commit 342406e4 upstream.

For a while, we've had the problem of i2c bus access not grabbing
a runtime PM ref when it's being used in userspace by i2c-dev, resulting
in nouveau spamming the kernel log with errors if anything attempts to
access the i2c bus while the GPU is in runtime suspend. An example:

[  130.078386] nouveau 0000:01:00.0: i2c: aux 000d: begin idle timeout ffffffff

Since the GPU is in runtime suspend, the MMIO region that the i2c bus is
on isn't accessible. On x86, the standard behavior for accessing an
unavailable MMIO region is to just return ~0.

Except, that turned out to be a lie. While computers with a clean
concious will return ~0 in this scenario, some machines will actually
completely hang a CPU on certian bad MMIO accesses. This was witnessed
with someone's Lenovo ThinkPad P50, where sensors-detect attempting to
access the i2c bus while the GPU was suspended would result in a CPU
hang:

  CPU: 5 PID: 12438 Comm: sensors-detect Not tainted 5.0.0-0.rc4.git3.1.fc30.x86_64 #1
  Hardware name: LENOVO 20EQS64N17/20EQS64N17, BIOS N1EET74W (1.47 ) 11/21/2017
  RIP: 0010:ioread32+0x2b/0x30
  Code: 81 ff ff ff 03 00 77 20 48 81 ff 00 00 01 00 76 05 0f b7 d7 ed c3
  48 c7 c6 e1 0c 36 96 e8 2d ff ff ff b8 ff ff ff ff c3 8b 07 <c3> 0f 1f
  40 00 49 89 f0 48 81 fe ff ff 03 00 76 04 40 88 3e c3 48
  RSP: 0018:ffffaac3c5007b48 EFLAGS: 00000292 ORIG_RAX: ffffffffffffff13
  RAX: 0000000001111000 RBX: 0000000001111000 RCX: 0000043017a97186
  RDX: 0000000000000aaa RSI: 0000000000000005 RDI: ffffaac3c400e4e4
  RBP: ffff9e6443902c00 R08: ffffaac3c400e4e4 R09: ffffaac3c5007be7
  R10: 0000000000000004 R11: 0000000000000001 R12: ffff9e6445dd0000
  R13: 000000000000e4e4 R14: 00000000000003c4 R15: 0000000000000000
  FS:  00007f253155a740(0000) GS:ffff9e644f600000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00005630d1500358 CR3: 0000000417c44006 CR4: 00000000003606e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   g94_i2c_aux_xfer+0x326/0x850 [nouveau]
   nvkm_i2c_aux_i2c_xfer+0x9e/0x140 [nouveau]
   __i2c_transfer+0x14b/0x620
   i2c_smbus_xfer_emulated+0x159/0x680
   ? _raw_spin_unlock_irqrestore+0x1/0x60
   ? rt_mutex_slowlock.constprop.0+0x13d/0x1e0
   ? __lock_is_held+0x59/0xa0
   __i2c_smbus_xfer+0x138/0x5a0
   i2c_smbus_xfer+0x4f/0x80
   i2cdev_ioctl_smbus+0x162/0x2d0 [i2c_dev]
   i2cdev_ioctl+0x1db/0x2c0 [i2c_dev]
   do_vfs_ioctl+0x408/0x750
   ksys_ioctl+0x5e/0x90
   __x64_sys_ioctl+0x16/0x20
   do_syscall_64+0x60/0x1e0
   entry_SYSCALL_64_after_hwframe+0x49/0xbe
  RIP: 0033:0x7f25317f546b
  Code: 0f 1e fa 48 8b 05 1d da 0c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff
  ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01
  f0 ff ff 73 01 c3 48 8b 0d ed d9 0c 00 f7 d8 64 89 01 48
  RSP: 002b:00007ffc88caab68 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
  RAX: ffffffffffffffda RBX: 00005630d0fe7260 RCX: 00007f25317f546b
  RDX: 00005630d1598e80 RSI: 0000000000000720 RDI: 0000000000000003
  RBP: 00005630d155b968 R08: 0000000000000001 R09: 00005630d15a1da0
  R10: 0000000000000070 R11: 0000000000000246 R12: 00005630d1598e80
  R13: 00005630d12f3d28 R14: 0000000000000720 R15: 00005630d12f3ce0
  watchdog: BUG: soft lockup - CPU#5 stuck for 23s! [sensors-detect:12438]

Yikes! While I wanted to try to make it so that accessing an i2c bus on
nouveau would wake up the GPU as needed, airlied pointed out that pretty
much any usecase for userspace accessing an i2c bus on a GPU (mainly for
the DDC brightness control that some displays have) is going to only be
useful while there's at least one display enabled on the GPU anyway, and
the GPU never sleeps while there's displays running.

Since teaching the i2c bus to wake up the GPU on userspace accesses is a
good deal more difficult than it might seem, mostly due to the fact that
we have to use the i2c bus during runtime resume of the GPU, we instead
opt for the easiest solution: don't let userspace access i2c busses on
the GPU at all while it's in runtime suspend.

Changes since v1:
* Also disable i2c busses that run over DP AUX
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a86cb413 upstream.

KVM_CAP_MAX_VCPU_ID is currently always reporting KVM_MAX_VCPU_ID on all
architectures. However, on s390x, the amount of usable CPUs is determined
during runtime - it is depending on the features of the machine the code
is running on. Since we are using the vcpu_id as an index into the SCA
structures that are defined by the hardware (see e.g. the sca_add_vcpu()
function), it is not only the amount of CPUs that is limited by the hard-
ware, but also the range of IDs that we can use.
Thus KVM_CAP_MAX_VCPU_ID must be determined during runtime on s390x, too.
So the handling of KVM_CAP_MAX_VCPU_ID has to be moved from the common
code into the architecture specific code, and on s390x we have to return
the same value here as for KVM_CAP_MAX_VCPUS.
This problem has been discovered with the kvm_create_max_vcpus selftest.
With this change applied, the selftest now passes on s390x, too.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190523164309.13345-9-thuth@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9cb40eb1 upstream.

We met another Acer Aspire laptop which has the problem on the
headset-mic, the Pin 0x19 is not set the corret configuration for a
mic and the pin presence can't be detected too after plugging a
headset. Kailang suggested that we should set the coeff to enable the
mic and apply the ALC269_FIXUP_LIFEBOOK_EXTMIC. After doing that,
both headset-mic presence and headset-mic work well.

The existing ALC255_FIXUP_ACER_MIC_NO_PRESENCE set the headset-mic
jack to be a phantom jack. Now since the jack can support presence
unsol event, let us imporve it to set the jack to be a normal jack.

https://bugs.launchpad.net/bugs/1821269
Fixes: 5824ce8d ("ALSA: hda/realtek - Add support for Acer Aspire E5-475 headset mic")
Cc: Chris Chiu <chiu@endlessm.com>
CC: Daniel Drake <drake@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 317d9313 upstream.

I measured power consumption between power_save_node=1 and power_save_node=0.
It's almost the same.
Codec will enter to runtime suspend and suspend.
That pin also will enter to D3. Don't need to enter to D3 by single pin.
So, Disable power_save_node as default. It will avoid more issues.
Windows Driver also has not this option at runtime PM.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0b074ab7 upstream.

The current code performs the cancel of a delayed work at the late
stage of disconnection procedure, which may lead to the access to the
already cleared state.

This patch assures to call cancel_delayed_work_sync() at the beginning
of the disconnection procedure for avoiding that race.  The delayed
work object is now assigned in the common line6 object instead of its
derivative, so that we can call cancel_delayed_work_sync().

Along with the change, the startup function is called via the new
callback instead.  This will make it easier to port other LINE6
drivers to use the delayed work for startup in later patches.

Reported-by: syzbot+5255458d5e0a2b10bbb9@syzkaller.appspotmail.com
Fixes: 7f84ff68 ("ALSA: line6: toneport: Fix broken usage of timer for delayed execution")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8b909e35 upstream.

Commit b6664ba4 ("s390, kexec_file: drop arch_kexec_mem_walk()")
changed kexec_add_buffer() to skip searching for a memory location if
kexec_buf.mem is already set, and use the address that is there.

