Use devm_* api to simplify code, this makes it unnecessary to explicitly
release resources.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230714080611.81302-2-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_* api to simplify code, this makes it unnecessary to explicitly
release resources.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230714080611.81302-1-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

MELFAS MMS114 and similar touchscreens have support for touch keys.
Enable support of them in the driver. The keycodes to emit can be
controlled by the linux,keycodes DT property.

Sidenote - the MAX_TOUCHKEYS value is set to 15, as that's the
maximum value that the ID field can contain. I don't have access
to any datasheets that could confirm or deny whether this is accurate.

Most downstream drivers I've been able to find only use up to 2 keys
(though I did find a driver that mentioned up to 4, but only 2 were
used). They don't have any checks for a maximum keycode value, it is
just extracted from the ID bits (0xf mask).

The drivers I've been able to find also don't use touch ID 0; I assume
that it is never used, so the keycodes provided in the DT start from
touch ID 1. I suppose this is in-line with the regular behavior
for touch IDs in touchscreen events, as there the provided touch ID
is always lowered by 1, which would cause an overflow if it was 0...
Just in case, we quietly return if the touch ID is set to 0 here.

The implementation of the linux,keycodes property handling code was
adapted from the msg2638 driver.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20230714100424.29798-3-aweber.kernel@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

MELFAS MMS114 and similar touchscreens have support for touch keys.
Add the linux,keycodes property which can be used to set up the
keycodes for the touch keys.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20230714100424.29798-2-aweber.kernel@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Mark the IRQ as a wake IRQ so it will be enabled during system suspend.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20230717192004.1304287-1-samuel.holland@sifive.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use the dev_err_probe() helper, instead of open-coding the same
operation.

While at it, invert the error checking logic to simplify code flow.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/d225a837c50e2b19a41555a8f7ce0f94b1689aa4.1689600353.git.geert+renesas@glider.beSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174633.4058096-1-robh@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync up with mainline to bring in updates to shared infrastructure.

Point the OF match table directly to the struct that describes the
device as opposed to an intermediate enum; doing so simplifies the
code and avoids a clang warning.

As part of this change, the I2C device ID table is removed, as the
device cannot probe without an OF node due to the unique nature of
the hardware's interrupt pin.

Fixes: f2ba47e6 ("Input: add support for Azoteq IQS7210A/7211A/E")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307131717.LtwApG0z-lkp@intel.com/Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/ZLA+cuciIeVcCvm6@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for the Azoteq IQS7210A/7211A/E family of trackpad/
touchscreen controllers.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/ZHVEeDlYyr69A59K@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add bindings for the Azoteq IQS7210A/7211A/E family of trackpad/
touchscreen controllers.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/ZHVEa0yM1LLUJEfO@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

devm_input_allocate_device() already assigns the @dev.parent field of the
input device/structure, so there's no need to reassign input->dev.parent
to dev.
Signed-off-by: Roi L <roeilev321_@outlook.com>
Link: https://lore.kernel.org/r/PH0P220MB0460B69CA018F5515F5FACDDDD53A@PH0P220MB0460.NAMP220.PROD.OUTLOOK.COMSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pass proper PTR_ERR as dev_err_probe() argument.

Fixes: a2c795b6 ("Input: bcm-keypad - simplify with dev_err_probe()")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202306261505.wTjCXRIO-lkp@intel.com/Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230711072449.43569-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_* api to simplify code, this makes it unnecessary to explicitly
release resources.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705052346.39337-10-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_* api to simplify code, this makes it unnecessary to explicitly
release resources.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705052346.39337-8-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705052346.39337-7-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705052346.39337-6-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705052346.39337-5-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705052346.39337-4-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705052346.39337-3-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705052346.39337-2-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705052346.39337-1-frank.li@vivo.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The vendor has introduced a new variant of silicon which is highly
similar to the existing IQS7222A, but with its independent sliders
essentially replaced with a single-contact trackpad.

Update the common driver to support this new device's register map
and report trackpad events. As with the IQS7222A, the new IQS7222D
can report both raw coordinates as well as gestures.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/ZKrpRh6RT6+6KrMQ@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Extend the common binding to include a new variant of the silicon,
which effectively replaces a pair of slider nodes with a trackpad
node comprising the same or similar properties.

As part of this change, the if/then/else schema have been updated
to identify properties that are not supported by the new device.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/ZKrpOdp+rM8gDekw@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The units assumed by the 'azoteq,top-speed', 'azoteq,bottom-speed'
and 'azoteq,gesture-dist' properties are unspecified; define them
according to the device's datasheet.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/ZKrpMekZBt95Gmnr@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If the device drops into ultra-low-power mode before being placed
into normal-power mode as part of ATI being triggered, the device
does not assert any interrupts until the ATI routine is restarted
two seconds later.

Solve this problem by adopting the vendor's recommendation, which
calls for the device to be placed into normal-power mode prior to
being configured and ATI being triggered.

The original implementation followed this sequence, but the order
was inadvertently changed as part of the resolution of a separate
erratum.

Fixes: 1e4189d8 ("Input: iqs7222 - protect volatile registers")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/ZKrpHc2Ji9qR25r2@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

devm_platform_get_and_ioremap_resource maps a resource and returns its
physical address. If we don't need the physical address, we should call
devm_platform_ioremap_resource instead.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230709134109.182418-1-martin@kaiser.cxSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

A phoronix forum member actual found documentation on what the model
number for the touchscreen controller on the Acer Iconia One 7 B1-750 is.

Update the driver's description to include this.

Link: https://www.phoronix.com/forums/forum/hardware/general-hardware/1382535-10-years-later-linux-getting-a-touchscreen-driver-for-a-once-popular-tablet?p=1384707#post1384707Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230710123633.323937-2-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix input_register_device() failure logging "failed to request irq"
as error message.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230710123633.323937-1-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add a new property 'threshold' to the edt-ft5x06 touchscreen binding.
This property allows setting the "click"-threshold in the range from 0
to 255. This change addresses the following dtbs_check warning:
imx6dl-lanmcu.dtb: touchscreen@38: 'threshold' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230621093245.78130-6-o.rempel@pengutronix.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_regulator_get_enable() instead of hand writing it. It saves some
line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/af343b5b0d740cc9f8863264c30e3da4215721d7.1686985911.git.christophe.jaillet@wanadoo.frSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_regulator_get_enable() instead of hand writing it. It saves some
line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/78d7a4719ed7c372a7aa62afb66d4f1561799b5f.1686985515.git.christophe.jaillet@wanadoo.frSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

'dev' is shorter and simpler than '&client->dev' and in few cases it
allows to skip line wrapping. Probe function uses '&client->dev' a lot,
so this improves readability slightly.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230625162817.100397-25-krzysztof.kozlowski@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

'dev' is shorter and simpler than '&client->dev' and in few cases it
allows to skip line wrapping. Probe function uses '&client->dev' a lot,
so this improves readability slightly.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230625162817.100397-24-krzysztof.kozlowski@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe() and devm_clk_get_optional().  Less code and the error
value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230625162817.100397-23-krzysztof.kozlowski@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230625162817.100397-22-krzysztof.kozlowski@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230625162817.100397-21-krzysztof.kozlowski@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230625162817.100397-20-krzysztof.kozlowski@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230625162817.100397-19-krzysztof.kozlowski@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230625162817.100397-18-krzysztof.kozlowski@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>