The driver doesn't check if the regulator_get_optional return value is
-EPROBE_DEFER so it will wrongly assume that the regulator couldn't be
found just because the regulator driver wasn't registered yet, i.e:

exynos-tmu 10060000.tmu: Regulator node (vtmu) not found

In this case the return value should be propagated to allow the driver
probe function to be deferred until the regulator driver is registered.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The Exynos TMU DT binding says that the vtmu-supply is optional but the
driver uses devm_regulator_get() that creates a dummy regulator if it's
not defined in the DT. For example the following message is in the log:

10060000.tmu supply vtmu not found, using dummy regulator

Use the optional version of regulator_get() that doesn't create a dummy
regulator and instead returns a -ENODEV errno code. Since it's expected
that a regulator may not be defined and the driver will inform about it:

exynos-tmu 10060000.tmu: Regulator node (vtmu) not found
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The Exynos Thermal Management Unit binding says that the vtmu-supply
is optional but is listed in the required properties section. Add an
optional properties section and move the regulator property there.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

When DeviveTree contains more trip-points than SoC can configure
(usually more than four) and polling mode is not enabled, then the
remaining trip-points will be silently ignored. No interrupts will be
generated for them.

This might be quite dangerous when one provides DTB with a
non-configurable critical trip-point, like (assuming four supported
thresholds in TMU):
 - alert @50 C (type: active),
 - alert @60 C (type: active),
 - alert @70 C (type: active),
 - alert @80 C (type: active),
 - critical @120 C (type: critical) <- no interrupts generated.

This is a mistake in DTB so print a message in such case.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Document the number of configurable temperature thresholds (for
trip-points in interrupt-driven mode).
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Commit 488c7455 ("thermal: exynos: Add the support for Exynos5433
TMU") added new compatible but forgot to update documentation.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The sign bit of temperature readback is bit 0, not bit 1.
Change to BIT(0) to fix it.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Matt Longnecker <mlongnecker@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed on many files with:

drivers/built-in.o: In function `kirkwood_thermal_probe':
kirkwood_thermal.c:(.text+0x390a25): undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `exynos_tmu_probe':
exynos_tmu.c:(.text+0x39246b): undefined reference to `devm_ioremap'

The users of devm_ioremap_resource() which are compile-testable should
depend on HAS_IOMEM.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

We don't need to initialize "ret".  We can move the IS_ERR() checks into
the if condition instead of doing an assignment first.  Also there is a
check for "ret" when we know it is zero so we can remove that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.

This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

This driver only has runtime but no build time dependencies, so it can be
built for testing purposes if the Kconfig COMPILE_TEST option is enabled.

This is useful to have more build coverage and make sure that drivers are
not affected by changes that could cause build regressions.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

As the TRM says, add the tsadc_q_sel to control the temperature-code
sequence since the rk3228/rk3399 need set this bit (1024 - tsadc_q)
as output.

Fixes: commit
b0d70338 "thermal: rockchip: Support the RK3399 SoCs in thermal driver"
7b02a5e7 "thermal: rockchip: Support the RK3228 SoCs in thermal driver"
Reported-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

This patch renames to be more adapter compatibles since more and more
SoCs are supported in thermal driver.
Reported-by: Huang,Tao <huangtao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

the calculation use a global table, not their own table.
so adapt the table to the correct one.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

As the Dan report the smatch check the thermal driver warning:
drivers/thermal/rockchip_thermal.c:551 rockchip_configure_from_dt()
warn: impossible condition '(thermal->tshut_temp > ((~0 >> 1))) =>
(s32min-s32max > s32max)'

Although The shut_temp read from DT is u32,the temperature is currently
represented as int not long in the thermal driver.
Let's change to make shut_temp instead of the thermal->tshut_temp for
the condition.

