This patch fixes the following
1. When interface is being teardown and queues are being cleaned up,
   free pending SKBs that are in SQ which are either not transmitted
   or freed as NAPI is disabled by that time.
2. While interface initialization, delay CFG_DONE notification till
   the end to avoid corner cases where TXQs are enabled but CQ
   interrupts are not which results blocking transmission and kicking
   off watchdog.
3. Check for IFF_UP while re-enabling RBDR interrupts from tasklet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes multiple issues
1. Convert all driver statistics to percpu counters for accuracy.
2. To avoid multiple CQEs posted by a TSO packet appended to HW,
   TSO pkt's SQE has 'post_cqe' not set but a dummy SQE is added
   for getting HW transmit completion notification. This dummy
   SQE has 'dont_send' set and HW drops the pkt pointed to in this
   thus Tx drop counter increases. This patch fixes this by subtracting
   SW tx tso counter from HW Tx drop counter for actual packet drop counter.
3. Reset all individual queue's and VNIC HW stats when interface is going down.
4. Getrid off unnecessary counters in hot path.
5. Bringout all CQE error stats i.e both Rx and Tx.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes enabling of HW verification of L3/L4 length and
TCP/UDP checksum which is currently being cleared. Also fixed VLAN
stripping config which is being cleared when multiqset is enabled.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Programming LMAC credits taking 9K frame size by default is incorrect
as for an interface which is one of the many on the same BGX/QLM
no of credits available will be less as Tx FIFO will be divided
across all interfaces. So let's say a BGX with 40G interface and another
BGX with multiple 10G, bandwidth of 10G interfaces will be effected when
traffic is running on both 40G and 10G interfaces simultaneously.

This patch fixes this issue by programming credits based on netdev's MTU.
Also fixed configuring MTU to HW and added CQE counter for pkts which
exceed this value.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the 'bgx_id' determination on 83xx where there are
4 BGX blocks instead of 2 on other platforms.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
ipv4: Fix memory leaks and reference issues in fib

This series fixes one major issue and one minor issue in the fib tables.

The major issue is that we had lost the functionality that was flushing the
local table entries from main after we had unmerged the two tries.  In
order to regain the functionality I have performed a partial revert and
then moved the functionality for flushing the external entries from main
into fib_unmerge.

The minor issue was a memory leak that could occur in the event that we
weren't able to add an alias to the local trie resulting in the fib alias
being leaked.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a small memory leak that can occur where we leak a fib_alias in the
event of us not being able to insert it into the local table.

Fixes: 0ddcf43d ("ipv4: FIB Local/MAIN table collapse")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch that removed the FIB offload infrastructure was a bit too
aggressive and also removed code needed to clean up us splitting the table
if additional rules were added.  Specifically the function
fib_trie_flush_external was called at the end of a new rule being added to
flush the foreign trie entries from the main trie.

I updated the code so that we only call fib_trie_flush_external on the main
table so that we flush the entries for local from main.  This way we don't
call it for every rule change which is what was happening previously.

Fixes: 347e3b28 ("switchdev: remove FIB offload infrastructure")
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I made some invalid assumptions with BPF_AND and BPF_MOD that could result in
invalid accesses to bpf map entries.  Fix this up by doing a few things

1) Kill BPF_MOD support.  This doesn't actually get used by the compiler in real
life and just adds extra complexity.

2) Fix the logic for BPF_AND, don't allow AND of negative numbers and set the
minimum value to 0 for positive AND's.

3) Don't do operations on the ranges if they are set to the limits, as they are
by definition undefined, and allowing arithmetic operations on those values
could make them appear valid when they really aren't.

This fixes the testcase provided by Jann as well as a few other theoretical
problems.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl_xdp_size() only considers the size of the actual payload attribute,
and misses the space taken by the attribute used for nesting (IFLA_XDP).

Fixes: d1fdd913 ("rtnl: add option for setting link xdp prog")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The size reported by rtnl_vfinfo_size doesn't match the space used by
rtnl_fill_vfinfo.

rtnl_vfinfo_size currently doesn't account for the nest attributes
used by statistics (added in commit 3b766cd8), nor for struct
ifla_vf_tx_rate (since commit ed616689, which added ifla_vf_rate
to the dump without removing ifla_vf_tx_rate, but replaced
ifla_vf_tx_rate with ifla_vf_rate in the size computation).

