The UAS driver requires SG support by the HCD operating the device. This
patch stops UAS from operating on a HCD without sg support and prints a
message to let him know.

The spec says:
|For [USB2] backward compatibility, the device shall present [BOT] as
|alternate interface zero (primary) and [UAS] as alternate interface one
|(secondary). A device which does not need backward compatibility with
|[BOT] shall present [UAS] as alternate interface zero. In [USB2]
|systems, the [BOT] driver or an associated filter driver may need to
|issue a SET INTERFACE request for alternate interface one and then allow
|the [UAS] driver to load.

If the user used usb_modeswitch to switch to UAS then he can go back to
BOT or use a different HCD. In case UAS is the only interface then there
is currently no way out.
In future usb_sg_wait() should be extended to provide a non-blocking
interface so it can work with the UAS driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

Merge UAS bug fixes from Sebastian Andrzej Siewior, including some patches of
mine that he signed.

UAS fixes for Sarah

[v2: Editorial changes suggested by Sergei Shtylyov]

These modems use the Qualcomm MSM Interface (QMI) protocol for
management of their CDC ECM like wwan interface.  This driver
is perfect for exporting the protocol to userspace.

The created character device will be indistinguishable from a
common AT command based Device Management interface, so
userspace applications must do some intelligent matching
on the USB device.

Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Use ehci_setup() in ehci_ls1x_reset().

The Loongson1x SoCs have a built-in EHCI controller.
This patch adds the necessary glue code to make the generic EHCI
driver usable for them.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Use INCR8 mode for system bus interface of the USB controller
on MPC512x. This is a work-around for the AHB bus lock up
problem observed on MPC512x when there is heavy simultaneous
PATA write or network (FEC) activity.

See also "12.4 The USB controller can issue transactions that lock
up the AHB bus under certain conditions" in MPC5121e (M36P) Errata.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.ue>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb_register_dev() will change our .minor_base to 0 if
CONFIG_USB_DYNAMIC_MINORS is set.  And it usually is, of
course.

Use dev_name() to print the proper interface name instead
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The probe does not strictly require the USB_CDC_DMM_TYPE
descriptor, which is a good thing as it makes the driver
usable on non-conforming interfaces.  A user could e.g.
bind to it to a CDC ECM interface by using the new_id and
bind sysfs files.  But this would fail with a 0 buffer length
due to the missing descriptor.

Fix by defining a reasonable fallback size: The minimum
device receive buffer size required by the CDC WMC standard,
revision 1.1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

We don't need bMaxPacketSize0, and keeping all these different size fields
around will only cause us to use the wrong one.

Seems the udev variable was only used for getting bMaxPacketSize0.  We
could have used it for the usb_fill_*_urb() calls, but as it wasn't
before - why start now?  Instead make the interface_to_usbdev()
calls consistent.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

As Documentation/usb/dma.txt states:

  Most drivers should *NOT* be using these primitives; they don't need
  to use this type of memory (dma-coherent), and memory returned from
  kmalloc() will work just fine.

This driver handle only very low bandwith transfers.  It is not an
obvious candidate for usb_alloc_coherent().

Using these calls only serves to complicate the code for no gain,
as has been shown by multiple bugs related to this allocation path.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

As it turns out, there was a mismatch between the allocated inbuf size
(desc->bMaxPacketSize0, typically something like 64) and the length we
specified in the URB (desc->wMaxCommand, typically something like 2048)
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Filling the same URB with the exact same data is pointless.  It can be filled
once and resubmitted.  And not doing buffer allocation and URB filling at the
same place only serves to hide size mismatch bugs
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Remove superfluous newlines from debug statements.
Remove unnecessary line breaks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Preston Fick <preston.fick@silabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Enable usb-storage support dynamic id again by using a fixed id entry
that describes a device using the Bulk-Only transport with the
Transparent SCSI protocol.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Storage subdrivers, like alauda, datafab and others, don't support
dynamic  id currently, and it needs lots of work but with very little
gain to enable the feature, so disable them in the patch.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Commit 689d6eac ("USB: UHCI: add native scatter-gather support(v1))
added sg support to uhci but forgot to set the sg_table so this feature
remained unused.

Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This eliminates the last instance of a function's behavior
controlled by a parameter as Linus hates such things.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Do the cleanup to avoid behaviorial parameters Linus
requested.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Merge branches 'sched-urgent-for-linus', 'perf-urgent-for-linus' and 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/accounting, proc: Fix /proc/stat interrupts sum

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tracepoints/module: Fix disabling tracepoints with taint CRAP or OOT
  x86/kprobes: Add arch/x86/tools/insn_sanity to .gitignore
  x86/kprobes: Fix typo transferred from Intel manual

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
  x86, tsc: Fix SMI induced variation in quick_pit_calibrate()
  x86, opcode: ANDN and Group 17 in x86-opcode-map.txt
  x86/kconfig: Move the ZONE_DMA entry under a menu
  x86/UV2: Add accounting for BAU strong nacks
  x86/UV2: Ack BAU interrupt earlier
  x86/UV2: Remove stale no-resources test for UV2 BAU
  x86/UV2: Work around BAU bug
  x86/UV2: Fix BAU destination timeout initialization
  x86/UV2: Fix new UV2 hardware by using native UV2 broadcast mode
  x86: Get rid of dubious one-bit signed bitfield

gpio bug fixes for v3.3

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  gpio: tps65910: Use correct offset for gpio initialization
  gpio/it8761e: Restrict it8761e gpio driver to x86.
  gpio-ml-ioh: cleanup __iomem annotation usage
  gpio-ml-ioh: cleanup NULL pointer checking
  gpio-pch: cleanup __iomem annotation usage
  gpio-pch: cleanup NULL pointer checking

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  qnx4: don't leak ->BitMap on late failure exits
  qnx4: reduce the insane nesting in qnx4_checkroot()
  qnx4: di_fname is an array, for crying out loud...
  vfs: remove printk from set_nlink()
  wake up s_wait_unfrozen when ->freeze_fs fails

In checkin

  303395ac x86: Generate system call tables and unistd_*.h from tables

the feature macros in <asm/unistd.h> were unified between 32 and 64
bits.  Unfortunately 32 bits requires __ARCH_WANT_SYS_IPC and this was
inadvertently dropped.
Reported-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/CALLzPKbeXN5gdngo8uYYU8mAow=XhrwBFBhKfG811f37BubQOg@mail.gmail.com

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  KEYS: Permit key_serial() to be called with a const key pointer
  keys: fix user_defined key sparse messages
  ima: fix cred sparse warning
  MPILIB: Add a missing ENOMEM check

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

(struct qnx4_inode_entry *)(bh->b_data + some_offset)->di_fname
is not going to be NULL, TYVM...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Permit key_serial() to be called with a const key pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

Replace the rcu_assign_pointer() calls with rcu_assign_keypointer().
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

Fix ima_policy.c sparse "warning: dereference of noderef expression"
message, by accessing cred->uid using current_cred().

Changelog v1:
- Change __cred to just cred (based on David Howell's comment)
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>

Randy Dunlap reports that we get

  arch/x86/um/shared/sysdep/ptrace.h:7:20: error: redefinition of 'regs_return_value'
  arch/x86/um/shared/sysdep/ptrace.h:7:20: note: previous definition of 'regs_return_value' was here

when compiling UML for x86-64.

Stephen Rothwell root-caused it and says:

 "Caused by commit d7e7528b ("Audit: push audit success and retcode
  into arch ptrace.h") (another patch that was never in linux-next :-().

  This file now needs protection against double inclusion."

so let's do as the man says.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Analyzed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add a missing ENOMEM check.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>

* 'for-next-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  ib_srpt: Initial SRP Target merge for v3.3-rc1

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (26 commits)
  target: Set additional sense length field in sense data
  target: Remove legacy device status check from transport_execute_tasks
  target: Remove __transport_execute_tasks() for each processing context
  target: Remove extra se_device->execute_task_lock access in fast path
  target: Drop se_device TCQ queue_depth usage from I/O path
  target: Fix possible NULL pointer with __transport_execute_tasks
  target: Remove TFO->check_release_cmd() fabric API caller
  tcm_fc: Convert ft_send_work to use target_submit_cmd
  target: Add target_submit_cmd() for process context fabric submission
  target: Make target_put_sess_cmd use target_release_cmd_kref
  target: Set response format in INQUIRY response
  target: tcm_mod_builder: small fixups
  Documentation/target: Fix tcm_mod_builder.py build breakage
  target: remove overagressive ____cacheline_aligned annoations
  tcm_loop: bump max_sectors
  target/configs: remove trailing newline from udev_path and alias
  iscsi-target: fix chap identifier simple_strtoul usage
  target: remove useless casts
  target: simplify target_check_cdb_and_preempt
  target: Move core_scsi3_check_cdb_abort_and_preempt
  ...

This includes initial support for the recently published ACPI 5.0 spec.
In particular, support for the "hardware-reduced" bit that eliminates
the dependency on legacy hardware.

APEI has patches resulting from testing on real hardware.

