- 29 May, 2012 5 commits
-
-
Emil Goode authored
This patch fixes the cleanup code of the bfin_adv7393_fb_probe function. 1) The resources were not freed in the order that we allocated them so we call dma_free_coherent() before it was allocated. 2) The labels weren't in the right place which also meant that we freed resources that weren't allocated. 3) We should free gpio_free(P_IDENT(P_PPI0_FS3)) before returning. 4) Lets change the label names into something more meaningful. Signed-off-by:
Emil Goode <emilgoode@gmail.com> Acked-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
-
Jingoo Han authored
This patch reduces delay time when configuring video setting, which is helpful to reduce wakeup time during resume. Signed-off-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
-
Jingoo Han authored
The sw reset should be called prioir to enabling sw defined function, according to datasheet. Signed-off-by:
-
Jingoo Han authored
The devm_ functions allocate memory that is released when a driver detaches. This makes the code smaller and a bit simpler. Signed-off-by:
-
Dan Carpenter authored
This function is called with a potential NULL pointer in picolcd_init_framebuffer() and it causes a static checker warning. This used to handle NULL pointers when the picolcd code was written, but a couple months later we added the "info->apertures" dereference. Signed-off-by:
Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by:
-
- 27 May, 2012 1 commit
-
-
git://github.com/tomba/linuxFlorian Tobias Schandinat authored
Omapdss driver changes for 3.5 merge window. Lots of normal development commits, but perhaps most notable changes are: * HDMI rework to properly decouple the HDMI audio part from the HDMI video part. * Restructure omapdss core driver so that it's possible to implement device tree support. This included changing how platform data is passed to the drivers, changing display device registration and improving the panel driver's ability to configure the underlying video output interface. * Basic support for DSI packet interleaving
-
- 22 May, 2012 9 commits
-
-
Ricardo Neri authored
genirq requires that the IRQ requests that do not provided a handler to use the IRQF_ONESHOT flag. This is to prevent situations in which the irq line is reenabled while the interrupt is still asserted. While this situation may not happen in edge type interrupts, genirq still requires to use IRQF_ONESHOT. Also, remove the IRQF_DISABLED as the flag is now a NOOP and has been deprecated. Signed-off-by:
Ricardo Neri <ricardo.neri@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com>
-
Archit Taneja authored
The VENC interfaces uses it's venc_set_timing() function to take in a new set of timings. If the panel is disabled, it does not disable and re-enable the interface. Currently, the manager timings are applied in venc_power_on(), these are not called by set_timings if the panel is disabled. When checking overlay and manager data, the DSS driver uses the last applied manager timings, and not the timings held by omap_dss_device struct. Hence, there is a need to apply the new manager timings even if the panel is disabled. Apply the manager timings if the VENC panel is disabled. This is similar to the commit below which fixed the same issue for HDMI/DPI interfaces: fcc36619Signed-off-by:
Archit Taneja <archit@ti.com> Signed-off-by:
-
Archit Taneja authored
DSS2 driver uses the timings in manager's private data to check the validity of overlay and manager infos written by the user. For VENC interface, we divide the Y resolution by half when writing to the DISPC_DIGIT_SIZE register as the content is interlaced. However, the height of the manager/display with respect to the content shown through VENC still remains the same. The VENC driver divides the y_res parameter in omap_video_timings by half, and then applies the configuration. This leads to manager's private data storing the wrong Y resolution. Hence, overlay related checks fail. Ensure that manager's private data stores the original timings, and the Y resolution is halved only when we write to the DISPC register. This is a hack, the proper solution would be to pass some sort of interlace parameter which makes the call whether we should divide y_res or not. Signed-off-by:
-
Chandrabhanu Mahapatra authored
