drivers/usb/host/xhci-mtk.c:256:1-3: WARNING: PTR_ERR_OR_ZERO can be used

 Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci

Fixes: b6bb72cf ("usb: xhci-mtk: add optional mcu and dma bus clocks")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Felipe writes:

usb: changes for v4.15 merge window

Not much going on this time around. With only 51 non-merge commits,
this was one of the smallest pull requests from the Gadget tree.

Most of the changes are in the mtu3 driver which added support for
36-bit DMA, support for USB 3.1 and support for dual-role (along with
some non-critical fixes).

The dwc2 driver got a few improvements to how we handle gadget state
tracking and also added support for STM32F7xx devices.

Other than that, we just some minor non-critical fixes and
improvements all over the place.

It has been noticed that the dwc2 udc state reporting doesn't
seem to work (at least on HiKey boards). Where after the initial
setup, the sysfs /sys/class/udc/f72c0000.usb/state file would
report "configured" no matter the state of the OTG port.

This patch adds a call so that we report to the UDC layer when
the gadget device is disconnected.

This patch does depend on the previous patch ("usb: dwc2:
Improve gadget state disconnection handling") in this patch set
in order to properly work.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We've found that while in host mode, using Android, if one runs
the command:
  stop adbd

The existing usb devices being utilized in host mode are disconnected.
This is most visible with usb networking devices.

This seems to be due to adbd closing the file:
  /dev/usb-ffs/adb/ep0
Which calls ffs_ep0_release() and the following backtrace:

[<ffffff800875a430>] dwc2_hsotg_ep_disable+0x148/0x150
[<ffffff800875a498>] dwc2_hsotg_udc_stop+0x60/0x110
[<ffffff8008787950>] usb_gadget_remove_driver+0x58/0x78
[<ffffff80087879e4>] usb_gadget_unregister_driver+0x74/0xe8
[<ffffff80087850c0>] unregister_gadget+0x28/0x58
[<ffffff800878511c>] unregister_gadget_item+0x2c/0x40
[<ffffff8008790ea8>] ffs_data_clear+0xe8/0xf8
[<ffffff8008790ed8>] ffs_data_reset+0x20/0x58
[<ffffff8008793218>] ffs_data_closed+0x98/0xe8
[<ffffff80087932d8>] ffs_ep0_release+0x20/0x30

Then when dwc2_hsotg_ep_disable() is called, we call
kill_all_requests() which causes a bunch of the following
messages:

dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
init: Service 'adbd' (pid 1915) killed by signal 9
init: Sending signal 9 to service 'adbd' (pid 1915) process group...
init: Successfully killed process cgroup uid 0 pid 1915 in 0ms
init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:15)
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 8 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 12 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 15 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 3 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_update_urb_state_abn(): trimming xfer length

And the usb devices connected are basically hung at this point.

It seems like if we're in host mode, we probably shouldn't run
the dwc2_hostg_ep_disable logic, so this patch returns an error
in that case.

With this patch (along with the previous patch in this set), we avoid
the mismatched interrupts and connected usb devices continue to function.

I'm not sure if some other solution would be better here, but this seems
to work, so I wanted to send it out for input on what the right approach
should be.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Reported-by: YongQin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In the earlier commit dad3f793 ("usb: dwc2: Make sure we
disconnect the gadget state"), I was trying to fix up the
fact that we somehow weren't disconnecting the gadget state,
so that when the OTG port was plugged in the second time we
would get warnings about the state tracking being wrong.

(This seems to be due to a quirk of the HiKey board where
we do not ever get any otg interrupts, particularly the session
end detected signal. Instead we only see status change
interrupt.)

The fix there was somewhat simple, as it just made sure to
call dwc2_hsotg_disconnect() before we connected things up
in OTG mode, ensuring the state handling didn't throw errors.

But in looking at a different issue I was seeing with UDC
state handling, I realized that it would be much better
to call dwc2_hsotg_disconnect when we get the state change
signal moving to host mode.

