Use netdev_alloc_skb rather than dev_alloc_skb
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic WQ desc supports a maximum 16K buf size, so split any send fragments
larger than 16K into several descs.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A0 revision ASIC has an erratum on the RQ desc cache on chip where the
cache can become corrupted causing pkt buf writes to wrong locations.  The s/w
workaround is to post a dummy RQ desc in the ring every 32 descs, causing a
flush of the cache.  A0 parts are not production, but there are enough of
these parts in the wild in test setups to warrant including workaround.  A1
revision ASIC parts fix erratum.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nic firmware can place resources (queues, intrs, etc) on multiple BARs, so
allow driver to discover/map resources beyond BAR0.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Its hard to tell if vlans are dropping frames, since
every frame given to vlan_???_start_xmit() functions
is accounted as fully transmitted by lower device.

We can test dev_queue_xmit() return values to
properly account for dropped frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

macvlan devices are currently not multi-queue capable.

We can do that defining rtnl_link_ops method,
get_tx_queues(), called from rtnl_create_link()

This new method gets num_tx_queues/real_num_tx_queues
from lower device.

macvlan_get_tx_queues() is a copy of vlan_get_tx_queues().

Because macvlan_start_xmit() has to update netdev_queue
stats only (and not dev->stats), I chose to change
tx_errors/tx_aborted_errors accounting to tx_dropped,
since netdev_queue structure doesnt define tx_errors /
tx_aborted_errors.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A few drivers still access the arguments to MDIO ioctls as an array of
u16.  Convert them to use struct mii_ioctl_data.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The standard MDIO ioctl numbers are well-established and these should
no longer be needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While perusing vendor driver, I saw that it did not enable the Vaux
power unless device was able to wake from lan for D3cold.
This might help for Rene's power issue.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a perpetual while() loop in unwinding partial
mapped tx skb on dma mapping failure.
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicate calls to netxen_napi_add().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alloc 12k skbuffs so that firmware can aggregate more
packets into one buffer. This doesn't raise memory
consumption since 9k skbs use 16k slab cache anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The FCoE DDP in 82599 can be used for both FCoE initiator as well as FCoE
target, depending on the indication of the exchange being the responder or
originator in the F_CTL (frame control) field in the encapsulated Fiber
Channel frame header (T10 Spec., FC-FS). For the initiator, OX_ID is used
for FCoE DDP, where for the target RX_ID is used for FCoE DDP.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds a simple selection of a FCoE tx queue based on the current cpu id to
distribute transmission of FCoE traffic evenly among multiple FCoE transmit
queues.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for multiple transmit queues to the Fiber Channel
over Ethernet (FCoE) feature found in 82599. Currently, FCoE has multiple
Rx queues available, along with a redirection table, that helps distribute
the I/O load across multiple CPUs based on the FC exchange ID. To make
this the most effective, we need to provide the same layout of transmit
queues to match receive.

Particularly, when Data Center Bridging (DCB) is enabled, the designated
traffic class for FCoE can have dedicated queues for just FCoE traffic,
while not affecting any other type of traffic flow.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates things so that vlan tags are taken into account when
setting the receive large packet maximum length.  This allows the VF driver
to correctly receive full sized frames when vlans are enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The igb_irq_disable/enable calls were causing virtual functions associated
with the igb physical function to have their interrupts disabled.  In order
to prevent this from occuring we should only clear/set the bits related to
the physical function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the set_rx_mode netdevice operation so that igb
can better support multiple unicast addresses.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove a debugging aid I accidently left in previous 'cleanup' patch
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan_dev_hard_start_xmit() & vlan_dev_hwaccel_hard_start_xmit()
select txqueue number 0, instead of using index provided by
skb_get_queue_mapping().

This is not correct after commit 2e59af3d
[vlan: multiqueue vlan device] because
txq->tx_packets  & txq->tx_bytes changes are performed on
a single location, and not the right locking.

Fix is to take the appropriate struct netdev_queue pointer
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pure style cleanup patch before surgery :)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm/br2684: netif_stop_queue() when atm device busy and netif_wake_queue() when we can send packets again.

