- 29 Nov, 2019 19 commits
-
-
Anilkumar Kolli authored
Fixes sending the pdev id(0,1,2 for mac0, mac1, mac2) to FW in wmi cmd pktlog enable/disable. Signed-off-by:
Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Anilkumar Kolli authored
Use pipe_id id instead of ret in for loop. Signed-off-by:
-
Anilkumar Kolli authored
Copy CE and htc service configs for all pipes. Signed-off-by:
-
Anilkumar Kolli authored
Add missing tracing subsystem define. Signed-off-by:
-
Wen Gong authored
sdio does not support wow, this patch is to enable it. When system enter sleep state, if wowlan is enabled, then sdio chip will keep power if platform support keep power, after resume, it will not need to re-load firmware again. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029. Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
-
Wen Gong authored
Change log level from warn to dbg level of mpdu status of sdio chip. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by:
-
Wen Gong authored
After the firmware crashes ath10k recovers via ieee80211_reconfig(), which eventually leads to firmware configuration and including the encryption keys. However, because there is no new auth/assoc and 4-way-handshake, and firmware set the authorize flag after 4-way-handshake, so the authorize flag in firmware is not set in firmware without 4-way-handshake. This will lead to a failure of data transmission after recovery done when using encrypted connections like WPA-PSK. Set authorize flag after installing keys to firmware will fix the issue. This was noticed by testing firmware crashing using simulate_fw_crash debugfs file. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by:
-
Wen Gong authored
For sdio chip, the max credit size in firmware is 1556, the 1556 include payload, ieee80211 header, htt header, htc header. So it need to set the max mtu to 1500 to forbidden TX packet which exceed 1500 form application. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1. Signed-off-by:
-
Wen Gong authored
On SDIO chips the firmware log does not impact performance. To make it easier to debug firmware problems keep it enabled on the firmware. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Make sure the number of WBM_IDLE_LINK ring descriptors is power of 2. This increases the number of descriptors to 32k from the current ~18k to fix the target assert because of the shortage in the descriptors in WBM_IDLE_LINK ring. Remove unnecessary power of 2 calculation in ath11k_dp_link_desc_setup() as it is not required after this change. Signed-off-by:
Vasanthakumar Thiagarajan <vthiagar@codeaurora.org> Signed-off-by:
-
Vikas Patel authored
TLV length was 0 for TLV tag 'WMI_TAG_ARRAY_STRUCT' causing Q6 to crash when trying to configure pktlog filter via debugfs. Signed-off-by:
Vikas Patel <vikpatel@codeaurora.org> Signed-off-by:
-
Sriram R authored
skb_panic is hit during msdu coalescing whenever enough tailroom is not allocated based on the remaining msdu length which is spread across in different rx buffers. Compute the extra length for resizing the skb based on the total msdu length and the msdu length of the first buffer. Signed-off-by:
Sriram R <srirrama@codeaurora.org> Signed-off-by:
-
Pradeep Kumar Chitrapu authored
remove unused counter to avoid taking locks inorder to optimize cpu load. Using Flamegraph, cpu usage of ath11k_dp_tx() observed to be decreased from 5.58% to 3.74% with iperf traffic running with 80MHz bandwidth ap mode. Signed-off-by:
Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by:
-
Karthikeyan Periyasamy authored
In conf_tx() mac operation callback, we are truncating the tx params cw_min and cw_max due to lower data type cast. so modified the data type of cwmin and cwmax to avoid the trucation issue. Signed-off-by:
Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by:
-
John Crispin authored
