- 04 May, 2020 33 commits
-
-
David S. Miller authored
Heiner Kallweit says: ==================== net: add helper eth_hw_addr_crc Several drivers use the same code as basis for filter hashes. Therefore let's factor it out to a helper. This way drivers don't have to access struct netdev_hw_addr internals. First user is r8169. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Use new helper eth_hw_addr_crc to simplify the code. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
Several drivers use the same code as basis for filter hashes. Therefore let's factor it out to a helper. This way drivers don't have to access struct netdev_hw_addr internals. Signed-off-by:
-
Michael Walle authored
If there is no specific configuration of the felix switch in the device tree, but only the default configuration (ie. given by the SoCs dtsi file), the probe fails because no CPU port has been set. On the other hand you cannot set a default CPU port because that depends on the actual board using the switch. [ 2.701300] DSA: tree 0 has no CPU port [ 2.705167] mscc_felix 0000:00:00.5: Failed to register DSA switch: -22 [ 2.711844] mscc_felix: probe of 0000:00:00.5 failed with error -22 Thus let the device tree disable this device entirely, like it is also done with the enetc driver of the same SoC. Signed-off-by:
Michael Walle <michael@walle.cc> Reviewed-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
David S. Miller authored
Karsten Graul says: ==================== net/smc: add failover processing This patch series adds the actual SMC-R link failover processing and improved link group termination. There will be one more (very small) series after this which will complete the SMC-R link failover support. ==================== Signed-off-by: -
Karsten Graul authored
During SMC-R link establishment the peers exchange the link_uid that is used for debugging purposes. Save the peer link_uid in smc_link so it can be retrieved by the smc_diag netlink interface. Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Reviewed-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
-
Karsten Graul authored
The link_uid of an SMC-R link is exchanged between SMC peers and its value can be used for debugging purposes. Create a unique link_uid during link initialization and use it in communication with SMC-R peers. Signed-off-by:
-
Karsten Graul authored
Add helper smcr_lgr_link_deactivate_all() and eliminate duplicate code. In smc_lgr_free(), clear the smc-r links before smc_lgr_free_bufs() is called so buffers are already prepared for free. The usage of the soft parameter in __smc_lgr_terminate() is no longer needed, smc_lgr_free() can be called directly. smc_lgr_terminate_sched() and smc_smcd_terminate() set lgr->freeing to indicate that the link group will be freed soon to avoid unnecessary schedules of the free worker. Signed-off-by:
-
Karsten Graul authored
Allow to set the reason code for the link group termination, and set meaningful values before termination processing is triggered. This reason code is sent to the peer in the final delete link message. When the LLC request or response layer receives a message type that was not handled, drop a warning and terminate the link group. Signed-off-by:
-
Karsten Graul authored
New connections must not be assigned to asymmetric links. Add asymmetric link tagging using new link variable link_is_asym. The new helpers smcr_lgr_set_type() and smcr_lgr_set_type_asym() are called to set the state of the link group, and tag all links accordingly. smcr_lgr_conn_assign_link() respects the link tagging and will not assign new connections to links tagged as asymmetric link. Signed-off-by:
-
Karsten Graul authored
For new connections, assign a link from the link group, using some simple load balancing. Signed-off-by:
-
Karsten Graul authored
Add smc_llc_send_message_wait() which uses smc_wr_tx_send_wait() to send an LLC message and waits for the message send to complete. smc_llc_send_link_delete_all() calls the new function to send an DELETE_LINK,ALL LLC message. The RFC states that the sender of this type of message needs to wait for the completion event of the message transmission and can terminate the link afterwards. Signed-off-by:
-
Karsten Graul authored
Introduce smc_wr_tx_send_wait() to send an IB message and wait for the tx completion event of the message. This makes sure that the message is no longer in-flight when the function returns. Signed-off-by:
-
Karsten Graul authored
Call smc_cdc_msg_validate() when a CDC message with the failover validation bit enabled was received. Validate that the sequence number sent with the message is one we already have received. If not, messages were lost and the connection is terminated using a new abort_work. Signed-off-by:
-
Karsten Graul authored