In powerpc code we reuse a kexec_buf variable for loading both the
kernel and the initramfs by resetting some of the fields between those
uses, but not mem. This causes kexec_add_buffer() to try to load the
kernel at the same address where initramfs will be loaded, which is
naturally rejected:

  # kexec -s -l --initrd initramfs vmlinuz
  kexec_file_load failed: Invalid argument

Setting the mem field before every call to kexec_add_buffer() fixes
this regression.

Fixes: b6664ba4 ("s390, kexec_file: drop arch_kexec_mem_walk()")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Reviewed-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3202e35e upstream.

Consider a scenario where user creates two events:

  1st event:
    attr.sample_type |= PERF_SAMPLE_BRANCH_STACK;
    attr.branch_sample_type = PERF_SAMPLE_BRANCH_ANY;
    fd = perf_event_open(attr, 0, 1, -1, 0);

  This sets cpuhw->bhrb_filter to 0 and returns valid fd.

  2nd event:
    attr.sample_type |= PERF_SAMPLE_BRANCH_STACK;
    attr.branch_sample_type = PERF_SAMPLE_BRANCH_CALL;
    fd = perf_event_open(attr, 0, 1, -1, 0);

  It overrides cpuhw->bhrb_filter to -1 and returns with error.

Now if power_pmu_enable() gets called by any path other than
power_pmu_add(), ppmu->config_bhrb(-1) will set MMCRA to -1.

Fixes: 3925f46b ("powerpc/perf: Enable branch stack sampling framework")
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d724c9e5 upstream.

The sprgs are a set of 4 general purpose sprs provided for software use.
SPRG3 is special in that it can also be read from userspace. Thus it is
used on linux to store the cpu and numa id of the process to speed up
syscall access to this information.

This register is overwritten with the guest value on kvm guest entry,
and so needs to be restored on exit again. Thus restore the value on
the guest exit path in kvmhv_p9_guest_entry().

Cc: stable@vger.kernel.org # v4.20+
Fixes: 95a6432c ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests")
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1b28d553 upstream.

Commit 3309bec8 ("KVM: PPC: Book3S HV: Fix lockdep warning when
entering the guest") moved calls to trace_hardirqs_{on,off} in the
entry path used for HPT guests.  Similar code exists in the new
streamlined entry path used for radix guests on POWER9.  This makes
the same change there, so as to avoid lockdep warnings such as this:

[  228.686461] DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled)
[  228.686480] WARNING: CPU: 116 PID: 3803 at ../kernel/locking/lockdep.c:4219 check_flags.part.23+0x21c/0x270
[  228.686544] Modules linked in: vhost_net vhost xt_CHECKSUM iptable_mangle xt_MASQUERADE iptable_nat nf_nat
+xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ipt_REJECT nf_reject_ipv4 tun bridge stp llc ebtable_filter
+ebtables ip6table_filter ip6_tables iptable_filter fuse kvm_hv kvm at24 ipmi_powernv regmap_i2c ipmi_devintf
+uio_pdrv_genirq ofpart ipmi_msghandler uio powernv_flash mtd ibmpowernv opal_prd ip_tables ext4 mbcache jbd2 btrfs
+zstd_decompress zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx libcrc32c xor
+raid6_pq raid1 raid0 ses sd_mod enclosure scsi_transport_sas ast i2c_opal i2c_algo_bit drm_kms_helper syscopyarea
+sysfillrect sysimgblt fb_sys_fops ttm drm i40e e1000e cxl aacraid tg3 drm_panel_orientation_quirks i2c_core
[  228.686859] CPU: 116 PID: 3803 Comm: qemu-system-ppc Kdump: loaded Not tainted 5.2.0-rc1-xive+ #42
[  228.686911] NIP:  c0000000001b394c LR: c0000000001b3948 CTR: c000000000bfad20
[  228.686963] REGS: c000200cdb50f570 TRAP: 0700   Not tainted  (5.2.0-rc1-xive+)
[  228.687001] MSR:  9000000002823033 <SF,HV,VEC,VSX,FP,ME,IR,DR,RI,LE>  CR: 48222222  XER: 20040000
[  228.687060] CFAR: c000000000116db0 IRQMASK: 1
[  228.687060] GPR00: c0000000001b3948 c000200cdb50f800 c0000000015e7600 000000000000002e
[  228.687060] GPR04: 0000000000000001 c0000000001c71a0 000000006e655f73 72727563284e4f5f
[  228.687060] GPR08: 0000200e60680000 0000000000000000 c000200cdb486180 0000000000000000
[  228.687060] GPR12: 0000000000002000 c000200fff61a680 0000000000000000 00007fffb75c0000
[  228.687060] GPR16: 0000000000000000 0000000000000000 c0000000017d6900 c000000001124900
[  228.687060] GPR20: 0000000000000074 c008000006916f68 0000000000000074 0000000000000074
[  228.687060] GPR24: ffffffffffffffff ffffffffffffffff 0000000000000003 c000200d4b600000
[  228.687060] GPR28: c000000001627e58 c000000001489908 c000000001627e58 c000000002304de0
[  228.687377] NIP [c0000000001b394c] check_flags.part.23+0x21c/0x270
[  228.687415] LR [c0000000001b3948] check_flags.part.23+0x218/0x270
[  228.687466] Call Trace:
[  228.687488] [c000200cdb50f800] [c0000000001b3948] check_flags.part.23+0x218/0x270 (unreliable)
[  228.687542] [c000200cdb50f870] [c0000000001b6548] lock_is_held_type+0x188/0x1c0
[  228.687595] [c000200cdb50f8d0] [c0000000001d939c] rcu_read_lock_sched_held+0xdc/0x100
[  228.687646] [c000200cdb50f900] [c0000000001dd704] rcu_note_context_switch+0x304/0x340
[  228.687701] [c000200cdb50f940] [c0080000068fcc58] kvmhv_run_single_vcpu+0xdb0/0x1120 [kvm_hv]
[  228.687756] [c000200cdb50fa20] [c0080000068fd5b0] kvmppc_vcpu_run_hv+0x5e8/0xe40 [kvm_hv]
[  228.687816] [c000200cdb50faf0] [c0080000071797dc] kvmppc_vcpu_run+0x34/0x48 [kvm]
[  228.687863] [c000200cdb50fb10] [c0080000071755dc] kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm]
[  228.687916] [c000200cdb50fba0] [c008000007165ccc] kvm_vcpu_ioctl+0x424/0x838 [kvm]
[  228.687957] [c000200cdb50fd10] [c000000000433a24] do_vfs_ioctl+0xd4/0xcd0
[  228.687995] [c000200cdb50fdb0] [c000000000434724] ksys_ioctl+0x104/0x120
[  228.688033] [c000200cdb50fe00] [c000000000434768] sys_ioctl+0x28/0x80
[  228.688072] [c000200cdb50fe20] [c00000000000b888] system_call+0x5c/0x70
[  228.688109] Instruction dump:
[  228.688142] 4bf6342d 60000000 0fe00000 e8010080 7c0803a6 4bfffe60 3c82ff87 3c62ff87
[  228.688196] 388472d0 3863d738 4bf63405 60000000 <0fe00000> 4bffff4c 3c82ff87 3c62ff87
[  228.688251] irq event stamp: 205
[  228.688287] hardirqs last  enabled at (205): [<c0080000068fc1b4>] kvmhv_run_single_vcpu+0x30c/0x1120 [kvm_hv]
[  228.688344] hardirqs last disabled at (204): [<c0080000068fbff0>] kvmhv_run_single_vcpu+0x148/0x1120 [kvm_hv]
[  228.688412] softirqs last  enabled at (180): [<c000000000c0b2ac>] __do_softirq+0x4ac/0x5d4
[  228.688464] softirqs last disabled at (169): [<c000000000122aa8>] irq_exit+0x1f8/0x210
[  228.688513] ---[ end trace eb16f6260022a812 ]---
[  228.688548] possible reason: unannotated irqs-off.
[  228.688571] irq event stamp: 205
[  228.688607] hardirqs last  enabled at (205): [<c0080000068fc1b4>] kvmhv_run_single_vcpu+0x30c/0x1120 [kvm_hv]
[  228.688664] hardirqs last disabled at (204): [<c0080000068fbff0>] kvmhv_run_single_vcpu+0x148/0x1120 [kvm_hv]
[  228.688719] softirqs last  enabled at (180): [<c000000000c0b2ac>] __do_softirq+0x4ac/0x5d4
[  228.688758] softirqs last disabled at (169): [<c000000000122aa8>] irq_exit+0x1f8/0x210

Cc: stable@vger.kernel.org # v4.20+
Fixes: 95a6432c ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ef974020 upstream.