This patch drops ath11k_hal_rx_parse_dst_ring_desc(). This function was creating a huge amount of load, which lead to a signifcant latency delay when processing data in the RX path. Pegging the processing on a specific core and running perf --top we get the following output when running HE80 at a fixed bandwidth of 1gbit. with patch 19.19% [ath11k] [k] ath11k_dp_process_rx 5.02% [ath11k] [k] ath11k_dp_rx_tid_del_func 4.39% [kernel] [k] v7_dma_inv_range 4.15% [kernel] [k] __slab_alloc.constprop.1 4.03% [kernel] [k] dev_gro_receive 3.86% [kernel] [k] tcp_gro_receive 3.07% [ip_tables] [k] ipt_do_table 2.96% [kernel] [k] dma_cache_maint_page without patch 21.64% [ath11k] [k] ath11k_hal_rx_parse_dst_ring_desc 10.80% [ath11k] [k] ath11k_dp_process_rx 3.77% [kernel] [k] v7_dma_inv_range 3.48% [kernel] [k] dev_gro_receive 3.32% [ath11k] [k] ath11k_dp_rx_tid_del_func 3.17% [mac80211] [k] ieee80211_rx_napi 2.70% [kernel] [k] dma_cache_maint_page 2.65% [mac80211] [k] ieee80211_sta_ps_transition When removing the the bandwidth limit and rerunning the test we see an overall throughput improvement of 3-400mbit when running 4x4 HE80. Signed-off-by:Shashidhar Lakkavalli <slakkavalli@datto.com> Signed-off-by:
John Crispin <john@phrozen.org> Signed-off-by:
-
Anilkumar Kolli authored
It is observed that ath11k STA mode UL throughput is low. This is due to packets delivered to FW from TCL instead of TQM. TCL AST search fail causes packet delivered to FW, fix this by properly configuring the TCL address search type and ast_hash. STA UL throughput is improved 10times with 11AC AP. Signed-off-by:
-
Anilkumar Kolli authored
The current ath11k driver failed to parse wmi_tlv_svc_rdy_ext_parse if there is change in wmi_mac_phy_capabilities length with below error. ath11k c000000.wifi1: failed to extract mac caps, idx :0 ath11k c000000.wifi1: failed to parse tlv -22 This is needed to get firmware version WLAN.HK.2.0.0.1-00240-QCAHKSWPL_SILICONZ-1 working. Signed-off-by:
-
Karthikeyan Periyasamy authored
Handled the error case with proper resource cleanup and moved the handling into a separate function from ath11k_mac_sta_state. Signed-off-by:
-
Ganesh Sesetti authored
The Previous configuartion of htt stats sounding info and pdev cca stats are invalid due to that getting time out error. Changing htt stats sounding info value from 0xFF to 0x00 and htt pdev cca stats from 0x10 to 0x00 Signed-off-by:
Ganesh Sesetti <gseset@codeaurora.org> Signed-off-by:
-
- 27 Nov, 2019 9 commits
-
-
Govind Singh authored
During driver load below warn logs are printed in the console if firmware doesn't support some optional HTC services, ex:pktlog. It is likely some older fw version may not support PKTLOG HTC service as legacy fw uses HTC DATA service for pktlog. Move this log to debug level to remove un-necessary warn message on console. htc.c:803: ath10k_warn(ar, "unsupported HTC service id: %d\n", htc.c:881: ath10k_warn(ar, "unsupported HTC service id: %d\n", Signed-off-by:
Govind Singh <govinds@codeaurora.org> Signed-off-by:
-
John Crispin authored
Trigger the WMI call en/disabling OBSS PD when the bss config changes or we assoc to an AP that broadcasts the IE. Signed-off-by:
-
John Crispin authored
Add target wait time wmi calls to the driver. En/disable the support from when the bss_config changes. We ignore the cmd completion events. Signed-off-by:
-
John Crispin authored
Add basic HE support to the driver. The sband_iftype data is generated from the capabilities read from the FW. Signed-off-by:
-
Tamizh chelvam authored
Remove unexecuted code while handling amsdu packets. The same logic is done before calling ath11k_dp_rx_msdu_coalesce Signed-off-by:
Tamizh chelvam <tamizhr@codeaurora.org> Signed-off-by:
-
Tamizh chelvam authored
TX rate stats for the retried packets for a station comes through tx completion events. Assigning hw reported bandwidth information directly to station's txrate bandwidth will cause below warning. Fix this warning by converting the hw reported bandwidth to mac80211 base bandwidth. [ 134.758190] PC is at cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211] [ 134.765730] LR is at cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211] [ 134.875014] [<ffffffbffca8d708>] cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211] [ 134.877192] [<ffffffbffcaa9704>] nl80211_put_sta_rate+0x54/0xf24 [cfg80211] [ 134.884829] [<ffffffbffcaa9d48>] nl80211_put_sta_rate+0x698/0xf24 [cfg80211] [ 134.891687] [<ffffffbffcaaa490>] nl80211_put_sta_rate+0xde0/0xf24 [cfg80211] [ 134.898975] [<ffffffc0004de748>] genl_lock_dumpit+0x30/0x4c [ 134.905998] [<ffffffc0004dc264>] netlink_dump+0xf4/0x248 [ 134.911291] [<ffffffc0004dc910>] __netlink_dump_start+0xe0/0x174 [ 134.916850] [<ffffffc0004df114>] genl_family_rcv_msg+0x130/0x2c0 Signed-off-by:
-
John Crispin authored
