Instead of setting irq_set_irq_wake() directly in probe(), mark the device
as wakeup-capable, and use enable_irq_wake() and disable_irq_wake() in
suspend/resume path.

This also allows changing the wakeup setting dynamically at runtime using
/sys/devices/.../tsc2005/power/wakeup.
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20240711172719.1248373-4-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When the driver has been converted to use gpiod API it was requesting
and asserting the reset on probe, but never deasserted it. However
because of incorrect annotations in device tree marking reset line as
active high whereas in reality it is active low, the end result was
that the chip was never reset on probe. With polarity of the reset line
now corrected this became a problem.

Fix this by calling tsc200x_reset() from tsc200x_probe() to properly
complete the reset sequence and move requesting the reset GPIO and VIO
supply closer to the point where we need to start talking to the
hardware.

Fixes: d257f298 ("Input: tsc2005 - convert to gpiod")
Link: https://lore.kernel.org/r/20240711172719.1248373-3-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of hard-coding interrupt trigger rely on ACPI/DT/board code
to set it up appropriately.

Link: https://lore.kernel.org/r/20240711172719.1248373-2-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The chip needs to be powered up before calling tsc200x_stop_scan() which
communicates with it; move the call to enable the regulator earlier in
tsc200x_probe().

At the same time switch to using devm_regulator_get_enable() to simplify
error handling. This also makes sure that regulator is not shut off too
early when unbinding the driver.

Link: https://lore.kernel.org/r/20240711172719.1248373-1-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use of_property_present() to test for property presence rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240731191312.1710417-14-robh@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_clk_get_prepared() in order to remove a clk_unprepare() in an
error handling path of the probe and from the .remove() function.

This done, the whole .remove() function can also be axed because
'input_dev' is a managed resource allocated with
devm_input_allocate_device() and we can fully rely on devm for cleaning up.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/062986b0a5105cbc61330da0e55b22c00e2c1c4f.1722062145.git.christophe.jaillet@wanadoo.frSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch introduces a driver for the PixArt PS/2 touchpad, which
supports both clickpad and touchpad types.

At the same time, we extended the single data packet length to 16,
because according to the current PixArt hardware and FW design, we need
11 bytes/15 bytes to represent the complete three-finger/four-finger data.
Co-developed-by: Jon Xie <jon_xie@pixart.com>
Signed-off-by: Jon Xie <jon_xie@pixart.com>
Co-developed-by: Jay Lee <jay_lee@pixart.com>
Signed-off-by: Jay Lee <jay_lee@pixart.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/20240704125243.3633569-1-zhoubinbin@loongson.cnSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Zinitix touch controllers can use some of the sense lines for virtual
keys (like those found on many phones). Add support for those keys.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20240717-zinitix-tkey-v5-2-52ea4cd4bd50@trvn.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In some configurations the touch controller can support the touch-keys.
Document the linux,keycodes property that enables those keys and
specifies the keycodes that should be used to report the key events.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20240717-zinitix-tkey-v5-1-52ea4cd4bd50@trvn.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Export a sysfs interface that would allow reading and writing touchscreen
IC registers. With this interface many things can be done in usersapce
such as firmware updates. An example tool that utilizes this interface
for performing firmware updates can be found at [1].

[1] https://github.com/goodix/fwupdate_for_berlin_linuxSigned-off-by: Charles Wang <charles.goodix@gmail.com>
Link: https://lore.kernel.org/r/20240514115135.21410-1-charles.goodix@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Report input event directly on wakeup to ensure no press event is missed
when resuming from suspend.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240716000721.3485597-1-Frank.Li@nxp.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Remove reference to no longer working usbb2k-api-dev@nongnu.org
mailing list.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

MCS-5000/5080 chips belong to the 1st generation of Melfas chips,
manufactured in 2000-2007.

The driver relies on custom platform data (no DT support) and there
never were any users of this driver in the mainline kernel. It is likely
that the driver was (like mcs5000_ts driver) was tested on S3C6410 NCP
board (with Samsung S3C6410 SoC), but the touchkey device was never
added to the board file. This board was removed in v6.3 in commit
743c8fbb ("ARM: s3c: remove most s3c64xx board support").

Remove the driver since there are no users.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240714060029.1528662-2-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

MCS-5000 belongs to the 1st generation of Melfas chips, manufactured in
2000-2007.

The driver relies on custom platform data (no DT support) and there
never were any users of this driver in the mainline kernel. The commit
adding the driver mentioned that the driver was tested on S3C6410 NCP
board (with Samsung S3C6410 SoC) but the touchscreen device was never
added to the board file. This board was removed in v6.3 in commit
743c8fbb ("ARM: s3c: remove most s3c64xx board support").

