Add support for creating PPPoE filters in switchdev mode. Add support
for parsing PPPoE and PPP-specific tc options: pppoe_sid and ppp_proto.

Example filter:
tc filter add dev $PF1 ingress protocol ppp_ses prio 1 flower pppoe_sid \
    1234 ppp_proto ip skip_sw action mirred egress redirect dev $VF1_PR

Changes in iproute2 are required to use the new fields.

ICE COMMS DDP package is required to create a filter as it contains PPPoE
profiles. Added a warning message when loaded DDP package does not contain
required profiles.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Allow to offload PPPoE filters by adding flow_rule_match_pppoe.
Drivers can extract PPPoE specific fields from now on.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add support for PPPoE specific fields for tc-flower.
Those fields can be provided only when protocol was set
to ETH_P_PPP_SES. Defines, dump, load and set are being done here.

Overwrite basic.n_proto only in case of PPP_IP and PPP_IPV6,
otherwise leave it as ETH_P_PPP_SES.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Allow to dissect PPPoE specific fields which are:
- session ID (16 bits)
- ppp protocol (16 bits)
- type (16 bits) - this is PPPoE ethertype, for now only
  ETH_P_PPP_SES is supported, possible ETH_P_PPP_DISC
  in the future

The goal is to make the following TC command possible:

  # tc filter add dev ens6f0 ingress prio 1 protocol ppp_ses \
      flower \
        pppoe_sid 12 \
        ppp_proto ip \
      action drop

Note that only PPPoE Session is supported.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Subbaraya Sundeep says:

====================
Octeontx2 minor tc fixes

This patch set fixes two problems found in tc code
wrt to ratelimiting and when installing UDP/TCP filters.

Patch 1: CN10K has different register format compared to
CN9xx hence fixes that.
Patch 2: Check flow mask also before installing a src/dst
port filter, otherwise installing for one port installs for other one too.
====================

Link: https://lore.kernel.org/r/1658650874-16459-1-git-send-email-sbhatta@marvell.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Check the mask for non-zero value before installing tc filters
for L4 source and destination ports. Otherwise installing a
filter for source port installs destination port too and
vice-versa.

Fixes: 1d4d9e42 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

NIX_AF_TLXX_PIR/CIR register format has changed from OcteonTx2
to CN10K. CN10K supports larger burst size. Fix burst exponent
and burst mantissa configuration for CN10K.

Also fixed 'maxrate' from u32 to u64 since 'police.rate_bytes_ps'
passed by stack is also u64.

Fixes: e638a83f ("octeontx2-pf: TC_MATCHALL egress ratelimiting offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Delete the redundant word 'in'.
Signed-off-by: wangjianli <wangjianli@cdjrlc.com>
Link: https://lore.kernel.org/r/20220724075207.21080-1-wangjianli@cdjrlc.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Delete the redundant word 'in'.
Signed-off-by: wangjianli <wangjianli@cdjrlc.com>
Link: https://lore.kernel.org/r/20220724074746.19550-1-wangjianli@cdjrlc.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Christian Marangi says:

====================
Add MTU change with stmmac interface running

This series is to permit MTU change while the interface is running.
Major rework are needed to permit to allocate a new dma conf based on
the new MTU before applying it. This is to make sure there is enough
space to allocate all the DMA queue before releasing the stmmac driver.

This was tested with a simple way to stress the network while the
interface is running.

2 ssh connection to the device:
- One generating simple traffic with while true; do free; done
- The other making the mtu change with a delay of 1 second

The connection is correctly stopped and recovered after the MTU is changed.

The first 2 patch of this series are minor fixup that fix problems
presented while testing this. One fix a problem when we renable a queue
while we are generating a new dma conf. The other is a corner case that
was notice while stressing the driver and turning down the interface while
there was some traffic.

(this is a follow-up of a simpler patch that wanted to add the same
feature. It was suggested to first try to check if it was possible to
apply the new configuration. Posting as RFC as it does major rework for
the new concept of DMA conf)
====================

Link: https://lore.kernel.org/r/20220723142933.16030-1-ansuelsmth@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Remove the limitation where the interface needs to be down to change
MTU by releasing and opening the stmmac driver to set the new MTU.
Also call the set_filter function to correctly init the port.
This permits to remove the EBUSY error while the ethernet port is
running permitting a correct MTU change if for example a DSA request
a MTU change for a switch CPU port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Rework the driver to generate the stmmac dma_conf before stmmac_open.
This permits a function to first check if it's possible to allocate a
new dma_config and then pass it directly to __stmmac_open and "open" the
interface with the new configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Move dma buf conf to dedicated struct. This in preparation for code
rework that will permit to allocate separate dma_conf without affecting
the priv struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Disable all queues and disconnect before tx_disable in stmmac_release to
prevent a corner case where packet may be still queued at the same time
tx_disable is called resulting in kernel panic if some packet still has
to be processed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Move queue reset to dedicated functions. This aside from a simple
cleanup is also required to allocate a dma conf without resetting the tx
queue while the device is temporarily detached as now the reset is not
part of the dma init function and can be done later in the code flow.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

delete extra space and tab in blank line, there is no functional change.
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Link: https://lore.kernel.org/r/20220723073222.2961602-1-williamsukatube@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-next-2022-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Kalle Valo says:

====================
wireless-next patches for v5.20

Third set of patches for v5.20. MLO work continues and we have a lot
of stack changes due to that, including driver API changes. Not much
driver patches except on mt76.