The passthrough interrupts are defined at the host level and their IRQ
data should not be cleared unless specifically deconfigured (shutdown)
by the host. They differ from the IPI interrupts which are allocated
by the XIVE KVM device and reserved to the guest usage only.

This fixes a host crash when destroying a VM in which a PCI adapter
was passed-through. In this case, the interrupt is cleared and freed
by the KVM device and then shutdown by vfio at the host level.

[ 1007.360265] BUG: Kernel NULL pointer dereference at 0x00000d00
[ 1007.360285] Faulting instruction address: 0xc00000000009da34
[ 1007.360296] Oops: Kernel access of bad area, sig: 7 [#1]
[ 1007.360303] LE PAGE_SIZE=64K MMU=Radix MMU=Hash SMP NR_CPUS=2048 NUMA PowerNV
[ 1007.360314] Modules linked in: vhost_net vhost iptable_mangle ipt_MASQUERADE iptable_nat nf_nat xt_conntrack nf_conntrack nf_defrag_ipv4 ipt_REJECT nf_reject_ipv4 tun bridge stp llc kvm_hv kvm xt_tcpudp iptable_filter squashfs fuse binfmt_misc vmx_crypto ib_iser rdma_cm iw_cm ib_cm libiscsi scsi_transport_iscsi nfsd ip_tables x_tables autofs4 btrfs zstd_decompress zstd_compress lzo_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq multipath mlx5_ib ib_uverbs ib_core crc32c_vpmsum mlx5_core
[ 1007.360425] CPU: 9 PID: 15576 Comm: CPU 18/KVM Kdump: loaded Not tainted 5.1.0-gad7e7d0ef #4
[ 1007.360454] NIP:  c00000000009da34 LR: c00000000009e50c CTR: c00000000009e5d0
[ 1007.360482] REGS: c000007f24ccf330 TRAP: 0300   Not tainted  (5.1.0-gad7e7d0ef)
[ 1007.360500] MSR:  900000000280b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE>  CR: 24002484  XER: 00000000
[ 1007.360532] CFAR: c00000000009da10 DAR: 0000000000000d00 DSISR: 00080000 IRQMASK: 1
[ 1007.360532] GPR00: c00000000009e62c c000007f24ccf5c0 c000000001510600 c000007fe7f947c0
[ 1007.360532] GPR04: 0000000000000d00 0000000000000000 0000000000000000 c000005eff02d200
[ 1007.360532] GPR08: 0000000000400000 0000000000000000 0000000000000000 fffffffffffffffd
[ 1007.360532] GPR12: c00000000009e5d0 c000007fffff7b00 0000000000000031 000000012c345718
[ 1007.360532] GPR16: 0000000000000000 0000000000000008 0000000000418004 0000000000040100
[ 1007.360532] GPR20: 0000000000000000 0000000008430000 00000000003c0000 0000000000000027
[ 1007.360532] GPR24: 00000000000000ff 0000000000000000 00000000000000ff c000007faa90d98c
[ 1007.360532] GPR28: c000007faa90da40 00000000000fe040 ffffffffffffffff c000007fe7f947c0
[ 1007.360689] NIP [c00000000009da34] xive_esb_read+0x34/0x120
[ 1007.360706] LR [c00000000009e50c] xive_do_source_set_mask.part.0+0x2c/0x50
[ 1007.360732] Call Trace:
[ 1007.360738] [c000007f24ccf5c0] [c000000000a6383c] snooze_loop+0x15c/0x270 (unreliable)
[ 1007.360775] [c000007f24ccf5f0] [c00000000009e62c] xive_irq_shutdown+0x5c/0xe0
[ 1007.360795] [c000007f24ccf630] [c00000000019e4a0] irq_shutdown+0x60/0xe0
[ 1007.360813] [c000007f24ccf660] [c000000000198c44] __free_irq+0x3a4/0x420
[ 1007.360831] [c000007f24ccf700] [c000000000198dc8] free_irq+0x78/0xe0
[ 1007.360849] [c000007f24ccf730] [c00000000096c5a8] vfio_msi_set_vector_signal+0xa8/0x350
[ 1007.360878] [c000007f24ccf7f0] [c00000000096c938] vfio_msi_set_block+0xe8/0x1e0
[ 1007.360899] [c000007f24ccf850] [c00000000096cae0] vfio_msi_disable+0xb0/0x110
[ 1007.360912] [c000007f24ccf8a0] [c00000000096cd04] vfio_pci_set_msi_trigger+0x1c4/0x3d0
[ 1007.360922] [c000007f24ccf910] [c00000000096d910] vfio_pci_set_irqs_ioctl+0xa0/0x170
[ 1007.360941] [c000007f24ccf930] [c00000000096b400] vfio_pci_disable+0x80/0x5e0
[ 1007.360963] [c000007f24ccfa10] [c00000000096b9bc] vfio_pci_release+0x5c/0x90
[ 1007.360991] [c000007f24ccfa40] [c000000000963a9c] vfio_device_fops_release+0x3c/0x70
[ 1007.361012] [c000007f24ccfa70] [c0000000003b5668] __fput+0xc8/0x2b0
[ 1007.361040] [c000007f24ccfac0] [c0000000001409b0] task_work_run+0x140/0x1b0
[ 1007.361059] [c000007f24ccfb20] [c000000000118f8c] do_exit+0x3ac/0xd00
[ 1007.361076] [c000007f24ccfc00] [c0000000001199b0] do_group_exit+0x60/0x100
[ 1007.361094] [c000007f24ccfc40] [c00000000012b514] get_signal+0x1a4/0x8f0
[ 1007.361112] [c000007f24ccfd30] [c000000000021cc8] do_notify_resume+0x1a8/0x430
[ 1007.361141] [c000007f24ccfe20] [c00000000000e444] ret_from_except_lite+0x70/0x74
[ 1007.361159] Instruction dump:
[ 1007.361175] 38422c00 e9230000 712a0004 41820010 548a2036 7d442378 78840020 71290020
[ 1007.361194] 4082004c e9230010 7c892214 7c0004ac <e9240000> 0c090000 4c00012c 792a0022

Cc: stable@vger.kernel.org # v4.12+
Fixes: 5af50993 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1c2c7029 upstream.

This patch fixes a complain about possible sleep during
spinlock aquired
"BUG: sleeping function called from invalid context at
include/crypto/algapi.h:426"
for the ctr(aes) and ctr(des) s390 specific ciphers.

Instead of using a spinlock this patch introduces a mutex
which is save to be held in sleeping context. Please note
a deadlock is not possible as mutex_trylock() is used.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bef9f0ba upstream.

The current kernel uses improved crypto selftests. These
tests showed that the current implementation of gcm-aes-s390
is not able to deal with chunks of output buffers which are
not a multiple of 16 bytes. This patch introduces a rework
of the gcm aes s390 scatter walk handling which now is able
to handle any input and output scatter list chunk sizes
correctly.

Code has been verified by the crypto selftests, the tcrypt
kernel module and additional tests ran via the af_alg interface.

Cc: <stable@vger.kernel.org>
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Patrick Steuer <steuer@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e6d12298 upstream.

When using the hrtimer iio trigger timestamp isn't updated.
If we use iio_get_time_ns it is updated correctly.

Fixes: 2a864877 ("iio: adc: ti-ads8688: add trigger and buffer support")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4e63ed6b upstream.

Checking if regulator is valid before reading
NPCM ADC regulator voltage to avoid system crash
in a case the regulator is not valid.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0db8aa49 upstream.

When initializing the priv->data array starting from index 1, there is one
less element to consider than when initializing the full array.

Fixes: e717f8c6 ("iio: adc: Add the TI ads124s08 ADC code")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 60f22086 upstream.

The ds4424_get_value function takes channel number as it's 3rd
argument and translates it internally into I2C address using
DS4424_DAC_ADDR macro. The caller ds4424_verify_chip was passing an
already translated I2C address as its last argument.
Signed-off-by: Ruslan Babayev <ruslan@babayev.com>
Cc: xe-linux-external@cisco.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 30d40577 upstream.

