The i2c driver can run into driver dependency issues if its loaded
before a clock driver it depends on. Therefore, EPROBE_DEFER may be
returned by devm_clk_get and should be returned in probe to allow the
kernel to reprobe the driver at a later time. This patch allows the error
value returned by devm_clk_get to be passed through and not overwritten.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add i2c compatible for MT7622. Compare to MT8173 i2c controller,
MT7622 limits message numbers to 255, and does not support 4GB
DMA mode.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add MT7622 i2c binding to binding file. Compare to MT8173 i2c
controller, MT7622 limits message numbers to 255, and does not
support 4GB DMA mode.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use common name MediaTek and modify the compatible information
formats of all SoCs to the same.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

It simplifies some tests.
Signed-off-by: Peter Rosin <peda@axentia.se>

Specifically mention what drivers are mux-locked and parent-locked.
Signed-off-by: Peter Rosin <peda@axentia.se>

The Cherry Trail Whiskey Cove PMIC's IRQ line is attached to one of
the GPIOs of the Cherry Trail SoC. The CHT GPIO controller sometimes
fails to deliver IRQs (seen when there is an IRQ storm on another pin).

This commit works around this by reducing the long timeout which was
a poor attempt to workaround this from 3s to 30ms and after that
manually checking the status register for transfer completion by
calling the threaded IRQ handler directly.

This is safe todo as the entire threaded IRQ handler is protected
by a mutex.

Note 30ms should be more then long enough, at 100KHz any smbus single
byte transaction should be finished in 4ms.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Testing has shown that writing 1 to clear the read-complete irq does
not work until the data register has been read first.

This commit fixes the driver to read the data register first, halving the
amount of interrupts in most cases since we mostly read on this i2c bus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Although unlikely without locking the smbux_xfer function may miss
the nack flag and further fixes in this patch-set add some more
complex constructions which need protection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Fix smatch warning:
drivers/i2c/busses/i2c-sh_mobile.c:564 \
  sh_mobile_i2c_request_dma_chan() warn: unused return: ret = PTR_ERR()
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Fix smatch warning:
drivers/i2c/busses/i2c-rcar.c:628 \
  rcar_i2c_request_dma_chan() warn: unused return: ret = PTR_ERR()
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If i2c_mux_alloc() fails then we'd have a NULL dereference here.

Fixes: c4aee3e1 ("i2c: mux: pinctrl: remove platform_data")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Rosin <peda@axentia.se>

24xx BMCs have larger clock divider granularity which can cause problems
when trying to set them as 25xx clock dividers; this adds clock setting
code specific to 24xx.

This also fixes a potential issue where clock dividers were rounded down
instead of up.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Commit a53e35db ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-i2c@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Commit a53e35db ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Commit a53e35db ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Commit a53e35db ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The information is available elsewhere.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Peter Rosin <peda@axentia.se>

No platform (at least no upstreamed platform) has ever used this
platform_data. Just drop it and simplify the code.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>

include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>

include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>

Make it consistent with the other drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>

The Intel Cherry Trail Whiskey Cove PMIC does not contain a builtin
battery charger, instead boards with this PMIC use an external TI
bq24292i charger IC, which is connected to a SMBUS controller built into
the PMIC.

This commit adds an i2c-bus driver for the PMIC's builtin SMBUS
controller. The probe function for this i2c-bus will also register an
i2c-client for the TI bq24292i charger after the i2c-bus has been
registered.

Note that several device-properties are set on the client-device to
tell the bq24190 power-supply driver to integrate the Whiskey Cove PMIC
and e.g. use the PMIC's BC1.2 detection (through extcon) to determine
the maximum input current.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>

Document i2c Device Tree support for RZ/G1[ME]
(also known as r8a774[35]) SoCs. They are compatible with
R-Car Gen2 SoC family. No driver change is required as the
initialisation sequence is currently the same as for the
R-Car Gen2 fallback binding.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Document i2c Device Tree support for RZ/G1[ME]
(also known as r8aA774[35]) SoCs. They are compatible with
R-Car Gen2 SoC family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Support for the i2c controller on rv1108 soc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add dt Document for i2c controller on rv1108
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Check for i2c_algorithm and i2c_adapter_quirks structures that are only
stored in the algo and quirks fields of an i2c_adapter structure
correspondingly. These fields are declared const, so i2c_algorithm and
i2c_adapter_quirks structures that have this property can be declared
as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for designware)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull x86 platform driver fix from Darren Hart:
 "Fix loop preventing some platforms from waking up via the power button
  in s2idle:

   - intel-vbtn: match power button on press rather than release"

* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: intel-vbtn: match power button on press rather than release

Pull ext4 fixes from Ted Ts'o:
 "A large number of ext4 bug fixes and cleanups for v4.13"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix copy paste error in ext4_swap_extents()
  ext4: fix overflow caused by missing cast in ext4_resize_fs()
  ext4, project: expand inode extra size if possible
  ext4: cleanup ext4_expand_extra_isize_ea()
  ext4: restructure ext4_expand_extra_isize
  ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
  ext4: make xattr inode reads faster
  ext4: inplace xattr block update fails to deduplicate blocks
  ext4: remove unused mode parameter
  ext4: fix warning about stack corruption
  ext4: fix dir_nlink behaviour
  ext4: silence array overflow warning
  ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
  ext4: release discard bio after sending discard commands
  ext4: convert swap_inode_data() over to use swap() on most of the fields
  ext4: error should be cleared if ea_inode isn't added to the cache
  ext4: Don't clear SGID when inheriting ACLs
  ext4: preserve i_mode if __ext4_set_acl() fails
  ext4: remove unused metadata accounting variables
  ext4: correct comment references to ext4_ext_direct_IO()

Pull MIPS fixes from Ralf Baechle:
 "This fixes two build issues for ralink platforms, both due to missing
  #includes which used to be included indirectly via other headers"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: mt7620: Add missing header
  MIPS: ralink: Fix build error due to missing header

The latest change of compat_sys_sigpending in commit 8f13621a
("sigpending(): move compat to native") has broken it in two ways.

First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.

Second, on big endian architectures these bytes are being written in the
wrong order.

This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes: 8f13621a ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This bug was found by a static code checker tool for copy paste
problems.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks.  This may
caused the superblock being corrupted with zero blocks count.

Fixes: 1c6bd717Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+