- 11 Aug, 2010 40 commits
-
-
Pawel Osciak authored
The following problems were found in the above situation: sfb->windows[win] was being assigned at the end of s3c_fb_probe_win only. This resulted in passing a NULL to s3c_fb_release_win if probe_win returned early and a memory leak. dma_free_writecombine does not allow its third argument to be NULL. fb_dealloc_cmap does not verify whether its argument is not NULL. Signed-off-by:
Pawel Osciak <p.osciak@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Cc: InKi Dae <inki.dae@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Ben Dooks authored
Remove the palette setup code from the header files and put it into the main driver. Signed-off-by:
Ben Dooks <ben-linux@fluff.org> Signed-off-by:
-
Ben Dooks authored
Update the variant and window variant structures with the necessary changes to support the older style of hardware where these are not in the same place. Add the support for the s3c2443/s3c2416 hardware by using the platform-device s3c2443 to cover both, and add the initialisation data for these. Also change to including just the v4 header files for the moment until the last of the merging of these is sorted out. Signed-off-by:
-
Ben Dooks authored
Remove the various header files that configure this driver and use the platform device name to select the correct configuration at probe time. Currently this does not remove the header files, only updates the driver and the relevant platform files. Signed-off-by:
-
Ben Dooks authored
The driver clears all windows, but also sets the windows' colour key controls at the same time. However, the last window does not have these registers as it is always blended into the previous window. Move the colour key initialisation into the probe, and run it for only nr_win-1 windows. Signed-off-by:
-
InKi Dae authored
It has been working fine at 16bpp but in case of pixel format more then 24bpp it would occur distortedness situation on that mode. so this patch set the word swap control bit of WINCONx to 1 as default value. but it should be set to 0 in case that each ENLOCAL bit of WINCON0 ~ 2 registers is enabled. this issue would be solved with local path feature soon. Signed-off-by:
InKi Dae <inki.dae@samsung.com> Reviewed-by: KyungMin Park <kyungmin.park.samsung.com> Signed-off-by:
-
InKi Dae authored
s5pv210 has five window layers (window0 ~ 4), among them, window0 ~ 2 could be used for local path with fimc(capture device) and fimd writeback feature so this patch makes default window layer for UI to be set at machine code. Signed-off-by:
-
Ben Dooks authored
As suggested by Marek Szyprowski, we should make the driver depend on the configuration currently being used to build the platform device into the kernel. Signed-off-by:
-
Denys Vlasenko authored
Replaced !strlen(str) check with !str[0]. Removed the variable which was used solely to store strlen result. Signed-off-by:
Denys Vlasenko <vda.linux@googlemail.com> Signed-off-by:
-
Denys Vlasenko authored
This patch uninlines four similar functions, foo_update_attr(), in four fbcon-related files. These functions contain loops, two of theam have _nested_ loops, and they have more than one callsite each. I think they should not be inlined. Signed-off-by:
-
Denys Vlasenko authored
This function's body is good two screenfuls and it has six callsites. No apparent reason why it is marked inline. Signed-off-by:
-
Henrik Kretzschmar authored
Remove 43 section mismatches by moving the two structures efifb_defined and efifb_fix from .init.data to .devinit.data. Also the two structure arrays dmi_system_table[] and dmi_list[] have been moved from .data to .init.rodata and .init.data, which saves, if built-in, some space. On x86_64 'size -A' showed that these sections changed size: efifb.o: section size-old size-new .data 1200 688 .init.data 7840 512 .init.rodata 0 7568 .devinit.data 0 256 Total 11927 11911 Signed-off-by:
Henrik Kretzschmar <henne@nachtwindheim.de> Cc: Peter Jones <pjones@redhat.com> Signed-off-by:
-
Gregory Bean authored
Add support for Semtech SX150-series I2C GPIO expanders. Compatible models include: 8 bits: sx1508q 16 bits: sx1509q Signed-off-by:
Gregory Bean <gbean@codeaurora.org> Cc: David Brownell <david-b@pacbell.net> Cc: Jean Delvare <khali@linux-fr.org> Cc: Trilok Soni <tsoni@codeaurora.org> Signed-off-by:
-
Daniel Gl?ckner authored
The pca953x driver requires the use of threaded irqs as its irq demultiplexer can sleep. Our irq handler can be called from any context, so use request_any_context_irq to allow threaded irqs as well. Signed-off-by:
Daniel Gl?ckner <dg@emlix.com> Reported-by:
Ian Jeffray <ian@jeffray.co.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
-
Daniel Gl?ckner authored
As sysfs_notify_dirent has been made irq safe, there is no reason to not call it directly from irq. With the work_struct removed, the remaining element in poll_desc is a sysfs_dirent pointer which may not be NULL. We can therefore store it directly in the idr and pass it as context to the irq handler. Most part of the patch deals with renaming defines and variables to reflect their new use without functional change. I also took the opportunity to initialize the idr statically. Signed-off-by:
-
David Brownell authored
Be more consistent about runtime programming interface abuse warnings, which can reduce some confusion and trigger bugfixes. Based on an observation and patch from Jani Nikula. Also update doc to highlight some sleeping-call issues and to match some recent changes. Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Cc: Jani Nikula <ext-jani.1.nikula@nokia.com> Cc: "Ryan Mallon" <ryan@bluewatersys.com> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
Provide sane defaults for pcf857x, so the driver can be used w/o providing platform data (and thus can be simply bound via OF tree). Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <david-b@pacbell.net> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by:
-
Marc Kleine-Budde authored