[BUG]
When a fs has orphan reloc tree along with unfinished balance:
  ...
        item 16 key (TREE_RELOC ROOT_ITEM FS_TREE) itemoff 12090 itemsize 439
                generation 12 root_dirid 256 bytenr 300400640 level 1 refs 0 <<<
                lastsnap 8 byte_limit 0 bytes_used 1359872 flags 0x0(none)
                uuid 7c48d938-33a3-4aae-ab19-6e5c9d406e46
        item 17 key (BALANCE TEMPORARY_ITEM 0) itemoff 11642 itemsize 448
                temporary item objectid BALANCE offset 0
                balance status flags 14

Then at mount time, we can hit the following kernel BUG_ON():
  BTRFS info (device dm-3): relocating block group 298844160 flags metadata|dup
  ------------[ cut here ]------------
  kernel BUG at fs/btrfs/relocation.c:1413!
  invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
  CPU: 1 PID: 897 Comm: btrfs-balance Tainted: G           O      5.2.0-rc1-custom #15
  RIP: 0010:create_reloc_root+0x1eb/0x200 [btrfs]
  Call Trace:
   btrfs_init_reloc_root+0x96/0xb0 [btrfs]
   record_root_in_trans+0xb2/0xe0 [btrfs]
   btrfs_record_root_in_trans+0x55/0x70 [btrfs]
   select_reloc_root+0x7e/0x230 [btrfs]
   do_relocation+0xc4/0x620 [btrfs]
   relocate_tree_blocks+0x592/0x6a0 [btrfs]
   relocate_block_group+0x47b/0x5d0 [btrfs]
   btrfs_relocate_block_group+0x183/0x2f0 [btrfs]
   btrfs_relocate_chunk+0x4e/0xe0 [btrfs]
   btrfs_balance+0x864/0xfa0 [btrfs]
   balance_kthread+0x3b/0x50 [btrfs]
   kthread+0x123/0x140
   ret_from_fork+0x27/0x50

[CAUSE]
In btrfs, reloc trees are used to record swapped tree blocks during
balance.
Reloc tree either get merged (replace old tree blocks of its parent
subvolume) in next transaction if its ref is 1 (fresh).
Or is already merged and will be cleaned up if its ref is 0 (orphan).

After commit d2311e69 ("btrfs: relocation: Delay reloc tree deletion
after merge_reloc_roots"), reloc tree cleanup is delayed until one block
group is balanced.

Since fresh reloc roots are recorded during merge, as long as there
is no power loss, those orphan reloc roots converted from fresh ones are
handled without problem.

However when power loss happens, orphan reloc roots can be recorded
on-disk, thus at next mount time, we will have orphan reloc roots from
on-disk data directly, and ignored by clean_dirty_subvols() routine.

Then when background balance starts to balance another block group, and
needs to create new reloc root for the same root, btrfs_insert_item()
returns -EEXIST, and trigger that BUG_ON().

[FIX]
For orphan reloc roots, also queue them to rc->dirty_subvol_roots, so
all reloc roots no matter orphan or not, can be cleaned up properly and
avoid above BUG_ON().

And to cooperate with above change, clean_dirty_subvols() will check if
the queued root is a reloc root or a subvol root.
For a subvol root, do the old work, and for a orphan reloc root, clean it
up.

Fixes: d2311e69 ("btrfs: relocation: Delay reloc tree deletion after merge_reloc_roots")
CC: stable@vger.kernel.org # 5.1
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6b1f72e5 upstream.

When using the no-holes feature, if we have a file with prealloc extents
with a start offset beyond the file's eof, doing an incremental send can
cause corruption of the file due to incorrect hole detection. Such case
requires that the prealloc extent(s) exist in both the parent and send
snapshots, and that a hole is punched into the file that covers all its
extents that do not cross the eof boundary.

Example reproducer:

  $ mkfs.btrfs -f -O no-holes /dev/sdb
  $ mount /dev/sdb /mnt/sdb

  $ xfs_io -f -c "pwrite -S 0xab 0 500K" /mnt/sdb/foobar
  $ xfs_io -c "falloc -k 1200K 800K" /mnt/sdb/foobar

  $ btrfs subvolume snapshot -r /mnt/sdb /mnt/sdb/base

  $ btrfs send -f /tmp/base.snap /mnt/sdb/base

  $ xfs_io -c "fpunch 0 500K" /mnt/sdb/foobar

  $ btrfs subvolume snapshot -r /mnt/sdb /mnt/sdb/incr

  $ btrfs send -p /mnt/sdb/base -f /tmp/incr.snap /mnt/sdb/incr

  $ md5sum /mnt/sdb/incr/foobar
  816df6f64deba63b029ca19d880ee10a   /mnt/sdb/incr/foobar

  $ mkfs.btrfs -f /dev/sdc
  $ mount /dev/sdc /mnt/sdc

  $ btrfs receive -f /tmp/base.snap /mnt/sdc
  $ btrfs receive -f /tmp/incr.snap /mnt/sdc

  $ md5sum /mnt/sdc/incr/foobar
  cf2ef71f4a9e90c2f6013ba3b2257ed2   /mnt/sdc/incr/foobar

    --> Different checksum, because the prealloc extent beyond the
        file's eof confused the hole detection code and it assumed
        a hole starting at offset 0 and ending at the offset of the
        prealloc extent (1200Kb) instead of ending at the offset
        500Kb (the file's size).

Fix this by ensuring we never cross the file's size when issuing the
write operations for a hole.

Fixes: 16e7549f ("Btrfs: incompatible format change to remove hole extents")
CC: stable@vger.kernel.org # 3.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 57949d03 upstream.

[BUG]
When mounting a fs with reloc tree and has qgroup enabled, it can cause
NULL pointer dereference at mount time:

  BUG: kernel NULL pointer dereference, address: 00000000000000a8
  #PF: supervisor read access in kernel mode
  #PF: error_code(0x0000) - not-present page
  PGD 0 P4D 0
  Oops: 0000 [#1] PREEMPT SMP NOPTI
  RIP: 0010:btrfs_qgroup_add_swapped_blocks+0x186/0x300 [btrfs]
  Call Trace:
   replace_path.isra.23+0x685/0x900 [btrfs]
   merge_reloc_root+0x26e/0x5f0 [btrfs]
   merge_reloc_roots+0x10a/0x1a0 [btrfs]
   btrfs_recover_relocation+0x3cd/0x420 [btrfs]
   open_ctree+0x1bc8/0x1ed0 [btrfs]
   btrfs_mount_root+0x544/0x680 [btrfs]
   legacy_get_tree+0x34/0x60
   vfs_get_tree+0x2d/0xf0
   fc_mount+0x12/0x40
   vfs_kern_mount.part.12+0x61/0xa0
   vfs_kern_mount+0x13/0x20
   btrfs_mount+0x16f/0x860 [btrfs]
   legacy_get_tree+0x34/0x60
   vfs_get_tree+0x2d/0xf0
   do_mount+0x81f/0xac0
   ksys_mount+0xbf/0xe0
   __x64_sys_mount+0x25/0x30
   do_syscall_64+0x65/0x240
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

[CAUSE]
In btrfs_recover_relocation(), we don't have enough info to determine
which block group we're relocating, but only to merge existing reloc
trees.

Thus in btrfs_recover_relocation(), rc->block_group is NULL.
btrfs_qgroup_add_swapped_blocks() hasn't taken this into consideration,
and causes a NULL pointer dereference.

The bug is introduced by commit 3d0174f7 ("btrfs: qgroup: Only trace
data extents in leaves if we're relocating data block group"), and
later qgroup refactoring still keeps this optimization.

[FIX]
Thankfully in the context of btrfs_recover_relocation(), there is no
other progress can modify tree blocks, thus those swapped tree blocks
pair will never affect qgroup numbers, no matter whatever we set for
block->trace_leaf.

So we only need to check if @bg is NULL before accessing @bg->flags.
Reported-by: Juan Erbes <jerbes@gmail.com>
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1134806
Fixes: 3d0174f7 ("btrfs: qgroup: Only trace data extents in leaves if we're relocating data block group")
CC: stable@vger.kernel.org # 4.20+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fee13fe9 upstream.