We can regularly see the following message. - "ath11k c000000.wifi1: failed to find the peer with peer_id 4" This happens when the FW starts sending stats for the peer whilst the peer is not fully associated. Convert this info message to a debug one. Signed-off-by:
-
John Crispin authored
Everytime a new peer gets associated, we see the following message in the log - ath11k c000000.wifi1: Unknown eventid: 0x6017 Ignore this event for now. We probably need to handle the event properly when we add OMI support. Signed-off-by:
-
John Crispin authored
mac80211 expects the definition of what HE rate info is available inside a struct prepended to the skb. Signed-off-by:
-
- 25 Nov, 2019 12 commits
-
-
Kalle Valo authored
Add an entry for ath11k to the MAINTAINERS file. Signed-off-by:
-
Kalle Valo authored
ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k uses mac80211 and supports AP, Station and Mesh modes. Even though ath11k has some similar code as with ath10k (especially the WMI layer) it was concluded to be simpler to have a "clean start" for ath11k code base and not try to share the code with ath10k. This makes maintenance easier and avoids major changes in ath10k, which would have significantly increased the risk of regressions in existing setups. Even though the driver is very similar with ath10k but there are major differences as well. The datapath is completely different. ath11k supports multiple MACs, called "soc" in the firmware interface. And there's only one WMI interface to support. Currently ath11k supports only IEEE 802.11ac mode, but patches for 802.11ax are available and they will be submitted after ath11k is accepted to upstream. The firmware images are available from ath11k-firmware repository but they will be also submitted to linux-firmware: https://github.com/kvalo/ath11k-firmware This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1. The driver has had multiple authors who are listed in alphabetical order below. Signed-off-by:
Bhagavathi Perumal S <bperumal@codeaurora.org> Signed-off-by:
Govindaraj Saminathan <gsamin@codeaurora.org> Signed-off-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Maharaja Kennadyrajan <mkenna@codeaurora.org> Signed-off-by:
Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by:
Miles Hu <milehu@codeaurora.org> Signed-off-by:
Muna Sinada <msinada@codeaurora.org> Signed-off-by:
Rajkumar Manoharan <rmanohar@codeaurora.org> Signed-off-by:
Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by:
Sven Eckelmann <seckelmann@datto.com> Signed-off-by:
Venkateswara Naralasetty <vnaralas@codeaurora.org>
-
Kalle Valo authored
ath11k is a driver for Qualcomm IEEE 802.11ax devices. Add a bindings document for the driver, first documenting IPQ8074 which is the only device ath11k currently supports. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Colin Ian King authored
There is a check on the retry counter invalid_buf_id_retry that is always false because invalid_buf_id_retry is initialized to zero on each iteration of a while-loop. Fix this by initializing the retry counter before the while-loop starts. Addresses-Coverity: ("Logically dead code") Fixes: b4a967b7 ("wil6210: reset buff id in status message after completion") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
Maya Erez <merez@codeaurora.org> Signed-off-by:
-
Linus Lüssing authored
So far, frames were forwarded regardless of the FCS correctness leading to userspace applications listening on the monitor mode interface to receive potentially broken frames, even with the "fcsfail" flag unset. By default, with the "fcsfail" flag of a monitor mode interface unset, frames with FCS errors should be dropped. With this patch, the fcsfail flag is taken into account correctly. Tested-on: QCA4019 firmware-5-ct-full-community-12.bin-lede.011 Cc: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
Linus Lüssing <ll@simonwunderlich.de> Signed-off-by:
-
Wen Gong authored