Fixes: commit 437df217
("thermal: rockchip: consistently use int for temperatures")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Pull perf fixes from Thomas Gleixner:
 "A rather largish series of 12 patches addressing a maze of race
  conditions in the perf core code from Peter Zijlstra"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Robustify task_function_call()
  perf: Fix scaling vs. perf_install_in_context()
  perf: Fix scaling vs. perf_event_enable()
  perf: Fix scaling vs. perf_event_enable_on_exec()
  perf: Fix ctx time tracking by introducing EVENT_TIME
  perf: Cure event->pending_disable race
  perf: Fix race between event install and jump_labels
  perf: Fix cloning
  perf: Only update context time when active
  perf: Allow perf_release() with !event->ctx
  perf: Do not double free
  perf: Close install vs. exit race

Pull x86 fixes from Thomas Gleixner:
 "This update contains:

   - Hopefully the last ASM CLAC fixups

   - A fix for the Quark family related to the IMR lock which makes
     kexec work again

   - A off-by-one fix in the MPX code.  Ironic, isn't it?

   - A fix for X86_PAE which addresses once more an unsigned long vs
     phys_addr_t hickup"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mpx: Fix off-by-one comparison with nr_registers
  x86/mm: Fix slow_virt_to_phys() for X86_PAE again
  x86/entry/compat: Add missing CLAC to entry_INT80_32
  x86/entry/32: Add an ASM_CLAC to entry_SYSENTER_32
  x86/platform/intel/quark: Change the kernel's IMR lock bit to false

Pull scheduler fixlet from Thomas Gleixner:
 "A trivial printk typo fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Fix trivial typo in printk() message

Pull irq fixes from Thomas Gleixner:
 "Four small fixes for irqchip drivers:

   - Add missing low level irq handler initialization on mxs, so
     interrupts can acutally be delivered

   - Add a missing barrier to the GIC driver

   - Two fixes for the GIC-V3-ITS driver, addressing a double EOI write
     and a cache flush beyond the actual region"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3: Add missing barrier to 32bit version of gic_read_iar()
  irqchip/mxs: Add missing set_handle_irq()
  irqchip/gicv3-its: Avoid cache flush beyond ITS_BASERn memory size
  irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1

Pull staging/android fix from Greg KH:
 "Here is one patch, for the android binder driver, to resolve a
  reported problem.  Turns out it has been around for a while (since
  3.15), so it is good to finally get it resolved.

  It has been in linux-next for a while with no reported issues"

* tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE

Pull USB fixes from Greg KH:
 "Here are a few USB fixes for 4.5-rc6

  They fix a reported bug for some USB 3 devices by reverting the recent
  patch, a MAINTAINERS change for some drivers, some new device ids, and
  of course, the usual bunch of USB gadget driver fixes.

  All have been in linux-next for a while with no reported issues"

* tag 'usb-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  MAINTAINERS: drop OMAP USB and MUSB maintainership
  usb: musb: fix DMA for host mode
  usb: phy: msm: Trigger USB state detection work in DRD mode
  usb: gadget: net2280: fix endpoint max packet for super speed connections
  usb: gadget: gadgetfs: unregister gadget only if it got successfully registered
  usb: gadget: remove driver from pending list on probe error
  Revert "usb: hub: do not clear BOS field during reset device"
  usb: chipidea: fix return value check in ci_hdrc_pci_probe()
  usb: chipidea: error on overflow for port_test_write
  USB: option: add "4G LTE usb-modem U901"
  USB: cp210x: add IDs for GE B650V3 and B850V3 boards
  USB: option: add support for SIM7100E
  usb: musb: Fix DMA desired mode for Mentor DMA engine
  usb: gadget: fsl_qe_udc: fix IS_ERR_VALUE usage
  usb: dwc2: USB_DWC2 should depend on HAS_DMA
  usb: dwc2: host: fix the data toggle error in full speed descriptor dma
  usb: dwc2: host: fix logical omissions in dwc2_process_non_isoc_desc
  usb: dwc3: Fix assignment of EP transfer resources
  usb: dwc2: Add extra delay when forcing dr_mode