The btrfs zstd workspace manager uses a background timer to reclaim not
recently used workspaces. I used spin_lock() from this context which
should have been caught with lockdep, but was not. This deadlock was
reported in bugzilla. The fix is to switch the zstd wsm lock to use
spin_lock_bh() from the softirq context.

This happened quite relibably on ppc64, unlike on other architectures.

  [  313.402874] ================================
  [  313.402875] WARNING: inconsistent lock state
  [  313.402879] 5.1.0-rc7 #1 Not tainted
  [  313.402880] --------------------------------
  [  313.402882] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
  [  313.402885] swapper/5/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
  [  313.402888] 0000000080d1120c (&(&wsm.lock)->rlock){+.?.}, at: .zstd_reclaim_timer_fn+0x40/0x230
  [  313.402895] {SOFTIRQ-ON-W} state was registered at:
  [  313.402899]   .lock_acquire+0xd0/0x240
  [  313.402903]   ._raw_spin_lock+0x34/0x60
  [  313.402906]   .zstd_get_workspace+0xd0/0x360
  [  313.402908]   .end_compressed_bio_read+0x3b8/0x540
  [  313.402911]   .bio_endio+0x174/0x2c0
  [  313.402914]   .end_workqueue_fn+0x4c/0x70
  [  313.402917]   .normal_work_helper+0x138/0x7e0
  [  313.402920]   .process_one_work+0x324/0x790
  [  313.402922]   .worker_thread+0x68/0x570
  [  313.402925]   .kthread+0x19c/0x1b0
  [  313.402928]   .ret_from_kernel_thread+0x58/0x78
  [  313.402930] irq event stamp: 2629216
  [  313.402933] hardirqs last  enabled at (2629216): [<c0000000009da738>] ._raw_spin_unlock_irq+0x38/0x60
  [  313.402936] hardirqs last disabled at (2629215): [<c0000000009da4c4>] ._raw_spin_lock_irq+0x24/0x70
  [  313.402939] softirqs last  enabled at (2629212): [<c0000000000af9fc>] .irq_enter+0x8c/0xd0
  [  313.402942] softirqs last disabled at (2629213): [<c0000000000afb58>] .irq_exit+0x118/0x170
  [  313.402944]
		 other info that might help us debug this:
  [  313.402945]  Possible unsafe locking scenario:

  [  313.402947]        CPU0
  [  313.402948]        ----
  [  313.402949]   lock(&(&wsm.lock)->rlock);
  [  313.402951]   <Interrupt>
  [  313.402952]     lock(&(&wsm.lock)->rlock);
  [  313.402954]
		  *** DEADLOCK ***

  [  313.402957] 1 lock held by swapper/5/0:
  [  313.402958]  #0: 000000004b612042 ((&wsm.timer)){+.-.}, at: .call_timer_fn+0x0/0x3c0
  [  313.402963]
		 stack backtrace:
  [  313.402967] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 5.1.0-rc7 #1
  [  313.402968] Call Trace:
  [  313.402972] [c0000007fa262e70] [c0000000009b3294] .dump_stack+0xe0/0x15c (unreliable)
  [  313.402975] [c0000007fa262f10] [c000000000125548] .print_usage_bug+0x348/0x390
  [  313.402978] [c0000007fa262fd0] [c000000000125cb4] .mark_lock+0x724/0x930
  [  313.402981] [c0000007fa263080] [c000000000126c20] .__lock_acquire+0xc90/0x16a0
  [  313.402984] [c0000007fa2631b0] [c000000000128040] .lock_acquire+0xd0/0x240
  [  313.402987] [c0000007fa263280] [c0000000009da2b4] ._raw_spin_lock+0x34/0x60
  [  313.402990] [c0000007fa263300] [c00000000054b0b0] .zstd_reclaim_timer_fn+0x40/0x230
  [  313.402993] [c0000007fa2633d0] [c000000000158b38] .call_timer_fn+0xc8/0x3c0
  [  313.402996] [c0000007fa2634a0] [c000000000158f74] .expire_timers+0x144/0x260
  [  313.402999] [c0000007fa263550] [c000000000159178] .run_timer_softirq+0xe8/0x230
  [  313.403002] [c0000007fa263680] [c0000000009db288] .__do_softirq+0x188/0x5d4
  [  313.403004] [c0000007fa263790] [c0000000000afb58] .irq_exit+0x118/0x170
  [  313.403008] [c0000007fa263800] [c000000000028d88] .timer_interrupt+0x158/0x430
  [  313.403012] [c0000007fa2638b0] [c0000000000091d4] decrementer_common+0x134/0x140
  [  313.403017] --- interrupt: 901 at replay_interrupt_return+0x0/0x4
		     LR = .arch_local_irq_restore.part.0+0x68/0x80
  [  313.403020] [c0000007fa263bb0] [c00000000001a3ac] .arch_local_irq_restore.part.0+0x2c/0x80 (unreliable)
  [  313.403024] [c0000007fa263c30] [c0000000007bbbcc] .cpuidle_enter_state+0xec/0x670
  [  313.403027] [c0000007fa263d00] [c0000000000f5130] .call_cpuidle+0x40/0x90
  [  313.403031] [c0000007fa263d70] [c0000000000f554c] .do_idle+0x2dc/0x3a0
  [  313.403034] [c0000007fa263e30] [c0000000000f59ac] .cpu_startup_entry+0x2c/0x30
  [  313.403037] [c0000007fa263ea0] [c000000000045674] .start_secondary+0x644/0x650
  [  313.403041] [c0000007fa263f90] [c00000000000ad5c] start_secondary_prolog+0x10/0x14

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203517
Fixes: 3f93aef5 ("btrfs: add zstd compression level support")
CC: stable@vger.kernel.org # 5.1+
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 60d9f503 upstream.

While logging an inode we follow its ancestors and for each one we mark
it as logged in the current transaction, even if we have not logged it.
As a consequence if we change an attribute of an ancestor, such as the
UID or GID for example, and then explicitly fsync it, we end up not
logging the inode at all despite returning success to user space, which
results in the attribute being lost if a power failure happens after
the fsync.

Sample reproducer:

  $ mkfs.btrfs -f /dev/sdb
  $ mount /dev/sdb /mnt

  $ mkdir /mnt/dir
  $ chown 6007:6007 /mnt/dir

  $ sync

  $ chown 9003:9003 /mnt/dir
  $ touch /mnt/dir/file
  $ xfs_io -c fsync /mnt/dir/file

  # fsync our directory after fsync'ing the new file, should persist the
  # new values for the uid and gid.
  $ xfs_io -c fsync /mnt/dir

  <power failure>

  $ mount /dev/sdb /mnt
  $ stat -c %u:%g /mnt/dir
  6007:6007

    --> should be 9003:9003, the uid and gid were not persisted, despite
        the explicit fsync on the directory prior to the power failure

Fix this by not updating the logged_trans field of ancestor inodes when
logging an inode, since we have not logged them. Let only future calls to
btrfs_log_inode() to mark inodes as logged.

This could be triggered by my recent fsync fuzz tester for fstests, for
which an fstests patch exists titled "fstests: generic, fsync fuzz tester
with fsstress".

Fixes: 12fcfd22 ("Btrfs: tree logging unlink/rename fixes")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 06989c79 upstream.

When syncing the log, the final phase of a fsync operation, we need to
either create a log root's item or update the existing item in the log
tree of log roots, and that depends on the current value of the log
root's log_transid - if it's 1 we need to create the log root item,
otherwise it must exist already and we update it. Since there is no
synchronization between updating the log_transid and checking it for
deciding whether the log root's item needs to be created or updated, we
end up with a tiny race window that results in attempts to update the
item to fail because the item was not yet created:

              CPU 1                                    CPU 2

  btrfs_sync_log()

    lock root->log_mutex

    set log root's log_transid to 1

    unlock root->log_mutex

                                               btrfs_sync_log()

                                                 lock root->log_mutex

                                                 sets log root's
                                                 log_transid to 2

                                                 unlock root->log_mutex

    update_log_root()

      sees log root's log_transid
      with a value of 2

        calls btrfs_update_root(),
        which fails with -EUCLEAN
        and causes transaction abort

Until recently the race lead to a BUG_ON at btrfs_update_root(), but after
the recent commit 7ac1e464 ("btrfs: Don't panic when we can't find a
root key") we just abort the current transaction.