Thus, this patch removes the earlier disconnect call I added
and moves it (and the needed locking) to the host mode
transition.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Driver currently notifies only USB2 PHY on USB mode change.
Extend this to USB3 PHY so that PHY drivers based on the
mode can release system resources - clocks, regulators etc.
Additionally Qualcomm QMP and QUSB2 PHY drivers need to
override VBUS signal in PHY wrapper in device mode as USB
VBUS line is not connected to PHYs. Also, remove NULL checks
for PHY when calling phy_set_mode as PHY ops already check this.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Driver currently resumes and increments pm usage_count
of its child device (dwc3 main) from its runtime_resume
handler. This requires dwc3 runtime_resume to perform
pm_runtime_put to decrement the pm usage_count. However
runtime_put from dwc3 happens for non pci drivers
(e.g. dwc3-if-simple.c) as well which results in dwc3
pm usage_count becoming negative after couple of
runtime suspend resume iterations. Fix this by
performing runtime_get/put from dwc3-pci driver only
using workqueue.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Driver powers-off PHYs and reinitializes DWC3 core and gadget on
resume. While this works fine for gadget mode but in host
mode there is not re-initialization of host stack. Also, resetting
bus as part of bus_suspend/resume is not correct which could affect
(or disconnect) connected devices.
Fix this by not reinitializing core on suspend/resume in host mode
for HOST only and OTG/drd configurations.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If devm_extcon_dev_allocate() fails, we should disable clk before return.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 860d2686 ("usb: phy: tahvo: Use devm_extcon_dev_[allocate|register]() and replace deprecated API")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1350962
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1222118
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 703128
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 145713
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull staging and IIO fixes from Greg KH:
 "Here are a small number of patches to resolve some reported IIO and a
  staging driver problem. Nothing major here, full details are in the
  shortlog below.

  All have been in linux-next with no reported issues"

* tag 'staging-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: bcm2835-audio: Fix memory corruption
  iio: adc: at91-sama5d2_adc: fix probe error on missing trigger property
  iio: adc: dln2-adc: fix build error
  iio: dummy: events: Add missing break
  staging: iio: ade7759: fix signed extension bug on shift of a u8
  iio: pressure: zpa2326: Remove always-true check which confuses gcc
  iio: proximity: as3935: noise detection + threshold changes

Pull char/misc driver fixes from Greg KH:
 "Here are four small fixes for 4.14-rc6.

  Three of them are binder driver fixes for reported issues, and the
  last one is a hyperv driver bugfix. Nothing major, but good fixes to
  get into 4.14-final.

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  android: binder: Fix null ptr dereference in debug msg
  android: binder: Don't get mm from task
  vmbus: hvsock: add proper sync for vmbus_hvsock_device_unregister()
  binder: call poll_wait() unconditionally.

Pull USB/PHY fixes from Greg KH:
 "Here are a small number of USB and PHY driver fixes for 4.14-rc6

  There is the usual musb and xhci fixes in here, as well as some needed
  phy patches. Also is a nasty regression fix for usbfs that has started
  to hit a lot of people using virtual machines.

  All of these have been in linux-next with no reported problems"

* tag 'usb-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
  usb: hub: Allow reset retry for USB2 devices on connect bounce
  USB: core: fix out-of-bounds access bug in usb_get_bos_descriptor()
  MAINTAINERS: fix git tree url for musb module
  usb: quirks: add quirk for WORLDE MINI MIDI keyboard
  usb: musb: sunxi: Explicitly release USB PHY on exit
  usb: musb: Check for host-mode using is_host_active() on reset interrupt
  usb: musb: musb_cppi41: Configure the number of channels for DA8xx
  usb: musb: musb_cppi41: Fix cppi41_set_dma_mode() for DA8xx
  usb: musb: musb_cppi41: Fix the address of teardown and autoreq registers
  USB: musb: fix late external abort on suspend
  USB: musb: fix session-bit runtime-PM quirk
  usb: cdc_acm: Add quirk for Elatec TWN3
  USB: devio: Revert "USB: devio: Don't corrupt user memory"
  usb: xhci: Handle error condition in xhci_stop_device()
  usb: xhci: Reset halted endpoint if trb is noop
  xhci: Cleanup current_cmd in xhci_cleanup_command_queue()
  xhci: Identify USB 3.1 capable hosts by their port protocol capability
  USB: serial: metro-usb: add MS7820 device id
  phy: rockchip-typec: Check for errors from tcphy_phy_init()
  phy: rockchip-typec: Don't set the aux voltage swing to 400 mV
  ...

When going into S3 suspend, the Acer TravelMate P648-M and P648-G3
laptops immediately wake up 3-4 seconds later for no obvious reason.

Unbinding the integrated Huawei 4G LTE modem before suspend avoids
the issue, even though we are not using the modem at all (checked
from rescue.target/runlevel1). The problem also occurs when the option
and cdc-ether modem drivers aren't loaded; it reproduces just with the
base usb driver. Under Windows the system can suspend fine.

