path that can trigger the above scenario is the __mptcp_check_send_data_fin() in fallback mode. Address the issue removing the special handling of fallback socket in __mptcp_check_send_data_fin(), consolidating the state machine for fallback and non fallback socket. Since non-fallback sockets do not send and do not receive data_fin, the mptcp code can update the msk internal status to match the next step in the SM every time data fin (ack) should be generated or received. As a consequence we can remove a bunch of checks for fallback from the fastpath. Fixes: 6e628cd3 ("mptcp: use mptcp release_cb for delayed tasks") Cc: stable@vger.kernel.org Signed-off-by:
-
Paolo Abeni authored
At passive MPJ time, if the msk socket lock is held by the user, the new subflow is appended to the msk->join_list under the msk data lock. In mptcp_release_cb()/__mptcp_flush_join_list(), the subflows in that list are moved from the join_list into the conn_list under the msk socket lock. Append and removal could race, possibly corrupting such list. Address the issue splicing the join list into a temporary one while still under the msk data lock. Found by code inspection, the race itself should be almost impossible to trigger in practice. Fixes: 3e501490 ("mptcp: cleanup MPJ subflow list handling") Cc: stable@vger.kernel.org Signed-off-by:
-
Paolo Abeni authored
Christoph reported a divide by zero bug in mptcp_recvmsg(): divide error: 0000 [#1] PREEMPT SMP CPU: 1 PID: 19978 Comm: syz-executor.6 Not tainted 6.4.0-rc2-gffcc7899081b #20 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014 RIP: 0010:__tcp_select_window+0x30e/0x420 net/ipv4/tcp_output.c:3018 Code: 11 ff 0f b7 cd c1 e9 0c b8 ff ff ff ff d3 e0 89 c1 f7 d1 01 cb 21 c3 eb 17 e8 2e 83 11 ff 31 db eb 0e e8 25 83 11 ff 89 d8 99 <f7> 7c 24 04 29 d3 65 48 8b 04 25 28 00 00 00 48 3b 44 24 10 75 60 RSP: 0018:ffffc90000a07a18 EFLAGS: 00010246 RAX: 000000000000ffd7 RBX: 000000000000ffd7 RCX: 0000000000040000 RDX: 0000000000000000 RSI: 000000000003ffff RDI: 0000000000040000 RBP: 000000000000ffd7 R08: ffffffff820cf297 R09: 0000000000000001 R10: 0000000000000000 R11: ffffffff8103d1a0 R12: 0000000000003f00 R13: 0000000000300000 R14: ffff888101cf3540 R15: 0000000000180000 FS: 00007f9af4c09640(0000) GS:ffff88813bd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b33824000 CR3: 000000012f241001 CR4: 0000000000170ee0 Call Trace: <TASK> __tcp_cleanup_rbuf+0x138/0x1d0 net/ipv4/tcp.c:1611 mptcp_recvmsg+0xcb8/0xdd0 net/mptcp/protocol.c:2034 inet_recvmsg+0x127/0x1f0 net/ipv4/af_inet.c:861 ____sys_recvmsg+0x269/0x2b0 net/socket.c:1019 ___sys_recvmsg+0xe6/0x260 net/socket.c:2764 do_recvmmsg+0x1a5/0x470 net/socket.c:2858 __do_sys_recvmmsg net/socket.c:2937 [inline] __se_sys_recvmmsg net/socket.c:2953 [inline] __x64_sys_recvmmsg+0xa6/0x130 net/socket.c:2953 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x47/0xa0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7f9af58fc6a9 Code: 5c c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 4f 37 0d 00 f7 d8 64 89 01 48 RSP: 002b:00007f9af4c08cd8 EFLAGS: 00000246 ORIG_RAX: 000000000000012b RAX: ffffffffffffffda RBX: 00000000006bc050 RCX: 00007f9af58fc6a9 RDX: 0000000000000001 RSI: 0000000020000140 RDI: 0000000000000004 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000f00 R11: 0000000000000246 R12: 00000000006bc05c R13: fffffffffffffea8 R14: 00000000006bc050 R15: 000000000001fe40 </TASK> mptcp_recvmsg is allowed to release the msk socket lock when blocking, and before re-acquiring it another thread could have switched the sock to TCP_LISTEN status - with a prior connect(AF_UNSPEC) - also clearing icsk_ack.rcv_mss. Address the issue preventing the disconnect if some other process is concurrently performing a blocking syscall on the same socket, alike commit 4faeee0c ("tcp: deny tcp_disconnect() when threads are waiting"). Fixes: a6b118fe ("mptcp: add receive buffer auto-tuning") Cc: stable@vger.kernel.org Reported-by:
-
Paolo Abeni authored
Currently the mptcp code has assumes that disconnect() can fail only at mptcp_sendmsg_fastopen() time - to avoid a deadlock scenario - and don't even bother returning an error code. Soon mptcp_disconnect() will handle more error conditions: let's track them explicitly. As a bonus, explicitly annotate TCP-level disconnect as not failing: the mptcp code never blocks for event on the subflows. Fixes: 7d803344 ("mptcp: fix deadlock in fastopen error path") Cc: stable@vger.kernel.org Signed-off-by:
-
- 21 Jun, 2023 5 commits
-
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski authored
Daniel Borkmann says: ==================== pull-request: bpf 2023-06-21 We've added 7 non-merge commits during the last 14 day(s) which contain a total of 7 files changed, 181 insertions(+), 15 deletions(-). The main changes are: 1) Fix a verifier id tracking issue with scalars upon spill, from Maxim Mikityanskiy. 2) Fix NULL dereference if an exception is generated while a BPF subprogram is running, from Krister Johansen. 3) Fix a BTF verification failure when compiling kernel with LLVM_IAS=0, from Florent Revest. 4) Fix expected_attach_type enforcement for kprobe_multi link, from Jiri Olsa. 5) Fix a bpf_jit_dump issue for x86_64 to pick the correct JITed image, from Yonghong Song. * tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf: bpf: Force kprobe multi expected_attach_type for kprobe_multi link bpf/btf: Accept function names that contain dots selftests/bpf: add a test for subprogram extables bpf: ensure main program has an extable bpf: Fix a bpf_jit_dump issue for x86_64 with sysctl bpf_jit_enable. selftests/bpf: Add test cases to assert proper ID tracking on spill bpf: Fix verifier id tracking of scalars on spill ==================== Link: https://lore.kernel.org/r/20230621101116.16122-1-daniel@iogearbox.netSigned-off-by:
-
Jiri Olsa authored
We currently allow to create perf link for program with expected_attach_type == BPF_TRACE_KPROBE_MULTI. This will cause crash when we call helpers like get_attach_cookie or get_func_ip in such program, because it will call the kprobe_multi's version (current->bpf_ctx context setup) of those helpers while it expects perf_link's current->bpf_ctx context setup. Making sure that we use BPF_TRACE_KPROBE_MULTI expected_attach_type only for programs attaching through kprobe_multi link. Fixes: ca74823c ("bpf: Add cookie support to programs attached with kprobe multi link") Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Signed-off-by:
Andrii Nakryiko <andrii@kernel.org> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20230618131414.75649-1-jolsa@kernel.org
-
Florent Revest authored
When building a kernel with LLVM=1, LLVM_IAS=0 and CONFIG_KASAN=y, LLVM leaves DWARF tags for the "asan.module_ctor" & co symbols. In turn, pahole creates BTF_KIND_FUNC entries for these and this makes the BTF metadata validation fail because they contain a dot. In a dramatic turn of event, this BTF verification failure can cause the netfilter_bpf initialization to fail, causing netfilter_core to free the netfilter_helper hashmap and netfilter_ftp to trigger a use-after-free. The risk of u-a-f in netfilter will be addressed separately but the existence of "asan.module_ctor" debug info under some build conditions sounds like a good enough reason to accept functions that contain dots in BTF. Although using only LLVM=1 is the recommended way to compile clang-based kernels, users can certainly do LLVM=1, LLVM_IAS=0 as well and we still try to support that combination according to Nick. To clarify: - > v5.10 kernel, LLVM=1 (LLVM_IAS=0 is not the default) is recommended, but user can still have LLVM=1, LLVM_IAS=0 to trigger the issue - <= 5.10 kernel, LLVM=1 (LLVM_IAS=0 is the default) is recommended in which case GNU as will be used Fixes: 1dc92851 ("bpf: kernel side support for BTF Var and DataSec") Signed-off-by:Florent Revest <revest@chromium.org> Signed-off-by:
-
Francesco Dolcini authored
This reverts commit da9ef50f. This fixes a regression in which the link would come up, but no communication was possible. The reverted commit was also removing a comment about DP83867_PHYCR_FORCE_LINK_GOOD, this is not added back in this commits since it seems that this is unrelated to the original code change. Closes: https://lore.kernel.org/all/ZGuDJos8D7N0J6Z2@francesco-nb.int.toradex.com/ Fixes: da9ef50f ("net: phy: dp83867: perform soft reset and retain established link") Signed-off-by:
Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Praneeth Bajjuri <praneeth@ti.com> Link: https://lore.kernel.org/r/20230619154435.355485-1-francesco@dolcini.itSigned-off-by:
-
Jiawen Wu authored
PHY address and device address are passed in the wrong order. Cc: stable@vger.kernel.org Fixes: 4e4aafcd ("net: mdio: Add dedicated C45 API to MDIO bus drivers") Signed-off-by:
Jiawen Wu <jiawenwu@trustnetic.com> Reviewed-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20230619094948.84452-1-jiawenwu@trustnetic.comSigned-off-by:
-
- 20 Jun, 2023 12 commits
-
-
Mukesh Sisodiya authored
Add support for AX1690i and AX1690s devices with PCIE id 0x7AF0. Cc: stable@vger.kernel.org # 6.1+ Signed-off-by:
Mukesh Sisodiya <mukesh.sisodiya@intel.com> Signed-off-by:
Gregory Greenman <gregory.greenman@intel.com> Signed-off-by:
-
Ross Lagerwall authored
We have seen a bug where the NIC incorrectly changes the length in the IP header of a padded packet to include the padding bytes. The driver already has a workaround for this so do the workaround for this NIC too. This resolves the issue. The NIC in question identifies itself as follows: [ 8.828494] be2net 0000:02:00.0: FW version is 10.7.110.31 [ 8.834759] be2net 0000:02:00.0: Emulex OneConnect(be3): PF FLEX10 port 1 02:00.0 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 01) Fixes: ca34fe38 ("be2net: fix wrong usage of adapter->generation") Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Link: https://lore.kernel.org/r/20230616164549.2863037-1-ross.lagerwall@citrix.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsecDavid S. Miller authored
ipsec-2023-06-20
-
David S. Miller authored
Arınç ÜNAL says: ==================== net: dsa: mt7530: fix multiple CPU ports, BPDU and LLDP handling This patch series fixes all non-theoretical issues regarding multiple CPU ports and the handling of LLDP frames and BPDUs. I am adding me as a maintainer, I've got some code improvements on the way. I will keep an eye on this driver and the patches submitted for it in the future. Arınç v6: - Change a small portion of the comment in the diff on "net: dsa: mt7530: set all CPU ports in MT7531_CPU_PMAP" with Russell's suggestion. - Change the patch log of "net: dsa: mt7530: fix trapping frames on non-MT7621 SoC MT7530 switch" with Vladimir's suggestion. - Group the code for trapping frames into a common function and call that. - Add Vladimir and Russell's reviewed-by tags to where they're given. v5: - Change the comment in the diff on the first patch with Russell's words. - Change the patch log of the first patch to state that the patch is just preparatory work for change "net: dsa: introduce preferred_default_local_cpu_port and use on MT7530" and not a fix to an existing problem on the code base. - Remove the "net: dsa: mt7530: fix trapping frames with multiple CPU ports on MT7530" patch. It fixes a theoretical issue, therefore it is net-next material. - Remove unnecessary information from the patch logs. Remove the enum renaming change. - Strengthen the point of the "net: dsa: introduce preferred_default_local_cpu_port and use on MT7530" patch. v4: Make the patch logs and my comments in the code easier to understand. v3: Fix the from header on the patches. Write a cover letter. v2: Add patches to fix the handling of LLDP frames and BPDUs. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Arınç ÜNAL authored
