- 15 Feb, 2022 1 commit
-
-
Tobias Waldekranz authored
These chips have 8 built-in FE PHYs and 3 SERDES interfaces that can run at 1G. With the blamed commit, the built-in PHYs could no longer be connected to, using an MII PHY interface mode. Create a separate .phylink_get_caps callback for these chips, which takes the FE/GE split into consideration. Fixes: 2ee84cfe ("net: dsa: mv88e6xxx: convert to phylink_generic_validate()") Signed-off-by:
Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20220213185154.3262207-1-tobias@waldekranz.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
- 14 Feb, 2022 27 commits
-
-
Colin Ian King authored
There is a spelling mistake in an error message. Fix it. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Volodymyr Mytnyk authored
Add support of rule offloading added to the non-zero index chain, which was previously forbidden. Also, goto action is offloaded allowing to jump for processing of desired chain. Note that only implicit chain 0 is bound to the device port(s) for processing. The rest of chains have to be jumped by actions. Signed-off-by:
Volodymyr Mytnyk <vmytnyk@marvell.com> Signed-off-by:
-
David S. Miller authored
M Chetan Kumar says: ==================== net: wwan: debugfs dev reference not dropped This patch series contains WWAN subsystem & IOSM Driver changes to drop dev reference obtained as part of wwan debugfs dir entry retrieval. PATCH1: A new debugfs interface is introduced in wwan subsystem so that wwan driver can drop the obtained dev reference post debugfs use. PATCH2: IOSM Driver uses new debugfs interface to drop dev reference. Please refer to commit messages for details. ==================== Signed-off-by: -
M Chetan Kumar authored
Post debugfs use call wwan_put_debugfs_dir()to drop debugfs dev reference. Signed-off-by:
M Chetan Kumar <m.chetan.kumar@linux.intel.com> Signed-off-by:
-
M Chetan Kumar authored
WWAN driver call's wwan_get_debugfs_dir() to obtain WWAN debugfs dir entry. As part of this procedure it returns a reference to a found device. Since there is no debugfs interface available at WWAN subsystem, it is not possible to drop dev reference post debugfs use. This leads to side effects like post wwan driver load and reload the wwan instance gets increment from wwanX to wwanX+1. A new debugfs interface is added in wwan subsystem so that wwan driver can drop the obtained dev reference post debugfs use. void wwan_put_debugfs_dir(struct dentry *dir) Signed-off-by:
-
David S. Miller authored
Luiz Angelo Daros de Luca says: ==================== net: dsa: realtek: realtek-mdio: reset before setup This patch series cleans the realtek-smi reset code and copy that to the realtek-mdio. v1-v2) - do not run reset code block if GPIO is missing. It was printing "RESET deasserted" even when there is no GPIO configured. - reset switch after dsa_unregister_switch() - demote reset messages to debug v2-v3) - do not assert the reset on gpiod_get. Do it explicitly aferwards. - split the commit into two (one for each module) ==================== Signed-off-by: -
Luiz Angelo Daros de Luca authored
Some devices, like the switch in Banana Pi BPI R64 only starts to answer after a HW reset. It is the same reset code from realtek-smi. Reported-by:
Frank Wunderlich <frank-w@public-files.de> Signed-off-by:
Luiz Angelo Daros de Luca <luizluca@gmail.com> Tested-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
Alvin Šipraga <alsi@bang-olufsen.dk> Acked-by:
Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by:
-
Luiz Angelo Daros de Luca authored
When reset GPIO was missing, the driver was still printing an info message and still trying to assert the reset. Although gpiod_set_value() will silently ignore calls with NULL gpio_desc, it is better to make it clear the driver might allow gpio_desc to be NULL. The initial value for the reset pin was changed to GPIOD_OUT_LOW, followed by a gpiod_set_value() asserting the reset. This way, it will be easier to spot if and where the reset really happens. A new "asserted RESET" message was added just after the reset is asserted, similar to the existing "deasserted RESET" message. Both messages were demoted to dbg. The code comment is not needed anymore. Signed-off-by:
-
Ido Schimmel authored
Whenever rt6_uncached_list_flush_dev() swaps rt->rt6_idev to the blackhole device, parts of IPv6 stack might still need to increment one SNMP counter. Root cause, patch from Ido, changelog from Eric :) This bug suggests that we need to audit rt->rt6_idev usages and make sure they are properly using RCU protection. Fixes: e5f80fcf ("ipv6: give an IPv6 dev to blackhole_netdev") Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Luiz Angelo Daros de Luca authored
