For PMBus chips, modifying one limit register may affect other limits.
Since limits are all cached in the PMBus core driver, related changes
are not reflected in reported limits.

Introduce function to clear the attribute cache. After calling this function,
the core pmbus driver re-reads all cached values.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Some PMBus chips support monitoring an additional non-standard voltage. While
this voltage can in many cases be supported by simulating an additional sensor
page, this does not work in all cases. Specifically, it is problematic if the
data format is linear and the voltage is reported in LINEAR11 format. Since
output voltages use LINEAR16, and the exponent for LINEAR16 data is chip-wide
and fixed, this can result in overflows.

To solve this problem, add support for an additional virtual input voltage,
call it 'vmon', and treat this voltage as input voltage (which, when the chip
supports linear data format, uses LINEAR11).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

So far, attribute memory was allocated by pre-calculating the maximum possible
amount of attributes. Not only does this waste memory, it is also risky because
the calculation might be wrong. It also requires a lot of defines to specify
the maximum number of attributes per class.

Allocate attribute memory using krealloc() instead. That means we have to use
kfree(), since devm_krealloc() does not exist, but that is still less costly
and less risky than trying to predict the number of attributes at the beginning.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Since memory is now allocated with dev_ functions, we no longer need to keep
track of allocated memory. Sensor memory allocation can therefore be
simplified significantly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Boolean handling depends on storing the sensor data index in sensor_device_attr
as part of the index variable. This limits the number of sensor attributes to
256, and means the sensor sequence number actually has to be maintained to be
able to access sensor data from boolean functions.

Rework the code to store sensor pointers in the pmbus_boolean data structure
directly. With this approach, the number of supportable sensors is now
unlimited.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Since memory is now allocated with dev_ functions, we no longer need to keep
track of allocated memory. Memory allocation for booleans and labels can
therefore be simplified substantially by allocating it only as needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This simplifies the code and makes it a bit smaller.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Fix:
ERROR: Macros with multiple statements should be enclosed in a do - while loop

by unwinding the problematic macros.

As a side effect, this patch reduces code size on x86_64 by 160 bytes and bss
size by 64 bytes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Drop error messages due to implementation errors and due to memory allocation
errors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add support for the TI / Burr-Brown INA209 voltage / current / power
monitor.

Cc: Paul Hays <haysp@magma.net>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add support for temp1_min_alarm and temp1_max_alarm
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup; dropped platform data and interrupt support]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The LM73 supports four A/D conversion resolutions.  The default used by
the existing lm73 driver is the chip's default, 11-bit (0.25 C/LSB).
This patch enables changing of this resolution from userspace via the
update_interval sysfs attribute.  Full details on usage are included in
Documentation/hwmon/lm73.
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

While the LM73 is only specified for temperatures from -40 to +150 degrees C,
its power-up minimum and maximum temperature limits are -256 and +255.75
degrees C. For better consistency and to avoid confusion, clamp limits to
the power-up limits and not to -40 / +150 degrees C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Assume that IT8771E and IT8772E are fully compatible with IT8728F.

IT8771E support contributed by Kelly Anderson.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>

Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>

Without this patch, the SHT15 driver may fail silently with a
non-bidirectional data line and/or an input-only clock line.

This patch checks the return value of gpio_direction_* function calls
and returns the error code (if any) to the caller. If an error occurs in
the read work function (work_funct_t), we wake the queue up directly
without updating the data->state flag, to notice the waiter of the I/O
error.

The patch also makes minor cleanups: s/error_ret/unlock for some labels
and uses devm_gpio_request_one() for the clock line.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

SENSORS_LIMIT and clamp_val have the same functionality, so retire SENSORS_LIMIT
as it is no longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>

SENSORS_LIMIT and clamp_val have the same functionality, so retire SENSORS_LIMIT
as it is no longer needed.

The change reduces text size by 26 bytes and bss size by 16 bytes on x86_86
builds.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>

SENSORS_LIMIT and the generic clamp_val have the same functionality,
and clamp_val is more efficient.

This patch reduces text size by 9052 bytes and bss size by 11624 bytes
for x86_64 builds.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Jean Delvare <khali@linux-fr.org>

This patch renames the supply_uV* variables to supply_uv* to avoid
CamelCase as warned by the checkpatch.pl script.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull btrfs fixes from Chris Mason:
 "It turns out that we had two crc bugs when running fsx-linux in a
  loop.  Many thanks to Josef, Miao Xie, and Dave Sterba for nailing it
  all down.  Miao also has a new OOM fix in this v2 pull as well.

  Ilya fixed a regression Liu Bo found in the balance ioctls for pausing
  and resuming a running balance across drives.

  Josef's orphan truncate patch fixes an obscure corruption we'd see
  during xfstests.