Seeking a better fix, we've tried a lot of things, including:
 - Check that the device's power/wakeup is disabled
 - Check that remote wakeup is off at the USB level
 - All the quirks in drivers/usb/core/quirks.c e.g. USB_QUIRK_RESET_RESUME,
   USB_QUIRK_RESET, USB_QUIRK_IGNORE_REMOTE_WAKEUP, USB_QUIRK_NO_LPM.

but none of that makes any difference.

There are no errors in the logs showing any suspend/resume-related issues.
When the system wakes up due to the modem, log-wise it appears to be a
normal resume.

Introduce a quirk to disable the port during suspend when the modem is
detected.

The modem from the P648-G3 model is:
T:  Bus=01 Lev=01 Prnt=01 Port=08 Cnt=04 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=12d1 ProdID=15c3 Rev= 1.02
S:  Manufacturer=Huawei Technologies Co., Ltd.
S:  Product=HUAWEI Mobile
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=  2mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=
E:  Ad=82(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver=
E:  Ad=86(I) Atr=03(Int.) MxPS=  16 Ivl=2ms
I:  If#= 3 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=16 Driver=
E:  Ad=86(I) Atr=03(Int.) MxPS=  16 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
C:* #Ifs= 6 Cfg#= 2 Atr=a0 MxPwr=  2mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=2ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
C:  #Ifs= 2 Cfg#= 3 Atr=a0 MxPwr=  2mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=2ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Based on an earlier patch by Chris Chiu.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove dummy clocks for usb wakeup and add optional ones for
MCU_BUS_CK and DMA_BUS_CK.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a new optional property to disable u3ports
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Due to all MediaTek SoCs with xHCI host controller use this
driver, remove limitation for specific SoCs
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There are mcu_bus and dma_bus clocks needed to be controlled by
driver on some SoCs, so add them as optional ones
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The wakeup debounce clocks for each ports in fact are not
needed, so remove them.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support to disable specific usb3 ports, it's useful when
usb3 phy is shared with PCIe or SATA, because we should disable
the corresponding usb3 port if the phy is used by PCIe or SATA.
Sometimes it's helpful to analyse and solve problems.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is useful to find out the root cause when the Super Speed doesn't
work. Such as when the T-PHY is switched to PCIe or SATA, and affects
Super Speed function, the check will fail.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make use of ports count from xhci but not from ippc in
xhci_mtk_sch_init()
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch uses the simpler dma_set_mask_and_coherent() instead of
doing these as separate steps
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull input fix from Dmitry Torokhov:
 "A fix for a broken commit in the previous pull breaking automatic
  module loading of input handlers, such ad evdev"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: do not use property bits when generating module alias

The commit 8724ecb0 ("Input: allow matching device IDs on property
bits") started using property bits when generating module aliases for input
handlers, but did not adjust the generation of MODALIAS attribute on input
device uevents, breaking automatic module loading. Given that no handler
currently uses property bits in their module tables, let's revert this part
of the commit for now.
Reported-by: Damien Wyart <damien.wyart@gmail.com>
Tested-by: Damien Wyart <damien.wyart@gmail.com>
Fixes: 8724ecb0 ("Input: allow matching device IDs on property bits")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull x86 fixes from Thomas Gleixner:
 "A couple of fixes addressing the following issues:

   - The last polishing for the TLB code, removing the last BUG_ON() and
     the debug file along with tidying up the lazy TLB code.

   - Prevent triple fault on 1st Gen. 486 caused by stupidly calling the
     early IDT setup after the first function which causes a fault which
     should be caught by the exception table.

   - Limit the mmap of /dev/mem to valid addresses

   - Prevent late microcode loading on Broadwell X

   - Remove a redundant assignment in the cache info code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Limit mmap() of /dev/mem to valid physical addresses
  x86/mm: Remove debug/x86/tlb_defer_switch_to_init_mm
  x86/mm: Tidy up "x86/mm: Flush more aggressively in lazy TLB mode"
  x86/mm/64: Remove the last VM_BUG_ON() from the TLB code
  x86/microcode/intel: Disable late loading on model 79
  x86/idt: Initialize early IDT before cr4_init_shadow()
  x86/cpu/intel_cacheinfo: Remove redundant assignment to 'this_leaf'

Pull timer fix from Thomas Gleixner:
 "A single fix to make the cs5535 clock event driver robust agaist
  spurious interrupts"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clockevents/drivers/cs5535: Improve resilience to spurious interrupts

Pull smp/hotplug fix from Thomas Gleixner:
 "The recent rework of the callback invocation missed to cleanup the
  leftovers of the operation, so under certain circumstances a
  subsequent CPU hotplug operation accesses stale data and crashes.
  Clean it up."