The macro was missed while renaming realtek-smi.h to realtek.h. Fixes: f5f11907 (net: dsa: realtek: rename realtek_smi to) Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
-
David S. Miller authored
Sebastian Andrzej Siewior says: ==================== net: dev: PREEMPT_RT fixups. this series removes or replaces preempt_disable() and local_irq_save() sections which are problematic on PREEMPT_RT. Patch 2 makes netif_rx() work from any context after I found suggestions for it in an old thread. Should that work, then the context-specific variants could be removed. v2…v3: - #2 - Export __netif_rx() so it can be used by everyone. - Add a lockdep assert to check for interrupt context. - Update the kernel doc and mention that the skb is posted to backlog NAPI. - Use __netif_rx() also in drivers/net/*.c. - Added Toke''s review tag and kept Eric's desptite the changes made. v1…v2: - #1 and #2 - merge patch 1 und 2 from the series (as per Toke). - updated patch description and corrected the first commit number (as per Eric). - #2 - Provide netif_rx() as in v1 and additionally __netif_rx() without local_bh disable()+enable() for the loopback driver. __netif_rx() is not exported (loopback is built-in only) so it won't be used drivers. If this doesn't work then we can still export/ define a wrapper as Eric suggested. - Added a comment that netif_rx() considered legacy. - #3 - Moved ____napi_schedule() into rps_ipi_queued() and renamed it napi_schedule_rps(). https://lore.kernel.org/all/20220204201259.1095226-1-bigeasy@linutronix.de/ v1: https://lore.kernel.org/all/20220202122848.647635-1-bigeasy@linutronix.de ==================== Signed-off-by: -
Sebastian Andrzej Siewior authored
Disabling interrupts and in the RPS case locking input_pkt_queue is split into local_irq_disable() and optional spin_lock(). This breaks on PREEMPT_RT because the spinlock_t typed lock can not be acquired with disabled interrupts. The sections in which the lock is acquired is usually short in a sense that it is not causing long und unbounded latiencies. One exception is the skb_flow_limit() invocation which may invoke a BPF program (and may require sleeping locks). By moving local_irq_disable() + spin_lock() into rps_lock(), we can keep interrupts disabled on !PREEMPT_RT and enabled on PREEMPT_RT kernels. Without RPS on a PREEMPT_RT kernel, the needed synchronisation happens as part of local_bh_disable() on the local CPU. ____napi_schedule() is only invoked if sd is from the local CPU. Replace it with __napi_schedule_irqoff() which already disables interrupts on PREEMPT_RT as needed. Move this call to rps_ipi_queued() and rename the function to napi_schedule_rps as suggested by Jakub. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by:
-
Sebastian Andrzej Siewior authored
Dave suggested a while ago (eleven years by now) "Let's make netif_rx() work in all contexts and get rid of netif_rx_ni()". Eric agreed and pointed out that modern devices should use netif_receive_skb() to avoid the overhead. In the meantime someone added another variant, netif_rx_any_context(), which behaves as suggested. netif_rx() must be invoked with disabled bottom halves to ensure that pending softirqs, which were raised within the function, are handled. netif_rx_ni() can be invoked only from process context (bottom halves must be enabled) because the function handles pending softirqs without checking if bottom halves were disabled or not. netif_rx_any_context() invokes on the former functions by checking in_interrupts(). netif_rx() could be taught to handle both cases (disabled and enabled bottom halves) by simply disabling bottom halves while invoking netif_rx_internal(). The local_bh_enable() invocation will then invoke pending softirqs only if the BH-disable counter drops to zero. Eric is concerned about the overhead of BH-disable+enable especially in regard to the loopback driver. As critical as this driver is, it will receive a shortcut to avoid the additional overhead which is not needed. Add a local_bh_disable() section in netif_rx() to ensure softirqs are handled if needed. Provide __netif_rx() which does not disable BH and has a lockdep assert to ensure that interrupts are disabled. Use this shortcut in the loopback driver and in drivers/net/*.c. Make netif_rx_ni() and netif_rx_any_context() invoke netif_rx() so they can be removed once they are no more users left. Link: https://lkml.kernel.org/r/20100415.020246.218622820.davem@davemloft.netSigned-off-by:
Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by:
-
Sebastian Andrzej Siewior authored
The preempt_disable() () section was introduced in commit cece1945 ("net: disable preemption before call smp_processor_id()") and adds it in case this function is invoked from preemtible context and because get_cpu() later on as been added. The get_cpu() usage was added in commit b0e28f1e ("net: netif_rx() must disable preemption") because ip_dev_loopback_xmit() invoked netif_rx() with enabled preemption causing a warning in smp_processor_id(). The function netif_rx() should only be invoked from an interrupt context which implies disabled preemption. The commit e30b38c2 ("ip: Fix ip_dev_loopback_xmit()") was addressing this and replaced netif_rx() with in netif_rx_ni() in ip_dev_loopback_xmit(). Based on the discussion on the list, the former patch (b0e28f1e) should not have been applied only the latter (e30b38c2). Remove get_cpu() and preempt_disable() since the function is supposed to be invoked from context with stable per-CPU pointers. Bottom halves have to be disabled at this point because the function may raise softirqs which need to be processed. Link: https://lkml.kernel.org/r/20100415.013347.98375530.davem@davemloft.netSigned-off-by: -
Dave Ertman authored
The status of support for RDMA is currently being tracked with two separate status flags. This is unnecessary with the current state of the driver. Simplify status tracking down to a single flag. Rename the helper function to denote the RDMA specific status and universally use the helper function to test the status bit. Signed-off-by:
Dave Ertman <david.m.ertman@intel.com> Tested-by:
Leszek Kaliszczuk <leszek.kaliszczuk@intel.com> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by:
-
David S. Miller authored
Colin Foster says: ==================== use bulk reads for ocelot statistics Ocelot loops over memory regions to gather stats on different ports. These regions are mostly continuous, and are ordered. This patch set uses that information to break the stats reads into regions that can get read in bulk. The motiviation is for general cleanup, but also for SPI. Performing two back-to-back reads on a SPI bus require toggling the CS line, holding, re-toggling the CS line, sending 3 address bytes, sending N padding bytes, then actually performing the read. Bulk reads could reduce almost all of that overhead, but require that the reads are performed via regmap_bulk_read. Verified with eth0 hooked up to the CPU port: NIC statistics: Good Rx Frames: 905 Rx Octets: 78848 Good Tx Frames: 691 Tx Octets: 52516 Rx + Tx 65-127 Octet Frames: 1574 Rx + Tx 128-255 Octet Frames: 22 Net Octets: 131364 Rx DMA chan 0: head_enqueue: 1 Rx DMA chan 0: tail_enqueue: 1032 Rx DMA chan 0: busy_dequeue: 628 Rx DMA chan 0: good_dequeue: 905 Tx DMA chan 0: head_enqueue: 346 Tx DMA chan 0: tail_enqueue: 345 Tx DMA chan 0: misqueued: 345 Tx DMA chan 0: empty_dequeue: 346 Tx DMA chan 0: good_dequeue: 691 p00_rx_octets: 52516 p00_rx_unicast: 691 p00_rx_frames_65_to_127_octets: 691 p00_tx_octets: 78848 p00_tx_unicast: 905 p00_tx_frames_65_to_127_octets: 883 p00_tx_frames_128_255_octets: 22 p00_tx_green_prio_0: 905 And with swp2 connected to swp3 with STP enabled: NIC statistics: tx_packets: 379 tx_bytes: 19708 rx_packets: 1 rx_bytes: 46 rx_octets: 64 rx_multicast: 1 rx_frames_below_65_octets: 1 rx_classified_drops: 1 tx_octets: 44630 tx_multicast: 387 tx_broadcast: 290 tx_frames_below_65_octets: 379 tx_frames_65_to_127_octets: 294 tx_frames_128_255_octets: 4 tx_green_prio_0: 298 tx_green_prio_7: 379 NIC statistics: tx_packets: 1 tx_bytes: 52 rx_packets: 713 rx_bytes: 34148 rx_octets: 46982 rx_multicast: 407 rx_broadcast: 306 rx_frames_below_65_octets: 399 rx_frames_65_to_127_octets: 310 rx_frames_128_to_255_octets: 4 rx_classified_drops: 399 rx_green_prio_0: 314 tx_octets: 64 tx_multicast: 1 tx_frames_below_65_octets: 1 tx_green_prio_7: 1 v1 > v2: reword commit messages v2 > v3: correctly mark this for net-next when sending v3 > v4: calloc array instead of zalloc per review v4 > v5: Apply CR suggestions for whitespace Fix calloc / zalloc mixup Properly destroy workqueues Add third commit to split long macros v5 > v6: Fix functionality - v5 was improperly tested Add bugfix for ethtool mutex lock Remove unnecessary ethtool stats reads v6 > v7: Remove mutex bug patch that was applied via net Rename function based on CR Add missed error check ==================== Signed-off-by: -
Colin Foster authored
