- 13 Jun, 2021 14 commits
-
-
Yang Yingliang authored
Disable reg and clk when devm_gpiod_get_optional() fails in adf4350_probe(). Fixes:4a89d2f4 ("iio: adf4350: Convert to use GPIO descriptor") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210601142605.3613605-1-yangyingliang@huawei.com Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Stephan Gerhold authored
According to the BMA253 datasheet [1] and BMA250 datasheet [2] the bandwidth value for BMA25x should be set as 01xxx: "Settings 00xxx result in a bandwidth of 7.81 Hz; [...] It is recommended [...] to use the range from ´01000b´ to ´01111b´ only in order to be compatible with future products." However, at the moment the drivers sets bandwidth values from 0 to 6, which is not recommended and always results into 7.81 Hz bandwidth according to the datasheet. Fix this by introducing a bw_offset = 8 = 01000b for BMA25x, so the additional bit is always set for BMA25x. [1]: https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bma253-ds000.pdf [2]: https://datasheet.octopart.com/BMA250-Bosch-datasheet-15540103.pdf Cc: Peter Meerwald <pmeerw@pmeerw.net> Fixes: 2017cff2 ("iio:bma180: Add BMA250 chip support") Signed-off-by:
Stephan Gerhold <stephan@gerhold.net> Reviewed-by:
-
Jarkko Nikula authored
Use to_pci_dev() helper instead of container_of(d, struct pci_dev, dev); Suggested-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by:
William Breathitt Gray <vilhelm.gray@gmail.com> Link: https://lore.kernel.org/r/20210611115558.796338-2-jarkko.nikula@linux.intel.comSigned-off-by:
-
Jarkko Nikula authored
Remove CONFIG_PM ifdef and mark PM callbacks with __maybe_unused. Suggested-by:
-
Alexandru Ardelean authored
These were usually used before the conversion to devm_ functions, so that the remove hook would be able to retrieve the pointer and do cleanups on remove. When the conversion happened, they should have been removed, but were omitted. Some drivers were copied from drivers that fit the criteria described above. In any case, in order to prevent more drivers from being used as example (and have spi_set_drvdata() needlessly set), this change removes it from the IIO ADC group. Signed-off-by:
Alexandru Ardelean <aardelean@deviqon.com> Link: https://lore.kernel.org/r/20210513111035.77950-1-aardelean@deviqon.comSigned-off-by:
-
Alexandru Ardelean authored
These were usually used before the conversion to devm_ functions, so that the remove hook would be able to retrieve the pointer and do cleanups on remove. When the conversion happened, they should have been removed, but were omitted. Some drivers were copied from drivers that fit the criteria described above. In any case, in order to prevent more drivers from being used as example (and have spi_set_drvdata() needlessly set), this change removes it from the IIO IMU group. Signed-off-by:
-
Alexandru Ardelean authored
Since all AD Sigma-Delta drivers now use the devm_ad_sd_setup_buffer_and_trigger() function, we can remove the old ad_sd_{setup,cleanup}_buffer_and_trigger() functions. This way we can discourage new drivers that use the ad_sigma_delta lib-driver to use these (older functions). Signed-off-by: -
Jonathan Cameron authored
As not many steps were not already devm_ managed, use devm_add_action_or_reset() to handle the rest. This also uses the new devm_ad_sd_setup_buffer_and_trigger() function. Reviewed-by:
Alexandru Ardelean <ardeleanalex@gmail.com> Signed-off-by:
-
Alexandru Ardelean authored
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier now to convert the probe of the AD7192 driver to use device-managed functions. The regulators and the mclk requires devm_add_action_or_reset() callbacks though. Signed-off-by:
-
Alexandru Ardelean authored
The devm_clk_get_optional() helper returns NULL when devm_clk_get() returns -ENOENT. This makes things slightly cleaner. The added benefit is mostly cosmetic. Also, a minor detail with this call, is that the reference for the parent device is taken as `spi->dev` instead of `&st->sd.spi->dev` (which looks a little quirky). Signed-off-by:
-
Alexandru Ardelean authored
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier now to convert the probe of the AD7780 driver to use device-managed functions. Only the regulator disable requires a devm_add_action_or_reset() callback. This change does that, cleaning up the driver a bit. Signed-off-by:
-
Alexandru Ardelean authored
