Pull io_uring fixes from Jens Axboe:
 "Here's a set of fixes for io_uring:

   - Various fixes with cleanups from Pavel, fixing corner cases where
     we're not correctly dealing with iovec cleanup.

   - Clarify that statx/openat/openat2 don't accept fixed files

   - Buffered raw device write EOPTNOTSUPP fix

   - Ensure async workers grab current->fs

   - A few task exit fixes with pending requests that grab the file
     table

   - send/recvmsg async load fix

   - io-wq offline node setup fix

   - CQ overflow flush in poll"

* tag 'io_uring-5.6-2020-02-14' of git://git.kernel.dk/linux-block: (21 commits)
  io_uring: prune request from overflow list on flush
  io-wq: don't call kXalloc_node() with non-online node
  io_uring: retain sockaddr_storage across send/recvmsg async punt
  io_uring: cancel pending async work if task exits
  io-wq: add io_wq_cancel_pid() to cancel based on a specific pid
  io-wq: make io_wqe_cancel_work() take a match handler
  io_uring: fix openat/statx's filename leak
  io_uring: fix double prep iovec leak
  io_uring: fix async close() with f_op->flush()
  io_uring: allow AT_FDCWD for non-file openat/openat2/statx
  io_uring: grab ->fs as part of async preparation
  io-wq: add support for inheriting ->fs
  io_uring: retry raw bdev writes if we hit -EOPNOTSUPP
  io_uring: add cleanup for openat()/statx()
  io_uring: fix iovec leaks
  io_uring: remove unused struct io_async_open
  io_uring: flush overflowed CQ events in the io_uring_poll()
  io_uring: statx/openat/openat2 don't support fixed files
  io_uring: fix deferred req iovec leak
  io_uring: fix 1-bit bitfields to be unsigned
  ...

Pull networking fixes from David Miller:

 1) Fix interrupt name truncation in mv88e6xxx dsa driver, from Andrew
    Lunn.

 2) Process generic XDP even if SKB is cloned, from Toke Høiland-Jørgensen.

 3) Fix leak of kernel memory to userspace in smc, from Eric Dumazet.

 4) Add some missing netlink attribute validation to matchall and
    flower, from Davide Caratti.

 5) Send icmp responses properly when NAT has been applied to the frame
    before we get to the tunnel emitting the icmp, from Jason Donenfeld.

 6) Make sure there is enough SKB headroom when adding dsa tags for qca
    and ar9331. From Per Forlin.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
  netdevice.h: fix all kernel-doc and Sphinx warnings
  net: dsa: tag_ar9331: Make sure there is headroom for tag
  net: dsa: tag_qca: Make sure there is headroom for tag
  net, ip6_tunnel: enhance tunnel locate with link check
  net/smc: no peer ID in CLC decline for SMCD
  net/smc: transfer fasync_list in case of fallback
  net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples()
  net: hns3: fix VF bandwidth does not take effect in some case
  net: hns3: add management table after IMP reset
  mac80211: fix wrong 160/80+80 MHz setting
  cfg80211: add missing policy for NL80211_ATTR_STATUS_CODE
  xfrm: interface: use icmp_ndo_send helper
  wireguard: device: use icmp_ndo_send helper
  sunvnet: use icmp_ndo_send helper
  gtp: use icmp_ndo_send helper
  icmp: introduce helper for nat'd source address in network device context
  net/sched: flower: add missing validation of TCA_FLOWER_FLAGS
  net/sched: matchall: add missing validation of TCA_MATCHALL_FLAGS
  net/flow_dissector: remove unexist field description
  page_pool: refill page when alloc.count of pool is zero
  ...

Pull power management fixes from Rafael Wysocki:
 "Fix three issues related to the handling of wakeup events signaled
  through the ACPI SCI while suspended to idle (Rafael Wysocki) and
  unexport an internal cpufreq variable (Yangtao Li)"

* tag 'pm-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system
  ACPICA: Introduce acpi_any_gpe_status_set()
  ACPI: PM: s2idle: Avoid possible race related to the EC GPE
  ACPI: EC: Fix flushing of pending work
  cpufreq: Make cpufreq_global_kobject static

Pull sound fixes from Takashi Iwai:
 "The only common change is the regression fix of the previous PCM fix
  patch for managed buffers while the rest are usual suspects, USB-audio
  and HD-audio device-specific quirks.