Remove the driver since there are no users.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240714060029.1528662-1-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use __free(kfree) cleanup facility when allocating temporary buffers
for USB transfers.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240712051851.3463657-8-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This makes the code more compact and error handling more robust.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240712051851.3463657-7-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of using a single table containing information about various
touchscreens and enums to match the driver ID table data with chip
information define individual per-protocol instances of
usbtouch_device_info structure and reference them directly from
the usbtouch_devices ID table. This is simpler, safer, and uses less
memory in case some protocols are disabled.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240712051851.3463657-6-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The data in this table is shared between all instances of the
touchscreens so it should not be modified.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240712051851.3463657-5-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In preparation of splitting big usbtouch_dev_info table into separate
per-protocol structures and constifying them move process_pkt() from the
device info into main drvice structure and set it up in probe().
We can derive if we should use single- or multi-packet handling based
on presence of get_pkt_len() method.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240712051851.3463657-4-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Move the driver's ID table closer to where it is used in preparation
to it using pointers to device info/parameters instead of device type
enum.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240712051851.3463657-3-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There already exists perfectly suitable USB_DEVICE_INTERFACE_CLASS
macro, use it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240712051851.3463657-2-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of manually creating driver-specific device attributes
set struct usb_driver->dev_groups pointer to have the driver core
do it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240712051851.3463657-1-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch to the _scoped() version introduced in commit 365130fd
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.

In this case the err_fwnode_put label was no longer necessary and the
error code is returned directly.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240412-input_device_for_each_child_node_scoped-v1-6-dbad1bc7ea84@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch to the _scoped() version introduced in commit 365130fd
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240412-input_device_for_each_child_node_scoped-v1-5-dbad1bc7ea84@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch to the _scoped() version introduced in commit 365130fd
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240412-input_device_for_each_child_node_scoped-v1-4-dbad1bc7ea84@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch to the _scoped() version introduced in commit 365130fd
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240412-input_device_for_each_child_node_scoped-v1-3-dbad1bc7ea84@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch to the _scoped() version introduced in commit 365130fd
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.

In this case the err label was no longer necessary and EINVAL is
returned directly.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240412-input_device_for_each_child_node_scoped-v1-2-dbad1bc7ea84@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch to the _scoped() version introduced in commit 365130fd
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240412-input_device_for_each_child_node_scoped-v1-1-dbad1bc7ea84@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync up with mainline to bring in device_for_each_child_node_scoped()
and other newer APIs.

Merge tag 'kbuild-fixes-v6.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Make scripts/ld-version.sh robust against the latest LLD

 - Fix warnings in rpm-pkg with device tree support

 - Fix warnings in fortify tests with KASAN

* tag 'kbuild-fixes-v6.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  fortify: fix warnings in fortify tests with KASAN
  kbuild: rpm-pkg: avoid the warnings with dtb's listed twice
  kbuild: Make ld-version.sh more robust against version string changes

When a software KASAN mode is enabled, the fortify tests emit warnings
on some architectures.

For example, for ARCH=arm, the combination of CONFIG_FORTIFY_SOURCE=y
and CONFIG_KASAN=y produces the following warnings:

    TEST    lib/test_fortify/read_overflow-memchr.log
  warning: unsafe memchr() usage lacked '__read_overflow' warning in lib/test_fortify/read_overflow-memchr.c
    TEST    lib/test_fortify/read_overflow-memchr_inv.log
  warning: unsafe memchr_inv() usage lacked '__read_overflow' symbol in lib/test_fortify/read_overflow-memchr_inv.c
    TEST    lib/test_fortify/read_overflow-memcmp.log
  warning: unsafe memcmp() usage lacked '__read_overflow' warning in lib/test_fortify/read_overflow-memcmp.c
    TEST    lib/test_fortify/read_overflow-memscan.log
  warning: unsafe memscan() usage lacked '__read_overflow' symbol in lib/test_fortify/read_overflow-memscan.c
    TEST    lib/test_fortify/read_overflow2-memcmp.log
  warning: unsafe memcmp() usage lacked '__read_overflow2' warning in lib/test_fortify/read_overflow2-memcmp.c
     [ more and more similar warnings... ]

Commit 9c2d1328 ("kbuild: provide reasonable defaults for tool
coverage") removed KASAN flags from non-kernel objects by default.
It was an intended behavior because lib/test_fortify/*.c are unit
tests that are not linked to the kernel.

As it turns out, some architectures require -fsanitize=kernel-(hw)address
to define __SANITIZE_ADDRESS__ for the fortify tests.

Without __SANITIZE_ADDRESS__ defined, arch/arm/include/asm/string.h
defines __NO_FORTIFY, thus excluding <linux/fortify-string.h>.

This issue does not occur on x86 thanks to commit 4ec4190b
("kasan, x86: don't rename memintrinsics in uninstrumented files"),
but there are still some architectures that define __NO_FORTIFY
in such a situation.

Set KASAN_SANITIZE=y explicitly to the fortify tests.