Plus other random fixes.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (52 commits)
  acpi/apei/einj: Add extensions to EINJ from rev 5.0 of acpi spec
  intel_idle: Split up and provide per CPU initialization func
  ACPI processor: Remove unneeded variable passed by acpi_processor_hotadd_init V2
  ACPI processor: Remove unneeded cpuidle_unregister_driver call
  intel idle: Make idle driver more robust
  intel_idle: Fix a cast to pointer from integer of different size warning in intel_idle
  ACPI: kernel-parameters.txt : Add intel_idle.max_cstate
  intel_idle: remove redundant local_irq_disable() call
  ACPI processor: Fix error path, also remove sysdev link
  ACPI: processor: fix acpi_get_cpuid for UP processor
  intel_idle: fix API misuse
  ACPI APEI: Convert atomicio routines
  ACPI: Export interfaces for ioremapping/iounmapping ACPI registers
  ACPI: Fix possible alignment issues with GAS 'address' references
  ACPI, ia64: Use SRAT table rev to use 8bit or 16/32bit PXM fields (ia64)
  ACPI, x86: Use SRAT table rev to use 8bit or 32bit PXM fields (x86/x86-64)
  ACPI: Store SRAT table revision
  ACPI, APEI, Resolve false conflict between ACPI NVS and APEI
  ACPI, Record ACPI NVS regions
  ACPI, APEI, EINJ, Refine the fix of resource conflict
  ...

This patch fixes an (ACPI S3) suspend regression introduced in commit
68d6e671 ("tpm: Introduce function to poll for result of self test")
and occurring with an Infineon TPM and tpm_tis and tpm_infineon drivers
active.

The suspend problem occurred if the TPM was disabled and/or deactivated
and therefore the TPM_PCRRead checking the result of the (asynchronous)
self test returned an error code which then caused the tpm_tis driver to
become inactive and this then seemed to have negatively influenced the
suspend support by the tpm_infineon driver...  Besides that the tpm_tis
drive may stay active even if the TPM is disabled and/or deactivated.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The type of 'make_request_fn' changed in 5a7bbad2 ("block: remove
support for bio remapping from ->make_request"), but the merge of the
nvme driver didn't take that into account, and as a result the driver
would compile with a warning:

  drivers/block/nvme.c: In function 'nvme_alloc_ns':
  drivers/block/nvme.c:1336:2: warning: passing argument 2 of 'blk_queue_make_request' from incompatible pointer type [enabled by default]
  include/linux/blkdev.h:830:13: note: expected 'void (*)(struct request_queue *, struct bio *)' but argument is of type 'int (*)(struct request_queue *, struct bio *)'

It's benign, but the warning is annoying.
Reported-by: Stephen Rothwell <sfr@canb.auug.org>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix these warnings:

  drivers/xen/biomerge.c:14:1: warning: data definition has no type or storage class [enabled by default]
  drivers/xen/biomerge.c:14:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
  drivers/xen/biomerge.c:14:1: warning: parameter names (without types) in function declaration [enabled by default]

And this build error:

  ERROR: "xen_biovec_phys_mergeable" [drivers/block/nvme.ko] undefined!
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus/i2c-33' of git://git.fluff.org/bjdooks/linux:
  i2c-eg20t: Change-company-name-OKI-SEMICONDUCTOR to LAPIS Semiconductor
  i2c-eg20t: Support new device LAPIS Semiconductor ML7831 IOH
  i2c-eg20t: modified the setting of transfer rate.
  i2c-eg20t: use i2c_add_numbered_adapter to get a fixed bus number
  i2c: OMAP: Add DT support for i2c controller
  I2C: OMAP: NACK without STP
  I2C: OMAP: correct SYSC register offset for OMAP4

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (57 commits)
  [media] as3645a: Fix compilation by including slab.h
  [media] s5p-fimc: Remove linux/version.h include from fimc-mdevice.c
  [media] s5p-mfc: Remove linux/version.h include from s5p_mfc.c
  [media] ds3000: using logical && instead of bitwise &
  [media] v4l2-ctrls: make control names consistent
  [media] DVB: dib0700, add support for Nova-TD LEDs
  [media] DVB: dib0700, add corrected Nova-TD frontend_attach
  [media] DVB: dib0700, separate stk7070pd initialization
  [media] DVB: dib0700, move Nova-TD Stick to a separate set
  [media] : add MODULE_FIRMWARE to dib0700
  [media] DVB-CORE: remove superfluous DTV_CMDs
  [media] s5p-jpeg: adapt to recent videobuf2 changes
  [media] s5p-g2d: fixed a bug in controls setting function
  [media] s5p-mfc: Fix volatile controls setup
  [media] drivers/media/video/s5p-mfc/s5p_mfc.c: adjust double test
  [media] drivers/media/video/s5p-fimc/fimc-capture.c: adjust double test
  [media] s5p-fimc: Fix incorrect control ID assignment
  [media] dvb_frontend: Don't call get_frontend() if idle
  [media] DocBook/dvbproperty.xml: Remove DTV_MODULATION from ISDB-T
  [media] DocBook/dvbproperty.xml: Fix ISDB-T delivery system parameters
  ...