  The change for UAC2 clock validation workaround became a bit big, but
  the changes are fairly straightforward"

* tag 'sound-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: pcm: Fix double hw_free calls
  ALSA: usb-audio: Add clock validity quirk for Denon MC7000/MCX8000
  ALSA: hda/realtek - Fix silent output on MSI-GL73
  ALSA: hda/realtek - Add more codec supported Headset Button
  ALSA: usb-audio: Apply sample rate quirk for Audioengine D1
  ALSA: usb-audio: Fix UAC2/3 effect unit parsing
  ALSA: usb-audio: Apply 48kHz fixed rate playback for Jabra Evolve 65 headset

Pull drm fixes from Dave Airlie:
 "The core has a build fix for edid code on certain compilers/arches/,
  one MST fix and one vgem fix. Regular amdgpu fixes, and a couple of
  small driver fixes.

  The i915 fixes are bit larger than normal for this stage, but they
  were having CI issues last week, and they hadn't sent any fixes last
  week due to this.

  core:
   - edid build fix

  mst:
   - fix NULL ptr deref

  vgem:
   - fix close after free

  msm:
   - better dma-api usage

  sun4i:
   - disable allow_fb_modifiers

  amdgpu:
   - Additional OD fixes for navi
   - Misc display fixes
   - VCN 2.5 DPG fix
   - Prevent build errors on PowerPC on some configs
   - GDS EDC fix

  i915:
   - dsi/acpi fixes
   - gvt locking and allocation fixes
   - gem/gt fixes
   - bios timing parameters fix"

* tag 'drm-fixes-2020-02-14' of git://anongit.freedesktop.org/drm/drm: (50 commits)
  drm/i915: Mark the removal of the i915_request from the sched.link
  drm/i915/execlists: Reclaim the hanging virtual request
  drm/i915/execlists: Take a reference while capturing the guilty request
  drm/i915/execlists: Offline error capture
  drm/i915/gt: Allow temporary suspension of inflight requests
  drm/i915: Keep track of request among the scheduling lists
  drm/i915/gem: Tighten checks and acquiring the mmap object
  drm/i915: Fix preallocated barrier list append
  drm/i915/gt: Acquire ce->active before ce->pin_count/ce->pin_mutex
  drm/i915: Tighten atomicity of i915_active_acquire vs i915_active_release
  drm/i915: Stub out i915_gpu_coredump_put
  drm/amdgpu:/navi10: use the ODCAP enum to index the caps array
  drm/amdgpu: update smu_v11_0_pptable.h
  drm/amdgpu: correct comment to clear up the confusion
  drm/amd/display: DCN2.x Do not program DPPCLK if same value
  drm/amd/display: Don't map ATOM_ENABLE to ATOM_INIT
  drm/amdgpu/vcn2.5: fix warning
  drm/amdgpu: limit GDS clearing workaround in cold boot sequence
  drm/amdgpu: fix amdgpu pmu to use hwc->config instead of hwc->conf
  amdgpu: Prevent build errors regarding soft/hard-float FP ABI tags
  ...

Eliminate all kernel-doc and Sphinx warnings in
<linux/netdevice.h>.  Fixes these warnings:

../include/linux/netdevice.h:2100: warning: Function parameter or member 'gso_partial_features' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'l3mdev_ops' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xfrmdev_ops' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'tlsdev_ops' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'name_assign_type' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'ieee802154_ptr' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'mpls_ptr' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xdp_prog' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'gro_flush_timeout' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xdp_bulkq' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xps_cpus_map' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xps_rxqs_map' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'qdisc_hash' not described in 'net_device'
../include/linux/netdevice.h:3552: WARNING: Inline emphasis start-string without end-string.
../include/linux/netdevice.h:3552: WARNING: Inline emphasis start-string without end-string.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per Forlin says:

====================
net: dsa: Make sure there is headroom for tag

Sorry for re-posting yet another time....
I manage to include multiple email-senders and forgot to include cover-letter.
Let's hope everyhthing is in order this time.

Fix two tag drivers to make sure there is headroom for the tag data.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.
Signed-off-by: Per Forlin <perfn@axis.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.
Signed-off-by: Per Forlin <perfn@axis.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With ipip, it is possible to create an extra interface explicitly
attached to a given physical interface:

  # ip link show tunl0
  4: tunl0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ipip 0.0.0.0 brd 0.0.0.0
  # ip link add tunl1 type ipip dev eth0
  # ip link show tunl1
  6: tunl1@eth0: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ipip 0.0.0.0 brd 0.0.0.0

But it is not possible with ip6tnl:

  # ip link show ip6tnl0
  5: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop state DOWN mode DEFAULT group default qlen 1000
      link/tunnel6 :: brd ::
  # ip link add ip6tnl1 type ip6tnl dev eth0
  RTNETLINK answers: File exists

This patch aims to make it possible by adding link comparaison in both
tunnel locate and lookup functions; we also modify mtu calculation when
attached to an interface with a lower mtu.