TILER is a block in OMAP4's DMM which lets DSS fetch frames in a rotated manner. Physical memory can be mapped to a portion of OMAP's system address space called TILER address space. The TILER address space is split into 8 views. Each view represents a rotated or mirrored form of the mapped physical memory. When a DISPC overlay's base address is programmed to one of these views, the TILER fetches the pixels according to the orientation of the view. A view is further split into 4 containers, each container holds elements of a particular size. Rotation can be achieved at the granularity of elements in the container. For more information on TILER, refer to the Memory Subsytem section in OMAP4 TRM. Rotation type TILER has been added which is used to exploit the capabilities of these 8 views for performing various rotations. When fetching from addresses mapped to TILER space, the DISPC DMA can fetch pixels in either 1D or 2D bursts. The fetch depends on which TILER container we are accessing. Accessing 8, 16 and 32 bit sized containers requires 2D bursts, and page mode sized containers require 1D bursts. The DSS2 user is expected to provide the Tiler address of the view that it is interested in. This is passed to the paddr and p_uv_addr parameters in omap_overlay_info. It is also expected to provide the stride value based on the view's orientation and container type, this should be passed to the screen_width parameter of omap_overlay_info. In calc_tiler_rotation_offset screen_width is used to calculate the required row_inc for DISPC. x_predecim and y_predecim are also used to calculate row_inc and pix_inc thereby adding predecimation support for TILER. Signed-off-by:
Chandrabhanu Mahapatra <cmahapatra@ti.com> Signed-off-by:
-
Tomi Valkeinen authored
If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many places in code expect the execution to stop, and this causes compiler warnings about uninitialized variables and returning from a non-void function without a return value. This patch fixes the warnings by initializing the variables and returning properly after BUG() lines. However, the behaviour is still undefined after the BUG, but this is the choice the user makes when using CONFIG_BUG=n. Signed-off-by: -
Tomi Valkeinen authored
If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many places in code expect the execution to stop, and this causes compiler warnings about uninitialized variables and returning from a non-void function without a return value. This patch fixes the warnings by initializing the variables and returning properly after BUG() lines. However, the behaviour is still undefined after the BUG, but this is the choice the user makes when using CONFIG_BUG=n. Signed-off-by: -
Tomi Valkeinen authored
If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many places in code expect the execution to stop, and this causes compiler warnings about uninitialized variables and returning from a non-void function without a return value. This patch fixes the warnings by initializing the variables and returning properly after BUG() lines. However, the behaviour is still undefined after the BUG, but this is the choice the user makes when using CONFIG_BUG=n. Signed-off-by: -
Tomi Valkeinen authored
Commit 05dd0f53 ("OMAPDSS: DISPC: Update Accumulator configuration for chroma plane") adds dispc_ovl_set_accu_uv() function that sets the accu, but the function only handles YUV and NV12 modes, and BUGs otherwise. The patch also adds a call to the function, but unfortunately the place of call was such that the mode could be other than YUV or NV12, thus crashing the driver. This patchs moves the call to a slightly later spot, at which point only YUV and NV12 modes are handled. Signed-off-by:
-
Tomi Valkeinen authored
There is a problem related to DSS FIFO thresholds and power management on OMAP3. It seems that when the full PM hits in, we get underflows. The core reason is unknown, but after experiments it looks like only particular FIFO thresholds work correctly. This bug is related to an earlier patch, which added special FIFO threshold configuration for OMAP3, because DSI command mode output didn't work with the normal threshold configuration. However, as the above work-around worked fine for other output types also, we currently always configure thresholds in this special way on OMAP3. In theory there should be negligible difference with this special way and the standard way. The first paragraph explains what happens in practice. This patch changes the driver to use the special threshold configuration only when the output is a manual update display on OMAP3. This does include RFBI displays also, and although it hasn't been tested (no boards using RFBI) I suspect the similar behaviour is present there also, as the DISPC side should work similarly for DSI command mode and RFBI. Signed-off-by:
-
- 21 May, 2012 1 commit
-
-
Archit Taneja authored
