The GPI DMA mode requires for TX DMA to be prepared. Force SPI core to
provide TX buffer even if the caller didn't provide one by setting the
SPI_CONTROLLER_MUST_TX flag.

Fixes: b59c1224 ("spi: spi-geni-qcom: Add support for GPI dma")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230629095847.3648597-1-dmitry.baryshkov@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Commit a3eb9548 ("spi: dt-bindings: atmel,at91rm9200-spi: add sam9x7
compatible") adding sam9x7 compatible did not make any sense as it added
new compatible into middle of existing compatible list.  The intention
was probably to add new set of compatibles with sam9x7 as first one.

Fixes: a3eb9548 ("spi: dt-bindings: atmel,at91rm9200-spi: add sam9x7 compatible")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230624082054.37697-1-krzysztof.kozlowski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add sam9x7 compatible to DT bindings documentation.
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230623203056.689705-33-varshini.rajendran@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The RZ/V2M SoC comes with the Clocked Serial Interface (CSI)
IP, which is a master/slave SPI controller.

This commit adds a driver to support CSI master mode.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622113341.657842-4-fabrizio.castro.jz@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add dt-bindings for the CSI IP found inside the RZ/V2M SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622113341.657842-2-fabrizio.castro.jz@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Miquel Raynal <miquel.raynal@bootlin.com>:

I recently came across an issue with the Atmel spi controller driver
which would stop my transfers after a too small timeout when performing
big transfers (reading a 4MiB flash in one transfer). My initial idea
was to derive a the maximum amount of time a transfer would take
depending on its size and use that as value to avoid erroring-out when
not relevant. Mark wanted to go further by creating a core helper doing
that, based on the heuristics from the sun6i driver.

Here is a small series of 3 patches doing exactly that.

A helper was recently added to the core to factorize common code between
drivers, like the amount of time a driver should wait for a transfer to
happen.

It is of course possible to use a default value (like eg. 1s) but it is
way stronger to adapt this amount of time to the transfer. Indeed, long
transfers (eg. 4MiB) on a slow single-spi bus might take more than the
usual second of timeout and prevent lengthy transfers.

The core helper was heavily inspired by the logic applied in this
driver, the only difference being the minimum amount of time which was
enlarged from 0.1s to 0.5s.

Use this helper instead of open-coding it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jernej Škrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-4-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

A slow SPI bus clocks at ~20MHz, which means it would transfer about
2500 bytes per second with a single data line. Big transfers, like when
dealing with flashes can easily reach a few MiB. The current DMA timeout
is set to 1 second, which means any working transfer of about 4MiB will
always be cancelled.

With the above derivations, on a slow bus, we can assume every byte will
take at most 0.4ms. Said otherwise, we could add 4ms to the 1-second
timeout delay every 10kiB. On a 4MiB transfer, it would bring the
timeout delay up to 2.6s which still seems rather acceptable for a
timeout.

The consequence of this is that long transfers might be allowed, which
hence requires the need to interrupt the transfer if wanted by the
user. We can hence switch to the _interruptible variant of
wait_for_completion. This leads to a little bit more handling to also
handle the interrupted case but looks really acceptable overall.

While at it, we drop the useless, noisy and redundant WARN_ON() call.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ryan Wanner <ryan.wanner@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-3-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

STM32F4-F7 are, from hardware point of view, capable to handle device mode.
So this property should not be forced at false in dt-bindings.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/Message-Id: <20230621115523.923176-3-valentin.caron@foss.st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Big transfers might take a bit of time, too constraining timeouts might
lead to false positives. In order to simplify the drivers work and with
the goal of factorizing code in mind, let's add a helper that can be
used by any spi controller driver to derive a relevant per-transfer
timeout value.

The logic is simple: we know how much time it would take to transfer a
byte, we can easily derive the total theoretical amount of time involved
for each transfer. We multiply it by two to have a bit of margin and
enforce a minimum of 500ms.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-2-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now spi_geni_grab_gpi_chan() errors are correctly reported, the
-EPROBE_DEFER error should be returned from probe in case the
GPI dma driver is built as module and/or not probed yet.