This permits to make use of x-netns communication by moving the newly
created tunnel in a given netns.
Signed-off-by: William Dauchy <w.dauchy@criteo.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-net-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just a few fixes:
 * avoid running out of tracking space for frames that need
   to be reported to userspace by using more bits
 * fix beacon handling suppression by adding some relevant
   elements to the CRC calculation
 * fix quiet mode in action frames
 * fix crash in ethtool for virt_wifi and similar
 * add a missing policy entry
 * fix 160 & 80+80 bandwidth to take local capabilities into
   account
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Karsten Graul says:

====================
net/smc: fixes for -net

Fix a syzbot finding and a problem with the CLC handshake content.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Just SMCR requires a CLC Peer ID, but not SMCD. The field should be
zero for SMCD.

Fixes: c758dfdd ("net/smc: add SMC-D support in CLC messages")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SMC does not work together with FASTOPEN. If sendmsg() is called with
flag MSG_FASTOPEN in SMC_INIT state, the SMC-socket switches to
fallback mode. To handle the previous ioctl FIOASYNC call correctly
in this case, it is necessary to transfer the socket wait queue
fasync_list to the internal TCP socket.

Reported-by: syzbot+4b1fe8105f8044a26162@syzkaller.appspotmail.com
Fixes: ee9dfbef ("net/smc: handle sockopts forcing fallback")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: fixes for -net

This series includes three bugfixes for the HNS3 ethernet driver.

[patch 1] fixes a management table lost issue after IMP reset.
[patch 2] fixes a VF bandwidth configuration not work problem.
[patch 3] fixes a problem related to IPv6 address copying.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The IPv6 address defined in struct in6_addr is specified as
big endian, but there is no specified endian in struct
hclge_fd_rule_tuples, so it  will cause a problem if directly
use memcpy() to copy ipv6 address between these two structures
since this field in struct hclge_fd_rule_tuples is little endian.

This patch fixes this problem by using be32_to_cpu() to convert
endian of IPv6 address of struct in6_addr before copying.

Fixes: d93ed94f ("net: hns3: add aRFS support for PF")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When enabling 4 TC after setting the bandwidth of VF, the bandwidth
of VF will resume to default value, because of the qset resources
changed in this case.

This patch fixes it by using a fixed VF's qset resources according to
HNAE3_MAX_TC macro.

Fixes: ee9e4424 ("net: hns3: add support for configuring bandwidth of VF on the host")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current process, the management table is missing after the
IMP reset. This patch adds the management table to the reset process.

Fixes: f5aac71c ("net: hns3: add manager table initialization for hardware")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* pm-cpufreq:
  cpufreq: Make cpufreq_global_kobject static

Before this patch, STA's would set new width of 160/80+80 MHz based on AP capability only.
This is wrong because STA may not support > 80MHz BW.
Fix is to verify STA has 160/80+80 MHz capability before increasing its width to > 80MHz.

The "support_80_80" and "support_160" setting is based on:
"Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW
Support subfield at a STA transmitting the VHT Capabilities Information field"
From "Draft P802.11REVmd_D3.0.pdf"
Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com>
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20200210130728.23674-1-shay.bar@celeno.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

The nl80211_policy is missing for NL80211_ATTR_STATUS_CODE attribute.
As a result, for strictly validated commands, it's assumed to not be
supported.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200213131608.10541-2-sergey.matyukevich.os@quantenna.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Merge tag 'drm-intel-next-fixes-2020-02-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v5.6-rc2

Most of these were aimed at a "next fixes" pull already during the merge
window, but there were issues with the baseline I used, which resulted
in a lot of issues in CI. I've regenerated this stuff piecemeal now,
adding gradually to it, and it seems healthy now.

Due to the issues this is much bigger than I'd like. But it was
obviously necessary to take the time to ensure it's not garbage...
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/878sl6yfrn.fsf@intel.com

Merge tag 'amd-drm-fixes-5.6-2020-02-12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes

amd-drm-fixes-5.6-2020-02-12:

amdgpu:
- Additional OD fixes for navi
- Misc display fixes
- VCN 2.5 DPG fix
- Prevent build errors on PowerPC on some configs
- GDS EDC fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200212224746.3992-1-alexander.deucher@amd.com

