- 11 Aug, 2013 6 commits
-
-
Johannes Berg authored
commit 6b0f3274 upstream. The duplicate retransmission detection code in mac80211 erroneously attempts to do the check for every frame, even frames that don't have a sequence control field or that don't use it (QoS-Null frames.) This is problematic because it causes the code to access data beyond the end of the SKB and depending on the data there will drop packets erroneously. Correct the code to not do duplicate detection for such frames. I found this error while testing AP powersave, it lead to retransmitted PS-Poll frames being dropped entirely as the data beyond the end of the SKB was always zero. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michal Kazior authored
commit a0ec570f upstream. These two events were sent to the default network namespace. This caused AP mode in a non-default netns to not work correctly. Mgmt tx status was multicasted to a different (default) netns instead of the one the AP was in. Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
-
Oleksij Rempel authored
commit dc2a87f5 upstream. Currently we configure harwdare and clock, only after interface start. In this case, if we reload module or reboot PC without configuring adapter, firmware will freeze. There is no software way to reset adpter. This patch add initial configuration and set it in disabled state, to avoid this freeze. Behaviour of this patch should be similar to: ifconfig wlan0 up; ifconfig wlan0 down. Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1Tested-by:
Bo Shi <cnshibo@gmail.com> Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 079a036f upstream. Without this patch the driver waits ~1 ms for the UART to become idle. At 115200n8 this time is (theoretically) enough to transfer 11.5 characters (= 115200 bits/s / (10 Bits/char) * 1ms). As the mxs-auart has a fifo size of 16 characters the clock is gated too early. The problem is worse for lower baud rates. This only happens to really shut down the transmitter in the middle of a transfer if /dev/ttyAPPx isn't opened in userspace (e.g. by a getty) but was at least once (because the bootloader doesn't disable the transmitter). So increase the timeout to 20 ms which should be enough for 9600n8, too. Moreover skip gating the clock if the timeout is elapsed. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Uwe Kleine-König authored
commit d970d7fe upstream. The handler needs to ack the pending events before actually handling them. Otherwise a new event might come in after it it considered non-pending or handled and is acked then without being handled. So this event is only noticed when the next interrupt happens. Without this patch an i.MX28 based machine running an rt-patched kernel regularly hangs during boot. Signed-off-by:
-
Vinod Koul authored
commit a8d30608 upstream. the return value of SNDRV_COMPRESS_VERSION always return default -ENOTTY as the return value was never updated for this call assign return value from put_user() Reported-by:
Haynes <hgeorge@codeaurora.org> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
- 04 Aug, 2013 34 commits
-
-
Greg Kroah-Hartman authored
-
Wanpeng Li authored
commit cea27eb2 upstream. The logic for the memory-remove code fails to correctly account the Total High Memory when a memory block which contains High Memory is offlined as shown in the example below. The following patch fixes it. Before logic memory remove: MemTotal: 7603740 kB MemFree: 6329612 kB Buffers: 94352 kB Cached: 872008 kB SwapCached: 0 kB Active: 626932 kB Inactive: 519216 kB Active(anon): 180776 kB Inactive(anon): 222944 kB Active(file): 446156 kB Inactive(file): 296272 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 7294672 kB HighFree: 5704696 kB LowTotal: 309068 kB LowFree: 624916 kB After logic memory remove: MemTotal: 7079452 kB MemFree: 5805976 kB Buffers: 94372 kB Cached: 872000 kB SwapCached: 0 kB Active: 626936 kB Inactive: 519236 kB Active(anon): 180780 kB Inactive(anon): 222944 kB Active(file): 446156 kB Inactive(file): 296292 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 7294672 kB HighFree: 5181024 kB LowTotal: 4294752076 kB LowFree: 624952 kB [mhocko@suse.cz: fix CONFIG_HIGHMEM=n build] Signed-off-by:
Wanpeng Li <liwanp@linux.vnet.ibm.com> Reviewed-by:
Michal Hocko <mhocko@suse.cz> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> [2.6.24+] Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Zhouping Liu <zliu@redhat.com> Signed-off-by:
-
Michael S. Tsirkin authored
commit cbdadbbf upstream virtio net called virtqueue_enable_cq on RX path after napi_complete, so with NAPI_STATE_SCHED clear - outside the implicit napi lock. This violates the requirement to synchronize virtqueue_enable_cq wrt virtqueue_add_buf. In particular, used event can move backwards, causing us to lose interrupts. In a debug build, this can trigger panic within START_USE. Jason Wang reports that he can trigger the races artificially, by adding udelay() in virtqueue_enable_cb() after virtio_mb(). However, we must call napi_complete to clear NAPI_STATE_SCHED before polling the virtqueue for used buffers, otherwise napi_schedule_prep in a callback will fail, causing us to lose RX events. To fix, call virtqueue_enable_cb_prepare with NAPI_STATE_SCHED set (under napi lock), later call virtqueue_poll with NAPI_STATE_SCHED clear (outside the lock). Reported-by:
Jason Wang <jasowang@redhat.com> Tested-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> [wg: Backported to 3.2] Signed-off-by:
Wolfram Gloger <wmglo@dent.med.uni-muenchen.de> Signed-off-by:
-
Michael S. Tsirkin authored
commit cc229884 upstream. This adds a way to check ring empty state after enable_cb outside any locks. Will be used by virtio_net. Note: there's room for more optimization: caller is likely to have a memory barrier already, which means we might be able to get rid of a barrier here. Deferring this optimization until we do some benchmarking. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Linus Torvalds authored
commit 4f2e2903 upstream. Commit b4cbb197 ("vm: add vm_iomap_memory() helper function") added a helper function wrapper around io_remap_pfn_range(), and every other architecture defined it in <asm/pgtable.h>. The s390 choice of <asm/io.h> may make sense, but is not very convenient for this case, and gratuitous differences like that cause unexpected errors like this: mm/memory.c: In function 'vm_iomap_memory': mm/memory.c:2439:2: error: implicit declaration of function 'io_remap_pfn_range' [-Werror=implicit-function-declaration] Glory be the kbuild test robot who noticed this, bisected it, and reported it to the guilty parties (ie me). Signed-off-by:
-
Steffen Maier authored
commit 9edf7d75 upstream. Commit 64deb6ef "[SCSI] zfcp: Use status_read_buf_num provided by FCP channel" started using a value returned by the channel but only evaluated the value if the fabric link is up. Commit 8d88cf3f "[SCSI] zfcp: Update status read mempool" introduced mempool resizings based on the above value. On setting an FCP device online for the very first time since boot, a new zeroed adapter object is allocated. If the link is down, the number of status read requests remains zero. Since just the config data exchange is incomplete, we proceed with adapter open recovery. However, we unconditionally call mempool_resize with adapter->stat_read_buf_num == 0 in this case. This causes a kernel message "kernel BUG at mm/mempool.c:131!" in process "zfcperp<FCP-device-bus-ID>" with last function mempool_resize in Krnl PSW and zfcp_erp_thread in the Call Trace. Don't evaluate channel values which are invalid on link down. The number of status read requests is always valid, evaluated, and set to a positive minimum greater than zero. The adapter open recovery can proceed and the channel has status read buffers to inform us on a future link up event. While we are not aware of any other code path that could result in mempool resize attempts of size zero, we still also initialize the number of status read buffers to be posted to a static minimum number on adapter object allocation. Backported for 3.4-stable. commit a53c8fab since v3.6-rc1 unified copyright messages, e.g: revise such messages 'Copyright IBM Corporation' as 'Copyright IBM Corp', so updated the messages as a53c8fab did. Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> #2.6.35+ Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Clemens Ladisch authored
commit 0699a73a upstream. Commit 18d62711 (firewire: prevent dropping of completed iso packet header data) was intended to be an obvious bug fix, but libdc1394 and FlyCap2 depend on the old behaviour by ignoring all returned information and thus not noticing that not all packets have been received yet. The result was that the video frame buffers would be saved before they contained the correct data. Reintroduce the old behaviour for old clients. Tested-by:
Stepan Salenikovich <stepan.salenikovich@gmail.com> Tested-by:
Josep Bosch <jep250@gmail.com> Cc: <stable@vger.kernel.org> # 3.4+ Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by:
-
David Vrabel authored
commit 179fbd5a upstream. Unbinding an event channel (either with the ioctl or when the evtchn device is closed) may deadlock because disable_irq() is called with port_user_lock held which is also locked by the interrupt handler. Think of the IOCTL_EVTCHN_UNBIND is being serviced, the routine has just taken the lock, and an interrupt happens. The evtchn_interrupt is invoked, tries to take the lock and spins forever. A quick glance at the code shows that the spinlock is a local IRQ variant. Unfortunately that does not help as "disable_irq() waits for the interrupt handler on all CPUs to stop running. If the irq occurs on another VCPU, it tries to take port_user_lock and can't because the unbind ioctl is holding it." (from David). Hence we cannot depend on the said spinlock to protect us. We could make it a system wide IRQ disable spinlock but there is a better way. We can piggyback on the fact that the existence of the spinlock is to make get_port_user() checks be up-to-date. And we can alter those checks to not depend on the spin lock (as it's protected by u->bind_mutex in the ioctl) and can remove the unnecessary locking (this is IOCTL_EVTCHN_UNBIND) path. In the interrupt handler we cannot use the mutex, but we do not need it. "The unbind disables the irq before making the port user stale, so when you clear it you are guaranteed that the interrupt handler that might use that port cannot be running." (from David). Hence this patch removes the spinlock usage on the teardown path and piggybacks on disable_irq happening before we muck with the get_port_user() data. This ensures that the interrupt handler will never run on stale data. Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [v1: Expanded the commit description a bit] Signed-off-by:
Jonghwan Choi <jhbird.choi@samsung.com> Signed-off-by:
-
NeilBrown authored
commit 0eb25bb0 upstream. We always need to be careful when calling generic_make_request, as it can start a chain of events which might free something that we are using. Here is one place I wasn't careful enough. If the wbio2 is not in use, then it might get freed at the first generic_make_request call. So perform all necessary tests first. This bug was introduced in 3.3-rc3 (24afd80d) and can cause an oops, so fix is suitable for any -stable since then. Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
NeilBrown authored
commit f94c0b66 upstream. If a device in a RAID4/5/6 is being replaced while another is being recovered, then the writes to the replacement device currently don't happen, resulting in corruption when the replacement completes and the new drive takes over. This is because the replacement writes are only triggered when 's.replacing' is set and not when the similar 's.sync' is set (which is the case during resync and recovery - it means all devices need to be read). So schedule those writes when s.replacing is set as well. In this case we cannot use "STRIPE_INSYNC" to record that the replacement has happened as that is needed for recording that any parity calculation is complete. So introduce STRIPE_REPLACED to record if the replacement has happened. For safety we should also check that STRIPE_COMPUTE_RUN is not set. This has a similar effect to the "s.locked == 0" test. The latter ensure that now IO has been flagged but not started. The former checks if any parity calculation has been flagged by not started. We must wait for both of these to complete before triggering the 'replace'. Add a similar test to the subsequent check for "are we finished yet". This possibly isn't needed (is subsumed in the STRIPE_INSYNC test), but it makes it more obvious that the REPLACE will happen before we think we are finished. Finally if a NeedReplace device is not UPTODATE then that is an error. We really must trigger a warning. This bug was introduced in commit 9a3e1101 (md/raid5: detect and handle replacements during recovery.) which introduced replacement for raid5. That was in 3.3-rc3, so any stable kernel since then would benefit from this fix. Reported-by:
qindehua <13691222965@163.com> Tested-by:
qindehua <qindehua@163.com> Signed-off-by:
-
Al Viro authored
commit acfec9a5 upstream. Eric Sandeen has found a nasty livelock in sget() - take a mount(2) about to fail. The superblock is on ->fs_supers, ->s_umount is held exclusive, ->s_active is 1. Along comes two more processes, trying to mount the same thing; sget() in each is picking that superblock, bumping ->s_count and trying to grab ->s_umount. ->s_active is 3 now. Original mount(2) finally gets to deactivate_locked_super() on failure; ->s_active is 2, superblock is still ->fs_supers because shutdown will *not* happen until ->s_active hits 0. ->s_umount is dropped and now we have two processes chasing each other: s_active = 2, A acquired ->s_umount, B blocked A sees that the damn thing is stillborn, does deactivate_locked_super() s_active = 1, A drops ->s_umount, B gets it A restarts the search and finds the same superblock. And bumps it ->s_active. s_active = 2, B holds ->s_umount, A blocked on trying to get it ... and we are in the earlier situation with A and B switched places. The root cause, of course, is that ->s_active should not grow until we'd got MS_BORN. Then failing ->mount() will have deactivate_locked_super() shut the damn thing down. Fortunately, it's easy to do - the key point is that grab_super() is called only for superblocks currently on ->fs_supers, so it can bump ->s_count and grab ->s_umount first, then check MS_BORN and bump ->s_active; we must never increment ->s_count for superblocks past ->kill_sb(), but grab_super() is never called for those. The bug is pretty old; we would've caught it by now, if not for accidental exclusion between sget() for block filesystems; the things like cgroup or e.g. mtd-based filesystems don't have anything of that sort, so they get bitten. The right way to deal with that is obviously to fix sget()... Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Rick Farina (Zero_Chaos) authored
commit fed1f1ed upstream. RT Systems makes many usb serial cables based on the ftdi_sio driver for programming various amateur radios. This patch is a full listing of their current product offerings and should allow these cables to all be recognized. Signed-off-by:
Rick Farina (Zero_Chaos) <zerochaos@gentoo.org> Signed-off-by:
-
Alex Deucher authored
commit 42a21826 upstream. The ProcessAuxChannel table on some rv635 boards assumes the divmul members are initialized to 0 otherwise we get an invalid fb offset since it has a bad mask set when setting the fb base. While here initialize all the atom interpretor elements to 0. Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=60639Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 03ed8cf9 upstream. Hopefully avoid more quirks in the future due to bogus vbios dac data. Signed-off-by:
-
Mark Kettenis authored
commit cef1d00c upstream. Noticed that my old Radeon 7500 hung after printing drm: GPU not posted. posting now... when it wasn't selected as the primary card the BIOS. Some digging revealed that it was hanging in combios_parse_mmio_table() while parsing the ASIC INIT 3 table. Looking at the BIOS ROM for the card, it becomes obvious that there is no ASIC INIT 3 table in the BIOS. The code is just processing random garbage. No surprise it hangs! Why do I say that there is no ASIC INIT 3 table is the BIOS? This table is found through the MISC INFO table. The MISC INFO table can be found at offset 0x5e in the COMBIOS header. But the header is smaller than that. The COMBIOS header starts at offset 0x126. The standard PCI Data Structure (the bit that starts with 'PCIR') lives at offset 0x180. That means that the COMBIOS header can not be larger than 0x5a bytes and therefore cannot contain a MISC INFO table. I looked at a dozen or so BIOS images, some my own, some downloaded from: <http://www.techpowerup.com/vgabios/index.php?manufacturer=ATI&page=1> It is fairly obvious that the size of the COMBIOS header can be found at offset 0x6 of the header. Not sure if it is a 16-bit number or just an 8-bit number, but that doesn't really matter since the tables seems to be always smaller than 256 bytes. So I think combios_get_table_offset() should check if the requested table is present. This can be done by checking the offset against the size of the header. See the diff below. The diff is against the WIP OpenBSD codebase that roughly corresponds to Linux 3.8.13 at this point. But I don't think this bit of the code changed much since then. For what it is worth: Signed-off-by:
Mark Kettenis <kettenis@openbsd.org> Signed-off-by:
-
Alex Deucher authored
commit 34be8c9a upstream. The atom interpreter expects data in LE format, so swap the message buffer as apprioriate. v2: properly handle non-dw aligned byte counts. v3: properly handle remainder Signed-off-by:
-
Mikulas Patocka authored
commit b1bf2de0 upstream. Fix a boundary condition that caused failure for certain device sizes. The problem is reported at http://code.google.com/p/cryptsetup/issues/detail?id=160 For certain device sizes the number of hashes at a specific level was calculated incorrectly. It happens for example for a device with data and metadata block size 4096 that has 16385 blocks and algorithm sha256. The user can test if he is affected by this bug by running the "veritysetup verify" command and also by activating the dm-verity kernel driver and reading the whole block device. If it passes without an error, then the user is not affected. The condition for the bug is: Split the total number of data blocks (data_block_bits) into bit strings, each string has hash_per_block_bits bits. hash_per_block_bits is rounddown(log2(metadata_block_size/hash_digest_size)). Equivalently, you can say that you convert data_blocks_bits to 2^hash_per_block_bits base. If there some zero bit string below the most significant bit string and at least one bit below this zero bit string is set, then the bug happens. The same bug exists in the userspace veritysetup tool, so you must use fixed veritysetup too if you want to use devices that are affected by this boundary condition. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Cc: Milan Broz <gmazyland@gmail.com> Signed-off-by:
Alasdair G Kergon <agk@redhat.com> Signed-off-by:
-
Toshi Kani authored
commit d19f503e upstream. device->driver_data needs to be cleared when releasing its data, mem_device, in an error path of acpi_memory_device_add(). The function evaluates the _CRS of memory device objects, and fails when it gets an unexpected resource or cannot allocate memory. A kernel crash or data corruption may occur when the kernel accesses the stale pointer. Signed-off-by:
Toshi Kani <toshi.kani@hp.com> Reviewed-by:
Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Anton Blanchard authored
commit 0e0ed640 upstream. Module CRCs are implemented as absolute symbols that get resolved by a linker script. We build an intermediate .o that contains an unresolved symbol for each CRC. genksysms parses this .o, calculates the CRCs and writes a linker script that "resolves" the symbols to the calculated CRC. Unfortunately the ppc64 relocatable kernel sees these CRCs as symbols that need relocating and relocates them at boot. Commit d4703aef (module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y) added a hook to reverse the bogus relocations. Part of this patch created a symbol at 0x0: # head -2 /proc/kallsyms 0000000000000000 T reloc_start c000000000000000 T .__start This reloc_start symbol is causing lots of confusion to perf. It thinks reloc_start is a massive function that stretches from 0x0 to 0xc000000000000000 and we get various cryptic errors out of perf, including: problem incrementing symbol count, skipping event This patch removes the reloc_start linker script label and instead defines it as PHYSICAL_START. We also need to wrap it with CONFIG_PPC64 because the ppc32 kernel can set a non zero PHYSICAL_START at compile time and we wouldn't want to subtract it from the CRCs in that case. Signed-off-by:
Anton Blanchard <anton@samba.org> Acked-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Tejun Heo authored
commit bb969619 upstream. sata_inic162x never reached a state where it's reliable enough for production use and data corruption is a relatively common occurrence. Make the driver generate warning about the issues and mark the Kconfig option as experimental. If the situation doesn't improve, we'd be better off making it depend on CONFIG_BROKEN. Let's wait for several cycles and see if the kernel message draws any attention. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Martin Braure de Calignon <braurede@free.fr> Reported-by:
-
Youquan Song authored