Fixes: 3b766cd8 ("net/core: Add reading VF statistics through the PF netdevice")
Fixes: ed616689 ("net-next:v4: Add support to configure SR-IOV VF minimum and maximum Tx rate through ip tool")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rolf Neugebauer reported very long delays at netns dismantle.

Eric W. Biederman was kind enough to look at this problem
and noticed synchronize_net() occurring from netif_napi_del() that was
added in linux-4.5

Busy polling makes no sense for tunnels NAPI.
If busy poll is used for sessions over tunnels, the poller will need to
poll the physical device queue anyway.

netif_tx_napi_add() could be used here, but function name is misleading,
and renaming it is not stable material, so set NAPI_STATE_NO_BUSY_POLL
bit directly.

This will avoid inserting gro_cells napi structures in napi_hash[]
and avoid the problematic synchronize_net() (per possible cpu) that
Rolf reported.

Fixes: 93d05d4a ("net: provide generic busy polling to all NAPI drivers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Honor udptable parameter that is passed to __udp*_lib_mcast_deliver(),
otherwise udplite broadcast/multicast use the wrong table and it breaks.

Fixes: 2dc41cff ("udp: Use hash2 for long hash1 chains in __udp*_lib_mcast_deliver.")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch disable capturing multicast packets when multicast mode
disabled for ethernet ('ifconfig eth0 -multicast'). In that case
no multicast packet will be passed to kernel.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Multicast support was implemented by commit 775dd682
('arc_emac: implement promiscuous mode and multicast filtering').

It can be enabled explicity using 'ifconfig eth0 multicast'.
The patch is needed in order to remove explicit configuration
as most devices has multicast mode enabled by default.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Giuseppe Cavallaro says:

====================
stmmac: fix PTP support

This subset of patches aim to fix the PTP support
for the stmmac and especially for 4.x chip series.
While setting PTP on an ST box with 4.00a Ethernet
core, the kernel panics due to a broken settings
of the descriptors. The patches review the
register configuration, the algo used for configuring
the protocol, the way to get the timestamp inside
the RX/TX descriptors and, in the end, the statistics
displayed by ethtool.

V2: RESEND all the patches adding the Acked-by.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the ethtool stats for PTP frames; previous
version does not take care about some message types: i.e.
announce, management and signaling. It also provided a
broken statistic in case of "No PTP message received".
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to bad management of the descriptors, when use ptp4l,
kernel panics as shown below:
-----------------------------------------------------------
 Unable to handle kernel NULL pointer dereference at virtual
 address 000001ac
 ...
 Internal error: Oops: 17 [#1] SMP ARM
 ...
 Hardware name: STi SoC with Flattened Device Tree
 task: c0c05e80 task.stack: c0c00000
 PC is at dwmac4_wrback_get_tx_timestamp_status+0x0/0xc
 LR is at stmmac_tx_clean+0x2f8/0x4d4
-----------------------------------------------------------

In case of GMAC4 the extended descriptor pointers were
used for getting the timestamp. These are NULL for this HW,
and the normal ones must be used.

The PTP also had problems on this chip due to the bad
register management and issues on the algo adopted to
setup the PTP and getting the timestamp values from the
descriptors.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to update this file by using BIT macros, removing
not used defines and fixes some typos.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 24cf3af3 ("igmp: call ip_mc_clear_src..."), we forgot to remove
igmpv3_clear_delrec() in ip_mc_down(), which also called ip_mc_clear_src().
This make us clear all IGMPv3 source filter info after NETDEV_DOWN.
Move igmpv3_clear_delrec() to ip_mc_destroy_dev() and then no need
ip_mc_clear_src() in ip_mc_destroy_dev().

On the other hand, we should restore back instead of free all source filter
info in igmpv3_del_delrec(). Or we will not able to restore IGMPv3 source
filter info after NETDEV_UP and NETDEV_POST_TYPE_CHANGE.