DSI supports interleaving of command mode packets during the HSA, HFP, HBP and BLLP blanking intervals in a video mode stream. This is useful as a user may want to read or change the configuration of a panel without stopping the video stream. On OMAP DSI, we can queue HS or LP command mode packets in the TX FIFO, and the DSI HW takes care of interleaving this data during the one of the blanking intervals. The DSI HW needs to be programmed with the maximum amount of data that can be interleaved in a particular blanking period. A blanking period cannot be used to send command mode data for it's complete duration, there is some amount of time required for the DSI data and clock lanes to transition to the desired LP or HS state. Based on the state of the lanes at the beginning and end of the blanking period, we have different scenarios, with each scenario having a different value of time required to transition to HS or LP. Refer to the section 'Interleaving Mode' in OMAP TRM for more info on the scenarios and the equations to calculate the time required for HS or LP transitions. We use the scenarios which takes the maximum time for HS or LP transition, this gives us the minimum amount of time that can be used to interleave command mode data. The amount of data that can be sent during this minimum time is calculated for command mode packets both in LP and HS. These are written to the registers DSI_VM_TIMING4 to DSI_VM_TIMING6. The calculations don't take into account the time required of transmitting BTA when doing a DSI read, or verifying if a DSI write went through correctly. Until these latencies aren't considered, the behaviour of DSI is unpredictable when a BTA is interleaved during a blanking period. Enhancement of these calculations is a TODO item. The calculations are derived from DSI parameter calculation tools written by Sebastien Fagard <s-fagard@ti.com> Signed-off-by:
-
- 15 May, 2012 1 commit
-
-
Chandrabhanu Mahapatra authored
DISPC has two accumulator registers DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1 each with horizontal and vertical bit fields. The bit fields can take values in the range of -1024 to 1023. Based on bit field values DISPC decides on which one out of 8 phases the filtering starts. DISPC_VIDp_ACCU_0 is used for progressive output and for interlaced output both DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1 are used. The current accumulator values in DISPC scaling logic for chroma plane takes default values for all color modes and rotation types. So, the horizontal and vertical up and downsampling accumulator bit field values have been updated for better performance. Signed-off-by:
-
- 13 May, 2012 13 commits
-
-
Timur Tabi authored
The THRESHOLDS register configures thresholds for two interrupts, but these interrupts are not used in the DIU driver. An early version of the driver may have used the "lines before vsync" interrupt, which requires the LS_BF_VS of THRESHOLDS to be initialized. Unfortunately, the initialization of this register does not do a read-modify-write to set only LS_BF_VS. On the MPC8610, the value written is correct. On other chips, like the P1022, the value overwrites some reserved bits. This results in a performance drop on the P1022. Since the default value is acceptable as-is on all SOCs, we should just avoid touching this register. Signed-off-by:
Timur Tabi <timur@freescale.com> Signed-off-by:
-
Donghwa Lee authored
This patch adds panel_reverse variable to support reversed s6e8ax0 panel type. Signed-off-by:
Donghwa Lee <dh09.lee@samsung.com> Signed-off-by:
Inki Dae <inki.dae@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Sylwester Nawrocki authored
Rework the interrupt handler so the RX_DONE, FIFO_EMPTY interrupts are properly detected. This prevents missing the interrupts when there are other bits set in the INTSRC register than just RX_DONE and FIFO_EMPTY. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Sylwester Nawrocki authored
Make sure all resources are initialized before interrupt handler is registered. Pass full platform device name to request_irq() so it can be distinguished which device has requested an interrupt in cases there are multiple instances in the system. Also enable voltage regulators regardless of they have been enabled by bootloader or not, to make sure other drivers using same regulators don't disable them unexpectedly. Signed-off-by:
-
Sylwester Nawrocki authored
Use proper PM ops from struct dev_pm_ops rather than the deprecated ones. Signed-off-by:
-
Kuninori Morimoto authored
Latest SuperH HDMI uses not only HDMI Core Register (HTOP0) but also HDMI Control Register (HTOP1). This patch adds HDMI Control Register support. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