commit eac27f04 upstream. There is a patch b55f84e2 "ata_piix: Fix DVD not dectected at some Haswell platforms" to fix an issue of DVD not recognized on Haswell Desktop platform with Lynx Point. Recently, it is also found the same issue at some platformas with Wellsburg PCH. So deliver a similar patch to fix it by disables 32bit PIO in IDE mode. Signed-off-by:
Youquan Song <youquan.song@intel.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 604c499c upstream. We need to make sure that the device is not RO or that the request is not past the number of sectors we want to issue the DISCARD operation for. This fixes CVE-2013-2140. Acked-by:
Jan Beulich <JBeulich@suse.com> Acked-by:
Ian Campbell <Ian.Campbell@citrix.com> [v1: Made it pr_warn instead of pr_debug] Signed-off-by:
-
Josef Bacik authored
commit d29a9f62 upstream. If we stop dropping a root for whatever reason we need to add it back to the dead root list so that we will re-start the dropping next transaction commit. The other case this happens is if we recover a drop because we will add a root without adding it to the fs radix tree, so we can leak it's root and commit root extent buffer, adding this to the dead root list makes this cleanup happen. Thanks, Reported-by:
Alex Lyakas <alex.btrfs@zadarastorage.com> Signed-off-by:
Josef Bacik <jbacik@fusionio.com> Signed-off-by:
-
Josef Bacik authored
commit fec386ac upstream. We aren't setting path->locks[level] when we resume a snapshot deletion which means we won't unlock the buffer when we free the path. This causes deadlocks if we happen to re-allocate the block before we've evicted the extent buffer from cache. Thanks, Reported-by:
-
Ian Abbott authored
commit 69acbaac upstream. Comedi devices can do blocking read() or write() (or poll()) if an asynchronous command has been set up, blocking for data (for read()) or buffer space (for write()). Various events associated with the asynchronous command will wake up the blocked reader or writer (or poller). It is also possible to force the asynchronous command to terminate by issuing a `COMEDI_CANCEL` ioctl. That shuts down the asynchronous command, but does not currently wake up the blocked reader or writer (or poller). If the blocked task could be woken up, it would see that the command is no longer active and return. The caller of the `COMEDI_CANCEL` ioctl could attempt to wake up the blocked task by sending a signal, but that's a nasty workaround. Change `do_cancel_ioctl()` to wake up the wait queue after it returns from `do_cancel()`. `do_cancel()` can propagate an error return value from the low-level comedi driver's cancel routine, but it always shuts the command down regardless, so `do_cancel_ioctl()` can wake up he wait queue regardless of the return value from `do_cancel()`. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
William Gulland authored
commit 2c7b871b upstream. Control transfers have both IN and OUT (or SETUP) packets, so when clearing TT buffers for a control transfer it's necessary to send two HUB_CLEAR_TT_BUFFER requests to the hub. Signed-off-by:
William Gulland <wgulland@google.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Jóhann B. Guðmundsson authored
commit 58fc90db upstream. Signed-off-by:
Jóhann B. Guðmundsson <johannbg@fedoraproject.org> Signed-off-by:
-
Johan Hovold authored
commit 1fad5642 upstream. The driver failed to take the dynamic ids into account when determining the device type and therefore all devices were detected as 2-port devices when using the dynamic-id interface. Match on the usb-serial-driver field instead of doing redundant id-table searches. Reported-by:
Anders Hammarquist <iko@iko.pp.se> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Felipe Balbi authored
commit cdcedd69 upstream. In case we fail our ->udc_start() callback, we should be ready to accept another modprobe following the failed one. We had forgotten to clear dwc->gadget_driver back to NULL and, because of that, we were preventing gadget driver modprobe from being retried. Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Huang Rui authored
commit 1974d494 upstream. Per dwc3 2.50a spec, the is_devspec bit is used to distinguish the Device Endpoint-Specific Event or Device-Specific Event (DEVT). If the bit is 1, the event is represented Device-Specific Event, then use [7:1] bits as Device Specific Event to marked the type. It has 7 bits, and we can see the reserved8_31 variable name which means from 8 to 31 bits marked reserved, actually there are 24 bits not 25 bits between that. And 1 + 7 + 24 = 32, the event size is 4 byes. So in dwc3_event_type, the bit mask should be: is_devspec [0] 1 bit type [7:1] 7 bits reserved8_31 [31:8] 24 bits This patch should be backported to kernels as old as 3.2, that contain the commit 72246da4 "usb: Introduce DesignWare USB3 DRD Driver". Signed-off-by:
Huang Rui <ray.huang@amd.com> Signed-off-by:
-
Sarah Sharp authored
commit 203a8661 upstream. When the host controller fails to respond to an Enable Slot command, and the host fails to respond to the register write to abort the command ring, the xHCI driver will assume the host is dead, and call usb_hc_died(). The USB device's slot_id is still set to zero, and the pointer stored at xhci->devs[0] will always be NULL. The call to xhci_check_args in xhci_free_dev should have caught the NULL virt_dev pointer. However, xhci_free_dev is designed to free the xhci_virt_device structures, even if the host is dead, so that we don't leak kernel memory. xhci_free_dev checks the return value from the generic xhci_check_args function. If the return value is -ENODEV, it carries on trying to free the virtual device. The issue is that xhci_check_args looks at the host controller state before it looks at the xhci_virt_device pointer. It will return -ENIVAL because the host is dead, and xhci_free_dev will ignore the return value, and happily dereference the NULL xhci_virt_device pointer. The fix is to make sure that xhci_check_args checks the xhci_virt_device pointer before it checks the host state. See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for further details. This patch doesn't solve the underlying issue, but will ensure we don't see any more NULL pointer dereferences because of the issue. This patch should be backported to kernels as old as 3.1, that contain the commit 7bd89b40 "xhci: Don't submit commands or URBs to halted hosts." Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by:
Vincent Thiele <vincentthiele@gmail.com> Signed-off-by:
-
Oleksij Rempel authored
commit d66eaf9f upstream. in some cases where device is attched to xhci port and do not responding, for example ath9k_htc with stalled firmware, kernel will crash on ring_doorbell_for_active_rings. This patch check if pointer exist before it is used. This patch should be backported to kernels as old as 2.6.35, that contain the commit e9df17eb "USB: xhci: Correct assumptions about number of rings per endpoint" Signed-off-by:
-
George Cherian authored
commit 07f3cb7c upstream. Xhci controllers with hci_version > 0.96 gives spurious success events on short packet completion. During webcam capture the "ERROR Transfer event TRB DMA ptr not part of current TD" was observed. The same application works fine with synopsis controllers hci_version 0.96. The same issue is seen with Intel Pantherpoint xhci controller. So enabling this quirk in xhci_gen_setup if controller verion is greater than 0.96. For xhci-pci move the quirk to much generic place xhci_gen_setup. Note from Sarah: The xHCI 1.0 spec changed how hardware handles short packets. The HW will notify SW of the TRB where the short packet occurred, and it will also give a successful status for the last TRB in a TD (the one with the IOC flag set). On the second successful status, that warning will be triggered in the driver. Software is now supposed to not assume the TD is not completed until it gets that last successful status. That means we have a slight race condition, although it should have little practical impact. This patch papers over that issue. It's on my long-term to-do list to fix this race condition, but it is a much more involved patch that will probably be too big for stable. This patch is needed for stable to avoid serious log spam. This patch should be backported to kernels as old as 3.0, that contain the commit ad808333 "Intel xhci: Ignore spurious successful event." The patch will have to be modified for kernels older than 3.2, since that kernel added the xhci_gen_setup function for xhci platform devices. The correct conflict resolution for kernels older than 3.2 is to set XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts. Signed-off-by:
George Cherian <george.cherian@ti.com> Signed-off-by:
-
zhangwei(Jovi) authored
commit 11034ae9 upstream Initialization of variable irq_flags and pc was missed when backport 11034ae9 to linux-3.0.y and linux-3.4.y, my fault. Signed-off-by:
zhangwei(Jovi) <jovi.zhangwei@huawei.com> Signed-off-by:
-