Fixes: b59c1224 ("spi: spi-geni-qcom: Add support for GPI dma")
Fixes: 6532582c ("spi: spi-geni-qcom: fix error handling in spi_geni_grab_gpi_chan()")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230615-topic-sm8550-upstream-fix-spi-geni-qcom-probe-v2-1-670c3d9e8c9c@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

STM32F4 and STM32F7 can't switch to spi device mode.
Forbid this property with compatible "st,stm32f4-spi".
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230615075815.310261-4-valentin.caron@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for stm32h7 to use SPI controller in device role.
In such case, the spi instance should have the spi-slave property
defined.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230615075815.310261-5-valentin.caron@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Avoid usage of deprecated dmaengine_terminate_all and use
dmaengine_terminate_sync and dmaengine_terminate_async instead.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230615075815.310261-3-valentin.caron@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Preparing introduction of SPI device, rename the spi_master structure
into spi_controller. This doesn't have any functional impact since
spi_master was already a macro for spi_controller.
Referring now to ctrl instead of master since the spi_controller
structure might not be used as a master controller only.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230615075815.310261-2-valentin.caron@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Andi Shyti <andi.shyti@kernel.org>:

Two small cleanups in the probe function. The first puts in use
the managed spi master allocation while the second implements the
dev_err_probe() function.

Remove a misleading comment about the DMA operations of the Intel Mount
Evans SoC's SPI Controller as requested by Serge.
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com>
Link: https://lore.kernel.org/linux-spi/20230606191333.247ucbf7h3tlooxf@mobilestation/
Fixes: 0760d5d0 ("spi: dw: Add compatible for Intel Mount Evans SoC")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230606231844.726272-1-abe.kohandel@intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Document the DesignWare SSI controller compatible for Intel Mount Evans
Integrated Management Complex SoC.
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com>
Link: https://lore.kernel.org/r/20230606145402.474866-3-abe.kohandel@intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The Intel Mount Evans SoC's Integrated Management Complex uses the SPI
controller for access to a NOR SPI FLASH. However, the SoC doesn't
provide a mechanism to override the native chip select signal.

This driver doesn't use DMA for memory operations when a chip select
override is not provided due to the native chip select timing behavior.
As a result no DMA configuration is done for the controller and this
configuration is not tested.

The controller also has an errata where a full TX FIFO can result in
data corruption. The suggested workaround is to never completely fill
the FIFO. The TX FIFO has a size of 32 so the fifo_len is set to 31.
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230606145402.474866-2-abe.kohandel@intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simplify the code by using dev_err_probe() instead of dev_err()
and 'return'.
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230606012051.2139333-3-andi.shyti@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Use devm_spi_alloc_master() and get rid of one goto error path
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230606012051.2139333-2-andi.shyti@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

When the spi controller is registered and the cs_gpiods cannot be
assigned, causing a defer of the probe, there is an error print saying:
"probe - problem registering spi master"

This should not be announced as an error. Print this message for all
errors except for the probe defer.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20230602-pl022-defer-fix-v2-1-383f6bc2293a@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 87c61417 (spi: spi-imx: fix MX51_ECSPI_* macros when cs >
3) ensured that the argument passed to the macros was masked with &3,
so that we no longer write outside the intended fields in the various
control registers. When all chip selects are gpios, this works just
fine.

However, when a mix of native and gpio chip selects are in use, that
masking is too naive. Say, for example, that SS0 is muxed as native
chip select, and there is also a chip at 4 (obviously with a gpio
cs). In that case, when accessing the latter chip, both the SS0 pin
and the gpio pin will be asserted low.

The fix for this is to use the ->unused_native_cs value as channel
number for any spi device which uses a gpio as chip select.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230602115731.708883-1-linux@rasmusvillemoes.dkSigned-off-by: Mark Brown <broonie@kernel.org>

Replace the tuple devm_clk_get()/clk_prepare_enable() with the
single function devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230531205550.568340-1-andi.shyti@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Remove address/size-cells because they are already mentioned by common
spi-controller.yaml.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230601095908.563865-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Remove cs-gpios because it is already mentioned by common
spi-controller.yaml.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230601095908.563865-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Remove properties already mentioned by common spi-controller.yaml and
switch to unevaluatedProperties:false to achieve same functional effect.
This makes the binding a bit smaller.  Similarly there is no need to
allow additionalProperties for children, because spi-controller.yaml
already does it.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230601095908.563865-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Just drop a redundant empty line from the dw_spi_debugfs_init() function
left in the framework of the commit 0178f1e5 ("spi-dw-core.c: Fix
error checking for debugfs_create_dir") after removing the last return
statement.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20230530221725.26319-1-Sergey.Semin@baikalelectronics.ruSigned-off-by: Mark Brown <broonie@kernel.org>

