- 23 Jul, 2018 28 commits
-
-
David S. Miller authored
Bryan Whitehead says: ==================== lan743x: Add features to lan743x driver This patch series adds extra features to the lan743x driver. Updates for v4: Patch 6/8 - Modified get/set_wol to use super set of MAC and PHY driver support. Patch 7/9 - In set_eee, return the return value from phy_ethtool_set_eee. Updates for v3: Removed patch 9 from this series, regarding PTP support Patch 6/8 - Add call to phy_ethtool_get_wol to lan743x_ethtool_get_wol Patch 7/8 - Add call to phy_ethtool_set_eee on (!eee->eee_enabled) Updates for v2: Patch 3/9 - Used ARRAY_SIZE macro in lan743x_ethtool_get_ethtool_stats. Patch 5/9 - Used MAX_EEPROM_SIZE in lan743x_ethtool_set_eeprom. Patch 6/9 - Removed unnecessary read of PMT_CTL. Used CRC algorithm from lib. Removed PHY interrupt settings from lan743x_pm_suspend Change "#if CONFIG_PM" to "#ifdef CONFIG_PM" ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Bryan Whitehead authored
Implement RSS support Signed-off-by:
Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by:
-
Bryan Whitehead authored
Implement EEE support Signed-off-by:
-
Bryan Whitehead authored
Implement power management Supports suspend, resume, and Wake on LAN Signed-off-by:
-
Bryan Whitehead authored
Implement ethtool eeprom access Also provides access to OTP (One Time Programming) Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Bryan Whitehead authored
Implement ethtool message level Signed-off-by:
-
Bryan Whitehead authored
Implement ethtool statistics Signed-off-by:
-
Bryan Whitehead authored
Use default link setting functions Signed-off-by:
-
Bryan Whitehead authored
Implement ethtool get_drvinfo Signed-off-by:
-
David S. Miller authored
Sergei Shtylyov says: ==================== sh_eth: clean up the TSU register accessors Here's a set of 5 patches against DaveM's 'net-next.git' repo. They do a final clean up of the TSU register accessors... ==================== Signed-off-by: -
Sergei Shtylyov authored
sh_eth_tsu_read_entry() is still asymmetric with sh_eth_tsu_write_entry() WRT their prototypes -- make them symmetric by passing to the former a TSU register offset instead of its address and also adding the (now necessary) 'ndev' parameter... Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Sergei Shtylyov authored
We can add the TSU register base address to a TSU register offset right in sh_eth_tsu_write_entry(), no need to do it in its callers... Signed-off-by:
-
Sergei Shtylyov authored
With sh_eth_tsu_get_offset() now actually returning TSU register's offset, we can at last use it in sh_eth_tsu_{read|write}(). Somehow this saves 248 bytes of object code with AArch64 gcc 4.8.5... :-) Signed-off-by: -
Sergei Shtylyov authored
sh_eth_tsu_get_offset(), despite its name, returns a TSU register's address, not its offset. Make this function match its name and return a register's offset from the TSU registers base address instead. Signed-off-by:
-
Sergei Shtylyov authored
sh_eth_tsu_get_offset() is called several times by the driver, remove *inline* and move that function from the header to the driver itself to let gcc decide whether to expand it inline or not... Signed-off-by:
-
YueHaibing authored
qe_muram_alloc return a unsigned long integer,which should not compared with zero. check it using IS_ERR_VALUE() to fix this. Fixes: c19b6d24 ("drivers/net: support hdlc function for QE-UCC") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
David S. Miller authored
Ursula Braun says: ==================== net/smc: patches 2018-07-23 here are some small patches for SMC: Just the first patch contains a functional change. It allows to differ between the modes SMCR and SMCD on s390 when monitoring SMC sockets. The remaining patches are cleanups without functional changes. ==================== Signed-off-by: -
Ursula Braun authored
The page map address is already stored in the RMB descriptor. There is no need to derive it from the cpu_addr value. Signed-off-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
-
Ursula Braun authored
Link group field tokens_used_mask is a bitmap. Use macro DECLARE_BITMAP for its definition. Signed-off-by:
-
Stefan Raspl authored
Replace a frequently used construct with a more readable variant, reducing the code. Also might come handy when we start to support more than a single per link group. Signed-off-by:
Stefan Raspl <raspl@linux.ibm.com> Signed-off-by:
-
Stefan Raspl authored
The functions to read and write cursors are exclusively used to copy cursors. Therefore switch to a respective function instead. Signed-off-by:
-
Karsten Graul authored
Rename field diag_fallback into diag_mode and set the smc mode of a connection explicitly. Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
-
Petr Machata authored
Support for device-only IPv6 multipath next hops was dropped in commit 33bd5ac5 ("net/ipv6: Revert attempt to simplify route replace and append") and as of commit b5d2d75e ("net/ipv6: Do not allow device only routes via the multipath API"), attempts to add a next hop like that yield an explicit diagnostic. Correspondingly, drop the IPv6 parts of GRE multipath test that are supposed to test that code. Signed-off-by:
Petr Machata <petrm@mellanox.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
