- 28 Apr, 2010 11 commits
-
-
Dan Williams authored
The 'ready' condition was incorrectly evaluated which sometimes lead to failures loading the second-stage firmware on 8686 devices. (This was introduced in "libertas: consolidate SDIO firmware wait code". -- JWL) Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 27 Apr, 2010 26 commits
-
-
Shanyu Zhao authored
Currently whenever rts thresold is set, every packet will use RTS protection no matter its size exceeds the threshold or not. This is due to a bug in the rts threshold check. if (len > tx->local->hw.wiphy->rts_threshold) { txrc.rts = rts = true; } Basically it is comparing an int (len) and a u32 (rts_threshold), and the variable len is assigned as: len = min_t(int, tx->skb->len + FCS_LEN, tx->local->hw.wiphy->frag_threshold); However, when frag_threshold is "-1", len is always "-1", which is 0xffffffff therefore rts is always set to true. CC: stable@kernel.org Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
When scanning, it is somewhat important to scan on the correct virtual interface. All drivers that currently implement hw_scan only support a single virtual interface, but that may change and then we'd want to be ready. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
Now that the mac80211 is choosing dynamic ps timeouts based on the ps-qos network latency configuration, configure a default value of -1 as the dynamic ps timeout in cfg80211. This value allows the mac80211 to determine the value to be used. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
Determine the dynamic PS timeout based on the configured ps-qos network latency. For backwards wext compatibility, allow the dynamic PS timeout configured by the cfg80211 to overrule the automatically determined value. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
If bit 29 is set, MAC H/W can attempt to decrypt the received aggregate with WEP or TKIP, eventhough the received frame may be a CRC failed corrupted frame. If this bit is set, H/W obeys key type in keycache. If it is not set and if the key type in keycache is neither open nor AES, H/W forces key type to be open. But bit 29 should be set to 1 for AsyncFIFO feature to encrypt/decrypt the aggregate with WEP or TKIP. Cc: stable@kernel.org Reported-by: Johan Hovold <johan.hovold@lundinova.se> Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: Ranga Rao Ravuri <ranga.ravuri@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
This is used to configure APs to not bridge traffic between connected stations. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
TX interrupt mitigation reduces the number of interrupts by addressing several interrupt actions (AR_IMR_TXOK, AR_IMR_TXDESC) all in one interrupt so when enabling it discard setting the other interrupts. Without this TX interrupt mitigation would actually increase the number of interrupts two-fold. We still leave TX interrupt mitigation disabled as it is still being tested. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
When the noisefloor calibration times out, do not load -50 into the registers, since this might cause rx issues. Instead, leave enough time for the noise floor calibration to complete until the next check. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Since the new AR9003 EEPROM code does tune the card for the configured tx power level, we need to fill in the correct power limits in the TPC part of the DMA descriptor. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Combine multiple checks that were supposed to check for the same conditions, but didn't. Always enable fast PLL clock on AR9280 2.0 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Adds read access for the 5 GHz fast clock flag Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vasanthakumar Thiagarajan authored
Fast clock operation (44Mhz) is enabled for 5Ghz in ar9003, so take care of the conversion from usec to hw clock. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
Disable TX IQ calibration, it was prematurely enabled in previous versions. Cc: Paul Shaw <Paul.Shaw@Atheros.com> Cc: Thomas Hammel <Thomas.Hammel@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
This synchs up the initvals to the values used on the Atheros HAL for AR9003. This specific change adds support for a new high power module. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
A misplaced interface type check bails out too early if the interface is not in monitor mode. This patch moves it to the right place, so that it only covers changes to the monitor flags. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
A bunch of validation and processing in the RX IRQ handler can be moved to the RX tasklet. The IRQ handler is already heavy, with the memory allocation for handling stream mode. Also, a memcpy of 40 bytes for every packet can be avoided in the handler. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Check for the endpoint IDs when processing TX completions and drop the unsupported EPIDs. We can add other endpoints (UAPSD,..) when support is added. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 26 Apr, 2010 3 commits
-
-
Steve deRosier authored
Add the same type of configurable debug messages to libertas_tf as already exist in the libertas driver. This has facilitated creation of a interface specification and will facilitate future development of this driver. Signed-off-by: Steve deRosier <steve@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Remove redundant check for RT2872. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Restore the rfcsr initialization for RT305x SoC devices which was removed by "rt2x00: Finish rt3070 support in rt2800 register initialization.". This fixes the rx path on SoC devices. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-