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Reset node state after operation

Pull perf fixes from Thomas Gleixner:
 "A series of fixes for perf tooling:

   - Make xyarray return the X/Y size correctly which fixes a crash in
     the exit code.

   - Fix the libc path in test so it works not only on Debian/Ubuntu
     correctly

   - Check for eBPF file existance and output a useful error message
     instead of failing to compile a non existant file

   - Make sure perf_hpp_fmt is not longer references before freeing it

   - Use list_del_init() in the histogram code to prevent a crash when
     the already deleted element is deleted again

   - Remove the leftovers of the removed '-l' option

   - Add reviewer entries to the MAINTAINERS file"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf test shell trace+probe_libc_inet_pton.sh: Be compatible with Debian/Ubuntu
  perf xyarray: Fix wrong processing when closing evsel fd
  perf buildid-list: Fix crash when processing PERF_RECORD_NAMESPACE
  perf record: Fix documentation for a inexistent option '-l'
  perf tools: Add long time reviewers to MAINTAINERS
  perf tools: Check wether the eBPF file exists in event parsing
  perf hists: Add extra integrity checks to fmt_free()
  perf hists: Fix crash in perf_hpp__reset_output_field()

Pull irq fixes from Thomas Gleixner:
 "A set of small fixes mostly in the irq drivers area:

   - Make the tango irq chip work correctly, which requires a new
     function in the generiq irq chip implementation

   - A set of updates to the GIC-V3 ITS driver removing a bogus BUG_ON()
     and parsing the VCPU table size correctly"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: generic chip: remove irq_gc_mask_disable_reg_and_ack()
  irqchip/tango: Use irq_gc_mask_disable_and_ack_set
  genirq: generic chip: Add irq_gc_mask_disable_and_ack_set()
  irqchip/gic-v3-its: Add missing changes to support 52bit physical address
  irqchip/gic-v3-its: Fix the incorrect parsing of VCPU table size
  irqchip/gic-v3-its: Fix the incorrect BUG_ON in its_init_vpe_domain()
  DT: arm,gic-v3: Update the ITS size in the examples

Pull objtool fix from Thomas Gleixner:
 "Plug a memory leak in the instruction decoder"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix memory leak in decode_instructions()

Pull networking fixes from David Miller:
 "A little more than usual this time around. Been travelling, so that is
  part of it.

  Anyways, here are the highlights:

   1) Deal with memcontrol races wrt. listener dismantle, from Eric
      Dumazet.

   2) Handle page allocation failures properly in nfp driver, from Jaku
      Kicinski.

   3) Fix memory leaks in macsec, from Sabrina Dubroca.

   4) Fix crashes in pppol2tp_session_ioctl(), from Guillaume Nault.

   5) Several fixes in bnxt_en driver, including preventing potential
      NVRAM parameter corruption from Michael Chan.

   6) Fix for KRACK attacks in wireless, from Johannes Berg.

   7) rtnetlink event generation fixes from Xin Long.

   8) Deadlock in mlxsw driver, from Ido Schimmel.

   9) Disallow arithmetic operations on context pointers in bpf, from
      Jakub Kicinski.

  10) Missing sock_owned_by_user() check in sctp_icmp_redirect(), from
      Xin Long.

  11) Only TCP is supported for sockmap, make that explicit with a
      check, from John Fastabend.

  12) Fix IP options state races in DCCP and TCP, from Eric Dumazet.

  13) Fix panic in packet_getsockopt(), also from Eric Dumazet.

  14) Add missing locked in hv_sock layer, from Dexuan Cui.

  15) Various aquantia bug fixes, including several statistics handling
      cures. From Igor Russkikh et al.

  16) Fix arithmetic overflow in devmap code, from John Fastabend.

  17) Fix busted socket memory accounting when we get a fault in the tcp
      zero copy paths. From Willem de Bruijn.