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier now to convert the probe of the AD7791 driver to use device-managed functions. Only the regulator disable requires a devm_add_action_or_reset() callback. This change does that, cleaning up the driver a bit. Signed-off-by:
-
Alexandru Ardelean authored
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier now to convert the probe of the AD7793 driver to use device-managed functions. Only the regulator disable requires a devm_add_action_or_reset() callback. This change does that, cleaning up the driver a bit. Signed-off-by:
-
Alexandru Ardelean authored
This is a version of ad_sd_setup_buffer_and_trigger() with all underlying functions (that are used) being replaced with their device-managed variants. One thing to take care here is with {devm_}iio_trigger_alloc(), where both functions take a parent-device object as the first parameter. To make sure nothing quirky is happening, the devm_ad_sd_probe_trigger() function is checking that the provided 'dev' reference is the same as the one stored on the 'struct ad_sigma_delta' driver data. Signed-off-by:
-
- 09 Jun, 2021 26 commits
-
-
Hans de Goede authored
Some Yoga laptops with 1 accelerometer in the display and 1 in the base, use an ACPI HID of DUAL250E instead of BOSC0200. Set the iio-device's label for DUAL250E devices to a value indicating which sensor is which, mirroring how we do this for BOSC0200 dual sensor devices. Note the DUAL250E fwnode unfortunately does not include a mount-matrix. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20210523170103.176958-10-hdegoede@redhat.comSigned-off-by:
-
Hans de Goede authored
Factor the BOSC0200 ACPI HID handling out into a new bmc150_apply_bosc0200_acpi_orientation() function and make bmc150_apply_acpi_orientation() call that when dealing with a BOSC0200 ACPI device (and make it return false otherwise). This is a preparation patch for adding special handling for other ACPI HIDs (the "DUAL250E" HID). Suggested-by:
-
Hans de Goede authored
Some 360 degree hinges (yoga) style 2-in-1 devices use 2 bmc150 accels to allow the OS to determine the angle between the display and the base of the device, so that the OS can determine if the 2-in-1 is in laptop or in tablet-mode. On Windows both accelerometers are read (polled) by a special service and this service calls the DSM (Device Specific Method), which in turn translates the angles to one of laptop/tablet/tent/stand mode and then notifies the EC about the new mode and the EC then enables or disables the builtin keyboard and touchpad based in the mode. When the 2-in-1 is powered-on or resumed folded in tablet mode the EC senses this independent of the DSM by using a HALL effect sensor which senses that the keyboard has been folded away behind the display. At power-on or resume the EC disables the keyboard based on this and the only way to get the keyboard to work after this is to call the DSM to re-enable it. Call the DSM on probe() and resume() to fix the keyboard not working when powered-on / resumed in tablet-mode. This patch was developed and tested on a Lenovo Yoga 300-IBR. Signed-off-by:
-
Hans de Goede authored
Now that the definition of the bmc150_accel_data struct is no longer private to bmc150-accel-core.c, bmc150-accel-i2c.c can simply directly access the second_dev member and the accessor functions are no longer necessary. Note if the i2c_acpi_new_device() for the second-client now fails, an ERR_PTR gets stored in data->second_dev this is fine since it is only ever passed to i2c_unregister_device() which has an IS_ERR_OR_NULL() check. Signed-off-by:
-
Hans de Goede authored
Further patches to bmc150-accel-i2c.c need to store some extra info (on top of the second_dev pointer) in the bmc150_accel_data struct, rather then adding yet more accessor functions for this lets just move the struct bmc150_accel_data definition to bmc150-accel.h. Signed-off-by:
-
Hans de Goede authored
The Lenovo Yoga 300-11IBR has a ACPI fwnode with a HID of DUAL250E which contains I2C and IRQ resources for 2 accelerometers, 1 in the display and one in the base of the device. Add support for this. Signed-off-by:
-
Hans de Goede authored
Move the check for a second ACPI device for BOSC0200 ACPI fwnodes into a new bmc150_acpi_dual_accel_probe() helper function. This is a preparation patch for adding support for a new "DUAL250E" ACPI Hardware-ID (HID) used on some devices. Signed-off-by:
-
Hans de Goede authored