A sample trace of the BUG_ON() on a SLE12 kernel:

  ------------[ cut here ]------------
  kernel BUG at ../fs/btrfs/root-tree.c:157!
  Oops: Exception in kernel mode, sig: 5 [#1]
  SMP NR_CPUS=2048 NUMA pSeries
  (...)
  Supported: Yes, External
  CPU: 78 PID: 76303 Comm: rtas_errd Tainted: G                 X 4.4.156-94.57-default #1
  task: c00000ffa906d010 ti: c00000ff42b08000 task.ti: c00000ff42b08000
  NIP: d000000036ae5cdc LR: d000000036ae5cd8 CTR: 0000000000000000
  REGS: c00000ff42b0b860 TRAP: 0700   Tainted: G                 X  (4.4.156-94.57-default)
  MSR: 8000000002029033 <SF,VEC,EE,ME,IR,DR,RI,LE>  CR: 22444484  XER: 20000000
  CFAR: d000000036aba66c SOFTE: 1
  GPR00: d000000036ae5cd8 c00000ff42b0bae0 d000000036bda220 0000000000000054
  GPR04: 0000000000000001 0000000000000000 c00007ffff8d37c8 0000000000000000
  GPR08: c000000000e19c00 0000000000000000 0000000000000000 3736343438312079
  GPR12: 3930373337303434 c000000007a3a800 00000000007fffff 0000000000000023
  GPR16: c00000ffa9d26028 c00000ffa9d261f8 0000000000000010 c00000ffa9d2ab28
  GPR20: c00000ff42b0bc48 0000000000000001 c00000ff9f0d9888 0000000000000001
  GPR24: c00000ffa9d26000 c00000ffa9d261e8 c00000ffa9d2a800 c00000ff9f0d9888
  GPR28: c00000ffa9d26028 c00000ffa9d2aa98 0000000000000001 c00000ffa98f5b20
  NIP [d000000036ae5cdc] btrfs_update_root+0x25c/0x4e0 [btrfs]
  LR [d000000036ae5cd8] btrfs_update_root+0x258/0x4e0 [btrfs]
  Call Trace:
  [c00000ff42b0bae0] [d000000036ae5cd8] btrfs_update_root+0x258/0x4e0 [btrfs] (unreliable)
  [c00000ff42b0bba0] [d000000036b53610] btrfs_sync_log+0x2d0/0xc60 [btrfs]
  [c00000ff42b0bce0] [d000000036b1785c] btrfs_sync_file+0x44c/0x4e0 [btrfs]
  [c00000ff42b0bd80] [c00000000032e300] vfs_fsync_range+0x70/0x120
  [c00000ff42b0bdd0] [c00000000032e44c] do_fsync+0x5c/0xb0
  [c00000ff42b0be10] [c00000000032e8dc] SyS_fdatasync+0x2c/0x40
  [c00000ff42b0be30] [c000000000009488] system_call+0x3c/0x100
  Instruction dump:
  7f43d378 4bffebb9 60000000 88d90008 3d220000 e8b90000 3b390009 e87a01f0
  e8898e08 e8f90000 4bfd48e5 60000000 <0fe00000> e95b0060 39200004 394a0ea0
  ---[ end trace 8f2dc8f919cabab8 ]---

So fix this by doing the check of log_transid and updating or creating the
log root's item while holding the root's log_mutex.

Fixes: 7237f183 ("Btrfs: fix tree logs parallel sync")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5338e43a upstream.

When replaying a log that contains a new file or directory name that needs
to be added to its parent directory, we end up updating the mtime and the
ctime of the parent directory to the current time after we have set their
values to the correct ones (set at fsync time), efectivelly losing them.

Sample reproducer:

  $ mkfs.btrfs -f /dev/sdb
  $ mount /dev/sdb /mnt

  $ mkdir /mnt/dir
  $ touch /mnt/dir/file

  # fsync of the directory is optional, not needed
  $ xfs_io -c fsync /mnt/dir
  $ xfs_io -c fsync /mnt/dir/file

  $ stat -c %Y /mnt/dir
  1557856079

  <power failure>

  $ sleep 3
  $ mount /dev/sdb /mnt
  $ stat -c %Y /mnt/dir
  1557856082

    --> should have been 1557856079, the mtime is updated to the current
        time when replaying the log

Fix this by not updating the mtime and ctime to the current time at
btrfs_add_link() when we are replaying a log tree.

This could be triggered by my recent fsync fuzz tester for fstests, for
which an fstests patch exists titled "fstests: generic, fsync fuzz tester
with fsstress".

Fixes: e02119d5 ("Btrfs: Add a write ahead tree log to optimize synchronous operations")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dfb4a6f2 upstream.

In case of errors, predicate_parse() goes to the out_free label
to free memory and to return an error code.

However, predicate_parse() does not free the predicates of the
temporary prog_stack array, thence leaking them.

Link: http://lkml.kernel.org/r/20190528154338.29976-1-tomasbortoli@gmail.com

Cc: stable@vger.kernel.org
Fixes: 80765597 ("tracing: Rewrite filter logic to be simpler and faster")
Reported-by: syzbot+6b8e0fb820e570c59e19@syzkaller.appspotmail.com
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
[ Added protection around freeing prog_stack[i].pred ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ef4021fe upstream.

When the user tries to remove a zfcp port via sysfs, we only rejected it if
there are zfcp unit children under the port. With purely automatically
scanned LUNs there are no zfcp units but only SCSI devices. In such cases,
the port_remove erroneously continued. We close the port and this
implicitly closes all LUNs under the port. The SCSI devices survive with
their private zfcp_scsi_dev still holding a reference to the "removed"
zfcp_port (still allocated but invisible in sysfs) [zfcp_get_port_by_wwpn
in zfcp_scsi_slave_alloc]. This is not a problem as long as the fc_rport
stays blocked. Once (auto) port scan brings back the removed port, we
unblock its fc_rport again by design.  However, there is no mechanism that
would recover (open) the LUNs under the port (no "ersfs_3" without
zfcp_unit [zfcp_erp_strategy_followup_success]).  Any pending or new I/O to
such LUN leads to repeated:

  Done: NEEDS_RETRY Result: hostbyte=DID_IMM_RETRY driverbyte=DRIVER_OK

See also v4.10 commit 6f2ce1c6 ("scsi: zfcp: fix rport unblock race
with LUN recovery"). Even a manual LUN recovery
(echo 0 > /sys/bus/scsi/devices/H:C:T:L/zfcp_failed)
does not help, as the LUN links to the old "removed" port which remains
to lack ZFCP_STATUS_COMMON_RUNNING [zfcp_erp_required_act].
The only workaround is to first ensure that the fc_rport is blocked
(e.g. port_remove again in case it was re-discovered by (auto) port scan),
then delete the SCSI devices, and finally re-discover by (auto) port scan.
The port scan includes an fc_rport unblock, which in turn triggers
a new scan on the scsi target to freshly get new pure auto scan LUNs.

Fix this by rejecting port_remove also if there are SCSI devices
(even without any zfcp_unit) under this port. Re-use mechanics from v3.7
commit d99b601b ("[SCSI] zfcp: restore refcount check on port_remove").
However, we have to give up zfcp_sysfs_port_units_mutex earlier in unit_add
to prevent a deadlock with scsi_host scan taking shost->scan_mutex first
and then zfcp_sysfs_port_units_mutex now in our zfcp_scsi_slave_alloc().
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: b62a8d9b ("[SCSI] zfcp: Use SCSI device data zfcp scsi dev instead of zfcp unit")
Fixes: f8210e34 ("[SCSI] zfcp: Allow midlayer to scan for LUNs when running in NPIV mode")
Cc: <stable@vger.kernel.org> #2.6.37+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d27e5e07 upstream.

With this early return due to zfcp_unit child(ren), we don't use the
zfcp_port reference from the earlier zfcp_get_port_by_wwpn() anymore and
need to put it.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: d99b601b ("[SCSI] zfcp: restore refcount check on port_remove")
Cc: <stable@vger.kernel.org> #3.7+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5cdb0ef6 upstream.

