- 17 Jan, 2014 1 commit
-
-
Paul Bolle authored
Building resource_tracker.o triggers a GCC warning: drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_HW2SW_CQ_wrapper': drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:3019:16: warning: 'cq' may be used uninitialized in this function [-Wmaybe-uninitialized] atomic_dec(&cq->mtt->ref_count); ^ This is a false positive. But a cleanup of cq_res_start_move_to() can help GCC here. The code currently uses a switch statement where an if/else construct would do too, since only two of the switch's four cases can ever occur. Dropping that switch makes the warning go away. While we're at it, add some missing braces. Signed-off-by:Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 16 Jan, 2014 39 commits
-
-
David S. Miller authored
Aaron Brown says: ==================== Intel Wired LAN Driver Updates This series contains updates to ixgbe and ixgbevf. John adds rtnl lock / unlock semantics for ixgbe_reinit_locked() which was being called without the rtnl lock being held. Jacob corrects an issue where ixgbevf_qv_disable function does not set the disabled bit correctly. From the community, Wei uses a type of struct for pci driver-specific data in ixgbevf_suspend() Don changes the way we store ring arrays in a manner that allows support of multiple queues on multiple nodes and creates new ring initialization functions for work previously done across multiple functions - making the code closer to ixgbe and hopefully more readable. He also fixes incorrect fiber eeprom write logic. ==================== Signed-off-by: -
Don Skidmore authored
In this code we wanted to set the bit in IXGBE_SFF_SOFT_RS_SELECT_MASK to the value in rs. So we really needed a logical or rather than an and, this patch makes that change. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
-
Don Skidmore authored
This patch creates new functions for ring initialization, ixgbevf_configure_tx_ring() and ixgbevf_configure_rx_ring(). The work done in these function previously was spread between several other functions and this change should hopefully lead to greater readability and make the code more like ixgbe. This patch also moves the placement of some older functions to avoid having to write prototypes. It also promotes a couple of debug messages to errors. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by:
-
Don Skidmore authored
This will change how we store rings arrays in the adapter sturct. We use to have a pointer to an array now we will be using an array of pointers. This will allow us to support multiple queues on muliple nodes at some point we would be able to reallocate the rings so that each is on a local node if needed. Signed-off-by:
-
Wei Yongjun authored
We had set the pci driver-specific data in ixgbevf_probe() as a type of struct net_device, so we should use it as netdev in ixgbevf_suspend(). Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Tested-by:
-
Jacob Keller authored
The ixgbevf_qv_disable function used by CONFIG_NET_RX_BUSY_POLL is broken, because it does not properly set the IXGBEVF_QV_STATE_DISABLED bit, indicating that the q_vector should be disabled (and preventing future locks from obtaining the vector). This patch corrects the issue by setting the disable state. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
John Fastabend authored
ixgbe_service_task() is calling ixgbe_reinit_locked() without the rtnl_lock being held. This is because it is being called from a worker thread and not a rtnl netlink or dcbnl path. Add rtnl_{un}lock() semantics. I found this during code review. Signed-off-by:John Fastabend <john.r.fastabend@intel.com> Tested-by:
-
Eric Dumazet authored
eth_type_trans() can read uninitialized memory as drivers do not necessarily pull more than 14 bytes in skb->head before calling it. As David suggested, we can use skb_header_pointer() to fix this without breaking some drivers that might not expect eth_type_trans() pulling 2 additional bytes. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
David S. Miller authored
Srinivas Kandagatla says: ==================== net: stmmac PM related fixes. During PM_SUSPEND_FREEZE testing, I have noticed that PM support in STMMAC is partly broken. I had to re-arrange the code to do PM correctly. There were lot of things I did not like personally and some bits did not work in the first place. I thought this is the nice opportunity to clean the mess up. Here is what I did: any 1> Test PM suspend freeze via pm_test It did not work for following reasons. - If the power to gmac is removed when it enters in low power state. stmmac_resume could not cope up with such behaviour, it was expecting the ip register contents to be still same as before entering low power, This assumption is wrong. So I started to add some code to do Hardware initialization, thats when I started to re-arrange the code. stmmac_open contains both resource and memory allocations and hardware initialization. I had to separate these two things in two different functions. These two patches do that net: stmmac: move dma allocation to new function net: stmmac: move hardware setup for stmmac_open to new function And rest of the