On machines with dual accelerometers described in a single ACPI fwnode, the bmc150_accel_probe() instantiates a second i2c-client for the second accelerometer. A pointer to this manually instantiated second i2c-client is stored inside the iio_dev's private-data through bmc150_set_second_device(), so that the i2c-client can be unregistered from bmc150_accel_remove(). Before this commit bmc150_set_second_device() took only 1 argument so it would store the pointer in private-data of the iio_dev belonging to the manually instantiated i2c-client, leading to the bmc150_accel_remove() call for the second_dev trying to unregister *itself* while it was being removed, leading to a deadlock and rmmod hanging. Change bmc150_set_second_device() to take 2 arguments: 1. The i2c-client which is instantiating the second i2c-client for the 2nd accelerometer and 2. The second-device pointer itself (which also is an i2c-client). This will store the second_device pointer in the private data of the iio_dev belonging to the (ACPI instantiated) i2c-client for the first accelerometer and will make bmc150_accel_remove() unregister the second_device i2c-client when called for the first client, avoiding the deadlock. Fixes: 5bfb3a4b ("iio: accel: bmc150: Check for a second ACPI device for BOSC0200") Cc: Jeremy Cline <jeremy@jcline.org> Signed-off-by:
-
Hans de Goede authored
The drvdata for iio-parent devices points to the struct iio_dev for the iio-device. So by directly casting the return from i2c_get_clientdata() to struct bmc150_accel_data * the code was ending up storing the second_dev pointer in (and retrieving it from) some semi-random offset inside struct iio_dev, rather then storing it in the second_dev member of the bmc150_accel_data struct. Fix the code to get the struct bmc150_accel_data * pointer to call iio_priv() on the struct iio_dev * returned by i2c_get_clientdata(), so that the correct pointer gets dereferenced. This fixes the following oops on rmmod, caused by trying to dereference the wrong return of bmc150_get_second_device(): [ 238.980737] BUG: unable to handle page fault for address: 0000000000004710 [ 238.980755] #PF: supervisor read access in kernel mode [ 238.980760] #PF: error_code(0x0000) - not-present page ... [ 238.980841] i2c_unregister_device.part.0+0x19/0x60 [ 238.980856] 0xffffffffc0815016 [ 238.980863] i2c_device_remove+0x25/0xb0 [ 238.980869] __device_release_driver+0x180/0x240 [ 238.980876] driver_detach+0xd4/0x120 [ 238.980882] bus_remove_driver+0x5b/0xd0 [ 238.980888] i2c_del_driver+0x44/0x70 While at it also remove the now no longer sensible checks for data being NULL, iio_priv never returns NULL for an iio_dev with non 0 sized private-data. Fixes: 5bfb3a4b ("iio: accel: bmc150: Check for a second ACPI device for BOSC0200") Cc: Jeremy Cline <jeremy@jcline.org> Signed-off-by:
-
Jonathan Cameron authored
Since: commit cbacb5ab ("docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]") use of these format strings has been discouraged. As there are only a few such instances in IIO, this is part of a series clearing them out so they don't get copied into new drivers. Use the 0x02x form as the length specifier when used with # includes the 0x prefix and is very unlikely to be what was intended by the author. Signed-off-by:
Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/r/20210603180612.3635250-5-jic23@kernel.org
-
Jonathan Cameron authored
Since: commit cbacb5ab ("docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]") use of these format strings has been discouraged. Use the 0x02x form as the length specifier when used with # includes the 0x prefix and is very unlikely to be what was intended by the author. Part of a series removing all uses from IIO in the interestings of avoiding providing bad examples for people to copy. Signed-off-by:
-
Jonathan Cameron authored
Since: commit cbacb5ab ("docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]") use of these format strings has been discouraged. Use the 0x02x form as the length specifier when used with # includes the 0x prefix and is very unlikely to be what was intended by the author. As there are not that many in IIO, this is part of an effort to clear them out so we don't have any instances that might get copied into new drivers. Signed-off-by:
-
Arnd Bergmann authored
clang complains about multiple instances of printing an integer using the %hhx format string: drivers/iio/light/si1133.c:982:4: error: format specifies type 'unsigned char' but the argument has type 'unsigned int' [-Werror,-Wformat] part_id, rev_id, mfr_id); ^~~~~~~ Print them as a normal integer instead, leaving the "#02" length modifier. Use the 0x02x form as the length specifier when used with # includes the 0x prefix and is very unlikely to be what was intended by the author. Fixes: e01e7eaf ("iio: light: introduce si1133") Signed-off-by:Arnd Bergmann <arnd@arndb.de> Cc: Nathan Chancellor <nathan@kernel.org> Signed-off-by:
-
William Breathitt Gray authored
The struct counter_synapse actions_list member expects a const enum counter_synapse_action array. This patch adds the const qualifier to the stm32_synapse_actions to match actions_list. Cc: Benjamin Gaignard <benjamin.gaignard@st.com> Reviewed-by:
Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by:
-
William Breathitt Gray authored
The struct counter_synapse actions_list member expects a const enum counter_synapse_action array. This patch adds the const qualifier to the stm32_lptim_cnt_synapse_actions to match actions_list. Reviewed-by:
-
William Breathitt Gray authored
The struct counter_synapse actions_list member expects a const enum counter_synapse_action array. This patch adds the const qualifier to the mchp_tc_synapse_actions to match actions_list. Cc: Kamel Bouhara <kamel.bouhara@bootlin.com> Signed-off-by:
-
William Breathitt Gray authored
The struct counter_synapse actions_list member expects a const enum counter_synapse_action array. This patch adds the const qualifier to the ftm_quaddec_synapse_actions to match actions_list. Cc: Patrick Havelange <patrick.havelange@essensium.com> Signed-off-by:
-
William Breathitt Gray authored
The struct counter_synapse actions_list member expects a const enum counter_synapse_action array. This patch adds the const qualifier to the quad8_index_actions_list and quad8_synapse_actions_list to match actions_list. Acked-by:
Syed Nayyar Waris <syednwaris@gmail.com> Signed-off-by:
-
William Breathitt Gray authored
The struct counter_count functions_list member expects a const enum counter_count_function array. This patch adds the const qualifier to the stm32_count_functions to match functions_list. Cc: Benjamin Gaignard <benjamin.gaignard@st.com> Reviewed-by:
-
William Breathitt Gray authored
The struct counter_count functions_list member expects a const enum counter_count_function array. This patch adds the const qualifier to the stm32_lptim_cnt_functions to match functions_list. Reviewed-by:
-
William Breathitt Gray authored
The struct counter_count functions_list member expects a const enum counter_count_function array. This patch adds the const qualifier to the mchp_tc_count_functions to match functions_list. Cc: Kamel Bouhara <kamel.bouhara@bootlin.com> Signed-off-by:
-
William Breathitt Gray authored
The struct counter_count functions_list member expects a const enum counter_count_function array. This patch adds the const qualifier to the interrupt__cnt_functions to match functions_list. Cc: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
William Breathitt Gray authored
The struct counter_count functions_list member expects a const enum counter_count_function array. This patch adds the const qualifier to the quad8_count_functions_list to match functions_list. Acked-by:
-
William Breathitt Gray authored
Add some safety by qualifying the quad8_preset_register_set() function parameters as const. Acked-by:
-
William Breathitt Gray authored
When the kernel is running in secure boot mode, we lock down the kernel to prevent userspace from modifying the running kernel image. Whilst this includes prohibiting access to things like /dev/mem, it must also prevent access by means of configuring driver modules in such a way as to cause a device to access or modify the kernel image. To this end, annotate module_param* statements that refer to hardware configuration and indicate for future reference what type of parameter they specify. The parameter parser in the core sees this information and can skip such parameters with an error message if the kernel is locked down. The module initialisation then runs as normal, but just sees whatever the default values for those parameters is. Note that we do still need to do the module initialisation because some drivers have viable defaults set in case parameters aren't specified and some drivers support automatic configuration (e.g. PNP or PCI) in addition to manually coded parameters. This patch annotates the 104-QUAD-8 driver. Acked-by:
-
William Breathitt Gray authored
It is obvious that devm_counter_register() is used to register a Counter device, so a comment stating such is pointless here. Acked-by:
-
