- 28 Nov, 2014 7 commits
-
-
Arnd Bergmann authored
Merge tag 'sirf-dts-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux into next/dt Pull "change pinmux pingroup and add some lost node/prop" from Barry Song: 1. add resets properity for some nodes; 2. change pinctrl groups for audio 3. add PMU node * tag 'sirf-dts-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux: ARM: dts: atlas6: add resets property for SPI nodes ARM: dts: atlas6: add resets property for VPP nodes ARM: dts: prima2: add resets property for VPP nodes ARM: dts: prima2: add resets property for GPS nodes ARM: dts: prima2: add node for Performance Monitor Unit ARM: dts: atlas6: Add I2S external clock input pingroup ARM: dts: atlas6: add a separate pingroup for i2s mclk output ARM: dts: prima2: add I2S 2ch, 6ch, nodin, mclk groups Signed-off-by:
Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt Pull "Allwinner simple frambuffer support" from Maxime Ripard: This enables the simple framebuffer on all the supported Allwinner SoCs (but the A80). That allows to have at last a video display usable by using the framebuffer the firmware might have set up. * tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (55 commits) ARM: dts: sunxi: Update simplefb nodes so that u-boot can find them ARM: dts: sunxi: Add de_be0 clk parent pll to simplefb node ARM: dts: sun7i: Add simplefb node ARM: dts: sun6i: Add simplefb node ARM: dts: sun5i: Add simplefb node ARM: dts: sun4i: Add simplefb node ARM: dts: sun6i: Add ethernet support to M9 board ARM: sun6i: DT: Add PLL6 multiple outputs ARM: dts: sun6i: Add support for the status led ARM: dts: sun6i: Add EHCI support for the M9 board ARM: dts: sunxi: Add regulator-boot-on property to ahci-5v regulator ARM: dts: sun7i: Cubietruck: add power supply regulator for USB OTG VBUS ARM: dts: sun7i: Cubietruck: override regulator pin ARM: sun7i: dtsi: add support for usbphy0 ARM: dtsi: sunxi: add common VBUS regulator ARM: dts: sunxi: Banana Pi: increase startup-delay for the GMAC PHY regulator ARM: sun5i: olinuxino: Relicense the device tree under GPLv2/X11 ARM: sun4i: cubieboard: Relicense the device tree under GPLv2/X11 ARM: sun7i: pcduino3: Relicense the device tree under GPLv2/X11 ARM: sun4i: pcduino: Relicense the device tree under GPLv2/X11 ... Signed-off-by:
-
Arnd Bergmann authored
Merge tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt Pull "The i.MX device tree changes for 3.19" from Shawn Guo: - Device additions for board vf610-colibri, pwm, backlight, I2C, RTC, ADC etc. - Update i.MX6 phyFLEX board to include PCIe, CAN and audio support - Improve SSI clocks description for i.MX5 platforms - Add ENET2 support for imx6sx-sdb board - Add device tree source for LS1021A SoC, board QDS and TWR - Enable cpufreq support for i.MX53 - Enable VPU device support for i.MX6QDL - Enable poweroff support for i.MX6 SoCs - Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q - Create generic base device trees for Vybrid and add support for Colibri VF50 Note: the change set is built on top of imx-soc-3.19 to resolve the dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM clock". * tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (51 commits) ARM: dts: imx6q-tbs2910: Enable snvs-poweroff ARM: dts: imx6: add pm_power_off support for i.mx6 chips ARM: dts: vf-colibri: add USB regulators ARM: dts: imx6: phyFLEX: Add CAN support ARM: dts: imx6: phyFLEX: Add PCIe ARM: dts: imx6: phyFLEX: Set correct interrupt for pmic ARM: dts: imx6: phyFLEX: Enable gpmi in module file ARM: dts: imx6: phyFLEX: set nodes in alphabetical order ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTC ARM: dts: vf-colibri: Add I2C support ARM: dts: imx6qdl: Enable CODA960 VPU ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' property ARM: dts: vf610: enable USB misc/phy nodes where necessary ARM: dts: vf610: use new GPIO support ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boards ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02 ARM: dts: vf500-colibri: add Colibri VF50 support ARM: dts: vf610: create generic base device trees ARM: dts: vf610: assign oscillator to clock module dt-bindings: arm: add Freescale LS1021A SoC device tree binding ... Signed-off-by; Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'omap-for-v3.19/dt-part2-updated' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt Pull "More dts changes for omaps to add support for new devices" from Tony Lindgren: - Add DCAN support am335x, am437x and dra7 - Add devices for sb-t3x computers - Add support for NovaTech OrionLXm - Add n900 battery and si4713 support * tag 'omap-for-v3.19/dt-part2-updated' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits) ARM: dts: am335x-evm: Add DCAN1 details ARM: dts: am33xx: Update DCAN nodes ARM: dts: am33xx: Add control module syscon node ARM: dts: am437x-gp: Add dcan support ARM: dts: am4372: Add DCAN nodes ARM: dts: am4372: Add control module syscon node ARM: dts: dra72-evm: Add CAN support ARM: dts: dra7-evm: Add CAN support ARM: dts: DRA7: Add DCAN nodes ARM: dts: dra7: Add syscon regmap for CORE CONTROL area ARM: dts: sbc-t3x30: add audio support ARM: dts: sbc-t3x: add TV out display alias ARM: dts: cm-t3x: add TV out support ARM: dts: cm-t3x: add I2C1 pinmux ARM: dts: AM43xx: add tscadc DT entries for am437x-evm and am43x-epos-evm ARM: dts: cm-t3x30: add keypad support ARM: dts: sb-t35: add EEPROM support ARM: dts: cm-t3x: add EEPROM support ARM: OMAP2+: remove cm-t3x touchscreen pdata quirk ARM: dts: cm-t3x: add ADS7846 touchscreen support ... Signed-off-by:
-
Arnd Bergmann authored
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt Pull "Samsung 3rd DT updates for v3.19" from Kukjin Kim: - exynos3250 : remove unused bootargs on exynos3250-rinato : add new board dt file for exynos3250-monk - exynos4 : add missing clock for MFC : specify default clocks for camera - exynos4x12 : add TMU related DT nodes - exynos4412-trats2 : add max77693-haptic and pwm nodes, enable TMU support - exynos4412-odroid : specify audio clock parents and rates - exynos5250 and exynos5420 : add syscon based phandle to i2c device nodes - exynos5250-spring : add trackpad, temperature sensor and usb3505 pinctrl Note: based on previous tags/samsung-dt-2 for v3.19 * tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: dts: add sysreg phandle to i2c device nodes for exynos ARM: dts: Remove unused bootargs from exynos3250-rinato ARM: dts: add board dts file for Exynos3250-based Monk board Documentation: devicetree: Add Exynos-based boards compatible string ARM: dts: add missing clock to MFC device for exynos4 ARM: dts: Specify audio clock parents and rates for exynos4412-odroid-common ARM: dts: Add trackpad to exynos5250-spring ARM: dts: Add temperature sensor to exynos5250-spring ARM: dts: Add usb3503 pinctrl to exynos5250-spring ARM: dts: Add max77693-haptic node for exynos4412-trats2 ARM: dts: add pwm node for exynos4412-trats2 ARM: dts: Specify default clocks for Exynos4 camera devices ARM: dts: Enable TMU support for exynos4412-trats2 ARM: dts: Device tree node definition for TMU on exynos4x12 Signed-off-by:
-
Arnd Bergmann authored
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt Pull "Samsung 2nd DT updates for v3.19" from Kukjin Kim: - add micro SD card SDHCI node for exynos4412-trats - add exynos4415 DT - add exynos3250-rinato DT and sleep mode support Note: based on previous tags/samsung-dt for v3.19 * tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: dts: Add micro SD card SDHCI node for exynos4412-trats ARM: dts: Add dts files for exynos4415 SoC ARM: dts: Add sleep mode of regulator for exynos3250-rinato ARM: dts: Add sleep mode pin configuration for exynos3250-rinato ARM: dts: Add board dts file for exynos3250-rinato Signed-off-by:
-
Arnd Bergmann authored