Fixes: 24cf3af3 ("igmp: call ip_mc_clear_src() only when ...")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TSE PCS SGMII ethernet has an issue where switching speed doesn't work
caused by a faulty register macro offset. This fixes the issue.
Signed-off-by: Jia Jie Ho <ho.jia.jie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix off by one wrt. indexing when dumping /proc/net/route entries,
    from Alexander Duyck.

 2) Fix lockdep splats in iwlwifi, from Johannes Berg.

 3) Cure panic when inserting certain netfilter rules when NFT_SET_HASH
    is disabled, from Liping Zhang.

 4) Memory leak when nft_expr_clone() fails, also from Liping Zhang.

 5) Disable UFO when path will apply IPSEC tranformations, from Jakub
    Sitnicki.

 6) Don't bogusly double cwnd in dctcp module, from Florian Westphal.

 7) skb_checksum_help() should never actually use the value "0" for the
    resulting checksum, that has a special meaning, use CSUM_MANGLED_0
    instead. From Eric Dumazet.

 8) Per-tx/rx queue statistic strings are wrong in qed driver, fix from
    Yuval MIntz.

 9) Fix SCTP reference counting of associations and transports in
    sctp_diag. From Xin Long.

10) When we hit ip6tunnel_xmit() we could have come from an ipv4 path in
    a previous layer or similar, so explicitly clear the ipv6 control
    block in the skb. From Eli Cooper.

11) Fix bogus sleeping inside of inet_wait_for_connect(), from WANG
    Cong.

12) Correct deivce ID of T6 adapter in cxgb4 driver, from Hariprasad
    Shenai.

13) Fix potential access past the end of the skb page frag array in
    tcp_sendmsg(). From Eric Dumazet.

14) 'skb' can legitimately be NULL in inet{,6}_exact_dif_match(). Fix
    from David Ahern.

15) Don't return an error in tcp_sendmsg() if we wronte any bytes
    successfully, from Eric Dumazet.

16) Extraneous unlocks in netlink_diag_dump(), we removed the locking
    but forgot to purge these unlock calls. From Eric Dumazet.

17) Fix memory leak in error path of __genl_register_family(). We leak
    the attrbuf, from WANG Cong.

18) cgroupstats netlink policy table is mis-sized, from WANG Cong.

19) Several XDP bug fixes in mlx5, from Saeed Mahameed.

20) Fix several device refcount leaks in network drivers, from Johan
    Hovold.

21) icmp6_send() should use skb dst device not skb->dev to determine L3
    routing domain. From David Ahern.

22) ip_vs_genl_family sets maxattr incorrectly, from WANG Cong.

23) We leak new macvlan port in some cases of maclan_common_netlink()
    errors. Fix from Gao Feng.

24) Similar to the icmp6_send() fix, icmp_route_lookup() should
    determine L3 routing domain using skb_dst(skb)->dev not skb->dev.
    Also from David Ahern.

25) Several fixes for route offloading and FIB notification handling in
    mlxsw driver, from Jiri Pirko.

26) Properly cap __skb_flow_dissect()'s return value, from Eric Dumazet.

27) Fix long standing regression in ipv4 redirect handling, wrt.
    validating the new neighbour's reachability. From Stephen Suryaputra
    Lin.

28) If sk_filter() trims the packet excessively, handle it reasonably in
    tcp input instead of exploding. From Eric Dumazet.

29) Fix handling of napi hash state when copying channels in sfc driver,
    from Bert Kenward.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (121 commits)
  mlxsw: spectrum_router: Flush FIB tables during fini
  net: stmmac: Fix lack of link transition for fixed PHYs
  sctp: change sk state only when it has assocs in sctp_shutdown
  bnx2: Wait for in-flight DMA to complete at probe stage
  Revert "bnx2: Reset device during driver initialization"
  ps3_gelic: fix spelling mistake in debug message
  net: ethernet: ixp4xx_eth: fix spelling mistake in debug message
  ibmvnic: Fix size of debugfs name buffer
  ibmvnic: Unmap ibmvnic_statistics structure
  sfc: clear napi_hash state when copying channels
  mlxsw: spectrum_router: Correctly dump neighbour activity
  mlxsw: spectrum: Fix refcount bug on span entries
  bnxt_en: Fix VF virtual link state.
  bnxt_en: Fix ring arithmetic in bnxt_setup_tc().
  Revert "include/uapi/linux/atm_zatm.h: include linux/time.h"
  tcp: take care of truncations done by sk_filter()
  ipv4: use new_gw for redirect neigh lookup
  r8152: Fix error path in open function
  net: bpqether.h: remove if_ether.h guard
  net: __skb_flow_dissect() must cap its return value
  ...