Merge tag 'drm-misc-next-fixes-2020-02-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

drm-misc-next fixes for v5.6:
- Fix build error in drm/edid.
- Plug close-after-free race in vgem_gem_create.
- Handle CONFIG_DMA_API_DEBUG_SG better in drm/msm.
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/551b6183-a581-9d12-10a9-24cd929de425@linux.intel.com

Fixes for v5.6:
- Revert allow_fb_modifiers in sun4i, as it causes a regression for DE2 and DE3.
- Fix null pointer deref in drm_dp_mst_process_up_req().
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/672810c3-4212-0a46-337b-2cb855573fd2@linux.intel.com

Carter reported an issue where he could produce a stall on ring exit,
when we're cleaning up requests that match the given file table. For
this particular test case, a combination of a few things caused the
issue:

- The cq ring was overflown
- The request being canceled was in the overflow list

The combination of the above means that the cq overflow list holds a
reference to the request. The request is canceled correctly, but since
the overflow list holds a reference to it, the final put won't happen.
Since the final put doesn't happen, the request remains in the inflight.
Hence we never finish the cancelation flush.

Fix this by removing requests from the overflow list if we're canceling
them.

Cc: stable@vger.kernel.org # 5.5
Reported-by: Carter Li 李通洲 <carter.li@eoitek.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull arm64 fixes from Will Deacon:
 "Summary below, but it's all reasonably straightforward. There are some
  more fixes on the horizon, but nothing disastrous yet.

  Summary:

   - Fix build when KASLR is enabled but CONFIG_ARCH_RANDOM is not set

   - Fix context-switching of SSBS state on systems that implement it

   - Fix spinlock compiler warning introduced during the merge window

   - Fix incorrect header inclusion (linux/clk-provider.h)

   - Use SYSCTL_{ZERO,ONE} instead of rolling our own static variables

   - Don't scream if optional SMMUv3 PMU irq is missing

   - Remove some unused function prototypes"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: time: Replace <linux/clk-provider.h> by <linux/of_clk.h>
  arm64: Fix CONFIG_ARCH_RANDOM=n build
  perf/smmuv3: Use platform_get_irq_optional() for wired interrupt
  arm64/spinlock: fix a -Wunused-function warning
  arm64: ssbs: Fix context-switch when SSBS is present on all CPUs
  arm64: use shared sysctl constants
  arm64: Drop do_el0_ia_bp_hardening() & do_sp_pc_abort() declarations

Pull GPIO fixes from Linus Walleij:

 - Revert two patches to gpio_do_set_config() and implement the proper
   solution that works, also drop an unecessary call in set_config()

 - Fix up the lockdep class for hierarchical IRQ domains.

 - Remove some bridge code for line directions.

 - Fix a register access bug in the Xilinx driver.

* tag 'gpio-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: sifive: fix static checker warning
  spmi: pmic-arb: Set lockdep class for hierarchical irq domains
  gpio: xilinx: Fix bug where the wrong GPIO register is written to
  gpiolib: remove unnecessary argument from set_config call
  gpio: bd71828: Remove unneeded defines for GPIO_LINE_DIRECTION_IN/OUT
  MAINTAINERS: Sort entries in database for GPIO
  gpiolib: fix gpio_do_set_config()
  Revert "gpiolib: remove set but not used variable 'config'"
  Revert "gpiolib: Remove duplicated function gpio_do_set_config()"

Jason A. Donenfeld says:

====================
icmp: account for NAT when sending icmps from ndo layer

The ICMP routines use the source address for two reasons:

1. Rate-limiting ICMP transmissions based on source address, so
   that one source address cannot provoke a flood of replies. If
   the source address is wrong, the rate limiting will be
   incorrectly applied.

2. Choosing the interface and hence new source address of the
   generated ICMP packet. If the original packet source address
   is wrong, ICMP replies will be sent from the wrong source
   address, resulting in either a misdelivery, infoleak, or just
   general network admin confusion.

Most of the time, the icmp_send and icmpv6_send routines can just reach
down into the skb's IP header to determine the saddr. However, if
icmp_send or icmpv6_send is being called from a network device driver --
there are a few in the tree -- then it's possible that by the time
icmp_send or icmpv6_send looks at the packet, the packet's source
address has already been transformed by SNAT or MASQUERADE or some other
transformation that CONNTRACK knows about. In this case, the packet's
source address is most certainly the *wrong* source address to be used
for the purpose of ICMP replies.

Rather, the source address we want to use for ICMP replies is the
original one, from before the transformation occurred.

Fortunately, it's very easy to just ask CONNTRACK if it knows about this
packet, and if so, how to fix it up. The saddr is the only field in the
header we need to fix up, for the purposes of the subsequent processing
in the icmp_send and icmpv6_send functions, so we do the lookup very
early on, so that the rest of the ICMP machinery can progress as usual.