  Arne's patches address problems with subvolume quotas.  If the user
  destroys quota groups incorrectly the FS will refuse to mount.

  The rest are smaller fixes and plugs for memory leaks."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (30 commits)
  Btrfs: fix repeated delalloc work allocation
  Btrfs: fix wrong max device number for single profile
  Btrfs: fix missed transaction->aborted check
  Btrfs: Add ACCESS_ONCE() to transaction->abort accesses
  Btrfs: put csums on the right ordered extent
  Btrfs: use right range to find checksum for compressed extents
  Btrfs: fix panic when recovering tree log
  Btrfs: do not allow logged extents to be merged or removed
  Btrfs: fix a regression in balance usage filter
  Btrfs: prevent qgroup destroy when there are still relations
  Btrfs: ignore orphan qgroup relations
  Btrfs: reorder locks and sanity checks in btrfs_ioctl_defrag
  Btrfs: fix unlock order in btrfs_ioctl_rm_dev
  Btrfs: fix unlock order in btrfs_ioctl_resize
  Btrfs: fix "mutually exclusive op is running" error code
  Btrfs: bring back balance pause/resume logic
  btrfs: update timestamps on truncate()
  btrfs: fix btrfs_cont_expand() freeing IS_ERR em
  Btrfs: fix a bug when llseek for delalloc bytes behind prealloc extents
  Btrfs: fix off-by-one in lseek
  ...

Pull cifs fixes from Steve French:
 "Two small cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  fs/cifs/cifs_dfs_ref.c: fix potential memory leakage
  cifs: fix srcip_matches() for ipv6

Pull kvm fixlet from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Emulate dcbf

Pull ARM fixes from Russell King:
 "A number of fixes:

  Patrik found a problem with preempt counting in the VFP assembly
  functions which can cause the preempt count to be upset.

  Nicolas fixed a problem with the parsing of the DT when it straddles a
  1MB boundary.

  Subhash Jadavani reported a problem with sparsemem and our highmem
  support for cache maintanence for DMA areas, and TI found a bug in
  their strongly ordered memory mapping type.

  Also, three fixes by way of Will Deacon's tree from Dave Martin for
  instruction compatibility and Marc Zyngier to fix hypervisor boot mode
  issues."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7629/1: mm: Fix missing XN flag for for MT_MEMORY_SO
  ARM: DMA: Fix struct page iterator in dma_cache_maint() to work with sparsemem
  ARM: 7628/1: head.S: map one extra section for the ATAG/DTB area
  ARM: 7627/1: Predicate preempt logic on PREEMP_COUNT not PREEMPT alone
  ARM: virt: simplify __hyp_stub_install epilog
  ARM: virt: boot secondary CPUs through the right entry point
  ARM: virt: Avoid bx instruction for compatibility with <=ARMv4

Pull ARM SoC fixes from Olof Johansson:
 "Here's a long-pending fixes pull request for arm-soc (I didn't send
  one in the -rc4 cycle).

  The larger deltas are from:

   - A fixup of error paths in the mvsdio driver

   - Header file move for a driver that hadn't been properly converted
     to multiplatform on i.MX, which was causing build failures when
     included

   - Device tree updates for at91 dealing mostly with their new pinctrl
     setup merged in 3.8 and mistakes in those initial configs

  The rest are the normal mix of small fixes all over the place; sunxi,
  omap, imx, mvebu, etc, etc."

* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
  mfd: vexpress-sysreg: Don't skip initialization on probe
  ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
  ARM: vexpress: extend the MPIDR range used for pen release check
  ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
  ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
  ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
  ARM: at91/dts: add macb mii pinctrl config for kizbox
  ARM: at91: rm9200: remake the BGA as default version
  ARM: at91: fix gpios on i2c-gpio for RM9200 DT
  ARM: at91/at91sam9x5 DTS: add SCK USART pins
  ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
  ARM: at91/at91-pinctrl documentation: fix typo and add some details
  ARM: kirkwood: fix missing #interrupt-cells property
  mmc: mvsdio: use devm_ API to simplify/correct error paths.
  clk: mvebu/clk-cpu.c: fix memory leakage
  ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
  ARM: OMAP2+: DT node Timer iteration fix
  ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
  ARM: OMAP2+: fix build break for omapdrm
  ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
  ...

Pull ACPI and power management fixes from Rafael Wysocki:

 - Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.

 - cpufreq regression fixes for AMD processors from Borislav Petkov,
   Stefan Bader, and Matthew Garrett.

 - ACPI cpufreq fix from Thomas Schlichter.

 - cpufreq and devfreq fixes related to incorrect usage of operating
   performance points (OPP) framework and RCU from Nishanth Menon.

 - APEI workaround for incorrect BIOS information from Lans Zhang.

* tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: Add module aliases for acpi-cpufreq
  ACPI: Check MSR valid bit before using P-state frequencies
  PM / devfreq: exynos4_bus: honor RCU lock usage
  PM / devfreq: add locking documentation for recommended_opp
  cpufreq: cpufreq-cpu0: use RCU locks around usage of OPP
  cpufreq: OMAP: use RCU locks around usage of OPP
  ACPI, APEI: Fixup incorrect 64-bit access width firmware bug
  ACPI / processor: Get power info before updating the C-states
  powernow-k8: Add a kconfig dependency on acpi-cpufreq
  ACPI / cpuidle: Fix NULL pointer issues when cpuidle is disabled
  intel_idle: Don't register CPU notifier if we are not running.

Pull regmap fixes from Mark Brown:
 "One more oversight in the debugfs code was reported and fixed, plus a
  documentation fix."

* tag 'regmap-fix-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: fix small typo in regmap_bulk_write comment
  regmap: debugfs: Fix seeking from the cache

Pull slave-dmaengine fixes from Vinod Koul:
 "A few fixes on slave dmanengine.  There are trivial fixes in imx-dma,
  tegra-dma & ioat driver"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: tegra: implement flags parameters for cyclic transfer
  dmaengine: imx-dma: Disable use of hw_chain to fix sg_dma transfers.
  ioat: Fix DMA memory sync direction correct flag

Pill i2c fixes from Wolfram Sang:
 "Here are a few, typical driver fixes for the I2C subsystem"

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c-designware: add missing MODULE_LICENSE
  i2c: omap: fix draining irq handling
  i2c: omap: errata i462: fix incorrect ack for arbitration lost interrupt
  i2c: muxes: fix wrong use of sizeof(ptr)
  i2c: sirf: register i2c_client from dt child-nodes in probe entry
  i2c: mxs: Fix type of error code
  i2c: mxs: Fix misuse init_completion

btrfs_start_delalloc_inodes() locks the delalloc_inodes list, fetches the
first inode, unlocks the list, triggers btrfs_alloc_delalloc_work/
btrfs_queue_worker for this inode, and then it locks the list, checks the
head of the list again. But because we don't delete the first inode that it
deals with before, it will fetch the same inode. As a result, this function
allocates a huge amount of btrfs_delalloc_work structures, and OOM happens.

Fix this problem by splice this delalloc list.
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

The max device number of single profile is 1, not 0 (0 means 'as many as
possible'). Fix it.

Cc: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

First, though the current transaction->aborted check can stop the commit early
and avoid unnecessary operations, it is too early, and some transaction handles
don't end, those handles may set transaction->aborted after the check.

Second, when we commit the transaction, we will wake up some worker threads to
flush the space cache and inode cache. Those threads also allocate some transaction
handles and may set transaction->aborted if some serious error happens.

So we need more check for ->aborted when committing the transaction. Fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

We may access and update transaction->aborted on the different CPUs without
lock, so we need ACCESS_ONCE() wrapper to prevent the compiler from creating
unsolicited accesses and make sure we can get the right value.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

I noticed a WARN_ON going off when adding csums because we were going over
the amount of csum bytes that should have been allowed for an ordered
extent.  This is a leftover from when we used to hold the csums privately
for direct io, but now we use the normal ordered sum stuff so we need to
make sure and check if we've moved on to another extent so that the csums
are added to the right extent.  Without this we could end up with csums for
bytenrs that don't have extents to cover them yet.  Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

For compressed extents, the range of checksum is covered by disk length,
and the disk length is different with ram length, so we need to use disk
length instead to get us the right checksum.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

A user reported a BUG_ON(ret) that occured during tree log replay.  Ret was
-EAGAIN, so what I think happened is that we removed an extent that covered
a bitmap entry and an extent entry.  We remove the part from the bitmap and
return -EAGAIN and then search for the next piece we want to remove, which
happens to be an entire extent entry, so we just free the sucker and return.
The problem is ret is still set to -EAGAIN so we trip the BUG_ON().  The
user used btrfs-zero-log so I'm not 100% sure this is what happened so I've
added a WARN_ON() to catch the other possibility.  Thanks,
Reported-by: Jan Steffens <jan.steffens@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

We drop the extent map tree lock while we're logging extents, so somebody
could come in and merge another extent into this one and screw up our
logging, or they could even remove us from the list which would keep us from
logging the extent or freeing our ref on it, so we need to make sure to not
clear LOGGING until after the extent is logged, and then we can merge it to
adjacent extents.  Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

From Pawel Moll:
- makes the V2P-CA15_A7 (a.k.a. TC2) work with 3.8 kernels
- improves vexpress-sysreg.c behaviour on arm64 platforms

* 'vexpress/fixes' of git://git.linaro.org/people/pawelmoll/linux:
  mfd: vexpress-sysreg: Don't skip initialization on probe
  ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
  ARM: vexpress: extend the MPIDR range used for pen release check