Pull vfs fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  do_last(): ELOOP failure exit should be done after leaving RCU mode
  should_follow_link(): validate ->d_seq after having decided to follow
  namei: ->d_inode of a pinned dentry is stable only for positives
  do_last(): don't let a bogus return value from ->open() et.al. to confuse us
  fs: return -EOPNOTSUPP if clone is not supported
  hpfs: don't truncate the file when delete fails

Pull ARM SoC fixes from Olof Johansson:
 "We didn't have a batch last week, so this one is slightly larger.

  None of them are scary though, a handful of fixes for small DT pieces,
  replacing properties with newer conventions.

  Highlights:
   - N900 fix for setting system revision
   - onenand init fix to avoid filesystem corruption
   - Clock fix for audio on Beaglebone-x15
   - Fixes on shmobile to deal with CONFIG_DEBUG_RODATA (default y in 4.6)

  + misc smaller stuff"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Extend info, add wiki and ml for meson arch
  MAINTAINERS: alpine: add a new maintainer and update the entry
  ARM: at91/dt: fix typo in sama5d2 pinmux descriptions
  ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
  Revert "regulator: tps65217: remove tps65217.dtsi file"
  ARM: shmobile: Remove shmobile_boot_arg
  ARM: shmobile: Move shmobile_smp_{mpidr, fn, arg}[] from .text to .bss
  ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code
  ARM: shmobile: Move shmobile_scu_base from .text to .bss
  ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
  ARM: OMAP2+: Improve omap_device error for driver writers
  ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
  ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
  ARM: OMAP2+: Set system_rev from ATAGS for n900
  ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
  ARM: dts: kirkwood: use unique machine name for ds112
  ARM: dts: imx6: remove bogus interrupt-parent from CAAM node

... or we risk seeing a bogus value of d_is_symlink() there.

Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... otherwise d_is_symlink() above might have nothing to do with
the inode value we've got.

Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

both do_last() and walk_component() risk picking a NULL inode out
of dentry about to become positive, *then* checking its flags and
seeing that it's not negative anymore and using (already stale by
then) value they'd fetched earlier.  Usually ends up oopsing soon
after that...

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... into returning a positive to path_openat(), which would interpret that
as "symlink had been encountered" and proceed to corrupt memory, etc.
It can only happen due to a bug in some ->open() instance or in some LSM
hook, etc., so we report any such event *and* make sure it doesn't trick
us into further unpleasantness.

Cc: stable@vger.kernel.org # v3.6+, at least
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

-EBADF is a rather confusing error if an operations is not supported,
and nfsd gets rather upset about it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The delete opration can allocate additional space on the HPFS filesystem
due to btree split. The HPFS driver checks in advance if there is
available space, so that it won't corrupt the btree if we run out of space
during splitting.

If there is not enough available space, the HPFS driver attempted to
truncate the file, but this results in a deadlock since the commit
7dd29d8d ("HPFS: Introduce a global mutex
and lock it on every callback from VFS").

This patch removes the code that tries to truncate the file and -ENOSPC is
returned instead. If the user hits -ENOSPC on delete, he should try to
delete other files (that are stored in a leaf btree node), so that the
delete operation will make some space for deleting the file stored in
non-leaf btree node.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org	# 2.6.39+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Merge fixes from Andrew Morton:
 "10 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  dax: move writeback calls into the filesystems
  dax: give DAX clearing code correct bdev
  ext4: online defrag not supported with DAX
  ext2, ext4: only set S_DAX for regular inodes
  block: disable block device DAX by default
  ocfs2: unlock inode if deleting inode from orphan fails
  mm: ASLR: use get_random_long()
  drivers: char: random: add get_random_long()
  mm: numa: quickly fail allocations for NUMA balancing on full nodes
  mm: thp: fix SMP race condition between THP page fault and MADV_DONTNEED