YueHaibing authored
Replace calls to kmalloc followed by a memcpy with a direct call to kmemdup. Signed-off-by:
-
David S. Miller authored
Nikolay Aleksandrov says: ==================== net: bridge: add support for backup port This set introduces a new bridge port option that allows any port to have any other port (in the same bridge of course) as its backup and traffic will be forwarded to the backup port when the primary goes down. This is mainly used in MLAG and EVPN setups where we have peerlink path which is a backup of many (or even all) ports and is a participating bridge port itself. There's more detailed information in patch 02. Patch 01 just prepares the port sysfs code for options that take raw value. The main issues that this set solves are scalability and fallback latency. We have used similar code for over 6 months now to bring the fallback latency of the backup peerlink down and avoid fdb notification storms. Also due to the nature of master devices such setup is currently not possible, and last but not least having tens of thousands of fdbs require thousands of calls to switch. I've also CCed our MLAG experts that have been using similar option. Roopa also adds: "Two switches acting in a MLAG pair are connected by the peerlink interface which is a bridge port. the config on one of the switches looks like the below. The other switch also has a similar config. eth0 is connected to one port on the server. And the server is connected to both switches. br0 -- team0---eth0 | -- switch-peerlink switch-peerlink becomes the failover/backport port when say team0 to the server goes down. Today, when team0 goes down, control plane has to withdraw all the fdb entries pointing to team0 and re-install the fdb entries pointing to switch-peerlink...and restore the fdb entries when team0 comes back up again. and this is the problem we are trying to solve. This also becomes necessary when multihoming is implemented by a standard like E-VPN https://tools.ietf.org/html/rfc8365#section-8 where the 'switch-peerlink' is an overlay vxlan port (like nikolay mentions in his patch commit). In these implementations, the fdb scale can be much larger. On why bond failover cannot be used here ?: the point that nikolay was alluding to is, switch-peerlink in the above example is a bridge port and is a failover/backport port for more than one or all ports in the bridge br0. And you cannot enslave switch-peerlink into a second level team with other bridge ports. Hence a multi layered team device is not an option (FWIW, switch-peerlink is also a teamed interface to the peer switch)." v3: Added Roopa's explanation and diagram v2: In patch 01 use kstrdup/kfree to avoid casting the const buf. In order to avoid using GFP_ATOMIC or always allocating I kept the spinlock inside each branch. ==================== Signed-off-by: -
Nikolay Aleksandrov authored
This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which allows to set a backup port to be used for known unicast traffic if the port has gone carrier down. The backup pointer is rcu protected and set only under RTNL, a counter is maintained so when deleting a port we know how many other ports reference it as a backup and we remove it from all. Also the pointer is in the first cache line which is hot at the time of the check and thus in the common case we only add one more test. The backup port will be used only for the non-flooding case since it's a part of the bridge and the flooded packets will be forwarded to it anyway. To remove the forwarding just send a 0/non-existing backup port. This is used to avoid numerous scalability problems when using MLAG most notably if we have thousands of fdbs one would need to change all of them on port carrier going down which takes too long and causes a storm of fdb notifications (and again when the port comes back up). In a Multi-chassis Link Aggregation setup usually hosts are connected to two different switches which act as a single logical switch. Those switches usually have a control and backup link between them called peerlink which might be used for communication in case a host loses connectivity to one of them. We need a fast way to failover in case a host port goes down and currently none of the solutions (like bond) cannot fulfill the requirements because the participating ports are actually the "master" devices and must have the same peerlink as their backup interface and at the same time all of them must participate in the bridge device. As Roopa noted it's normal practice in routing called fast re-route where a precalculated backup path is used when the main one is down. Another use case of this is with EVPN, having a single vxlan device which is backup of every port. Due to the nature of master devices it's not currently possible to use one device as a backup for many and still have all of them participate in the bridge (which is master itself). More detailed information about MLAG is available at the link below. https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG Further explanation and a diagram by Roopa: Two switches acting in a MLAG pair are connected by the peerlink interface which is a bridge port. the config on one of the switches looks like the below. The other switch also has a similar config. eth0 is connected to one port on the server. And the server is connected to both switches. br0 -- team0---eth0 | -- switch-peerlink Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Nikolay Aleksandrov authored