Add me as a maintainer of the MediaTek MT7530 DSA subdriver. List maintainers in alphabetical order by first name. Signed-off-by:
Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
Matthias Brugger <matthias.bgg@gmail.com> Reviewed-by:
Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by:
-
Vladimir Oltean authored
Since the introduction of the OF bindings, DSA has always had a policy that in case multiple CPU ports are present in the device tree, the numerically smallest one is always chosen. The MT7530 switch family, except the switch on the MT7988 SoC, has 2 CPU ports, 5 and 6, where port 6 is preferable on the MT7531BE switch because it has higher bandwidth. The MT7530 driver developers had 3 options: - to modify DSA when the MT7531 switch support was introduced, such as to prefer the better port - to declare both CPU ports in device trees as CPU ports, and live with the sub-optimal performance resulting from not preferring the better port - to declare just port 6 in the device tree as a CPU port Of course they chose the path of least resistance (3rd option), kicking the can down the road. The hardware description in the device tree is supposed to be stable - developers are not supposed to adopt the strategy of piecemeal hardware description, where the device tree is updated in lockstep with the features that the kernel currently supports. Now, as a result of the fact that they did that, any attempts to modify the device tree and describe both CPU ports as CPU ports would make DSA change its default selection from port 6 to 5, effectively resulting in a performance degradation visible to users with the MT7531BE switch as can be seen below. Without preferring port 6: [ ID][Role] Interval Transfer Bitrate Retr [ 5][TX-C] 0.00-20.00 sec 374 MBytes 157 Mbits/sec 734 sender [ 5][TX-C] 0.00-20.00 sec 373 MBytes 156 Mbits/sec receiver [ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 778 Mbits/sec 0 sender [ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 777 Mbits/sec receiver With preferring port 6: [ ID][Role] Interval Transfer Bitrate Retr [ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 856 Mbits/sec 273 sender [ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 855 Mbits/sec receiver [ 7][RX-C] 0.00-20.00 sec 1.72 GBytes 737 Mbits/sec 15 sender [ 7][RX-C] 0.00-20.00 sec 1.71 GBytes 736 Mbits/sec receiver Using one port for WAN and the other ports for LAN is a very popular use case which is what this test emulates. As such, this change proposes that we retroactively modify stable kernels (which don't support the modification of the CPU port assignments, so as to let user space fix the problem and restore the throughput) to keep the mt7530 driver preferring port 6 even with device trees where the hardware is more fully described. Fixes: c288575f ("net: dsa: mt7530: Add the support of MT7531 switch") Signed-off-by:
-
Arınç ÜNAL authored
LLDP frames are link-local frames, therefore they must be trapped to the CPU port. Currently, the MT753X switches treat LLDP frames as regular multicast frames, therefore flooding them to user ports. To fix this, set LLDP frames to be trapped to the CPU port(s). Fixes: b8f126a8 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by:
-
Arınç ÜNAL authored
BPDUs are link-local frames, therefore they must be trapped to the CPU port. Currently, the MT7530 switch treats BPDUs as regular multicast frames, therefore flooding them to user ports. To fix this, set BPDUs to be trapped to the CPU port. Group this on mt7530_setup() and mt7531_setup_common() into mt753x_trap_frames() and call that. Fixes: b8f126a8 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by:
-
Arınç ÜNAL authored
All MT7530 switch IP variants share the MT7530_MFC register, but the current driver only writes it for the switch variant that is integrated in the MT7621 SoC. Modify the code to include all MT7530 derivatives. Fixes: b8f126a8 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Suggested-by:
-
Arınç ÜNAL authored
MT7531_CPU_PMAP represents the destination port mask for trapped-to-CPU frames (further restricted by PCR_MATRIX). Currently the driver sets the first CPU port as the single port in this bit mask, which works fine regardless of whether the device tree defines port 5, 6 or 5+6 as CPU ports. This is because the logic coincides with DSA's logic of picking the first CPU port as the CPU port that all user ports are affine to, by default. An upcoming change would like to influence DSA's selection of the default CPU port to no longer be the first one, and in that case, this logic needs adaptation. Since there is no observed leakage or duplication of frames if all CPU ports are defined in this bit mask, simply include them all. Suggested-by:
Russell King (Oracle) <linux@armlinux.org.uk> Suggested-by:
-
Josua Mayer authored
Layerscape MACs support 25Gbps network speed with dpmac "CAUI" mode. Add the mappings between DPMAC_ETH_IF_* and HY_INTERFACE_MODE_*, as well as the 25000 mac capability. Tested on SolidRun LX2162a Clearfog, serdes 1 protocol 18. Signed-off-by:
Josua Mayer <josua@solid-run.com> Reviewed-by:
-
David S. Miller authored
Merge tag 'ieee802154-for-net-2023-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan Stefan Schmidt says: ==================== An update from ieee802154 for your *net* tree: Two small fixes and MAINTAINERS update this time. Azeem Shaikh ensured consistent use of strscpy through the tree and fixed the usage in our trace.h. Chen Aotian fixed a potential memory leak in the hwsim simulator for ieee802154. Miquel Raynal updated the MAINATINERS file with the new team git tree locations and patchwork URLs. ==================== Signed-off-by:
-
- 19 Jun, 2023 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-fixes-2023-06-16 This series provides bug fixes to mlx5 driver. Please pull and let me know if there is any problem. ==================== Signed-off-by: -
Stefan Wahren authored
In case the QCA7000 is not available via SPI (e.g. in reset), the driver will cause a high load. The reason for this is that the synchronization is never finished and schedule() is never called. Since the synchronization is not timing critical, it's safe to drop this from the scheduling condition. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06e ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by:
-
- 18 Jun, 2023 3 commits
-
-
Andrew Lunn authored
If the core is left to remove the LEDs via devm_, it is performed too late, after the PHY driver is removed from the PHY. This results in dereferencing a NULL pointer when the LED core tries to turn the LED off before destroying the LED. Manually unregister the LEDs at a safe point in phy_remove. Cc: stable@vger.kernel.org Reported-by:
Florian Fainelli <f.fainelli@gmail.com> Suggested-by:
-
Juerg Haefliger authored
The module loads firmware so add MODULE_FIRMWARE macros to provide that information via modinfo. Signed-off-by:
Juerg Haefliger <juerg.haefliger@canonical.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Juerg Haefliger authored
The module loads firmware so add a MODULE_FIRMWARE macro to provide that information via modinfo. Signed-off-by:
-
- 17 Jun, 2023 1 commit
-
-
Íñigo Huguet authored