The gpios on the max730x chips have support for internal pullups while in input mode. This patch adds support for configuring these pullups via platform data. A new member ("input_pullup_active") to the platform data struct is introduced. A set bit in this variable activates the pullups while the respective port is in input mode. This is a compatible enhancement since unset bits lead to disables pullups which was the default in the original driver. _Note_: the 4 lowest bits in "input_pullup_active" are unused because the first 4 ports of the controller are not used, too. Signed-off-by:Marc Kleine-Budde <mkl@pengutronix.de> Reviewed-by:
Wolfram Sang <w.sang@pengutronix.de> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
-
Geert Uytterhoeven authored
The Ricoh RP5C01 RTC contains 26 x 4 bits of NVRAM. Provide access to it via a sysfs "nvram" attribute file. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Cc: Wan ZongShun <mcuos.com@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Christian Dietrich authored
Because CONFIG_PM is a precondition to CONFIG_ACPI, the ifdef CONFIG_PM within ifdef CONFIG_ACPI is redundant. Signed-off-by:
Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de> Acked-by:
Wan ZongShun <mcuos.com@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Roman Fietze authored
Mask out PM flag when reading the hour, always set MIL bit when writing the hour. Signed-off-by:
Roman Fietze <roman.fietze@telemotive.de> Acked-by:
-
Roy Zang authored
Add a driver for the DS3232 RTC chip via the I2C bus. Alarms are not supported in this version of the driver. [akpm@linux-foundation.org: fix Kconfig help text] Signed-off-by:
Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by:
Jingchang Lu <b22599@freescale.com> Signed-off-by:
Srikanth Srinivasan <srikanth.srinivasan@freescale.com> Signed-off-by:
Roy Zang <tie-fei.zang@freescale.com> Acked-by:
-
Wan ZongShun authored
Remove unused local variable. Signed-off-by:
-
Wan ZongShun authored
This patch does two modifications: (1) Adjust enable/disable IRQs location,enable it after rtc registration and disable it prior to unregistration. (2) Put 'platform_set_drvdata(pdev, nuc900_rtc)' in front of rtc registration still be safety, though there is no need to do this, when I move enable irq after rtc registration, I think still put 'platform_set_drvdata' before rtc registration that would be a good habit. Signed-off-by: -
Wan ZongShun authored
Make returning time checking function valid. In spite of using the 'rtc_valid_tm', nevertheless, the read time function omits its returning value, that means the 'rtc_valid_tm' is useless here. Signed-off-by:
-
Wan ZongShun authored
Use rtc_valid_tm() to check the returned struct rtc_time *tm, to avoid returning a wrong tm value. Signed-off-by:
-
Wan ZongShun authored
Use rtc_valid_tm to check the returned struct rtc_time *tm, to avoid returning a wrong tm value. Signed-off-by:
-
Wan ZongShun authored
Use rtc_valid_tm() to check returning tm for max6900, it can avoid returning wrong tm value. Signed-off-by:
Dale Farnsworth <dale@farnsworth.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Wan ZongShun authored
Use rtc_valid_tm() to check returned struct rtc_time *tm - it can avoid returning wrong tm value. Signed-off-by:
-
Roman Fietze authored
- derived from rtc-pcf8563 - no SRAM driver Signed-off-by:
-
Baruch Siach authored
This driver is based on code from Freescale which accompanies their i.MX25 PDK board, with some cleanup. Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Sascha Hauer <kernel@pengutronix.de> Acked-by:
-
Huang Weiyi authored
Signed-off-by:
Huang Weiyi <weiyi.huang@gmail.com> Acked-by:
-
Wan ZongShun authored
We shouldn't implement private ops->ioctl() unless absolutely necessary. pxa series RTC driver's ioctl() is unnecessary, since RTC subsystem has implement the ioctl() very well,so we can only use the API of '.alarm_irq_enable' and '.update_irq_enable' to do enable irq action. Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Acked-by:
Eric Miao <eric.y.miao@gmail.com> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Sergey Matyukevich authored
- add sanity check for alarm data in fm3130_probe - fix fm3130_set_alarm. According to the datasheet, setting match bit '0' indicates that the corresponding alarm field will be used in the match process - add operation alarm_irq_enable operation which is responsible for handling RTC_AIE_ON, RTC_AIE_OFF ioctls - remove clearing of AF bit after reading rtc/alarm control register: according to datasheet this bit is cleared anyway when rtc/alarm control register is read [akpm@linux-foundation.org: make fm3130_alarm_irq_enable() static, fix comment layout] Signed-off-by:
Sergey Matyukevich <geomatsi@gmail.com> Acked-by:
Sergey Lapin <slapin@ossfans.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Wan ZongShun authored
Remove six unused fields from `struct rtc_plat_data'. Signed-off-by:
-
Wan ZongShun authored
Signed-off-by:
-
Wan ZongShun authored
pxa_rtc.rtc_alarm is unused. Signed-off-by:
-
Graham Gower authored
Signed-off-by:
Graham Gower <graham.gower@gmail.com> Acked-by:
-
Wan ZongShun authored
When a user application wants to set the rtc time, the RTC subsystem takes advantage of 'rtc_valid_tm(tm)' to check 'rtc_time *tm' value validity, it make sure the 'tm->tm_year' is larger than 70,so if '70< tm_year < 100', the '(settm->tm_year - 100)' will be negative. ' Setting the negative value to hardware register will be invalid, so I add the 'if' condition to make sure set a valid value to register. Signed-off-by:
-
Wan ZongShun authored
- add an mdelay(1) to the polling loop to cause less frequent access to the hardware register. - change the return value from ENODEV to EPERM if the loop timed out. I think the 'Operation not permitted' description is more suitable for the meaning of 'check_rtc_access_enable()' function, it just be used to judge rtc access operation is permitted or not. Signed-off-by:
-