Pull ext2/4 DAX fix from Ted Ts'o:
 "This fixes a file system corruption bug with DAX"

* tag 'tags/ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext2, ext4: fix issue with missing journal entry in ext4_dax_mkwrite()

Pull PCI fixes from Bjorn Helgaas:
 "Enumeration:
    Revert x86 pcibios_alloc_irq() to fix regression (Bjorn Helgaas)

  Marvell MVEBU host bridge driver:
    Restrict build to 32-bit ARM (Thierry Reding)"

* tag 'pci-v4.5-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: mvebu: Restrict build to 32-bit ARM
  Revert "PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()"
  Revert "PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed"
  Revert "x86/PCI: Don't alloc pcibios-irq when MSI is enabled"

As it is currently written ext4_dax_mkwrite() assumes that the call into
__dax_mkwrite() will not have to do a block allocation so it doesn't create
a journal entry.  For a read that creates a zero page to cover a hole
followed by a write that actually allocates storage this is incorrect.  The
ext4_dax_mkwrite() -> __dax_mkwrite() -> __dax_fault() path calls
get_blocks() to allocate storage.

Fix this by having the ->page_mkwrite fault handler call ext4_dax_fault()
as this function already has all the logic needed to allocate a journal
entry and call __dax_fault().

Also update the ext2 fault handlers in this same way to remove duplicate
code and keep the logic between ext2 and ext4 the same.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Pull clk fix from Stephen Boyd:
 "One small fix to keep OMAP platforms working across a suspend/resume
  cycle"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: ti: omap3+: dpll: use non-locking version of clk_get_rate

Previously calls to dax_writeback_mapping_range() for all DAX filesystems
(ext2, ext4 & xfs) were centralized in filemap_write_and_wait_range().

dax_writeback_mapping_range() needs a struct block_device, and it used
to get that from inode->i_sb->s_bdev.  This is correct for normal inodes
mounted on ext2, ext4 and XFS filesystems, but is incorrect for DAX raw
block devices and for XFS real-time files.

Instead, call dax_writeback_mapping_range() directly from the filesystem
->writepages function so that it can supply us with a valid block
device.  This also fixes DAX code to properly flush caches in response
to sync(2).
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dax_clear_blocks() needs a valid struct block_device and previously it
was using inode->i_sb->s_bdev in all cases.  This is correct for normal
inodes on mounted ext2, ext4 and XFS filesystems, but is incorrect for
DAX raw block devices and for XFS real-time devices.

Instead, rename dax_clear_blocks() to dax_clear_sectors(), and change
its arguments to take a bdev and a sector instead of an inode and a
block.  This better reflects what the function does, and it allows the
filesystem and raw block device code to pass in an appropriate struct
block_device.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Online defrag operations for ext4 are hard coded to use the page cache.
See ext4_ioctl() -> ext4_move_extents() -> move_extent_per_page()

When combined with DAX I/O, which circumvents the page cache, this can
result in data corruption.  This was observed with xfstests ext4/307 and
ext4/308.

Fix this by only allowing online defrag for non-DAX files.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When S_DAX is set on an inode we assume that if there are pages attached
to the mapping (mapping->nrpages != 0), those pages are clean zero pages
that were used to service reads from holes.  Any dirty data associated
with the inode should be in the form of DAX exceptional entries
(mapping->nrexceptional) that is written back via
dax_writeback_mapping_range().

With the current code, though, this isn't always true.  For example,
ext2 and ext4 directory inodes can have S_DAX set, but have their dirty
data stored as dirty page cache entries.  For these types of inodes,
having S_DAX set doesn't really make sense since their I/O doesn't
actually happen through the DAX code path.

Instead, only allow S_DAX to be set for regular inodes for ext2 and
ext4.  This allows us to have strict DAX vs non-DAX paths in the
writeback code.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>