Kuninori Morimoto authored
Latest SuperH HDMI allows 32bit access only. But the data is 8bit. So, we can keep compatibility by switching 8/32 bit access. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Donghwa Lee authored
MIPI DSI uses 1.1v regulator, so change its supply name. Signed-off-by:
-
Jingoo Han authored
This patch uses pr_debug instead of printk to allow dynamic debugging. Signed-off-by:
-
Jingoo Han authored
Remove unnecessary headers from the file. Signed-off-by:
-
Julia Lawall authored
Release bridge, as done on all other paths out of the function. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
- 11 May, 2012 10 commits
-
-
Tomi Valkeinen authored
Merge OMAP DSS HDMI audio patches from Ricardo Neri
-
Ricardo Neri authored
Implement the DSS device driver audio support interface in the HDMI panel driver and generic driver. The implementation relies on the IP-specific functions that are defined at DSS probe time. A mixed locking strategy is used. The panel's mutex is used when the state of the panel is queried as required by the audio functions. The audio state is protected using a spinlock as users of DSS HDMI audio functionality might start/stop audio while holding a spinlock. The mutex and the spinlock are held and released as needed by each individual function to protect the panel state and the audio state. Although the panel's audio_start functions does not check whether the panel is active, the audio _ENABLED state can be reached only from audio_enable, which does check the state of the panel. Also, if the panel is ever disabled, the audio state will transition to _DISABLED. Transitions are always protected by the audio lock. Signed-off-by: -
Ricardo Neri authored
As the hdmi_lock mutex is inside the hdmi struct, rename to simply "lock". This is only a change in the name. There are not changes in functionality. Signed-off-by: -
Ricardo Neri authored
As of today, the only know user of the DSS HDMI audio support is ASoC. Hence, it makes sense to remap the speaker order to match the ALSA speaker order. In the future, a dynamic mapping mechanism may be implemented. Remapping is needed as the HDMI speaker order is FL/FR/LFE/C/RL/RR/ RLC-FLC/RRC-FLC while the ALSA order is FL/FR/RL/RR/C/LFE/SL/SR. Refer to CEA-861 Section 6.6.2 for further details. Signed-off-by: -
Ricardo Neri authored
The generic HDMI driver does not need to know about the specific settings of a given IP. Hence, it just passes the audio configuration and the IP library parses such configuration and sets the IP accordingly. This patch introduces an IP-specific audio configuration function. Also, this patch implements the audio config function for OMAP4. The DMA, format and core config functions are no longer exposed to the generic HDMI driver as they are IP-specific. The audio configuration function caters for 16-bit through 24-bit audio samples with sample rates from 32kHz and up to 192kHz as well as up to 8 audio channels. Signed-off-by: -
Ricardo Neri authored
Add support for more sample rates when calculating N and CTS. This covers all the audio sample rates that an HDMI source is allowed to transmit according to the HDMI 1.4a specification. Also, reorganize the logic for the calculation when using deep color. Signed-off-by: -
Ricardo Neri authored
The N and CTS parameters are relevant to all HDMI implementations and not specific to a given IP. Hence, the calculation is relocated into the generic HDMI driver. Also, deep color is not queried but it is still considered in the calculation of N. This is to be changed when deep color functionality is implemented in the driver. Signed-off-by: -
Ricardo Neri authored
Utilize a snd_aes_iec958 struct to write the parameters of the IEC-60958 channel status word into the HDMI IP registers. Hence, the user of the driver has full control of what parameters are written in the word. Also, some of the parameters of the I2S structure have been removed as they are actually IEC-60958 parameters. Signed-off-by: -
Ricardo Neri authored
Instead of having OMAPDSS HDMI audio functionality depending on the ASoC HDMI audio driver, use a new config option so that potential users, including ASoC, may select if needed. Signed-off-by: -
Axel Castaneda Gonzalez authored
Decouple the enable/disable operation of the HDMI audio wrapper from audio start/stop. Otherwise, an audio FIFO underflow may occur. The audio wrapper enablement must be done after configuration and before audio playback is started. Signed-off-by:
Axel Castaneda Gonzalez <x0055901@ti.com> Signed-off-by:
-