Major changes:

cfg80211/mac80211
 - more prepartion for Wi-Fi 7 Multi-Link Operation (MLO) support,
   works with one link now
 - align with IEEE Draft P802.11be_D2.0
 - hardware timestamps for receive and transmit

mt76
 - preparation for new chipset support
 - ACPI SAR support

* tag 'wireless-next-2022-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (254 commits)
  wifi: mac80211: fix link data leak
  wifi: mac80211: mlme: fix disassoc with MLO
  wifi: mac80211: add macros to loop over active links
  wifi: mac80211: remove erroneous sband/link validation
  wifi: mac80211: mlme: transmit assoc frame with address translation
  wifi: mac80211: verify link addresses are different
  wifi: mac80211: rx: track link in RX data
  wifi: mac80211: optionally implement MLO multicast TX
  wifi: mac80211: expand ieee80211_mgmt_tx() for MLO
  wifi: nl80211: add MLO link ID to the NL80211_CMD_FRAME TX API
  wifi: mac80211: report link ID to cfg80211 on mgmt RX
  wifi: cfg80211: report link ID in NL80211_CMD_FRAME
  wifi: mac80211: add hardware timestamps for RX and TX
  wifi: cfg80211: add hardware timestamps to frame RX info
  wifi: cfg80211/nl80211: move rx management data into a struct
  wifi: cfg80211: add a function for reporting TX status with hardware timestamps
  wifi: nl80211: add RX and TX timestamp attributes
  wifi: ieee80211: add helper functions for detecting TM/FTM frames
  wifi: mac80211_hwsim: handle links for wmediumd/virtio
  wifi: mac80211: sta_info: fix link_sta insertion
  ...
====================

Link: https://lore.kernel.org/r/20220725174547.EA465C341C6@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

These properties are inherited from ethernet-controller.yaml.
This fixes the dt_binding_check warning:
imx8mm-tqma8mqml-mba8mx.dt.yaml: ethernet@30be0000: 'nvmem-cell-names',
'nvmem-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220720063924.1412799-1-alexander.stein@ew.tq-group.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

ath.git patches for v5.20. One fix and rest minor cleanup.

Tony Nguyen says:

====================
40GbE Intel Wired LAN Driver Updates 2022-07-22

This series contains updates to i40e and iavf drivers.

Przemyslaw adds a helper function for determining whether TC MQPRIO is
enabled for i40e.

Avinash utilizes the driver's bookkeeping of filters to check for
duplicate filter before sending the request to the PF for iavf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A typical flow offload scenario for OpenWrt users is routed traffic
received by the wan interface that is redirected to a wlan device
belonging to the lan bridge. Current implementation fails to
fill wdma offload info in mtk_flow_get_wdma_info() since odev device is
the local bridge. Fix the issue running dev_fill_forward_path routine in
mtk_flow_get_wdma_info in order to identify the wlan device.
Tested-by: Paolo Valerio <pvalerio@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Spectrum-2 PTP preparations

This patchset includes various preparations required for Spectrum-2 PTP
support.

Most of the changes are non-functional (e.g., renaming, adding
registers). The only intentional user visible change is in patch #10
where the PHC time is initialized to zero in accordance with the
recommendation of the PTP maintainer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The function mlxsw_sp_ptp_phc_adjfreq() configures MTUTC register to adjust
hardware frequency by a given value.

This configuration will be same for Spectrum-2. In preparation for
Spectrum-2 PTP support, rename the function to not be Spectrum-1 specific.
Later, it will be used for Spectrum-2 also.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum-1 and Spectrum-2 differ in their time stamping capabilities.
The former can be configured to time stamp only a subset of received PTP
events (e.g., only Sync), whereas the latter will time stamp all PTP
events or none.

In preparation for Spectrum-2 PTP support, rename the function that
parses the hardware time stamping configuration upon %SIOCSHWTSTAMP to
be Spectrum-1 specific.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, there is one shared structure that holds the required
structures for PTP clock. Most of the existing fields are relevant only
for Spectrum-1 (cycles, timecounter, and more). Rename the structure to
be specific for Spectrum-1 and align the existing code. Add a common
structure which includes the structures which will be used also for
Spectrum-2. This structure will be returned from clock_init() operation,
as the definition is shared between all ASICs' operations.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, there is one shared structure that holds the required
structures and details for PTP. Most of the existing fields are relevant
only for Spectrum-1 (hash table, lock for hash table, delayed work, and
more). Rename the structure to be specific for Spectrum-1 and align the
existing code. Add a common structure which includes
'struct mlxsw_sp *mlxsw_sp' and will be returned from ptp_init()
operation, as the definition is shared between all ASICs' operations.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the reading of FRC values (high and low) is done using macro
which calls to a function. In addition, to calculate the offset of FRC,
a simple macro is used. This code can be simplified by adding an helper
function and calculating the offset explicitly instead of using an
additional macro for that.