This patch adds a new alternative store callback for port sysfs options which takes a raw value (buf) and can use it directly. It is needed for the backup port sysfs support since we have to pass the device by its name. Signed-off-by:
-
YueHaibing authored
Use dma_zalloc_coherent instead of dma_alloc_coherent followed by memset 0. Signed-off-by:
-
- 22 Jul, 2018 12 commits
-
-
Jakub Kicinski authored
After device is stopped we reset the rings by moving all free buffers to positions [0, cnt - 2], and clear the position cnt - 1 in the ring. We then proceed to clear the read/write pointers. This means that if we try to reset the ring again the code will assume that the next to fill buffer is at position 0 and swap it with cnt - 1. Since we previously cleared position cnt - 1 it will lead to leaking the first buffer and leaving ring in a bad state. This scenario can only happen if FW communication fails, in which case the ring will never be used again, so the fact it's in a bad state will not be noticed. Buffer leak is the only problem. Don't try to move buffers in the ring if the read/write pointers indicate the ring was never used or have already been reset. nfp_net_clear_config_and_disable() is now fully idempotent. Found by code inspection, FW communication failures are very rare, and reconfiguring a live device is not common either, so it's unlikely anyone has ever noticed the leak. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
Now that we have offload replay infrastructure added by commit 32636742 ("net: sched: call reoffload op on block callback reg") and flows are guaranteed to be removed correctly, we can revert commit 951a8ee6 ("nfp: reject binding to shared blocks"). Signed-off-by:
John Hurley <john.hurley@netronome.com> Signed-off-by:
-
Vitaly Kuznetsov authored
Commit f599c64f ("xen-netfront: Fix race between device setup and open") changed the initialization order: xennet_create_queues() now happens before we do register_netdev() so using netdev->name in xennet_init_queue() is incorrect, we end up with the following in /proc/interrupts: 60: 139 0 xen-dyn -event eth%d-q0-tx 61: 265 0 xen-dyn -event eth%d-q0-rx 62: 234 0 xen-dyn -event eth%d-q1-tx 63: 1 0 xen-dyn -event eth%d-q1-rx and this looks ugly. Actually, using early netdev name (even when it's already set) is also not ideal: nowadays we tend to rename eth devices and queue name may end up not corresponding to the netdev name. Use nodename from xenbus device for queue naming: this can't change in VM's lifetime. Now /proc/interrupts looks like 62: 202 0 xen-dyn -event device/vif/0-q0-tx 63: 317 0 xen-dyn -event device/vif/0-q0-rx 64: 262 0 xen-dyn -event device/vif/0-q1-tx 65: 17 0 xen-dyn -event device/vif/0-q1-rx Fixes: f599c64f ("xen-netfront: Fix race between device setup and open") Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by:
-
Randy Dunlap authored
Add MODULE_LICENSE() to net/dsa/realtek.o to fix build warning message. WARNING: modpost: missing MODULE_LICENSE() in drivers/net/dsa/realtek.o Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Nikolay Aleksandrov authored
As was recently discussed [1], let's avoid casting the const buf in bonding_sysfs_store_option and use kstrndup/kfree instead. [1] http://lists.openwall.net/netdev/2018/07/22/25Signed-off-by:
-
David S. Miller authored
Jason Wang says: ==================== TX used ring batched updating for vhost This series implement batch updating of used ring for TX. This help to reduce the cache contention on used ring. The idea is first split datacopy path from zerocopy, and do only batching for datacopy. This is because zercopy had already supported its own batching. TX PPS was increased 25.8% and Netperf TCP does not show obvious differences. The split of datapath will also be helpful for future implementation like in order completion. ==================== Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Jason Wang authored
Like commit e2b3b35e ("vhost_net: batch used ring update in rx"), this patches implements batch used ring update for datacopy TX (zerocopy has already done some kind of batching). Testpmd transmission from guest to host (XDP_DROP on tap) shows 25.8% improvement (from ~3.1Mpps to ~3.9Mpps) on Broadwell i7-5600U CPU @ 2.60GHz machine. Netperf TCP tests does not show obvious differences. Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Jason Wang authored
A more generic name which could be used for TX as well. Signed-off-by:
-
Jason Wang authored
Rename for reusing this for TX. Signed-off-by:
-
Jason Wang authored
Instead of mixing zerocopy and datacopy logics, this patch tries to split datacopy logic out. This results for a more compact code and ad-hoc optimization could be done on top more easily. Signed-off-by:
-
Jason Wang authored
Introduce tx_can_batch() to determine whether TX could be batched. This will help to reduce the code duplication in the future. Signed-off-by:
-
Jason Wang authored
Factor out logic of getting tx buffer and iov iter initialization. This will be used for reducing codes duplication in the future. Signed-off-by:
-