other patches are fixing the loose ends, things like mdio reset, which might be necessary in cases likes hibernation(I did not test). In hibernation cases the driver was just unregistering with subsystems and releasing resources which I did not like and its not necessary to do this as part of PM. So using the same stmmac_suspend/resume made more sense for hibernation cases than using stmmac_open/release. Also fixed a NULL pointer dereference bug too. 2> Test WOL via PM_SUSPEND_FREEZE Did get an wakeup interrupt, but could not wakeup a freeze system. So I had to add pm_wakeup_event to the driver. net: stmmac: notify the PM core of a wakeup event. patch. Also few patches like net: stmmac: make stmmac_mdio_reset non-static net: stmmac: restore pinstate in pm resume. helps the resume function to reset the phy and put back the pins in default state. Changes since RFC: - Rebased to net-next on Dave's suggestion. All these patches are Acked by Peppe. ==================== Signed-off-by: -
Srinivas Kandagatla authored
In PM_SUSPEND_FREEZE and WOL(Wakeup On Lan) case, when the driver gets a wakeup event, either the driver or platform specific PM code should notify the pm core about it, so that the system can wakeup from low power. In cases where there is no involvement of platform specific PM, it becomes driver responsibility to notify the PM core to wakeup the system. Without this WOL with PM_SUSPEND_FREEZE does not work on STi based SOCs. Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@st.com> Acked-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
-
Srinivas Kandagatla authored
This patch adds code to restore default pinstate of the pins when it comes back from low power state. Without this patch the state of the pins would be unknown and the driver would not work. This patch also adds code to put the pins in to sleep state when the driver enters low power state. Signed-off-by:
-
Srinivas Kandagatla authored
In hibernation freeze case the driver just releases the resources like dma buffers, irqs, unregisters the drivers and during restore it does register, request the resources. This is not really necessary, as part of power management all the data structures are intact, all the previously allocated resources can be used after coming out of low power. This patch uses the suspend and resume callbacks for freeze and restore which initializes the hardware correctly without unregistering or releasing the resources, this should also help in reducing the time to restore. Also this patch fixes a bug in stmmac_pltfr_restore and stmmac_pltfr_freeze where it tries to get hold of platform data via dev_get_platdata call, which would return NULL in device tree cases and the next if statement would crash as there is no NULL check. Signed-off-by:
-
Srinivas Kandagatla authored
The driver PM resume assumes that the IP is still powered up and the all the register contents are not disturbed when it comes out of low power suspend case. This assumption is wrong, basically the driver should not consider any state of registers after it comes out of low power. However driver can keep the part of the IP powered up if its a wake up source. But it can not assume the register state of the IP. Also its possible that SOC glue layer can take the power off the IP if its not wake-up source to reduce the power consumption. This patch re initializes hardware by calling stmmac_hw_setup function in resume case. Signed-off-by:
-
Srinivas Kandagatla authored
This patch promotes stmmac_mdio_reset function from static to non-static, so that power management functions can decide to reset if the IP comes out from lowe power state specially hibernation cases. Signed-off-by:
-
Srinivas Kandagatla authored
This patch moves hardware setup part of the code in stmmac_open to a new function stmmac_hw_setup, the reason for doing this is to make hw initialization independent function so that PM functions can re-use it to re-initialize the IP after returning from low power state. This will also avoid code duplication across stmmac_resume/restore and stmmac_open. Signed-off-by:
-
Srinivas Kandagatla authored
This patch moves dma resource allocation to a new function alloc_dma_desc_resources, the reason for moving this to a new function is to keep the memory allocations in a separate function. One more reason it to get suspend and hibernation cases working without releasing and allocating these resources during suspend-resume and freeze-restore cases. Signed-off-by:
-
Srinivas Kandagatla authored
This patch removes gpio_free for reset line of the phy, driver stores the gpio number in its private data-structure to use in future. As the driver uses this pin in future this pin should not be freed. Signed-off-by:
-
Srinivas Kandagatla authored
This patch adds support to "max-speed" property which is a standard Ethernet device tree property. max-speed specifies maximum speed (specified in megabits per second) supported the device. Depending on the clocking schemes some of the boards can only support few link speeds, so having a way to limit the link speed in the mac driver would allow such setups to work reliably. Without this patch there is no way to tell the driver to limit the link speed. Signed-off-by:
-
David S. Miller authored
Willy Tarreau says: ==================== Assorted mvneta fixes and improvements this series provides some fixes for a number of issues met with the mvneta driver, then adds some improvements. Patches 1-5 are fixes and would be needed in 3.13 and likely -stable. The next ones are performance improvements and cleanups : - driver lockup when reading stats while sending traffic from multiple CPUs : this obviously only happens on SMP and is the result of missing locking on the driver. The problem was present since the introduction of the driver in 3.8. The first patch performs some changes that are needed for the second one which actually fixes the issue by using per-cpu counters. It could make sense to backport this to the relevant stable versions. - mvneta_tx_timeout calls various functions to reset the NIC, and these functions sleep, which is not allowed here, resulting in a panic. Better completely disable this Tx timeout handler for now since it is never called. The problem was encountered while developing some new features, it's uncertain whether it's possible to reproduce it with regular usage, so maybe a backport to stable is not needed. - replace the Tx timer with a real Tx IRQ. As first reported by Arnaud Ebalard and explained by Eric Dumazet, there is no way this driver can work correctly if it uses a driver to recycle the Tx descriptors. If too many packets are sent at once, the driver quickly ends up with no descriptors (which happens twice as easily in GSO) and has to wait 10ms for recycling its descriptors and being able to send again. Eric has worked around this in the core GSO code. But still when routing traffic or sending UDP packets, the limitation is very visible. Using Tx IRQs allows Tx descriptors to be recycled when sent. The coalesce value is still configurable using ethtool. This fix turns the UDP send bitrate from 134 Mbps to 987 Mbps (ie: line rate). It's made of two patches, one to add the relevant bits from the original Marvell's driver, and another one to implement the change. I don't know if it should be backported to stable, as the bug only causes poor performance. - Patches 6..8 are essentially cleanups, code deduplication and minor optimizations for not re-fetching a value we already have (status). - patch 9 changes the prefetch of Rx descriptor from current one to next one. In benchmarks, it results in about 1% general performance increase on HTTP traffic, probably because prefetching the current descriptor does not leave enough time between the start of prefetch and its usage. - patch 10 implements support for build_skb() on Rx path. The driver now preallocates frags instead of skbs and builds an skb just before delivering it. This results in a 2% performance increase on HTTP traffic, and up to 5% on small packet Rx rate. - patch 11 implements rx_copybreak for small packets (256 bytes). It avoids a dma_map_single()/dma_unmap_single() and increases the Rx rate by 16.4%, from 486kpps to 573kpps. Further improvements up to 711kpps are possible depending how the DMA is used. - patches 12 and 13 are extra cleanups made possible by some of the simplifications above. ==================== Signed-off-by: -
Arnaud Ebalard authored
The function return parameter is not used in mvneta_tx_done_gbe(), where the function is called. This patch makes the function return void. Reviewed-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
Arnaud Ebalard <arno@natisbad.org> Signed-off-by:
-
Arnaud Ebalard authored
mvneta_tx_done_gbe() return value and third parameter are no more used. This patch changes the function prototype and removes a useless variable where the function is called. Reviewed-by:
-
willy tarreau authored
calling dma_map_single()/dma_unmap_single() is quite expensive compared to copying a small packet. So let's copy short frames and keep the buffers mapped. We set the limit to 256 bytes which seems to give good results both on the XP-GP board and on the AX3/4. The Rx small packet rate increased by 16.4% doing this, from 486kpps to 573kpps. It is worth noting that even the call to the function dma_sync_single_range_for_cpu() is expensive (300 ns) although less than dma_unmap_single(). Without it, the packet rate raises to 711kpps (+24% more). Thus on systems where coherency from device to CPU is guaranteed by a snoop control unit, this patch should provide even more gains, and probably rx_copybreak could be increased. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by:
-
willy tarreau authored
Make use of build_skb() to allocate frags on the RX path. When frag size is lower than a page size, we can use netdev_alloc_frag(), and we fall back to kmalloc() for larger sizes. The frag size is stored into the mvneta_port struct. The alloc/free functions check the frag size to decide what alloc/ free method to use. MTU changes are safe because the MTU change function stops the device and clears the queues before applying the change. With this patch, I observed a reproducible 2% performance improvement on HTTP-based benchmarks, and 5% on small packet RX rate. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by:
-
willy tarreau authored
Currently, the mvneta driver tries to prefetch the current Rx descriptor during read. Tests have shown that prefetching the next one instead increases general performance by about 1% on HTTP traffic. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by:
-
willy tarreau authored
At several places, we already know the value of the rx status but we call functions which dereference the pointer again to get it and don't need the descriptor for anything else. Simplify this task by replacing the rx desc pointer by the status word itself. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by:
-
willy tarreau authored
Make mvneta_rxq_fill() use mvneta_rx_refill() instead of using duplicate code. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by:
-
willy tarreau authored
Currently, mvneta_txq_bufs_free() calls mvneta_tx_done_policy() with a non-null cause to retrieve the pointer to the next queue to process. There are useless tests on the return queue number and on the pointer, all of which are well defined within a known limited set. This code path is fast, although not critical. Removing 3 tests here that the compiler could not optimize (verified) is always desirable. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by:
-
willy tarreau authored
Right now the mvneta driver doesn't handle Tx IRQ, and relies on two mechanisms to flush Tx descriptors : a flush at the end of mvneta_tx() and a timer. If a burst of packets is emitted faster than the device can send them, then the queue is stopped until next wake-up of the timer 10ms later. This causes jerky output traffic with bursts and pauses, making it difficult to reach line rate with very few streams. A test on UDP traffic shows that it's not possible to go beyond 134 Mbps / 12 kpps of outgoing traffic with 1500-bytes IP packets. Routed traffic tends to observe pauses as well if the traffic is bursty, making it even burstier after the wake-up. It seems that this feature was inherited from the original driver but nothing there mentions any reason for not using the interrupt instead, which the chip supports. Thus, this patch enables Tx interrupts and removes the timer. It does the two at once because it's not really possible to make the two mechanisms coexist, so a split patch doesn't make sense. First tests performed on a Mirabox (Armada 370) show that less CPU seems to be used when sending traffic. One reason might be that we now call the mvneta_tx_done_gbe() with a mask indicating which queues have been done instead of looping over all of them. The same UDP test above now happily reaches 987 Mbps / 87.7 kpps. Single-stream TCP traffic can now more easily reach line rate. HTTP transfers of 1 MB objects over a single connection went from 730 to 840 Mbps. It is even possible to go significantly higher (>900 Mbps) by tweaking tcp_tso_win_divisor. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Arnaud Ebalard <arno@natisbad.org> Cc: Eric Dumazet <eric.dumazet@gmail.com> Tested-by:
-
willy tarreau authored
Marvell has not published the chip's datasheet yet, so it's very hard to find the relevant bits to manipulate to change the IRQ behaviour. Fortunately, these bits are described in the proprietary LSP patch set which is publicly available here : http://www.plugcomputer.org/downloads/mirabox/ So let's put them back in the driver in order to reduce the burden of current and future maintenance. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by: -
willy tarreau authored
If a queue timeout is reported, we can oops because of some schedules while the caller is atomic, as shown below : mvneta d0070000.ethernet eth0: tx timeout BUG: scheduling while atomic: bash/1528/0x00000100 Modules linked in: slhttp_ethdiv(C) [last unloaded: slhttp_ethdiv] CPU: 2 PID: 1528 Comm: bash Tainted: G WC 3.13.0-rc4-mvebu-nf #180 [<c0011bd9>] (unwind_backtrace+0x1/0x98) from [<c000f1ab>] (show_stack+0xb/0xc) [<c000f1ab>] (show_stack+0xb/0xc) from [<c02ad323>] (dump_stack+0x4f/0x64) [<c02ad323>] (dump_stack+0x4f/0x64) from [<c02abe67>] (__schedule_bug+0x37/0x4c) [<c02abe67>] (__schedule_bug+0x37/0x4c) from [<c02ae261>] (__schedule+0x325/0x3ec) [<c02ae261>] (__schedule+0x325/0x3ec) from [<c02adb97>] (schedule_timeout+0xb7/0x118) [<c02adb97>] (schedule_timeout+0xb7/0x118) from [<c0020a67>] (msleep+0xf/0x14) [<c0020a67>] (msleep+0xf/0x14) from [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) from [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) from [<c024afc7>] (dev_watchdog+0x18b/0x1c4) [<c024afc7>] (dev_watchdog+0x18b/0x1c4) from [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) from [<c0020cad>] (run_timer_softirq+0x115/0x170) [<c0020cad>] (run_timer_softirq+0x115/0x170) from [<c001ccb9>] (__do_softirq+0xbd/0x1a8) [<c001ccb9>] (__do_softirq+0xbd/0x1a8) from [<c001cfad>] (irq_exit+0x61/0x98) [<c001cfad>] (irq_exit+0x61/0x98) from [<c000d4bf>] (handle_IRQ+0x27/0x60) [<c000d4bf>] (handle_IRQ+0x27/0x60) from [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) from [<c000fba9>] (__irq_usr+0x49/0x60) Ben Hutchings attempted to propose a better fix consisting in using a scheduled work for this, but while it fixed this panic, it caused other random freezes and panics proving that the reset sequence in the driver is unreliable and that additional fixes should be investigated. When sending multiple streams over a link limited to 100 Mbps, Tx timeouts happen from time to time, and the driver correctly recovers only when the function is disabled. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Ben Hutchings <ben@decadent.org.uk> Tested-by:
-
willy tarreau authored
Stats writers are mvneta_rx() and mvneta_tx(). They don't lock anything when they update the stats, and as a result, it randomly happens that the stats freeze on SMP if two updates happen during stats retrieval. This is very easily reproducible by starting two HTTP servers and binding each of them to a different CPU, then consulting /proc/net/dev in loops during transfers, the interface should immediately lock up. This issue also randomly happens upon link state changes during transfers, because the stats are collected in this situation, but it takes more attempts to reproduce it. The comments in netdevice.h suggest using per_cpu stats instead to get rid of this issue. This patch implements this. It merges both rx_stats and tx_stats into a single "stats" member with a single syncp. Both mvneta_rx() and mvneta_rx() now only update the a single CPU's counters. In turn, mvneta_get_stats64() does the summing by iterating over all CPUs to get their respective stats. With this change, stats are still correct and no more lockup is encountered. Note that this bug was present since the first import of the mvneta driver. It might make sense to backport it to some stable trees. If so, it depends on "d33dc73 net: mvneta: increase the 64-bit rx/tx stats out of the hot path". Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by:
-
willy tarreau authored
Better count packets and bytes in the stack and on 32 bit then accumulate them at the end for once. This saves two memory writes and two memory barriers per packet. The incoming packet rate was increased by 4.7% on the Openblocks AX3 thanks to this. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by:
-
Paul Gortmaker authored
None of these files are actually using any __init type directives and hence don't need to include <linux/init.h>. Most are just a left over from __devinit and __cpuinit removal, or simply due to code getting copied from one driver to the next. This covers everything under drivers/net except for wireless, which has been submitted separately. Signed-off-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nftablesDavid S. Miller authored
Pablo Neira Ayuso says: ==================== This small batch contains several Netfilter fixes for your net-next tree, more specifically: * Fix compilation warning in nft_ct in NF_CONNTRACK_MARK is not set, from Kristian Evensen. * Add dependency to IPV6 for NF_TABLES_INET. This one has been reported by the several robots that are testing .config combinations, from Paul Gortmaker. * Fix default base chain policy setting in nf_tables, from myself. ==================== Signed-off-by: -
Jiri Pirko authored
When ndo_neigh_setup is called, the bitfield used by NEIGH_VAR_SET is not initialized yet. This might cause confusion for the people who use NEIGH_VAR_SET in ndo_neigh_setup. So rather introduce NEIGH_VAR_INIT for usage in ndo_neigh_setup. Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
David S. Miller authored
Aaron Brown says: ==================== Intel Wired LAN Driver Updates This series contains several updates from Alex to ixgbe. To avoid head of line blocking in the event a VF stops cleaning Rx descriptors he makes sure QDE bits are set for a VF before the Rx queues are enabled. To avoid a situation where the head write-back registers can remain set ofter the driver is unloaded he clears them on a VF reset. Alexander Duyck (2): ixgbe: Force QDE via PFQDE for VFs during reset ixgbe: Clear head write-back registers on VF reset ==================== Signed-off-by: -
Alexander Duyck authored
The Tx head write-back registers are not cleared during an FLR or VF reset. As a result a configuration that had head write-back enabled can leave the registers set after the driver is unloaded. If the next driver loaded doesn't use the write-back registers this can lead to a bad configuration where head write-back is enabled, but the driver didn't request it. To avoid this situation the PF should be resetting the Tx head write-back registers when the VF requests a reset. Signed-off-by:
-
Alexander Duyck authored
This change makes it so that the QDE bits are set for a VF before the Rx queues are enabled. As such we avoid head of line blocking in the event that the VF stops cleaning Rx descriptors for whatever reason. Signed-off-by:
-
David S. Miller authored
Thomas Haller says: ==================== ipv6 addrconf: add IFA_F_NOPREFIXROUTE flag to suppress creation of IP6 routes v1 -> v2: add a second commit, handling NOPREFIXROUTE in ip6_del_addr. v2 -> v3: reword commit messages, code comments and some refactoring. v3 -> v4: refactor, rename variables, add enum v4 -> v5: rebase, so that patch applies cleanly to current net-next/master ==================== Signed-off-by:
-