Pull arch/tile bugfix from Chris Metcalf:
 "This just fixes an incompatibility with tile __ro_after_init"

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: handle __ro_after_init like parisc does

Pull RTC fixes from Alexandre Belloni:
 "Here are a few driver fixes for 4.9. It has been calm for a while so I
  don't expect more for this cycle.

  Drivers:
   - asm9260: fix module autoload
   - cmos: fix crashes
   - omap: fix clock handling"

* tag 'rtc-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  rtc: omap: prevent disabling of clock/module during suspend
  rtc: omap: Fix selecting external osc
  rtc: cmos: Don't enable interrupts in the middle of the interrupt handler
  rtc: cmos: remove all __exit_p annotations
  rtc: asm9260: fix module autoload

The tile architecture already marks RO_DATA as read-only in
the kernel, so grouping RO_AFTER_INIT_DATA with RO_DATA, as is
done by default, means the kernel faults in init when it tries
to write to RO_AFTER_INIT_DATA.  For now, just arrange that
__ro_after_init is handled like __write_once, i.e. __read_mostly.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>

Since commit b45f64d1 ("mlxsw: spectrum_router: Use FIB notifications
instead of switchdev calls") we reflect to the device the entire FIB
table and not only FIBs that point to netdevs created by the driver.

During module removal, FIBs of the second type are removed following
NETDEV_UNREGISTER events sent. The other FIBs are still present in both
the driver's cache and the device's table.

Fix this by iterating over all the FIB tables in the device and flush
them. There's no need to take locks, as we're the only writer.

Fixes: b45f64d1 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 52f95bbf ("stmmac: fix adjust link call in case of a switch
is attached") added some logic to avoid polling the fixed PHY and
therefore invoking the adjust_link callback more than once, since this
is a fixed PHY and link events won't be generated.

This works fine the first time, because we start with phydev->irq =
PHY_POLL, so we call adjust_link, then we set phydev->irq =
PHY_IGNORE_INTERRUPT and we stop polling the PHY.

Now, if we called ndo_close(), which calls both phy_stop() and does an
explicit netif_carrier_off(), we end up with a link down. Upon calling
ndo_open() again, despite starting the PHY state machine, we have
PHY_IGNORE_INTERRUPT set, and we generate no link event at all, so the
link is permanently down.

Fixes: 52f95bbf ("stmmac: fix adjust link call in case of a switch is attached")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now when users shutdown a sock with SEND_SHUTDOWN in sctp, even if
this sock has no connection (assoc), sk state would be changed to
SCTP_SS_CLOSING, which is not as we expect.

Besides, after that if users try to listen on this sock, kernel
could even panic when it dereference sctp_sk(sk)->bind_hash in
sctp_inet_listen, as bind_hash is null when sock has no assoc.

This patch is to move sk state change after checking sk assocs
is not empty, and also merge these two if() conditions and reduce
indent level.

Fixes: d46e416c ("sctp: sctp should change socket state when shutdown is received")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Baoquan He says:

====================
bnx2: Wait for in-flight DMA to complete at probe stage

This is v2 post.

In commit 3e1be7ad ("bnx2: Reset device during driver initialization"),
firmware requesting code was moved from open stage to probe stage.
The reason is in kdump kernel hardware iommu need device be reset in
driver probe stage, otherwise those in-flight DMA from 1st kernel
will continue going and look up into the newly created io-page tables.
However bnx2 chip resetting involves firmware requesting issue, that
need be done in open stage.

