V2 of code to add GPIO -> IRQ mappings to the
PFC table for the r8a73a4 SoC. Requires the IRQs
to be mapped at a fixed location in Linux IRQ
space. The actual IRQs are not handled by the
PFC, instead IRQC is used on r8a73a4.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The r8a73a4 SoC has sparse GPIO numbers. Declare ranges for pin numbers
in the PFC SoC data. Pin numbers shall be used with the GPIO API from
this point on.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add initial PFC support for the r8a73a4 SoC.

At this point only GPIO interface is supported, move to newer interfaces
planned as incremental changes.

Original authors are Morimoto-san with help from Yoshii-san, thanks to
them for the heavy lifting. Adjusted by Magnus to work together with
updated code in drivers/pinctrl.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The output pixel clocks can be used without the input pixel clocks.
Split them in different groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

GPIOs are now handled by a separate driver, remove GPIO data from the
SoC information structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Move GPIOs handling from the PFC device to separate GPIO devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When a GPIO is handled by a separate driver the pinmux
gpio_set_direction() handler won't be called. The pin mux type then need
to be configured to GPIO at request time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Boards/platforms that register dedicated GPIO devices will not supply a
memory resource for GPIOs. Try to locate the GPIO memory resource at
initialization time, and skip registration of the gpiochip if the
resource can't be found.

This is a temporary modification to ease the transition to separate GPIO
drivers. It should be reverted when all boards and platforms will have
been moved.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When implemented as a separate IP block, GPIOs should be handled by a
separate driver. To make this possible GPIO support needs to be optional
in the sh-pfc driver.

If no GPIO data registers are supplied in the SoC information structure
skip registration of the gpiochip.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The target is to get rid of function GPIOs completely. To reach this,
make function GPIOs support optional by skipping the function GPIO chip
registration if no function GPIOS are defined in SoC data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The board has 3 LEDs connected to GPIOs. Add a led-gpio device to
support them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Register the GPIO pin range, and request and free GPIO pins using the
pinctrl API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch is V3 of a GPIO driver for the R-Car series of
SoCs from Renesas. This driver is designed to be reusable
between multiple SoCs that share the same basic building block,
but so far it has only been used on R-Car H1 (r8a7779).

Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on a single I/O memory
range and the 32 GPIOs are hooked up a single interrupt.

In the case of R-Car H1 either external IRQ pins or GPIOs
with interrupts can be used for on-board interupts. For
external IRQs 4 pins are supported, and in the case of GPIO
there are 202 GPIOS as 202 interrupts hooked up via 6 driver
instances and to the GIC and the Cortex-A9 Quad.

At this point this driver is interfacing as a regular
platform device driver. In the future DT support will be
submitted as an incremental feature patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Function GPIOs are not used anymore, and all code use the GPIO numbers
directly. Remove the GPIOs enumeration.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Refactor the GPIO macro magic to use GPIO numbers directly instead of
the GPIO_GP_x_y enum entries. This will allow removing the GPIO enum
entries from the mach/r8a7779.h header.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

All r8a7779 platforms use the pinctrl API to control functions. Function
GPIOs are unused and unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

struct resource is defined in linux/ioport.h. Include it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The sh_pfc_phys_to_virt() function ends with a BUG() statement without a
return. When CONFIG_BUG isn't set the function will thus have no return
value. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Conflicts:
	drivers/pinctrl/sh-pfc/pfc-r8a7740.c

This merge is to provide r8a73a4 SoC files, which are added in the
soc branch and depended on by r8a73a4 pfc-changes which are to
be added to the pinmux branch.

The r8a7790 SoC supports LPAE and has memory window up to
0x2ffffffff. Convert to 64-bit addresses by enlarging
#addr-cells and #size-cells to 2.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The r8a73a4 SoC supports LPAE and has memory window up to
0x2ffffffff. Convert to 64-bit addresses by enlarging
#addr-cells and #size-cells to 2.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a platform device for the r8a7790 PFC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add IRQC interrupt controller support to r8a7790 by
hooking up a single IRQC instances to handle 4 external
IRQ signals. The IRQC controller is tied to SPIs of
the GIC. On r8a7790 the external IRQ pins routing is
handled by the PFC which is excluded from this patch.

Both platform devices and DT devices are added in this
patch. The platform device versions are used to provide
a static interrupt map configuration for board code
written in C.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add SCIF serial port support to the r8a7790 SoC by
adding platform devices for SCIFA0 -> SCIFA2 as well
as SCIFB0 -> SCIFB2 and SCIF0 -> SCIF1 together with
clock bindings. DT device description is excluded at
this point since such bindings are still under
development.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add initial support for the r8a7790 SoC including:
 - Single Cortex-A15 CPU Core
 - GIC
 - Architecture timer

No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

There is no reason each CPU's own function has to exist in common.h.
r8a7779_xxx() go to r8a7779.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

There is no reason each CPU's own function has to exist in common.h.
r8a7740_xxx() go to r8a7740.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

There is no reason each CPU's own function has to exist in common.h.
sh73a0_xxx() go to sh73a0.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

There is no reason each CPU's own function has to exist in common.h.
sh7372_xxx() go to sh7372.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

R-Car H1 has many clocks, and it is possible to read/use clock ratio
of these clocks from FRQMRx as DIV4 clocks.
But, these ratio are fixed value and these are decided
by MD pin status.
This means that we can use fixed ratio clock via MD pin status,
instead of DIV4 clocks.

This patch reads MD pin status, and sets PLLA clock (= root clock),
and used fixed ratio clock for other clocks.
It was tesed on marzen board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Current clock-r8a7740 is using own implement
for each divX clocks.
This patch switches to use fixed ratio clock,
and was tesed on armadillo board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Current clock-r8a7740's DIV4/DIV6/MSTP implemented area and
its comment are mismatching.
This patch tidyup its comment/implementation area.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Current clock-sh73a0 is using own implement
for each divX clocks.
This patch switches to use fixed ratio clock,
and was tesed on kzm9g board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Current clock-sh7372 is using own implement
for each divX clocks.
This patch switches to use fixed ratio clock,
and was tesed on mackerel board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Renesas chip has many clocks inside,
and some of them are using fixed ratio via parent clock.
Current shmobile clock code is using own divX_recalc function
and divX_clk_ops.
This patch can reduce these code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV4_ZT* clocks are for debugging and trace bus clock.
It is not necessary to control it from Linux/Software.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV4_ZT* clocks are for debugging and trace bus clock.
It is not necessary to control it from Linux/Software.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a TWD clock on sh73a0 for the smp_twd driver to properly update the
clock's frequency upon cpufreq events.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

With the added capabilty of the intc_irqpin driver to handle shared
external IRQs, all prerequisites are fulfilled and we are ready to
migrate completely to GIC. This includes the following steps:

- Kconfig:	select ARM_GIC and RENESAS_INTC_IRQPIN
- intc-r8a7740: Throw out all legacy INTC code and init the GIC. We need
  		to mask out all shared IRQs as it is needed by the
		shared intc_irqpin driver.
- setup-r8a7740: Add 4 irqpin devices to handle external IRQs and update
		all IRQ numbers to point to the GIC SPI.
- board-armadillo: Update all IRQ numbers to point to the GIC SPI.
- pfc-r8a7740:	Update all IRQ numbers of the GPIOs to point to the GIC
		SPI.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

You can get current thermal by
> cat /sys/class/thermal/thermal_zone?/temp
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>