Create and utilize bulk regmap reads instead of single access for gathering stats. The background reading of statistics happens frequently, and over a few contiguous memory regions. High speed PCIe buses and MMIO access will probably see negligible performance increase. Lower speed buses like SPI and I2C could see significant performance increase, since the bus configuration and register access times account for a large percentage of data transfer time. Signed-off-by:
Colin Foster <colin.foster@in-advantage.com> Reviewed-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by:
-
Colin Foster authored
Regmap supports bulk register reads. Ocelot does not. This patch adds support for Ocelot to invoke bulk regmap reads. That will allow any driver that performs consecutive reads over memory regions to optimize that access. Signed-off-by:
-
Colin Foster authored
In the ocelot.h file, several read / write macros were split across multiple lines, while others weren't. Split all macros that exceed the 80 character column width and match the style of the rest of the file. Signed-off-by:
-
Colin Foster authored
The ocelot_update_stats function only needs to read from one port, yet it was updating the stats for all ports. Update to only read the stats that are necessary. Signed-off-by:
-
David Ahern authored
Add reasons to __udp6_lib_rcv for skb drops. The only twist is that the NO_SOCKET takes precedence over the CSUM or other counters for that path (motivation behind this patch - csum counter was misleading). Signed-off-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
David S. Miller authored
Joseph CHAMG says: ==================== ADD DM9051 ETHERNET DRIVER DM9051 is a spi interface chip, need cs/mosi/miso/clock with an interrupt gpio pin ==================== Signed-off-by: -
Joseph CHAMG authored
Add davicom dm9051 spi ethernet driver, The driver work for the device platform which has the spi master Signed-off-by:
Joseph CHAMG <josright123@gmail.com> Signed-off-by:
-
Joseph CHAMG authored
This is a new yaml base data file for configure davicom dm9051 with device tree Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Tony Lu authored
The previous patch introduces a lock-free version of smc_tx_work() to solve unnecessary lock contention, which is expected to be held lock. So this adds comment to remind people to keep an eye out for locks. Suggested-by:
Stefan Raspl <raspl@linux.ibm.com> Signed-off-by:
Tony Lu <tonylu@linux.alibaba.com> Signed-off-by:
-
Kalash Nainwal authored
Generate RTM_NEWROUTE netlink notification when the route preference changes on an existing kernel generated default route in response to RA messages. Currently netlink notifications are generated only when this route is added or deleted but not when the route preference changes, which can cause userspace routing application state to go out of sync with kernel. Signed-off-by:
Kalash Nainwal <kalash@arista.com> Reviewed-by:
-
Davide Caratti authored
in current Linux, MTU policing does not take into account that packets at the TC ingress have the L2 header pulled. Thus, the same TC police action (with the same value of tcfp_mtu) behaves differently for ingress/egress. In addition, the full GSO size is compared to tcfp_mtu: as a consequence, the policer drops GSO packets even when individual segments have the L2 + L3 + L4 + payload length below the configured valued of tcfp_mtu. Improve the accuracy of MTU policing as follows: - account for mac_len for non-GSO packets at TC ingress. - compare MTU threshold with the segmented size for GSO packets. Also, add a kselftest that verifies the correct behavior. Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Reviewed-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
- 13 Feb, 2022 10 commits
-
-
Kees Cook authored
With GCC 12, -Wstringop-overread was warning about an implicit cast from char[6] to char[8]. However, the extra 2 bytes are always thrown away, alignment doesn't matter, and the risk of hitting the edge of unallocated memory has been accepted, so this prototype can just be converted to a regular char *. Silences: net/core/dev.c: In function ‘bpf_prog_run_generic_xdp’: net/core/dev.c:4618:21: warning: ‘ether_addr_equal_64bits’ reading 8 bytes from a region of size 6 [-Wstringop-overread] 4618 | orig_host = ether_addr_equal_64bits(eth->h_dest, > skb->dev->dev_addr); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ net/core/dev.c:4618:21: note: referencing argument 1 of type ‘const u8[8]’ {aka ‘const unsigned char[8]’} net/core/dev.c:4618:21: note: referencing argument 2 of type ‘const u8[8]’ {aka ‘const unsigned char[8]’} In file included from net/core/dev.c:91: include/linux/etherdevice.h:375:20: note: in a call to function ‘ether_addr_equal_64bits’ 375 | static inline bool ether_addr_equal_64bits(const u8 addr1[6+2], | ^~~~~~~~~~~~~~~~~~~~~~~ Reported-by:Marc Kleine-Budde <mkl@pengutronix.de> Tested-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Horatiu Vultur authored