When running workloads heavy unbalanced towards TX (high TX, low RX traffic), sfc driver can retain the CPU during too long times. Although in many cases this is not enough to be visible, it can affect performance and system responsiveness. A way to reproduce it is to use a debug kernel and run some parallel netperf TX tests. In some systems, this will lead to this message being logged: kernel:watchdog: BUG: soft lockup - CPU#12 stuck for 22s! The reason is that sfc driver doesn't account any NAPI budget for the TX completion events work. With high-TX/low-RX traffic, this makes that the CPU is held for long time for NAPI poll. Documentations says "drivers can process completions for any number of Tx packets but should only process up to budget number of Rx packets". However, many drivers do limit the amount of TX completions that they process in a single NAPI poll. In the same way, this patch adds a limit for the TX work in sfc. With the patch applied, the watchdog warning never appears. Tested with netperf in different combinations: single process / parallel processes, TCP / UDP and different sizes of UDP messages. Repeated the tests before and after the patch, without any noticeable difference in network or CPU performance. Test hardware: Intel(R) Xeon(R) CPU E5-1620 v4 @ 3.50GHz (4 cores, 2 threads/core) Solarflare Communications XtremeScale X2522-25G Network Adapter Fixes: 5227eccc ("sfc: remove tx and MCDI handling from NAPI budget consideration") Fixes: d19a5372 ("sfc_ef100: TX path for EF100 NICs") Reported-by:
Fei Liu <feliu@redhat.com> Signed-off-by:
Íñigo Huguet <ihuguet@redhat.com> Acked-by:
Martin Habets <habetsm.xilinx@gmail.com> Link: https://lore.kernel.org/r/20230615084929.10506-1-ihuguet@redhat.comSigned-off-by:
-
- 16 Jun, 2023 8 commits
-
-
Azeem Shaikh authored
strlcpy() reads the entire source buffer first. This read may exceed the destination size limit. This is both inefficient and can lead to linear read overflows if a source string is not NUL-terminated [1]. In an effort to remove strlcpy() completely [2], replace strlcpy() here with strscpy(). Direct replacement is safe here since the return values from the helper macros are ignored by the callers. [1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy [2] https://github.com/KSPP/linux/issues/89Signed-off-by:
Azeem Shaikh <azeemshaikh38@gmail.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230613003326.3538391-1-azeemshaikh38@gmail.comSigned-off-by:
Stefan Schmidt <stefan@datenfreihafen.org>
-
Leon Romanovsky authored
ASO query can be scheduled in atomic context as such it can't use usleep. Use udelay as recommended in Documentation/timers/timers-howto.rst. Fixes: 76e463f6 ("net/mlx5e: Overcome slow response for first IPsec ASO WQE") Signed-off-by:
Leon Romanovsky <leonro@nvidia.com> Reviewed-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Leon Romanovsky authored
XFRM state which is changed to be XFRM_STATE_EXPIRED doesn't really need to hold lock while modifying flow steering rules to drop traffic. That state can be deleted only and as such mlx5e_ipsec_handle_tx_limit() work will be canceled anyway and won't run in parallel. Fixes: b2f7b01d ("net/mlx5e: Simulate missing IPsec TX limits hardware functionality") Signed-off-by:
-
Patrisious Haddad authored
Previously during mlx5e_ipsec_handle_event the driver tried to execute an operation that could sleep, while holding a spinlock, which caused the kernel panic mentioned below. Move the function call that can sleep outside of the spinlock context. Call Trace: <TASK> dump_stack_lvl+0x49/0x6c __schedule_bug.cold+0x42/0x4e schedule_debug.constprop.0+0xe0/0x118 __schedule+0x59/0x58a ? __mod_timer+0x2a1/0x3ef schedule+0x5e/0xd4 schedule_timeout+0x99/0x164 ? __pfx_process_timeout+0x10/0x10 __wait_for_common+0x90/0x1da ? __pfx_schedule_timeout+0x10/0x10 wait_func+0x34/0x142 [mlx5_core] mlx5_cmd_invoke+0x1f3/0x313 [mlx5_core] cmd_exec+0x1fe/0x325 [mlx5_core] mlx5_cmd_do+0x22/0x50 [mlx5_core] mlx5_cmd_exec+0x1c/0x40 [mlx5_core] mlx5_modify_ipsec_obj+0xb2/0x17f [mlx5_core] mlx5e_ipsec_update_esn_state+0x69/0xf0 [mlx5_core] ? wake_affine+0x62/0x1f8 mlx5e_ipsec_handle_event+0xb1/0xc0 [mlx5_core] process_one_work+0x1e2/0x3e6 ? __pfx_worker_thread+0x10/0x10 worker_thread+0x54/0x3ad ? __pfx_worker_thread+0x10/0x10 kthread+0xda/0x101 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x29/0x37 </TASK> BUG: workqueue leaked lock or atomic: kworker/u256:4/0x7fffffff/189754#012 last function: mlx5e_ipsec_handle_event [mlx5_core] CPU: 66 PID: 189754 Comm: kworker/u256:4 Kdump: loaded Tainted: G W 6.2.0-2596.20230309201517_5.el8uek.rc1.x86_64 #2 Hardware name: Oracle Corporation ORACLE SERVER X9-2/ASMMBX9-2, BIOS 61070300 08/17/2022 Workqueue: mlx5e_ipsec: eth%d mlx5e_ipsec_handle_event [mlx5_core] Call Trace: <TASK> dump_stack_lvl+0x49/0x6c process_one_work.cold+0x2b/0x3c ? __pfx_worker_thread+0x10/0x10 worker_thread+0x54/0x3ad ? __pfx_worker_thread+0x10/0x10 kthread+0xda/0x101 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x29/0x37 </TASK> BUG: scheduling while atomic: kworker/u256:4/189754/0x00000000 Fixes: cee137a6 ("net/mlx5e: Handle ESN update events") Signed-off-by:
Patrisious Haddad <phaddad@nvidia.com> Signed-off-by:
-
Leon Romanovsky authored
XFRM core provides two callbacks to release resources, one is .xdo_dev_policy_delete() and another is .xdo_dev_policy_free(). This separation allows delayed release so "ip xfrm policy free" commands won't starve. Unfortunately, mlx5 command interface can't run in .xdo_dev_policy_free() callbacks as the latter runs in ATOMIC context. BUG: scheduling while atomic: swapper/7/0/0x00000100 Modules linked in: act_mirred act_tunnel_key cls_flower sch_ingress vxlan mlx5_vdpa vringh vhost_iotlb vdpa rpcrdma rdma_ucm ib_iser libiscsi ib_umad scsi_transport_iscsi rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay mlx5_core zram zsmalloc fuse CPU: 7 PID: 0 Comm: swapper/7 Not tainted 6.3.0+ #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <IRQ> dump_stack_lvl+0x33/0x50 __schedule_bug+0x4e/0x60 __schedule+0x5d5/0x780 ? __mod_timer+0x286/0x3d0 schedule+0x50/0x90 schedule_timeout+0x7c/0xf0 ? __bpf_trace_tick_stop+0x10/0x10 __wait_for_common+0x88/0x190 ? usleep_range_state+0x90/0x90 cmd_exec+0x42e/0xb40 [mlx5_core] mlx5_cmd_do+0x1e/0x40 [mlx5_core] mlx5_cmd_exec+0x18/0x30 [mlx5_core] mlx5_cmd_delete_fte+0xa8/0xd0 [mlx5_core] del_hw_fte+0x60/0x120 [mlx5_core] mlx5_del_flow_rules+0xec/0x270 [mlx5_core] ? default_send_IPI_single_phys+0x26/0x30 mlx5e_accel_ipsec_fs_del_pol+0x1a/0x60 [mlx5_core] mlx5e_xfrm_free_policy+0x15/0x20 [mlx5_core] xfrm_policy_destroy+0x5a/0xb0 xfrm4_dst_destroy+0x7b/0x100 dst_destroy+0x37/0x120 rcu_core+0x2d6/0x540 __do_softirq+0xcd/0x273 irq_exit_rcu+0x82/0xb0 sysvec_apic_timer_interrupt+0x72/0x90 </IRQ> <TASK> asm_sysvec_apic_timer_interrupt+0x16/0x20 RIP: 0010:default_idle+0x13/0x20 Code: c0 08 00 00 00 4d 29 c8 4c 01 c7 4c 29 c2 e9 72 ff ff ff cc cc cc cc 8b 05 7a 4d ee 00 85 c0 7e 07 0f 00 2d 2f 98 2e 00 fb f4 <fa> c3 66 66 2e 0f 1f 84 00 00 00 00 00 65 48 8b 04 25 40 b4 02 00 RSP: 0018:ffff888100843ee0 EFLAGS: 00000242 RAX: 0000000000000001 RBX: ffff888100812b00 RCX: 4000000000000000 RDX: 0000000000000001 RSI: 0000000000000083 RDI: 000000000002d2ec RBP: 0000000000000007 R08: 00000021daeded59 R09: 0000000000000001 R10: 0000000000000000 R11: 000000000000000f R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 default_idle_call+0x30/0xb0 do_idle+0x1c1/0x1d0 cpu_startup_entry+0x19/0x20 start_secondary+0xfe/0x120 secondary_startup_64_no_verify+0xf3/0xfb </TASK> bad: scheduling from the idle thread! Fixes: a5b8ca94 ("net/mlx5e: Add XFRM policy offload logic") Signed-off-by:
-
Saeed Mahameed authored