Changes v3->v4:
- Add back the skb_shared checking, since the previous assumption isn't
  actually true [Eric]. This implies dropping the additional patches v3 had
  for removing skb_share_check from various drivers. We can revisit that
  general set of ideas later, but that's probably better suited as a net-next
  patchset rather than this stable one which is geared at fixing bugs. So,
  this implements things in the safe conservative way.

Changes v2->v3:
- Add selftest to ensure this actually does what we want and never regresses.
- Check the size of the skb header before operating on it.
- Use skb_ensure_writable to ensure we can modify the cloned skb [Florian].
- Conditionalize this on IPS_SRC_NAT so we don't do anything unnecessarily
  [Florian].
- It turns out that since we're calling these from the xmit path,
  skb_share_check isn't required, so remove that [Florian]. This simplifes the
  code a bit too. **The supposition here is that skbs passed to ndo_start_xmit
  are _never_ shared. If this is not correct NOW IS THE TIME TO PIPE UP, for
  doom awaits us later.**
- While investigating the shared skb business, several drivers appeared to be
  calling it incorrectly in the xmit path, so this series also removes those
  unnecessary calls, based on the supposition mentioned in the previous point.

Changes v1->v2:
- icmpv6 takes subtly different types than icmpv4, like u32 instead of be32,
  u8 instead of int.
- Since we're technically writing to the skb, we need to make sure it's not
  a shared one [Dave, 2017].
- Restore the original skb data after icmp_send returns. All current users
  are freeing the packet right after, so it doesn't matter, but future users
  might not.
- Remove superfluous route lookup in sunvnet [Dave].
- Use NF_NAT instead of NF_CONNTRACK for condition [Florian].
- Include this cover letter [Dave].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Because xfrmi is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because wireguard is calling icmp from network device context, it should
use the ndo helper so that the rate limiting applies correctly.  This
commit adds a small test to the wireguard test suite to ensure that the
new functions continue doing the right thing in the context of
wireguard. It does this by setting up a condition that will definately
evoke an icmp error message from the driver, but along a nat'd path.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because sunvnet is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly. While we're
at it, doing the additional route lookup before calling icmp_ndo_send is
superfluous, since this is the job of the icmp code in the first place.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because gtp is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This introduces a helper function to be called only by network drivers
that wraps calls to icmp[v6]_send in a conntrack transformation, in case
NAT has been used. We don't want to pollute the non-driver path, though,
so we introduce this as a helper to be called by places that actually
make use of this, as suggested by Florian.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull crypto fix from Herbert Xu:
 "This fixes a Kconfig anomaly when lib/crypto is enabled without Crypto
  API"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: Kconfig - allow tests to be disabled when manager is disabled

Davide Caratti says:

====================
add missing validation of 'skip_hw/skip_sw'

ensure that all classifiers currently supporting HW offload
validate the 'flags' parameter provided by user:

- patch 1/2 fixes cls_matchall
- patch 2/2 fixes cls_flower
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

unlike other classifiers that can be offloaded (i.e. users can set flags
like 'skip_hw' and 'skip_sw'), 'cls_flower' doesn't validate the size of
netlink attribute 'TCA_FLOWER_FLAGS' provided by user: add a proper entry
to fl_policy.

Fixes: 5b33f488 ("net/flower: Introduce hardware offload support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

unlike other classifiers that can be offloaded (i.e. users can set flags
like 'skip_hw' and 'skip_sw'), 'cls_matchall' doesn't validate the size
of netlink attribute 'TCA_MATCHALL_FLAGS' provided by user: add a proper
entry to mall_policy.

Fixes: b87f7936 ("net/sched: Add match-all classifier hw offloading.")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

@thoff has moved to struct flow_dissector_key_control.

Fixes: 42aecaa9 ("net: Get skb hash over flow_keys structure")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"do {} while" in page_pool_refill_alloc_cache will always
refill page once whether refill is true or false, and whether
alloc.count of pool is less than PP_ALLOC_CACHE_REFILL or not
this is wrong, and will cause overflow of pool->alloc.cache

the caller of __page_pool_get_cached should provide guarantee
that pool->alloc.cache is safe to access, so in_serving_softirq
should be removed as suggested by Jesper Dangaard Brouer in
https://patchwork.ozlabs.org/patch/1233713/

so fix this issue by calling page_pool_refill_alloc_cache()
only when pool->alloc.count is zero

Fixes: 44768dec ("page_pool: handle page recycle for NUMA_NO_NODE condition")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>