  18) Don't leave opt->tot_len uninitialized in ipv6, from Eric Dumazet"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
  stmmac: Don't access tx_q->dirty_tx before netif_tx_lock
  ipv6: flowlabel: do not leave opt->tot_len with garbage
  of_mdio: Fix broken PHY IRQ in case of probe deferral
  textsearch: fix typos in library helpers
  rxrpc: Don't release call mutex on error pointer
  net: stmmac: Prevent infinite loop in get_rx_timestamp_status()
  net: stmmac: Fix stmmac_get_rx_hwtstamp()
  net: stmmac: Add missing call to dev_kfree_skb()
  mlxsw: spectrum_router: Configure TIGCR on init
  mlxsw: reg: Add Tunneling IPinIP General Configuration Register
  net: ethtool: remove error check for legacy setting transceiver type
  soreuseport: fix initialization race
  net: bridge: fix returning of vlan range op errors
  sock: correct sk_wmem_queued accounting on efault in tcp zerocopy
  bpf: add test cases to bpf selftests to cover all access tests
  bpf: fix pattern matches for direct packet access
  bpf: fix off by one for range markings with L{T, E} patterns
  bpf: devmap fix arithmetic overflow in bitmap_size calculation
  net: aquantia: Bad udp rate on default interrupt coalescing
  net: aquantia: Enable coalescing management via ethtool interface
  ...

This is the possible reason for different hard to reproduce
problems on my ARMv7-SMP test system.

The symptoms are in recent kernels imprecise external aborts,
and in older kernels various kinds of network stalls and
unexpected page allocation failures.

My testing indicates that the trouble started between v4.5 and v4.6
and prevails up to v4.14.

Using the dirty_tx before acquiring the spin lock is clearly
wrong and was first introduced with v4.6.

Fixes: e3ad57c9 ("stmmac: review RX/TX ring management")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When syzkaller team brought us a C repro for the crash [1] that
had been reported many times in the past, I finally could find
the root cause.

If FlowLabel info is merged by fl6_merge_options(), we leave
part of the opt_space storage provided by udp/raw/l2tp with random value
in opt_space.tot_len, unless a control message was provided at sendmsg()
time.

Then ip6_setup_cork() would use this random value to perform a kzalloc()
call. Undefined behavior and crashes.

Fix is to properly set tot_len in fl6_merge_options()

At the same time, we can also avoid consuming memory and cpu cycles
to clear it, if every option is copied via a kmemdup(). This is the
change in ip6_setup_cork().

[1]
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
   (ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 6613 Comm: syz-executor0 Not tainted 4.14.0-rc4+ #127
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801cb64a100 task.stack: ffff8801cc350000
RIP: 0010:ip6_setup_cork+0x274/0x15c0 net/ipv6/ip6_output.c:1168
RSP: 0018:ffff8801cc357550 EFLAGS: 00010203
RAX: dffffc0000000000 RBX: ffff8801cc357748 RCX: 0000000000000010
RDX: 0000000000000002 RSI: ffffffff842bd1d9 RDI: 0000000000000014
RBP: ffff8801cc357620 R08: ffff8801cb17f380 R09: ffff8801cc357b10
R10: ffff8801cb64a100 R11: 0000000000000000 R12: ffff8801cc357ab0
R13: ffff8801cc357b10 R14: 0000000000000000 R15: ffff8801c3bbf0c0
FS:  00007f9c5c459700(0000) GS:ffff8801db200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020324000 CR3: 00000001d1cf2000 CR4: 00000000001406f0
DR0: 0000000020001010 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000600
Call Trace:
 ip6_make_skb+0x282/0x530 net/ipv6/ip6_output.c:1729
 udpv6_sendmsg+0x2769/0x3380 net/ipv6/udp.c:1340
 inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:762
 sock_sendmsg_nosec net/socket.c:633 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:643
 SYSC_sendto+0x358/0x5a0 net/socket.c:1750
 SyS_sendto+0x40/0x50 net/socket.c:1718
 entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x4520a9
RSP: 002b:00007f9c5c458c08 EFLAGS: 00000216 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000000000718000 RCX: 00000000004520a9
RDX: 0000000000000001 RSI: 0000000020fd1000 RDI: 0000000000000016
RBP: 0000000000000086 R08: 0000000020e0afe4 R09: 000000000000001c
R10: 0000000000000000 R11: 0000000000000216 R12: 00000000004bb1ee
R13: 00000000ffffffff R14: 0000000000000016 R15: 0000000000000029
Code: e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 ea 0f 00 00 48 8d 79 04 48 b8 00 00 00 00 00 fc ff df 45 8b 74 24 04 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85
RIP: ip6_setup_cork+0x274/0x15c0 net/ipv6/ip6_output.c:1168 RSP: ffff8801cc357550
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>