When a connection is switched to a new link then a link validation message must be sent to the peer over the new link, containing the sequence number of the last CDC message that was sent over the old link. The peer will validate if this sequence number is the same or lower then the number he received, and abort the connection if messages were lost. Add smcr_cdc_msg_send_validation() to send the message validation message and call it when a connection was switched in smc_switch_cursor(). Signed-off-by:
-
Karsten Graul authored
Add smc_switch_conns() to switch all connections from a link that is going down. Find an other link to switch the connections to, and switch each connection to the new link. smc_switch_cursor() updates the cursors of a connection to the state of the last successfully sent CDC message. When there is no link to switch to, terminate the link group. Call smc_switch_conns() when a link is going down. And with the possibility that links of connections can switch adapt CDC and TX functions to detect and handle link switches. Signed-off-by:
-
Karsten Graul authored
When a link goes down and all connections of this link need to be switched to an other link then the producer cursor and the sequence of the last successfully sent CDC message must be known. Add the two fields to the SMC connection and update it in the tx completion handler. And to allow matching of sequences in error cases reset the seqno to the old value in smc_cdc_msg_send() when the actual send failed. Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Updates for net-next. This patchset includes these main changes: 1. Firmware spec. update. 2. Context memory sizing improvements for the hardware TQM block. 3. ethtool chip reset improvements and fixes for correctness. 4. Improve L2 doorbell mapping by mapping only up to the size specified by firmware. This allows the RoCE driver to map the remaining doorbell space for its purpose, such as write-combining. 5. Improve ethtool -S channel statistics by showing only relevant ring counters for non-combined channels. ==================== Signed-off-by: -
Rajesh Ravi authored
Currently, ethtool -S shows all TX/RX ring counters whether the channel is combined, RX, or TX. The unused counters will always be zero. Improve it by showing only the relevant counters if the channel is RX or TX. If the channel is combined, the counters will be shown exactly the same as before. [ MChan: Lots of cleanups and simplifications on Rajesh's original code] Signed-off-by:
Rajesh Ravi <rajesh.ravi@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Michael Chan authored
This will allow the RX and TX ring statistics to be separated if needed. In the next patch, we'll be able to only display RX or TX statistcis if the channel is RX only or TX only. Signed-off-by:
-
Michael Chan authored
We currently have 3 software ring counters, rx_l4_csum_errors, rx_buf_errors, and missed_irqs. The 1st two are RX counters and the last one is a common counter. Organize them into 2 structures bnxt_rx_sw_stats and bnxt_cmn_sw_stats. Signed-off-by:
-
Michael Chan authored
The purpose of this is to inform the RDMA driver the size of the doorbell BAR that the L2 driver has mapped and the portion that is mapped uncacheable. The unchaeable portion is shared with the RoCE driver. Any remaining unmapped doorbell BAR can be used by the RDMA driver for its own purpose. Currently, the entire L2 portion is mapped uncacheable. Signed-off-by:
-
Michael Chan authored
Read the L2 doorbell size from the firmware and only map the portion of the doorbell BAR for L2 use. This will leave the remaining doorbell BAR available for the RoCE driver to use. The RoCE driver can map the remaining portion as write-combining to support the push feature. Signed-off-by:
-
Michael Chan authored
The driver provides completion ring or NQ doorbell offset for each MSIX entry requested by the RDMA driver. The NQ offset on 57500 chips is different than legacy chips. Set it correctly based on chip type for correctness. The RDMA driver is ignoring this field for the 57500 chips so it is not causing any problem. Signed-off-by:
-
Michael Chan authored
Define the 57500 chip doorbell offsets instead of using the magic values in the C file. Signed-off-by:
-
Edwin Peer authored
Kernel log messages for failed AP reset commands should be suppressed. These are expected to fail on devices that do not have an AP. Add missing driver reload message after AP reset and log it in a common way without duplication. Signed-off-by:
Edwin Peer <edwin.peer@broadcom.com> Signed-off-by:
-
Edwin Peer authored