Having no DMA is not an error. The simplest reason is not having it
configured. SPI will still be usable, so raise a warning instead to
get still some attention.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230531072850.739021-1-alexander.stein@ew.tq-group.comSigned-off-by: Mark Brown <broonie@kernel.org>

A warning added in commit b5762d95 ("spi: spi-qcom-qspi: Add DMA
mode support") was missing a newline. Add it.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Closes: https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/4573857/comment/44331d65_79128099/
Fixes: b5762d95 ("spi: spi-qcom-qspi: Add DMA mode support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230530111348.1.Ibd1f4827e18a26dc802cd6e5ac300d83dc1bc41c@changeidSigned-off-by: Mark Brown <broonie@kernel.org>

Make the pattern matching node names a bit stricter to improve DTS
consistency.  The pattern is restricted to:
1. Only one unit address or one -N suffix,
2. -N suffixes to decimal numbers.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230530144851.92059-6-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Get the fixes into CI for development.

Merge series from Boerge Struempfel <boerge.struempfel@gmail.com>:

Some spi controller switch the mosi line to high, whenever they are
idle. This may not be desired in all use cases. For example neopixel
leds can get confused and flicker due to misinterpreting the idle state.
Therefore, we introduce a new spi-mode bit, with which the idle behaviour
can be overwritten on a per device basis.

Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:

Hello,

compared to (implicit) v1 sent in March with Message-Id:
<20230309094704.2568531-1-u.kleine-koenig@pengutronix.de>, I reworked
patch 1 on feedback by AngeloGioacchino Del Regno. Patches 2 and 3 got
his Reviewed-by.

Best regards
Uwe

Uwe Kleine-König (3):
  spi: mt65xx: Properly handle failures in .remove()
  spi: mt65xx: Convert to platform remove callback returning void
  spi: mt65xx: Don't disguise a "return 0" as "return ret"

 drivers/spi/spi-mt65xx.c | 30 +++++++++++++++++-------------
 1 file changed, 17 insertions(+), 13 deletions(-)

base-commit: ac9a7868
--
2.39.2

Added the three missing spi mode bits SPI_3WIRE_HIZ, SPI_RX_CPHA_FLIP,
and SPI_MOSI_IDLE_LOW.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-6-boerge.struempfel@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

In order to increase usability, the command line options are sorted into
logical groups. In addition, the usage string was sorted alphabetically,
and the missing parameters '8','i' and 'o' were added. Furthermore, the
option descriptions were moved further to the right, in order to allow
for longer option names.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-5-boerge.struempfel@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Allow userspace to set SPI_MOSI_IDLE_LOW and the SPI_3WIRE_HIZ mode bit
using the SPI_IOC_WR_MODE32 ioctl.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-4-boerge.struempfel@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

By default, the spi-imx controller pulls the mosi line high, whenever it
is idle. This behaviour can be inverted per CS by setting the
corresponding DATA_CTL bit in the config register of the controller.

Also, since the controller mode-bits have to be touched anyways, the
SPI_CPOL and SPI_CPHA are replaced by the combined SPI_MODE_X_MASK flag.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-3-boerge.struempfel@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Some spi controller switch the mosi line to high, whenever they are
idle. This may not be desired in all use cases. For example neopixel
leds can get confused and flicker due to misinterpreting the idle state.
Therefore, we introduce a new spi-mode bit, with which the idle behaviour
can be overwritten on a per device basis.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-2-boerge.struempfel@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch fixes the error checking in spi-dw-core.c in
debugfs_create_dir. The DebugFS kernel API is developed in
a way that the caller can safely ignore the errors that
occur during the creation of DebugFS nodes.
Signed-off-by: Osama Muhammad <osmtendev@gmail.com>
Link: https://lore.kernel.org/r/20230520224025.14928-1-osmtendev@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>