VP2 and VP3 are unused video ports and VP3 share the same parent
clock as VP1 causing issue with pixel clock setting for HDMI (VP1).
The current DM firmware does not support changing parent clock if it
is shared by another component. It returns 0 for the determine_rate
query before causing set_rate to set the clock at default maximum of
1.8GHz which is a lot more than the maximum frequency videoports can
support (600MHz) causing SYNC LOST issues.
So remove the parent clocks for unused VPs to avoid conflict.

Fixes: 6f8605fd ("arm64: dts: ti: k3-am69-sk: Add DP and HDMI support")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Tested-by: Enric Balletbo i Serra <eballetbo@redhat.com>
Link: https://lore.kernel.org/r/20240201142308.4954-1-j-choudhary@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

HDMI audio can be enabled over AM62A-SK using the same DT overlay that
is used for AM625 / AM62-LP SK-EVMs.

Add the sk.dtb + hdmi-audio.dtbo combination for AM62A7-SK as well, to
check for overlay applicability during DTBS compile tests.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-4-a-bhatia1@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.

Add pinmux info for DSS DPI output.

Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the AM62A7-SK platforms.

Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-3-a-bhatia1@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add Display SubSystem (DSS) DT node for the AM62A7 SoC.

The DSS supports one each of video pipeline (vid) and video-lite
pipeline (vidl1). The video port 1 (vp1) is tied-off in AM62A SoC, but
the pipeline remains active. The video port 2 (vp2) outputs the DPI
signals. Both the video ports are connected to the pipelines via 2
identical overlay managers (ovr1 and ovr2).
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-2-a-bhatia1@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add the ADC node to the phyCORE AM64x and enable the ADC.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240201001439.3259450-1-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Fix the power domain device ID for wkup_vtm0 node.

Link: https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j784s4/devices.html
Fixes: 64821fbf ("arm64: dts: ti: j784s4: Add VTM node")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240201-b4-upstream-j721s2-fix-vtm-devid-v2-2-85fd568b77e3@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Fix the power domain device ID for wkup_vtm0 node.

Link: https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j721s2/devices.html
Fixes: d148e3fe ("arm64: dts: ti: j721s2: Add VTM node")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240201-b4-upstream-j721s2-fix-vtm-devid-v2-1-85fd568b77e3@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Enable the CPSW MDIO node, and link the pinctrl information to enable
ethernet on SK-AM62P.

Ethernet was unintentally broken on this board, even though these nodes
were already present, as enabling them was missed in the original
patch.

Fixes: c00504ea ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240201-am62p_cpsw_mdio-v1-1-05f758300f6e@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

CAN instances 0 and 1 in the mcu domain are brought on the common
processor board through headers J30 and J31 respectively. Thus, add
their respective transceivers 1 and 2 dt nodes to add support for
these CAN instances.

CAN instance 3 in the main domain is brought on the common
processor board through header J27. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceiver 3 on
the common processor board. Therefore, add transceiver dt nodes to add
support for this CAN instance.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240130102044.120483-4-b-kapoor@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

CAN instance 0 in the main domain is brought on the J7200 SoM through
header J1. Thus, Add transceiver dt node to add support for this CAN
instance.

Also, add the mux dt nodes to route CAN High and Low lines coming
from the SoC to the Common Processor Board.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240130102044.120483-3-b-kapoor@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add support for 18 CAN controllers in main domain and 2 CAN controllers
present in mcu domain. All the CAN controllers support classic CAN
messages as well as CAN_FD messages.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240130102044.120483-2-b-kapoor@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add TPM device to Mallow device tree file, the device is connected to
the SoC with SPI1/CS1, the same SPI interface is also available on an
extension header together with an additional CS0 signal.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240126165136.28543-1-francesco@dolcini.itSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

This node is an example node for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.

Examples should go in the bindings or other documentation.

Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-4-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

These nodes are example nodes for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.

Examples should go in the bindings or other documentation.

Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-3-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

This node is an example node for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.

Examples should go in the bindings or other documentation.

Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-2-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

PCIe node defined in the top-level J7200 SoC dtsi file is incomplete
and will not be functional unless it is extended with a SerDes PHY.

As the PHY and mode is only known at the board integration level, this
node should only be enabled when provided with this information.

Disable the PCIe node in the dtsi files and only enable when it is
actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-1-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-11-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-10-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-9-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-8-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-7-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-6-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-5-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-4-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-3-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-2-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-1-afd@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The phyBOARD-Electra populates a TPM module on SPI0 bus.
Add support for the Infineon SLB9670 TPM module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240123102921.1348777-1-w.egorov@phytec.deSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The clock on the ethernet1 PHY is turned on by default. This turns
the clock off as we do not use it.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240119225257.403222-1-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

memory node are required for bootloader operation on TI K3 J784S4 EVM
and AM69-SK boards for finding the memory size during early boot stage.

So, align Linux device tree by adding phase tag marking 'bootph-all',
which is to enable for all bootloader stages.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20240119171619.3759205-1-a-nandan@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The beagleplay dts was using a bit-bang gpio mdio bus as a work-around
for errata i2329. However since commit d04807b8 ("net: ethernet: ti:
davinci_mdio: Add workaround for errata i2329") the mdio driver itself
already takes care of this errata for effected silicon, which landed
well before the beagleplay dts. So i suspect the reason for the
workaround in upstream was simply due to copying the vendor dts.

Switch the dts to the ti,cpsw-mdio instead so it described the actual
hardware and is consistent with other AM625 based boards
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240112124505.2054212-1-sjoerd@collabora.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The USB0 port on the beagleplay can be used for DFU booting. To enable
that functionality mark with bootph-all.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Link: https://lore.kernel.org/r/20240112091745.1896922-3-sjoerd@collabora.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The USB0 port on the AM62x SK can be used for DFU booting. To enable
that functionality mark with bootph-all.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Link: https://lore.kernel.org/r/20240112091745.1896922-2-sjoerd@collabora.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB

Add line breaks - inode_to_text() is now much easier to read.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>