- 01 Jul, 2024 39 commits
-
-
Marek Olšák authored
Signed-off-by:
Marek Olšák <marek.olsak@amd.com> Acked-by:
Alex Deucher <alexander.deucher@amd.com> Reviewed-by:
Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by:
-
Marek Olšák authored
It used gfx9 flags, which has undefined behavior on gfx12. Signed-off-by:
-
Marek Olšák authored
All this code has undefined behavior on GFX12 and shouldn't be executed. Signed-off-by:
-
Marek Olšák authored
It verified GFX9-11 swizzle modes on GFX12, which has undefined behavior. Signed-off-by:
-
Hawking Zhang authored
Driver should write to fault_cntl registers to do one-shot address/status clear. Signed-off-by:
Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by:
Tao Zhou <tao.zhou1@amd.com> Signed-off-by:
-
Marek Olšák authored
It only uses fields for GFX9-11 related to the separate DCC buffer, which doesn't exist in GFX12. Signed-off-by:
-
Marek Olšák authored
Checking SWIZZLE_MODE has undefined behavior on gfx12. Signed-off-by:
-
Marek Olšák authored
They were added accidentally. Signed-off-by:
-
Marek Olšák authored
GDS doesn't exist in gfx12. The incomplete packet allows userspace to hang the hw from the kernel. Signed-off-by:
Christian König <christian.koenig@amd.com> Acked-by:
-
Marek Olšák authored
If any INV flags are needed, they should be executed via ACQUIRE_MEM before INDIRECT_BUFFER. GLM flags are also removed because the hw ignores them. Signed-off-by:
-
Marek Olšák authored
If any INV flags are needed, they should be executed via ACQUIRE_MEM before INDIRECT_BUFFER. Signed-off-by:
-
Marek Olšák authored
Fix incorrect check. Signed-off-by:
-
Aric Cyr authored
* FW Release 0.0.224.0 * Fix bw issue for dcn351 * Fix FAMS2 logic issue for dcn401 * Fix Coverity issues * Fix cursor issues * Refactor dio sources Acked-by:
Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by:
Jerry Zuo <jerry.zuo@amd.com> Signed-off-by:
Aric Cyr <aric.cyr@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
-
Roman Li authored
[Why] Potential out of bounds access in dml2_calculate_rq_and_dlg_params() because the value of out_lowest_state_idx used as an index for FCLKChangeSupport array can be greater than 1. [How] Currently dml2 core specifies identical values for all FCLKChangeSupport elements. Always use index 0 in the condition to avoid out of bounds access. Acked-by:
Roman Li <Roman.Li@amd.com> Tested-by:
-
Fangzhi Zuo authored
Fix 4k240 underflow on dcn351 Acked-by:
-
Tom Chung authored
[Why] Some of the panels does not have the refresh rate range info in base EDID and only have the refresh rate range info in DisplayID block. It will cause the max/min freesync refresh rate set to 0. [How] Try to parse the refresh rate range info from DisplayID if the max/min refresh rate is 0. Reviewed-by:
Sun peng Li <sunpeng.li@amd.com> Signed-off-by:
Tom Chung <chiahsuan.chung@amd.com> Tested-by:
-
Xi (Alex) Liu authored
[Why] In OTG disable workarund, CRTC is disabled immediately to improve performance, but this may cause timing issue in DP HPO encoder FIFO and result in blank CRCs. [How] Replace the immediate CRTC disable call with normal disable call Reviewed-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by:
Xi (Alex) Liu <xi.liu@amd.com> Tested-by:
-
Bhuvanachandra Pinninti authored
[why] Refactor the code of dio to unit test. [how] Moved files to respective folders and changed cMakeLists and makefiles. Acked-by:
Bhuvanachandra Pinninti <bpinnint@amd.com> Tested-by:
-
Alvin Lee authored
[Description] We need to ensure to take into account cursor prefetch BW in mode support or we may pass ModeQuery but fail an actual flip which will cause a hang. Flip may fail because the cursor_pre_bw is populated during mode programming (and mode programming is never called prior to ModeQuery). Reviewed-by:
Chaitanya Dhere <chaitanya.dhere@amd.com> Reviewed-by:
Nevenko Stupar <nevenko.stupar@amd.com> Signed-off-by:
Alvin Lee <alvin.lee2@amd.com> Tested-by:
-
Wenjing Liu authored
[why] The function enumerates all pipes without checking pipe type. It is only supposed to call program pixel clock for OTG master pipe only. Reviewed-by:
Wenjing Liu <wenjing.liu@amd.com> Tested-by:
-
Fangzhi Zuo authored
Reset fams stream count upon stream removal, otherwise fams2 state machine in dmub will get corrupted. Reviewed-by:
Dillon Varone <dillon.varone@amd.com> Signed-off-by:
-
Nicholas Kazlauskas authored
[Why] DM can hook this up to disable SLDO optimizations in firmware during DMCUB initialization for debug purposes. [How] Add the option and pass it through dmub_srv. Reviewed-by:
Hansen Dsouza <hansen.dsouza@amd.com> Signed-off-by:
-
Paul Hsieh authored
[Why] Driver doesn't validate multi-display with scaling when OS calls DDI. This behavior causes the validated result to be a mismatch between some automated test cases. To address this issue, some workaround was added that caused issues in 8k. [How] Since the origin issue had been root caused, revert the previous workaround and unblock 8k with a single dimm. Reviewed-by:
Paul Hsieh <paul.hsieh@amd.com> Tested-by:
-
Ryan Seto authored
[Why] Audio for 8K 240Hz monitor was not available when it should be [How] Added calculation based on stream state Co-developed-by:
Ryan Seto <ryanseto@amd.com> Reviewed-by:
George Shen <george.shen@amd.com> Signed-off-by:
-
Tom Chung authored
[Why] We only enable the VRR while monitor usable refresh rate range is greater than 10 Hz. But we did not check the range in DRM_EDID_FEATURE_CONTINUOUS_FREQ case. [How] Add a refresh rate range check before set the freesync_capable flag in DRM_EDID_FEATURE_CONTINUOUS_FREQ case. Reviewed-by:
Mario Limonciello <mario.limonciello@amd.com> Reviewed-by:
-
Dillon Varone authored
[WHY&HOW] Cleanup unnecessary code pathes as compile guards were added and removed overtime. Reviewed-by:
-
Alex Hung authored
[WHAT & HOW] A denominator cannot be 0, and is checked before used. This fixes 2 DIVIDE_BY_ZERO issues reported by Coverity. Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
Alex Hung <alex.hung@amd.com> Tested-by:
-
Alex Hung authored
[WHAT & HOW] A denominator cannot be 0, and is checked before used. This fixes 1 DIVIDE_BY_ZERO issue reported by Coverity. Reviewed-by:
-
Nevenko Stupar authored
[Why & How] When MPC enabled, need to adjust x and hot spot x position on one pipe when the cursor is between MPC slices i.e. when the cursor is moving from one MPC slice to next slice, while whole cursor size is not contained within one pipe, to make part of the cursor to be visible on the other pipe. Reviewed-by:
Sridevi Arvindekar <sridevi.arvindekar@amd.com> Signed-off-by:
-
Sherry Wang authored
[Why] We try to disable abm immediately when it's being gradually disabled, which causes backlight ramping being paused in the middle [How] Don't disable abm immediately if abm has been or is being disabled through set_abm_level path Reviewed-by:
Anthony Koo <anthony.koo@amd.com> Signed-off-by:
Sherry Wang <yao.wang1@amd.com> Tested-by:
-
Alex Hung authored
[WHAT & HOW] Integer multiplies integer may overflow in context that expects an expression of unsigned/siged long long (64 bits). This can be fixed by casting integer to unsigned/siged long long to force 64 bits results. This fixes 26 OVERFLOW_BEFORE_WIDEN issues reported by Coverity. Reviewed-by:
-
George Shen authored
[Why] Certain configurations of DCN401 require ODM4:1 to support DCC for 10K surfaces. DCC should be conservatively disabled in those cases. The issue is that current logic limits 10K surface DCC for all configurations of DCN401. [How] Add DC ASIC cap to indicate max surface width that can support DCC. Disable DCC if this ASIC cap is non-zero and surface width exceeds it. Reviewed-by:
Jun Lei <jun.lei@amd.com> Signed-off-by:
-
Teeger authored
This reverts commit 871512e3 due to multiple issues found. Reviewed-by:
Teeger <gateeger@amd.com> Tested-by:
-
Sung Joon Kim authored
[why] Previously, we decide on the unbounded request purely based on pipe_cnt which is a wrong variable to use to determine how many pipes are in "use". DML already accounts for number of pipes in use along with other various factors and is a more reliable method of determination. [how] Use UnboundedRequestEnabledThisState to decide on unbounbded_req_enabled. Reviewed-by:
Sung Joon Kim <sungjoon.kim@amd.com> Tested-by:
-
Joshua Aberback authored
[Why] This error message is unnecessary because returning when aconnector is uninitialized is the desired outcome during initialization. As well, there is no equivalent error message for read_dpcd. Reviewed-by:
Joshua Aberback <joshua.aberback@amd.com> Tested-by:
-
George Shen authored
[Why] Certain situations cause pipes to have a recout of 0, such as when the dst_rect lies completely outside of a given ODM slice. [How] Skip calculation that transforms cursor coordinates to viewport space. Reviewed-by:
-
Tom Chung authored
[Why] Sometimes the new_crtc_state->vrr_infopacket did not sync up with the current state. It will affect the update_freesync_state_on_stream() does not update the state correctly. [How] Reset the freesync config before get_freesync_config_for_crtc() to make sure we have the correct new_crtc_state for VRR. Reviewed-by:
-
Anthony Koo authored
- Add new Replay states 2A (initial Replay entry) and 4E (frame update) to check is there is new frame update before sending Acked-by:
-
Alex Deucher authored
This is a big structure so use vmalloc as malloc can fail when there is memory pressure. Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3454Reviewed-by:
-
- 27 Jun, 2024 1 commit
-
-
Mario Limonciello authored
Although designs may contain an ISP IP block, the camera might be a USB camera. Because of this the ISP firmware is considered optional from amdgpu. However if the firmware doesn't get loaded the hardware should not be initialized. Adjust the return code for early init to ensure the IP block doesn't go through the other init and fini sequences. Also decrease the message about firmware load failure to debug so it's not as alarming to users. Acked-by:
Pratap Nirujogi <pratap.nirujogi@amd.com> Signed-off-by:
-