Fixes: 9c2d1328 ("kbuild: provide reasonable defaults for tool coverage")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Closes: https://lore.kernel.org/all/0e8dee26-41cc-41ae-9493-10cd1a8e3268@app.fastmail.com/Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

After 8d1001f7 (kbuild: rpm-pkg: fix build error with CONFIG_MODULES=n),
the following warning "warning: File listed twice: *.dtb" is appearing for
every dtb file that is included.
The reason is that the commented commit already adds the folder
/lib/modules/%{KERNELRELEASE} in kernel.list file so the folder
/lib/modules/%{KERNELRELEASE}/dtb is no longer necessary, just remove it.

Fixes: 8d1001f7 ("kbuild: rpm-pkg: fix build error with CONFIG_MODULES=n")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

After [1] in upstream LLVM, ld.lld's version output became slightly
different when the cmake configuration option LLVM_APPEND_VC_REV is
disabled.

Before:

  Debian LLD 19.0.0 (compatible with GNU linkers)

After:

  Debian LLD 19.0.0, compatible with GNU linkers

This results in ld-version.sh failing with

  scripts/ld-version.sh: 18: arithmetic expression: expecting EOF: "10000 * 19 + 100 * 0 + 0,"

because the trailing comma is included in the patch level part of the
expression. While [1] has been partially reverted in [2] to avoid this
breakage (as it impacts the configuration stage and it is present in all
LTS branches), it would be good to make ld-version.sh more robust
against such miniscule changes like this one.

Use POSIX shell parameter expansion [3] to remove the largest suffix
after just numbers and periods, replacing of the current removal of
everything after a hyphen. ld-version.sh continues to work for a number
of distributions (Arch Linux, Debian, and Fedora) and the kernel.org
toolchains and no longer errors on a version of ld.lld with [1].

Fixes: 02aff859 ("kbuild: check the minimum linker version in Kconfig")
Link: https://github.com/llvm/llvm-project/commit/0f9fbbb63cfcd2069441aa2ebef622c9716f8dbb [1]
Link: https://github.com/llvm/llvm-project/commit/649cdfc4b6781a350dfc87d9b2a4b5a4c3395909 [2]
Link: https://pubs.opengroup.org/onlinepubs/9699919799/utilities/V3_chap02.html [3]
Suggested-by: Fangrui Song <maskray@google.com>
Reviewed-by: Fangrui Song <maskray@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Pull scheduler fixes from Borislav Petkov:

 - Fix a performance regression when measuring the CPU time of a thread
   (clock_gettime(CLOCK_THREAD_CPUTIME_ID,...)) due to the addition of
   PSI IRQ time accounting in the hotpath

 - Fix a task_struct leak due to missing to decrement the refcount when
   the task is enqueued before the timer which is supposed to do that,
   expires

 - Revert an attempt to expedite detaching of movable tasks, as finding
   those could become very costly. Turns out the original issue wasn't
   even hit by anyone

* tag 'sched_urgent_for_v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Move psi_account_irqtime() out of update_rq_clock_task() hotpath
  sched/deadline: Fix task_struct reference leak
  Revert "sched/fair: Make sure to try to detach at least one movable task"

Pull x86 fix from Borislav Petkov:

 - Make sure TF is cleared before calling other functions (BHI
   mitigation in this case) in the SYSENTER compat handler, as
   otherwise it will warn about being in single-step mode

* tag 'x86_urgent_for_v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/bhi: Avoid warning in #DB handler due to BHI mitigation

Pull i2c fixes from Wolfram Sang:
 "Fixes for the I2C testunit, the Renesas R-Car driver and some
  MAINTAINERS corrections"

* tag 'i2c-for-6.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: testunit: avoid re-issued work after read message
  i2c: rcar: ensure Gen3+ reset does not disturb local targets
  i2c: mark HostNotify target address as used
  i2c: testunit: correct Kconfig description
  MAINTAINERS: VIRTIO I2C loses a maintainer, gains a reviewer
  MAINTAINERS: delete entries for Thor Thayer
  i2c: rcar: clear NO_RXDMA flag after resetting
  i2c: rcar: bring hardware to known state when probing

Pull smb client fix from Steve French:
 "Small fix, also for stable"

* tag '6.10-rc7-smb3-client-fix' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix setting SecurityFlags to true

If you try to set /proc/fs/cifs/SecurityFlags to 1 it
will set them to CIFSSEC_MUST_NTLMV2 which no longer is
relevant (the less secure ones like lanman have been removed
from cifs.ko) and is also missing some flags (like for
signing and encryption) and can even cause mount to fail,
so change this to set it to Kerberos in this case.

Also change the description of the SecurityFlags to remove mention
of flags which are no longer supported.

Cc: stable@vger.kernel.org
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

Merge tag 'i2c-host-fixes-6.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current

This tag includes three fixes for the Renesas R-Car driver:

 1. Ensures the device is in a known state after probing.
 2. Allows clearing the NO_RXDMA flag after a reset.
 3. Forces a reset before any transfer on Gen3+ platforms to
    prevent disruption of the configuration during parallel
    transfers.