When CONFIG_IPV6 is not set, then the linking of the lan966x driver fails with the following error: drivers/net/ethernet/microchip/lan966x/lan966x_main.c:444: undefined reference to `ipv6_mc_check_mld' The fix consists in adding a check also for IS_ENABLED(CONFIG_IPV6) Fixes: 47aeea0d ("net: lan966x: Implement the callback SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED") Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
Horatiu Vultur authored
When CONFIG_PTP_1588_CLOCK is compiled as a module, then the linking of the lan966x fails because it can't find references to the following functions 'ptp_clock_index', 'ptp_clock_register' and 'ptp_clock_unregister' The fix consists in adding CONFIG_PTP_1588_CLOCK_OPTIONAL as a dependency for the driver. Fixes: d0964594 ("net: lan966x: Add support for ptp clocks") Reported-by:
-
David S. Miller authored
Raju Lakkaraju says: ==================== net: lan743x: PCI11010 / PCI11414 devices Enhancements This patch series adds support of the Ethernet function of the PCI11010 / PCI11414 devices to the LAN743x driver. The PCI1xxxx family of devices consists of a PCIe switch with a variety of embedded PCI endpoints on its downstream ports. The PCI11010 / PCI11414 devices include an Ethernet 10/100/1000/2500 function as one of those embedded endpoints. ==================== Signed-off-by: -
Raju Lakkaraju authored
Add support for Clause-45 MDIO PHY management Signed-off-by:
Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Signed-off-by:
-
Raju Lakkaraju authored
This change facilitates the selection between SGMII and (R)GIII interfaces Signed-off-by:
-
Raju Lakkaraju authored
Increase MSI / MSI-X vectors supported from 8 to 16 and Interrupt De-assertion timers from 8 to 10 Signed-off-by:
-
Raju Lakkaraju authored
Add support for 4 Tx queues Signed-off-by:
-
Raju Lakkaraju authored
PCI11010/PCI11414 devices are enhancement of Ethernet LAN743x chip family. Signed-off-by:
-
M Chetan Kumar authored
This patch enables Intel M.2 7360 WWAN card support on IOSM Driver. Control path implementation is a reuse whereas data path implementation it uses a different protocol called as MUX Aggregation. The major portion of this patch covers the MUX Aggregation protocol implementation used for IP traffic communication. For M.2 7360 WWAN card, driver exposes 2 wwan AT ports for control communication. The user space application or the modem manager to use wwan AT port for data path establishment. During probe, driver reads the mux protocol device capability register to know the mux protocol version supported by device. Base on which the right mux protocol is initialized for data path communication. An overview of an Aggregation Protocol 1> An IP packet is encapsulated with 16 octet padding header to form a Datagram & the start offset of the Datagram is indexed into Datagram Header (DH). 2> Multiple such Datagrams are composed & the start offset of each DH is indexed into Datagram Table Header (DTH). 3> The Datagram Table (DT) is IP session specific & table_length item in DTH holds the number of composed datagram pertaining to that particular IP session. 4> And finally the offset of first DTH is indexed into DBH (Datagram Block Header). So in TX/RX flow Datagram Block (Datagram Block Header + Payload)is exchanged between driver & device. Signed-off-by:
-
- 12 Feb, 2022 1 commit
-
-
Jakub Kicinski authored
This reverts commit 038fcdaf. Christophe points out div64_u64() and do_div() have different calling conventions. One updates the param, the other returns the result. Reported-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/all/056a7276-c6f0-cd7e-9e46-1d8507a0b6b1@wanadoo.fr/ Fixes: 038fcdaf ("net: ethernet: cavium: use div64_u64() instead of do_div()") Link: https://lore.kernel.org/r/20220211020544.3262694-1-kuba@kernel.orgSigned-off-by:
-
- 11 Feb, 2022 1 commit
-
-
Julia Lawall authored
Platform_driver probe functions aren't called with locks held and thus don't need GFP_ATOMIC. Use GFP_KERNEL instead. Problem found with Coccinelle. Signed-off-by:
Julia Lawall <Julia.Lawall@inria.fr> Link: https://lore.kernel.org/r/20220210204223.104181-1-Julia.Lawall@inria.frSigned-off-by:
-