Michale Chan suggested we can just wait for the old in-flight DMA to
complete at probe stage, then though without device resetting, we
don't need to worry the old in-flight DMA could continue looking up
the newly created io-page tables.

v1->v2:
    Michael suggested to wait for the in-flight DMA to complete at probe
    stage. So give up the old method of trying to reset chip at probe
    stage, take the new way accordingly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In-flight DMA from 1st kernel could continue going in kdump kernel.
New io-page table has been created before bnx2 does reset at open stage.
We have to wait for the in-flight DMA to complete to avoid it look up
into the newly created io-page table at probe stage.
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 3e1be7ad.

When people build bnx2 driver into kernel, it will fail to detect
and load firmware because firmware is contained in initramfs and
initramfs has not been uncompressed yet during do_initcalls. So
revert commit 3e1be7ad and work out a new way in the later patch.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake "unmached" to "unmatched" in
debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 022d00ee ("ASoC: lpass-platform: Fix broken pcm data
usage") the stream specific information initialization was broken, with
the dma channel information not being initialized if there was no
alloc_dma_channel() helper function.

Before that, the DMA channel number was implicitly initialized to zero
because the backing store was allocated with devm_kzalloc().  When the
init code was rewritten, that implicit initialization was lost, and gcc
rightfully complains about an uninitialized variable being used.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit bfd8d3f2.

It turns out that this flushes things much too aggressiverly, and causes
lines to break up when the system logger races with new continuation
lines being printed.

There's a pending patch to make printk() flushing much more
straightforward, but it's too invasive for 4.9, so in the meantime let's
just not make the system message logging flush continuation lines.
They'll be flushed by the final newline anyway.
Suggested-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This file was converted to a separate module at commit 7a0786c1
("gp8psk: Fix DVB frontend attach"), because the DVB attach routines
require it to work.  However, I forgot to copy the MODULE_foo() macros
from the original module, causing this warning:

    WARNING: modpost: missing MODULE_LICENSE() in drivers/media/dvb-frontends/gp8psk-fe.o
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 7a0786c1 ("gp8psk: Fix DVB frontend attach")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull x86 fixes from Ingo Molnar:
 "Misc fixes:

   - fix an Intel/MID boot crash/hang bug

   - fix a cache topology mis-parsing bug on certain AMD CPUs

   - fix a virtualization firmware bug by adding a check+quirk
     workaround on the kernel side"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Deal with broken firmware (VMWare/XEN)
  x86/cpu/AMD: Fix cpu_llc_id for AMD Fam17h systems
  x86/platform/intel-mid: Retrofit pci_platform_pm_ops ->get_state hook

Pull irq fix from Ingo Molnar:
 "This fixes a genirq regression that resulted in the Intel/Broxton
  pinctrl/GPIO driver (and possibly others) spewing warnings"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Use irq type from irqdata instead of irqdesc

Pull perf fixes from Ingo Molnar:
 "An uncore PMU driver hardware enablement change for Intel SkyLake
  uncore PMUs (Skylake Y, U, H and S platforms), plus a number of
  tooling fixes for the histogram handling/displaying code"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel/uncore: Add more Intel uncore IMC PCI IDs for SkyLake
  perf hists: Fix column length on --hierarchy
  perf hists browser: Fix column indentation on --hierarchy
  perf hists browser: Show folded sign properly on --hierarchy
  perf hists browser: Fix indentation of folded sign on --hierarchy
  perf hist browser: Fix hierarchy column counts

Pull EFI fixes from Ingo Molnar:
 "A boot crash fix and a build warning fix"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/efi: Prevent mixed mode boot corruption with CONFIG_VMAP_STACK=y
  x86/efi: Fix EFI memmap pointer size warning

Pull NTB fixes from Jon Mason:
 "NTB bug fixes for ntb_hw_intel, ntb_perf, and ntb_pingpong.

  Also, a fixup to use jiffies in schedule_timeout_* call instead of a
  constant"

* tag 'ntb-4.9' of git://github.com/jonmason/ntb:
  ntb_perf: potential info leak in debugfs
  ntb: ntb_hw_intel: init peer_addr in struct intel_ntb_dev
  ntb: make DMA_OUT_RESOURCE_TO HZ independent
  ntb_transport: make DMA_OUT_RESOURCE_TO HZ independent
  NTB: ntb_hw_intel: Fix typo in module parameter descriptions
  ntb_pingpong: Fix db_init parameter description