In case USB disconnect happens at the moment transmitting workqueue is in
progress the underlying interface may be gone causing a NULL pointer
dereference. Add synchronization of the workqueue destruction with the
detach implementation in core so that the transmitting workqueue is stopped
during detach before the interfaces are removed.

Fix following Oops:

Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = 9e6a802d
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in: nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle
xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4
iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether
usb_serial_simple usbserial cdc_acm brcmfmac brcmutil smsc95xx usbnet
ci_hdrc_imx ci_hdrc ulpi usbmisc_imx 8250_exar 8250_pci 8250 8250_base
libcomposite configfs udc_core
CPU: 0 PID: 7 Comm: kworker/u8:0 Not tainted 4.19.23-00076-g03740aa-dirty #102
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: brcmf_fws_wq brcmf_fws_dequeue_worker [brcmfmac]
PC is at brcmf_txfinalize+0x34/0x90 [brcmfmac]
LR is at brcmf_fws_dequeue_worker+0x218/0x33c [brcmfmac]
pc : [<7f0dee64>]    lr : [<7f0e4140>]    psr: 60010093
sp : ee8abef0  ip : 00000000  fp : edf38000
r10: ffffffed  r9 : edf38970  r8 : edf38004
r7 : edf3e970  r6 : 00000000  r5 : ede69000  r4 : 00000000
r3 : 00000a97  r2 : 00000000  r1 : 0000888e  r0 : ede69000
Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c5387d  Table: 7d03c04a  DAC: 00000051
Process kworker/u8:0 (pid: 7, stack limit = 0x24ec3e04)
Stack: (0xee8abef0 to 0xee8ac000)
bee0:                                     ede69000 00000000 ed56c3e0 7f0e4140
bf00: 00000001 00000000 edf38004 edf3e99c ed56c3e0 80d03d00 edfea43a edf3e970
bf20: ee809880 ee804200 ee971100 00000000 edf3e974 00000000 ee804200 80135a70
bf40: 80d03d00 ee804218 ee809880 ee809894 ee804200 80d03d00 ee804218 ee8aa000
bf60: 00000088 80135d5c 00000000 ee829f00 ee829dc0 00000000 ee809880 80135d30
bf80: ee829f1c ee873eac 00000000 8013b1a0 ee829dc0 8013b07c 00000000 00000000
bfa0: 00000000 00000000 00000000 801010e8 00000000 00000000 00000000 00000000
bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<7f0dee64>] (brcmf_txfinalize [brcmfmac]) from [<7f0e4140>] (brcmf_fws_dequeue_worker+0x218/0x33c [brcmfmac])
[<7f0e4140>] (brcmf_fws_dequeue_worker [brcmfmac]) from [<80135a70>] (process_one_work+0x138/0x3f8)
[<80135a70>] (process_one_work) from [<80135d5c>] (worker_thread+0x2c/0x554)
[<80135d5c>] (worker_thread) from [<8013b1a0>] (kthread+0x124/0x154)
[<8013b1a0>] (kthread) from [<801010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xee8abfb0 to 0xee8abff8)
bfa0:                                     00000000 00000000 00000000 00000000
bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
Code: e1530001 0a000007 e3560000 e1a00005 (05942008)
---[ end trace 079239dd31c86e90 ]---
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a4768663 upstream.

Most Siano devices require an alignment for the response.

Changeset f3be52b0056a ("media: usb: siano: Fix general protection fault in smsusb")
changed the logic with gets such aligment, but it now produces a
sparce warning:

drivers/media/usb/siano/smsusb.c: In function 'smsusb_init_device':
drivers/media/usb/siano/smsusb.c:447:37: warning: 'in_maxp' may be used uninitialized in this function [-Wmaybe-uninitialized]
  447 |   dev->response_alignment = in_maxp - sizeof(struct sms_msg_hdr);
      |                             ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~

The sparse message itself is bogus, but a broken (or fake) USB
eeprom could produce a negative value for response_alignment.

So, change the code in order to check if the result is not
negative.

Fixes: 31e0456d ("media: usb: siano: Fix general protection fault in smsusb")
CC: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 45457c01 upstream.

GCC complains about an apparently uninitialized variable recently
added to smsusb_init_device().  It's a false positive, but to silence
the warning this patch adds a trivial initialization.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: kbuild test robot <lkp@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 31e0456d upstream.

The syzkaller USB fuzzer found a general-protection-fault bug in the
smsusb part of the Siano DVB driver.  The fault occurs during probe
because the driver assumes without checking that the device has both
IN and OUT endpoints and the IN endpoint is ep1.

By slightly rearranging the driver's initialization code, we can make
the appropriate checks early on and thus avoid the problem.  If the
expected endpoints aren't present, the new code safely returns -ENODEV
from the probe routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+53f029db71c19a47325a@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e0feb734 upstream.

If a disconnected device is closed, rio_close() must free
the buffers.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3864d339 upstream.

This driver is using a global variable. It cannot handle more than
one device at a time. The issue has been existing since the dawn
of the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+35f04d136fc975a70da4@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ea261113 upstream.

Without USB_QUIRK_NO_LPM ethernet will not work and rtl8152 will
complain with

    r8152 <device...>: Stop submitting intr, status -71

Adding the quirk resolves this. As the dock is externally powered, this
should not have any drawbacks.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9a5729f6 upstream.

The pointer used to log a failure of usb_register_dev() must
be set before the error is logged.

v2: fix that minor is not available before registration
Signed-off-by: oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+a0cbdbd6d169020c8959@syzkaller.appspotmail.com
Fixes: 7b5cd5fe ("USB: SisUSB2VGA: Convert printk to dev_* macros")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a03ff544 upstream.

The syzkaller USB fuzzer found a slab-out-of-bounds write bug in the
USB core, caused by a failure to check the actual size of a BOS
descriptor.  This patch adds a check to make sure the descriptor is at
least as large as it is supposed to be, so that the code doesn't
inadvertently access memory beyond the end of the allocated region
when assigning to dev->bos->desc->bNumDeviceCaps later on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+71f1e64501a309fcc012@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3ea3091f upstream.

Fix the following sparse context imbalance regression introduced in
a patch that fixed sleeping function called from invalid context bug.

kbuild test robot reported on:

tree/branch: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git  usb-linus

Regressions in current branch:

drivers/usb/usbip/stub_dev.c:399:9: sparse: sparse: context imbalance in 'stub_probe' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:418:13: sparse: sparse: context imbalance in 'stub_disconnect' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:464:1-10: second lock on line 476

Error ids grouped by kconfigs:

recent_errors
├── i386-allmodconfig
│   └── drivers-usb-usbip-stub_dev.c:second-lock-on-line
├── x86_64-allmodconfig
│   ├── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_disconnect-different-lock-contexts-for-basic-block
│   └── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_probe-different-lock-contexts-for-basic-block
└── x86_64-allyesconfig
    └── drivers-usb-usbip-stub_dev.c:second-lock-on-line

This is a real problem in an error leg where spin_lock() is called on an
already held lock.

Fix the imbalance in stub_probe() and stub_disconnect().
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fixes: 0c9e8b3c ("usbip: usbip_host: fix BUG: sleeping function called from invalid context")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0c9e8b3c upstream.

stub_probe() and stub_disconnect() call functions which could call
sleeping function in invalid context whil holding busid_lock.