The kernel IRQ system needs the irq affinity notifier to be clear before attempting to free the irq, see WARN_ON log below. On a normal driver unload we don't have this issue since we do the complete cleanup of the irq resources. To fix this, put the important resources cleanup in a helper function and use it in both normal driver unload and shutdown flows. [ 4497.498434] ------------[ cut here ]------------ [ 4497.498726] WARNING: CPU: 0 PID: 9 at kernel/irq/manage.c:2034 free_irq+0x295/0x340 [ 4497.499193] Modules linked in: [ 4497.499386] CPU: 0 PID: 9 Comm: kworker/0:1 Tainted: G W 6.4.0-rc4+ #10 [ 4497.499876] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc38 04/01/2014 [ 4497.500518] Workqueue: events do_poweroff [ 4497.500849] RIP: 0010:free_irq+0x295/0x340 [ 4497.501132] Code: 85 c0 0f 84 1d ff ff ff 48 89 ef ff d0 0f 1f 00 e9 10 ff ff ff 0f 0b e9 72 ff ff ff 49 8d 7f 28 ff d0 0f 1f 00 e9 df fd ff ff <0f> 0b 48 c7 80 c0 008 [ 4497.502269] RSP: 0018:ffffc90000053da0 EFLAGS: 00010282 [ 4497.502589] RAX: ffff888100949600 RBX: ffff88810330b948 RCX: 0000000000000000 [ 4497.503035] RDX: ffff888100949600 RSI: ffff888100400490 RDI: 0000000000000023 [ 4497.503472] RBP: ffff88810330c7e0 R08: ffff8881004005d0 R09: ffffffff8273a260 [ 4497.503923] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8881009ae000 [ 4497.504359] R13: ffff8881009ae148 R14: 0000000000000000 R15: ffff888100949600 [ 4497.504804] FS: 0000000000000000(0000) GS:ffff88813bc00000(0000) knlGS:0000000000000000 [ 4497.505302] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 4497.505671] CR2: 00007fce98806298 CR3: 000000000262e005 CR4: 0000000000370ef0 [ 4497.506104] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 4497.506540] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 4497.507002] Call Trace: [ 4497.507158] <TASK> [ 4497.507299] ? free_irq+0x295/0x340 [ 4497.507522] ? __warn+0x7c/0x130 [ 4497.507740] ? free_irq+0x295/0x340 [ 4497.507963] ? report_bug+0x171/0x1a0 [ 4497.508197] ? handle_bug+0x3c/0x70 [ 4497.508417] ? exc_invalid_op+0x17/0x70 [ 4497.508662] ? asm_exc_invalid_op+0x1a/0x20 [ 4497.508926] ? free_irq+0x295/0x340 [ 4497.509146] mlx5_irq_pool_free_irqs+0x48/0x90 [ 4497.509421] mlx5_irq_table_free_irqs+0x38/0x50 [ 4497.509714] mlx5_core_eq_free_irqs+0x27/0x40 [ 4497.509984] shutdown+0x7b/0x100 [ 4497.510184] pci_device_shutdown+0x30/0x60 [ 4497.510440] device_shutdown+0x14d/0x240 [ 4497.510698] kernel_power_off+0x30/0x70 [ 4497.510938] process_one_work+0x1e6/0x3e0 [ 4497.511183] worker_thread+0x49/0x3b0 [ 4497.511407] ? __pfx_worker_thread+0x10/0x10 [ 4497.511679] kthread+0xe0/0x110 [ 4497.511879] ? __pfx_kthread+0x10/0x10 [ 4497.512114] ret_from_fork+0x29/0x50 [ 4497.512342] </TASK> Fixes: 9c2d0801 ("net/mlx5: Free irqs only on shutdown callback") Signed-off-by:
Shay Drory <shayd@nvidia.com>
-
Yevgeny Kliteynik authored
When TUNNEL_L3_TO_L2 decap action was created, a pointer to a local variable was passed as its HW action data, resulting in attempt to free invalid address: BUG: KASAN: invalid-free in mlx5dr_action_destroy+0x318/0x410 [mlx5_core] Fixes: 4781df92 ("net/mlx5: DR, Move STEv0 modify header logic") Signed-off-by:
Yevgeny Kliteynik <kliteyn@nvidia.com> Reviewed-by:
Alex Vesker <valex@nvidia.com> Signed-off-by:
-
Yevgeny Kliteynik authored
In some cases, steering might need to use SW-created action in FW table, which results in wrong packet reformat being used: mlx5_core 0000:81:00.1: mlx5_cmd_check:756:(pid 1154): SET_FLOW_TABLE_ENTRY(0×936) op_mod(0×0) failed, status bad resource(0×5), syndrome (0xf2ff71) This patch adds support for usage of SW-created packet reformat (encap) actions in FW tables, and adds clear error flow for attempt to use SW-created modify header on FW tables. Fixes: 6a48faee ("net/mlx5: Add direct rule fs_cmd implementation") Signed-off-by:Erez Shitrit <erezsh@nvidia.com> Signed-off-by:
-