Merge tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt Pull "temporarily disable rk3288-smp" from Heiko Stuebner: Disable smp again on rk3288 temporarily to make Olof's boottest run again, until the patches for using the physical architected timers got accepted. * tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: ARM: dts: rockchip: temporarily disable smp on rk3288 Signed-off-by:
-
- 27 Nov, 2014 1 commit
-
-
Arnd Bergmann authored
This avoids a boot regression * sunxi/dt: Revert "ARM: dts: sunxi: unify APB1 clock" Revert "ARM: dts: sunxi: Use sun4i-a10-apb1-clk for sun6i/sun8i apb2 clocks." Signed-off-by:
-
- 26 Nov, 2014 4 commits
-
-
Pankaj Dubey authored
This patch adds syscon based phandle to i2c device nodes of exynos5250 and exynos5420. These phandles will be used to save restore i2c sysreg configuration register during s2r from i2c driver. CC: Rob Herring <robh+dt@kernel.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Russell King <linux@arm.linux.org.uk> CC: devicetree@vger.kernel.org CC: linux-doc@vger.kernel.org Signed-off-by:
Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Chanwoo Choi authored
This patch removes unused dt node of command line from Exynos3250-based Rinato board because kernel use the command line from bootloader. Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
-
Youngjun Cho authored
This patch adds new board dts file to support Samsung Monk board which is based on Exynos3250 SoC and has different H/W configuration from Rinato. This dts file support following features: - eMMC - Main PMIC (Samsung S2MPS14) - Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger) - RTC of Exynos3250 - ADC of Exynos3250 with NTC thermistor - I2S of Exynos3250 - TMU of Exynos3250 - Secure firmware for Exynos3250 secondary cpu boot - Serial ports of Exynos3250 - gpio-key for power key Signed-off-by:
Youngjun Cho <yj44.cho@samsung.com> Signed-off-by:
Inki Dae <inki.dae@samsung.com> Signed-off-by:
Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Chanwoo Choi authored
This patch adds the missing compatible/description of Exynos-based boards to remove following build warning. WARNING: DT compatible string "samsung,..." appears un-documented -- check ./Documentation/devicetree/bindings/ Signed-off-by:
-
- 25 Nov, 2014 8 commits
-
-
Qipan Li authored
this patch adds missed resets property for CSR SiRFatlasVI SPI nodes. Signed-off-by:
Qipan Li <Qipan.Li@csr.com> Signed-off-by:
Barry Song <Baohua.Song@csr.com>
-
Renwei Wu authored
this patch adds missed resets property for CSR SiRFatlasVI Video Post Processor(VPP) node. Signed-off-by:
Renwei Wu <renwei.wu@csr.com> Signed-off-by:
-
Renwei Wu authored
this patch adds missed resets property for CSR SiRFprimaII Video Post Processor(VPP) node. Signed-off-by:
-
Tao Huang authored
this patch adds missed resets property for CSR SiRFprimaII GPS related nodes. Signed-off-by:
Tao Huang <Tao.Huang@csr.com> Signed-off-by:
-
Ye He authored
It enables Performance Monitor Unit on CSR SiRFprimaII. Signed-off-by:
Ye He <ye.he@csr.com> Signed-off-by:
-
Rongjun Ying authored
The I2S controller can use the external clock as reference clock with master mode. But based on different hardware or software design, this external clock might be needed or not needed. So the external input pin can be an independent pinctrl group, and the card driver can decice to get it or not. Signed-off-by:
Rongjun Ying <rongjun.ying@csr.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
Rongjun Ying authored
The I2S controller can output mclk to external audio codec. But by hardware design, some codecs need mclk and some codecs do not need mclk. So the mclk pin can be an independent pinctrl group, and the card driver can get it or not based on boards. Signed-off-by:
-
Rongjun Ying authored
we have done that for atlas6 in commit ed36c1a0, 086b8904 etc. here we do same things for prima2. Signed-off-by:
-
- 24 Nov, 2014 16 commits