Fix the problem by refining the lock holds to short critical sections
to change the busid_priv fields. This fix restructures the code to
limit the lock holds in stub_probe() and stub_disconnect().

stub_probe():

[15217.927028] BUG: sleeping function called from invalid context at mm/slab.h:418
[15217.927038] in_atomic(): 1, irqs_disabled(): 0, pid: 29087, name: usbip
[15217.927044] 5 locks held by usbip/29087:
[15217.927047]  #0: 0000000091647f28 (sb_writers#6){....}, at: vfs_write+0x191/0x1c0
[15217.927062]  #1: 000000008f9ba75b (&of->mutex){....}, at: kernfs_fop_write+0xf7/0x1b0
[15217.927072]  #2: 00000000872e5b4b (&dev->mutex){....}, at: __device_driver_lock+0x3b/0x50
[15217.927082]  #3: 00000000e74ececc (&dev->mutex){....}, at: __device_driver_lock+0x46/0x50
[15217.927090]  #4: 00000000b20abbe0 (&(&busid_table[i].busid_lock)->rlock){....}, at: get_busid_priv+0x48/0x60 [usbip_host]
[15217.927103] CPU: 3 PID: 29087 Comm: usbip Tainted: G        W         5.1.0-rc6+ #40
[15217.927106] Hardware name: Dell Inc. OptiPlex 790/0HY9JP, BIOS A18 09/24/2013
[15217.927109] Call Trace:
[15217.927118]  dump_stack+0x63/0x85
[15217.927127]  ___might_sleep+0xff/0x120
[15217.927133]  __might_sleep+0x4a/0x80
[15217.927143]  kmem_cache_alloc_trace+0x1aa/0x210
[15217.927156]  stub_probe+0xe8/0x440 [usbip_host]
[15217.927171]  usb_probe_device+0x34/0x70

stub_disconnect():

[15279.182478] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:908
[15279.182487] in_atomic(): 1, irqs_disabled(): 0, pid: 29114, name: usbip
[15279.182492] 5 locks held by usbip/29114:
[15279.182494]  #0: 0000000091647f28 (sb_writers#6){....}, at: vfs_write+0x191/0x1c0
[15279.182506]  #1: 00000000702cf0f3 (&of->mutex){....}, at: kernfs_fop_write+0xf7/0x1b0
[15279.182514]  #2: 00000000872e5b4b (&dev->mutex){....}, at: __device_driver_lock+0x3b/0x50
[15279.182522]  #3: 00000000e74ececc (&dev->mutex){....}, at: __device_driver_lock+0x46/0x50
[15279.182529]  #4: 00000000b20abbe0 (&(&busid_table[i].busid_lock)->rlock){....}, at: get_busid_priv+0x48/0x60 [usbip_host]
[15279.182541] CPU: 0 PID: 29114 Comm: usbip Tainted: G        W         5.1.0-rc6+ #40
[15279.182543] Hardware name: Dell Inc. OptiPlex 790/0HY9JP, BIOS A18 09/24/2013
[15279.182546] Call Trace:
[15279.182554]  dump_stack+0x63/0x85
[15279.182561]  ___might_sleep+0xff/0x120
[15279.182566]  __might_sleep+0x4a/0x80
[15279.182574]  __mutex_lock+0x55/0x950
[15279.182582]  ? get_busid_priv+0x48/0x60 [usbip_host]
[15279.182587]  ? reacquire_held_locks+0xec/0x1a0
[15279.182591]  ? get_busid_priv+0x48/0x60 [usbip_host]
[15279.182597]  ? find_held_lock+0x94/0xa0
[15279.182609]  mutex_lock_nested+0x1b/0x20
[15279.182614]  ? mutex_lock_nested+0x1b/0x20
[15279.182618]  kernfs_remove_by_name_ns+0x2a/0x90
[15279.182625]  sysfs_remove_file_ns+0x15/0x20
[15279.182629]  device_remove_file+0x19/0x20
[15279.182634]  stub_disconnect+0x6d/0x180 [usbip_host]
[15279.182643]  usb_unbind_device+0x27/0x60
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7aa1bb2f upstream.

With defective USB sticks we see the following error happen:
usb 1-3: new high-speed USB device number 6 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: device descriptor read/64, error -71
usb 1-3: new high-speed USB device number 7 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: unable to get BOS descriptor set
usb 1-3: New USB device found, idVendor=0781, idProduct=5581
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008

This comes from the following place:
[ 1660.215380] IP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.222092] PGD 0 P4D 0
[ 1660.224918] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 1660.425520] CPU: 1 PID: 38 Comm: kworker/1:1 Tainted: P     U  W  O    4.14.67-apl #1
[ 1660.434277] Workqueue: usb_hub_wq hub_event [usbcore]
[ 1660.439918] task: ffffa295b6ae4c80 task.stack: ffffad4580150000
[ 1660.446532] RIP: 0010:xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.453821] RSP: 0018:ffffad4580153c70 EFLAGS: 00010046
[ 1660.459655] RAX: 0000000000000000 RBX: ffffa295b4d7c000 RCX: 0000000000000002
[ 1660.467625] RDX: 0000000000000002 RSI: ffffffff984a55b2 RDI: ffffffff984a55b2
[ 1660.475586] RBP: ffffad4580153cc8 R08: 0000000000d6520a R09: 0000000000000001
[ 1660.483556] R10: ffffad4580a004a0 R11: 0000000000000286 R12: ffffa295b4d7c000
[ 1660.491525] R13: 0000000000010648 R14: ffffa295a84e1800 R15: 0000000000000000
[ 1660.499494] FS:  0000000000000000(0000) GS:ffffa295bfc80000(0000) knlGS:0000000000000000
[ 1660.508530] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1660.514947] CR2: 0000000000000008 CR3: 000000025a114000 CR4: 00000000003406a0
[ 1660.522917] Call Trace:
[ 1660.525657]  usb_set_usb2_hardware_lpm+0x3d/0x70 [usbcore]
[ 1660.531792]  usb_disable_device+0x242/0x260 [usbcore]
[ 1660.537439]  usb_disconnect+0xc1/0x2b0 [usbcore]
[ 1660.542600]  hub_event+0x596/0x18f0 [usbcore]
[ 1660.547467]  ? trace_preempt_on+0xdf/0x100
[ 1660.552040]  ? process_one_work+0x1c1/0x410
[ 1660.556708]  process_one_work+0x1d2/0x410
[ 1660.561184]  ? preempt_count_add.part.3+0x21/0x60
[ 1660.566436]  worker_thread+0x2d/0x3f0
[ 1660.570522]  kthread+0x122/0x140
[ 1660.574123]  ? process_one_work+0x410/0x410
[ 1660.578792]  ? kthread_create_on_node+0x60/0x60
[ 1660.583849]  ret_from_fork+0x3a/0x50
[ 1660.587839] Code: 00 49 89 c3 49 8b 84 24 50 16 00 00 8d 4a ff 48 8d 04 c8 48 89 ca 4c 8b 10 45 8b 6a 04 48 8b 00 48 89 45 c0 49 8b 86 80 03 00 00 <48> 8b 40 08 8b 40 03 0f 1f 44 00 00 45 85 ff 0f 84 81 01 00 00
[ 1660.608980] RIP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] RSP: ffffad4580153c70
[ 1660.617921] CR2: 0000000000000008

Tracking this down shows that udev->bos is NULL in the following code:
(xhci.c, in xhci_set_usb2_hardware_lpm)
	field = le32_to_cpu(udev->bos->ext_cap->bmAttributes);  <<<<<<< here

	xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",
			enable ? "enable" : "disable", port_num + 1);

	if (enable) {
		/* Host supports BESL timeout instead of HIRD */
		if (udev->usb2_hw_lpm_besl_capable) {
			/* if device doesn't have a preferred BESL value use a
			 * default one which works with mixed HIRD and BESL
			 * systems. See XHCI_DEFAULT_BESL definition in xhci.h
			 */
			if ((field & USB_BESL_SUPPORT) &&
			    (field & USB_BESL_BASELINE_VALID))
				hird = USB_GET_BESL_BASELINE(field);
			else
				hird = udev->l1_params.besl;

The failing case is when disabling LPM. So it is sufficient to avoid
access to udev->bos by moving the instruction into the "enable" clause.

Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f7fac17c upstream.

Xhci_handshake() implements the algorithm already captured by
readl_poll_timeout_atomic(). Convert the former to use the latter to
avoid repetition.

Turned out this patch also fixes a bug on the AMD Stoneyridge platform
where usleep(1) sometimes takes over 10ms.
This means a 5 second timeout can easily take over 15 seconds which will
trigger the watchdog and reboot the system.

[Add info about patch fixing a bug to commit message -Mathias]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c1a145a3 upstream.

Commit 597c56e3 ("xhci: update bounce buffer with correct sg num")
caused the following build warnings:

drivers/usb/host/xhci-ring.c:676:19: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'size_t {aka unsigned int}' [-Wformat=]

Use %zu for printing size_t type in order to fix the warnings.

Fixes: 597c56e3 ("xhci: update bounce buffer with correct sg num")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>