- 25 Jan, 2008 40 commits
-
-
Michael Krufky authored
Store last tuned frequency & bandwidth after successful tune. Clean up tune functions -- remove pointer to tune function in state structure, instead call tune function based on priv->id. Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@infradead.org>
-
Michael Krufky authored
Always initialize registers during attach. Perform IR Calibration during init if needed. Perform RF Calibration during init if needed for C2, only. Signed-off-by:
-
Andrew Morton authored
video_register_device() returns -EFOO on errr, not -1. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9699 Reported-By: <devzero@web.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Mauro Carvalho Chehab authored
Acked-by:
Andrey J. Melnikov <temnota@kmv.ru> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Andrey J. Melnikoff (TEMHOTA) authored
This patch updates cardlist for Beholder TV tuners: old models (with GPIO ir) 401, 403, 405, 407, 409, 505, 507 and add support for 607, 609, M6 cards with new i2c-ir. Signed-off-by:
Igor Kuznetsov <igk72@yandex.ru> Signed-off-by:
-
Mauro Carvalho Chehab authored
Before this patch, only Vendor Class audio support were loaded. This means that older em28xx devices won't have digital audio support loaded. This patch changes the logic to auto load eighter snd-usb-audio, for devices with USB Audio Class or em28xx-alsa, for devices with USB Vendor Class. Signed-off-by: -
Mauro Carvalho Chehab authored
Only HVR950 has analog_gpio configured. It makes no sense to set gpio to 0 for other boards. Better to add a test, while this var is not set for all xc3028 devices. Signed-off-by: -
Michael Krufky authored
Create a device description and enable autodetection for Hauppauge WinTV PVR-USB2 Model 75xxx Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Michael Krufky authored
An earlier patch, "tda18271: fail table lookups if frequency is out of range" broke analog support on certain hardware. This patch fixes that problem, by allowing the RF_CAL byte to be set to the maximum value, in cases of the frequency being out of range. Signed-off-by:
-
Michael Krufky authored
Document debug level module options and tda18271_config attach-time parameters. Signed-off-by:
-
Michael Krufky authored
Store IF Frequency in a u16 instead of a u32. Multiply by 1000 before use. Signed-off-by:
-
Michael Krufky authored
Allow drivers to pass device-specific configuration parameters during attach. If these parameters are omitted, default values will be used. Signed-off-by:
-
Michael Krufky authored
Move some common code to a new file to make this easier to look at. Signed-off-by:
-
Michael Krufky authored
Tested successfully with QAM256 digital cable. Analog television is limping, needs more work. Signed-off-by:
-
Michael Krufky authored
version 0.1 Signed-off-by:
-
Michael Krufky authored
make set_analog_params function look consistent with set_params function Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Try to load non-MTS firmware instead. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Older em28xx devices does implement standard Audio Class. However, on newer devices, this were replaced by a Vendor Class. This patch autodetects that an em28xx lacks Audio Class and auto-loads em28xx-alsa, for the devices that implements only a Vendor Class. For devices with Audio Class, snd-usb-audio module will provide an ALSA interface. This patch uses the request_module_async function as defined on cx88-mpeg.c, originally wrote by Markus Rechberger. Signed-off-by: -
Mauro Carvalho Chehab authored
Also fixes the remaining CodingStyle issues that Lindent didn't fix. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Markus Rechberger authored
em28xx-audio module exports em28xx Vendor Class audio as an -alsa driver. This module were written based on usbaudio driver by Markus Rechberger. Recently, he acked to allow us to merge it on kernel: http://lists-archives.org/video4linux/20408-supporting-prolink-pixelview-405-dvd-maker.html Thanks to Markus Rechberger <mrechberger@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Thanks to Markus Rechberger <mrechberger@gmail.com> for retriving those commands. Also, MTS firmware is required for audio to work on HVR950. Signed-off-by: -
Mauro Carvalho Chehab authored
It is possible to select audio inputs via em28xx or via ac97 functions. This patch allows configuring a board to use either one way. It also do some cleanups at audio setup configurations. Signed-off-by: -
Mauro Carvalho Chehab authored
Due to tuner-xc2028.h, some extra directories should be added at .h search. Signed-off-by: -
Mauro Carvalho Chehab authored
This tool allows the extraction of xc3028 v2.7 firmware from HVR 12x0 file. Signed-off-by: -
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Steven Toth authored
Basic cleanup. Signed-off-by:
Steven Toth <stoth@hauppauge.com> Signed-off-by:
-
Michael Krufky authored
Break out the following new functions from tda18271_tune: tda18271_calc_bp_filter tda18271_calc_km tda18271_calc_rf_band tda18271_calc_gain_taper tda18271_calc_ir_measure tda18271_calc_rf_cal Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