-
-
Arnd Bergmann authored
This reverts commit e883d672. Signed-off-by:
-
Arnd Bergmann authored
This reverts commit 338302ae. This is one of two commits that resulted in a boot regression. Conflicts: arch/arm/boot/dts/sun6i-a31.dtsi Signed-off-by:
-
Roger Quadros authored
DCAN1 is routed to CAN port (J11) when Profile 1 is selected on the profile selection switch. Provide information for DCAN1 pins and node but keep it disabled by default. User has to manually enable it if Profile 1 is chosen. Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Roger Quadros authored
Add "raminit-syscon" property to specify the RAMINIT register. Add clock information. Rename can nodes from "d_can" to "can" to be compliant with the ePAPR specs. Signed-off-by:
-
Roger Quadros authored
Use syscon regmap to expose the Control module register space. This register space is shared between many users e.g. DCAN, USB, display, etc. Signed-off-by:
-
Mugunthan V N authored
Add DCAN support for AM437x GP EVM with both DCAN instances. [Roger Q] Updated output pin to not use pull up. Signed-off-by:
Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by:
George Cherian <george.cherian@ti.com> Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
-
Roger Quadros authored
The SoC contains 2 DCAN modules. Add them. Signed-off-by:
-
Roger Quadros authored
Use syscon regmap to expose the Control module register space. This register space is shared between many users e.g. DCAN, USB, display, etc. Signed-off-by:
-
Roger Quadros authored
The board has 2 CAN ports but only the first one can be used. Enable the first CAN port. WAKEUP0 pin doesn't have INPUT enable bit so we just disable weak PULLs. The second CAN port cannot be used without hardware modification so we don't enable the second port. Signed-off-by:
-
Roger Quadros authored
The board has 2 CAN ports but only the first one can be used. Enable the first CAN port. WAKEUP0 pin doesn't have INPUT enable bit so we just disable weak PULLs. The second CAN port cannot be used without hardware modification so we don't enable the second port. Signed-off-by:
-
Roger Quadros authored
The SoC supports 2 DCAN nodes. Add them. Signed-off-by:
-
Roger Quadros authored
Display and DCAN drivers use syscon regmap to access some registers in the CORE control area. Add the syscon regmap node for this area. Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Nishanth Menon <nm@ti.com> Signed-off-by:
-
Dmitry Lifshitz authored
Add audio related DT nodes Signed-off-by:
Dmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by:
-
Dmitry Lifshitz authored
Add display alias for TV out. Signed-off-by:
-
Dmitry Lifshitz authored
Add TV out support. Signed-off-by:
-
Dmitry Lifshitz authored
Add missing I2C1 pinmux setup. Signed-off-by:
-
- 23 Nov, 2014 4 commits
-
-
Hans de Goede authored
Review of the u-boot sunxi simplefb patches has led to the decision that u-boot should not use a specific path to find the nodes as this goes contrary to how devicetree usually works. Instead a platform specific compatible + properties should be used for this. The simplefb bindings have already been updated to reflect this, this patch brings the sunxi devicetree files in line with the new binding, and the actual u-boot implementation as it is going upstream. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com>
-
Hans de Goede authored
Avoid the parent pll for the mod-clk for de_be0 getting disabled when non of the other users are enabled (which can happen when none of i2c, spi and mmc are in use). Note for now we point directly to the parent rather then to the de_be0 mod-clk as that is not modelled in our devicetree yet. Signed-off-by:
-
Hans de Goede authored
Add a simplefb template node for u-boot to further fill and activate. Signed-off-by:
-
Hans de Goede authored
Add a simplefb template node for u-boot to further fill and activate. Signed-off-by:
-