Add the helper function and convert the existing code. This helper will be
used later to read UTC clock.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As lately recommended in the mailing list[1], set the clock to zero time as
part of initialization.

The idea is that when the clock reads 'Jan 1, 1970', then it is clearly
wrong and user will not mistakenly think that the clock is set correctly.
If as part of initialization, the driver sets the clock, user might see
correct date and time (maybe with a small shift) and assume that there
is no need to sync the clock.

Fix the existing code of Spectrum-1 to set the 'timecounter' to zero.

[1]:
https://lore.kernel.org/netdev/20220201191041.GB7009@hoboy.vegasvil.org/Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename the 'read_frc_capable' bit to 'read_clock_capable' since now it can
be both the FRC and UTC clocks.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a resource identifier for maximum number of FIDs so that it could be
later used to query the information from firmware.

In Spectrum-2 and Spectrum-3, the correction field of PTP packets which are
sent as control packets is not updated at egress port. To overcome this
limitation, some packets will be sent as data packets. The header should
include FID, which is supposed to be 'Max FID + port - 1'. As preparation,
add the required resource, to be able to query the value from firmware
later.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the field FID in TX header is defined, but is not used as it is
relevant only for data packets. mlxsw driver currently sends all
host-generated traffic as control packets and not as data packets.

In Spectrum-2 and Spectrum-3, the correction field of PTP packets which
are sent as control packets is not updated at egress port. To overcome this
limitation while adding support for PTP, some packets will be sent as data
packets.

Fix the wrong shift in the definition, to allow using the field later.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The type of time stamp field in the CQE is configured via the
CONFIG_PROFILE command during driver initialization. Add the definition
of the relevant fields to the command's payload and set the type to UTC
for Spectrum-2 and above. This configuration can be done as part of the
preparations to PTP support, as the type of the time stamp will not break
any existing behavior.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add UTC sec and nsec PCI BAR and offset to query firmware command for a
future use.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Completion Queue Element version 2 (CQEv2) includes various metadata
fields of packets.

Add 'time_stamp' and 'time_stamp_type' fields along with functions to
extract the seconds and nanoseconds for a future use.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Spectrum-2, all the packets are time stamped, the MTPCPC register is
used to configure the types of packets that will adjust the correction
field and which port will trap PTP packets.

If ingress correction is set on a port for a given packet type, then
when such a packet is received via the port, the current time stamp is
subtracted from the correction field.

If egress correction is set on a port for a given packet type, then when
such a packet is transmitted via the port, the current time stamp is
added to the correction field.

Assuming the systems is configured correctly, the above means that the
correction field will contain the transient delay between the ports.

Add this register for a future use in order to support PTP in Spectrum-2.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MTUTC register configures the HW UTC counter.

Add the relevant fields and operations to support PTP in Spectrum-2 and
update mlxsw_reg_mtutc_pack() with the new fields for a future use.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The right name of the register is MTPTPT, which refers to Monitoring
Precision Time Protocol Trap Register.

Therefore, rename the function mlxsw_reg_mtptptp_pack() to
mlxsw_reg_mtptpt_pack().
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2022-07-20

1) Don't set DST_NOPOLICY in IPv4, a recent patch made this
   superfluous. From Eyal Birger.

2) Convert alg_key to flexible array member to avoid an iproute2
   compile warning when built with gcc-12.
   From Stephen Hemminger.

3) xfrm_register_km and xfrm_unregister_km do always return 0
   so change the type to void. From Zhengchao Shao.

4) Fix spelling mistake in esp6.c
   From Zhang Jiaming.

5) Improve the wording of comment above XFRM_OFFLOAD flags.
   From Petr Vaněk.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Harini Katakam says:

====================
macb: Add Versal compatible string to Macb driver

Add Versal device support.

v2:
- Sort compatible strings alphabetically in DT bindings.
- Reorganize new config and CAPS order to be cleaner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On Versal TSU clock cannot be disabled irrespective of whether PTP is
used. Hence introduce a new Versal config structure with a "need tsu"
caps flag and check the same in runtime_suspend/resume before cutting
off clocks.

More information on this for future reference:
This is an IP limitation on versions 1p11 and 1p12 when Qbv is enabled
(See designcfg1, bit 3). However it is better to rely on an SoC specific
check rather than the IP version because tsu clk property itself may not
represent actual HW tsu clock on some chip designs.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>