iw command only show rssi without each chain's rssi on sdio iw wlan0 station dump Station a0:40:a0:93:3e:de (on wlan0) signal: -82 dBm signal avg: -82 dBm after this patch, it will show each chain's rssi on sdio Station a0:40:a0:93:3e:de (on wlan0) signal: -82 [-84, -88] dBm signal avg: -82 [-84, -87] dBm For QCA6174 PCIe, the ppdu have the correct rssi of each chain, it indicate rssi of rx data by ath10k_htt_rx_h_signal. For sdio chip, the rssi of each chain stored in rx management reported by firmware, the ath10k_wmi_tlv_op_pull_mgmt_rx_ev which used for tlv wmi will get the rssi of each chain and stored them in wmi_mgmt_rx_ev_arg, then indicate them to mac80211. For non-tlv wmi chip, it will not get the rssi of each chain and not indicate to mac80211, for non-tlv wmi chip, this patch will not have impact. For tlv wmi chip, if the rssi of chain in mgmt is valid, it will be indicate to mac80211, tested with QCA6174 PCIe/SDIO, the rssi of 2 chain in mgmt is valid. rssi of chains in mgmt of QCA6174 SDIO: 92096.652780: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[0]:70 92096.657324: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[1]:68 92096.662009: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[2]:128 92096.666647: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[3]:128 rssi of chains in mgmt of QCA6174 PCIe: [ 1581.049816] ath10k_pci 0000:02:00.0: mgmt rssi[0]:17 [ 1581.049818] ath10k_pci 0000:02:00.0: mgmt rssi[1]:22 [ 1581.049821] ath10k_pci 0000:02:00.0: mgmt rssi[2]:128 [ 1581.049823] ath10k_pci 0000:02:00.0: mgmt rssi[3]:128 after apply this patch, the iw's rssi of PCIe do not changed, result is same with before. iw wlan0 station dump of QCA6174 PCIe: Station 6c:e8:73:b8:92:dc (on wlan0) signal: -70 [-77, -72] dBm signal avg: -69 [-78, -72] dBm iw wlan-5000mhz station dump of QCA9984 PCIe connected with 2 client which has 2 chain: Station 70:48:0f:1f:1a:b2 (on wlan-5000mhz) signal: -47 [-55, -48, -87, -88] dBm signal avg: -42 [-50, -43, -83, -86] dBm Station ac:c1:ee:39:e3:83 (on wlan-5000mhz) signal: -43 [-46, -45, -79, -84] dBm signal avg: -43 [-46, -46, -82, -83] dBm Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1. Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1. Tested with QCA9984 PCIe with firmware 10.4-3.9.0.2-00040. Signed-off-by: -
Jeffrey Hugo authored
When the BDF download QMI message has the end field set to 1, it signals the end of the transfer, and triggers the firmware to do a CRC check. The BDFs for msm8998 devices fail this check, yet the firmware is happy to still use the BDF. It appears that this error is not caught by the downstream drive by concidence, therefore there are production devices in the field where this issue needs to be handled otherwise we cannot support wifi on them. So, attempt to detect this scenario as best we can and treat it as non-fatal. Signed-off-by:
Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Jeffrey Hugo authored
When ath10k_qmi_init() fails, the error handling does not free the irq resources, which causes an issue if we EPROBE_DEFER as we'll attempt to (re-)register irqs which are already registered. Fix this by doing a power off since we just powered on the hardware, and freeing the irqs as error handling. Fixes: ba94c753 ("ath10k: add QMI message handshake for wcn3990 client") Signed-off-by:
-
Wen Gong authored
Add NL80211_FEATURE_ND_RANDOM_MAC_ADDR for NLO will enable the random mac address for netdetect case. iw command: iw phy0 wowlan enable net-detect net-detect randomize=AA:7B:A1:AC:B2:41/FF:FF:FF:FF:FF:FF interval 5000 delay 30 freqs 2412 matches ssid foo. After suspend, DUT will send probe request with mac AA:7B:A1:AC:B2:41. WCN3990, QCA9377, QCA6174 PCI also support this feature. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029. Signed-off-by:
-
Jeffrey Hugo authored
Firmware with the build id QC_IMAGE_VERSION_STRING=WLAN.HL.1.0.2-XXXX does not support the QMI_WLFW_HOST_CAP_REQ_V01 message and will return the QMI not supported error to the ath10k driver. Since not supporting this message is not fatal to the firmware nor the ath10k driver, lets catch this particular scenario and ignore it so that we can still bring up wifi services successfully. Signed-off-by:
-
Wen Gong authored
Download firmware time cost of SDIO is too long, it is about 480ms, add large size 2048 bytes for BMI download for SDIO chip, its time cost will reduced to 240ms. This will optimize the download firmware time cost. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1. Signed-off-by:
-
Wen Gong authored
the tlv len is set to the total len of the wmi cmd, it will trigger firmware crash, correct the tlv len. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174 PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1. Fixes: ce834e28 ("ath10k: support NET_DETECT WoWLAN feature") Signed-off-by:
-