The ethtool ABI specifies that the reset operation should only clear the flags that were actually reset. Setting the flags to zero after a chip reset violates this because it does not include resetting the application processor complex. Similarly, components that are not yet defined are also not necessarily being reset. The fact that chip reset does not cover the AP also means that it is inappropriate to treat these two components exclusively of one another. The ABI provides a mechanism to report a failure to reset independent components via the returned bitmask, so it is also wrong to fail hard if one of a set of independent resets is not possible. It is incorrect to rely on the passed by reference flags in bnxt_reset(), which are being updated as components are reset. The initially requested value should be used instead so that hard errors do not propagate if any earlier components could have been reset successfully. Note, AP and chip resets are global in nature. Dedicated resets are thus not currently supported. Signed-off-by:
-
Edwin Peer authored
The case statement in bnxt_firmware_reset() dangerously mixes types. This patch separates the application processor and whole chip resets from the rest such that the selection is performed on a pure type. Signed-off-by:
-
Edwin Peer authored
Extract bnxt_hwrm_firmware_reset() for performing firmware reset operations. This new helper function will be used in a subsequent patch to separate unrelated reset types out of bnxt_firmware_reset(). Signed-off-by:
-
Vasundhara Volam authored
The firmware does not expect the CRC to be included in the length passed from the driver. The firmware always configures the chip to strip out the CRC. Signed-off-by:
Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by:
-
Michael Chan authored
The current formulas to calculate the TQM slow path and fast path ring context memory sizes are not quite correct. TQM slow path entry is array index 0 of ctx->tqm_mem[]. The other array entries are for fast path. Fix these sizes according to latest firmware spec. for 57500 and newer chips. Fixes: 3be8136c ("bnxt_en: Initialize context memory to the value specified by firmware.") Signed-off-by:
-
Michael Chan authored
Newer firmware spec. will specify the number of TQM rings to allocate context memory for. Use the firmware specified value and fall back to the old value derived from bp->max_q if it is not available. Signed-off-by:
-
Michael Chan authored
Changes include additional statistics, ECN support, context memory interface change for better TQM context memory sizing, firmware health status definitions, etc. Signed-off-by:
-
- 03 May, 2020 7 commits
-
-
David S. Miller authored
Karsten Graul says: ==================== net/smc: add and delete link processing These patches add the 'add link' and 'delete link' processing as SMC server and client. This processing allows to establish and remove links of a link group dynamically. v2: Fix mess up with unused static functions. Merge patch 8 into patch 4. Postpone patch 13 to next series. ==================== Signed-off-by: -
Karsten Graul authored
As SMC server, when a second link was deleted, trigger the setup of an asymmetric link. Do this by enqueueing a local ADD_LINK message which is processed by the LLC layer as if it were received from peer. Do the same when a new IB port became active and a new link could be created. smc_llc_srv_add_link_local() enqueues a local ADD_LINK message. And smc_llc_srv_delete_link_local() is used the same way to enqueue a local DELETE_LINK message. This is used when an IB port is no longer active. Signed-off-by:
-
Karsten Graul authored
Add smc_llc_process_srv_delete_link() to process a DELETE_LINK request as SMC server. When the request is to delete ALL links then terminate the whole link group. If not, find the link to delete by its link_id, send the DELETE_LINK request LLC message and wait for the response. No matter if a response was received, clear the deleted link and update the link group state. Signed-off-by:
-
Karsten Graul authored
Add smc_llc_process_cli_delete_link() to process a DELETE_LINK request as SMC client. When the request is to delete ALL links then terminate the whole link group. If not, find the link to delete by its link_id, send the DELETE_LINK response LLC message and then clear the deleted link. Finally determine and update the link group state. Signed-off-by:
-
Karsten Graul authored
Introduce a work that is scheduled when a new DELETE_LINK LLC request is received. The work will call either the SMC client or SMC server DELETE_LINK processing. And use the LLC flow framework to process incoming DELETE_LINK LLC messages, scheduling the llc_del_link_work for those events. With these changes smc_lgr_forget() is only called by one function and can be migrated into smc_lgr_cleanup_early(). Signed-off-by:
-
Karsten Graul authored
When a link group moved from asymmetric to symmetric state then the dangling asymmetric link can be deleted. Add smc_llc_find_asym_link() to find the respective link and add smc_llc_delete_asym_link() to delete it. Signed-off-by:
-
Karsten Graul authored
This patch finalizes the ADD_LINK processing of new links. Send the CONFIRM_LINK request to the peer, receive the response and set link state to ACTIVE. Signed-off-by:
-