This patch removes the call to dev_kfree_skb() when the atm device is busy.
Calling dev_kfree_skb() causes heavy packet loss then the device is under
heavy load, the more correct behavior should be to stop the upper layers,
then when the lower device can queue packets again wake the upper layers.
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>

fec_enet_mii, fec_enet_rx and fec_enet_tx are both only called by
fec_enet_interrupt in interrupt context.  So they must not use
spin_lock_irq/spin_unlock_irq.

This fixes:
	WARNING: at kernel/lockdep.c:2140 trace_hardirqs_on_caller+0x130/0x194()
	...
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mii_discover_phy is only called by fec_enet_mii (via mip->mii_func).  So
&fep->mii_lock is already held and mii_discover_phy must not call
mii_queue which locks &fep->mii_lock, too.

This was noticed by lockdep:

	=============================================
	[ INFO: possible recursive locking detected ]
	2.6.31-rc8-00038-g37d0892c #109
	---------------------------------------------
	swapper/1 is trying to acquire lock:
	 (&fep->mii_lock){-.....}, at: [<c01569f8>] mii_queue+0x2c/0xcc

	but task is already holding lock:
	 (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460

	other info that might help us debug this:
	2 locks held by swapper/1:
	 #0:  (rtnl_mutex){+.+.+.}, at: [<c0183534>] rtnl_lock+0x18/0x20
	 #1:  (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460

	stack backtrace:
	Backtrace:
	[<c00226fc>] (dump_backtrace+0x0/0x108) from [<c01eac14>] (dump_stack+0x18/0x1c)
	 r6:c781d118 r5:c03e41d8 r4:00000001
	[<c01eabfc>] (dump_stack+0x0/0x1c) from [<c005bae4>] (__lock_acquire+0x1a20/0x1a88)
	[<c005a0c4>] (__lock_acquire+0x0/0x1a88) from [<c005bbac>] (lock_acquire+0x60/0x74)
	[<c005bb4c>] (lock_acquire+0x0/0x74) from [<c01edda8>] (_spin_lock_irqsave+0x54/0x68)
	 r7:60000093 r6:c01569f8 r5:c785e468 r4:00000000
	[<c01edd54>] (_spin_lock_irqsave+0x0/0x68) from [<c01569f8>] (mii_queue+0x2c/0xcc)
	 r7:c785e468 r6:c0156b24 r5:600a0000 r4:c785e000
	[<c01569cc>] (mii_queue+0x0/0xcc) from [<c0156b78>] (mii_discover_phy+0x54/0xa8)
	 r8:00000002 r7:00000032 r6:c785e000 r5:c785e360 r4:c785e000
	[<c0156b24>] (mii_discover_phy+0x0/0xa8) from [<c0156354>] (fec_enet_interrupt+0xa4/0x460)
	 r5:c785e360 r4:c077a170
	[<c01562b0>] (fec_enet_interrupt+0x0/0x460) from [<c0066674>] (handle_IRQ_event+0x48/0x120)
	[<c006662c>] (handle_IRQ_event+0x0/0x120) from [<c0068438>] (handle_level_irq+0x94/0x11c)
	...
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bpq ether driver is modifying the data art of the skb by first
dropping the KISS byte (a command byte for the radio) then prepending the
length + 4 of the remaining AX.25 packet to be transmitted as a little
endian 16-bit number.  If the high byte of the length has a different
value than the dropped KISS byte users of clones of the skb may observe
this as corruption.  This was observed with by running listen(8) -a which
uses a packet socket which clones transmit packets.  The corruption will
then typically be displayed for as a KISS "TX Delay" command for AX.25
packets in the range of 252..508 bytes or any other KISS command for
yet larger packets.

Fixed by using skb_cow to create a private copy should the skb be cloned.
Using skb_cow also allows us to cleanup the old logic to ensure sufficient
headroom in the skb.

While at it, replace a return of 0 from bpq_xmit with the proper constant
NETDEV_TX_OK which is now being used everywhere else in this function.

Affected: all 2.2, 2.4 and 2.6 kernels.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Jann Traschewski <jann@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Request_irq() may fail in different ways, handle accordingly.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixed a lockdep warning which appeared when doing stress
memory tests over NFS:

	inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.

	page reclaim => nfs_writepage => tcp_sendmsg => lock sk_lock

	mount_root => nfs_root_data => tcp_close => lock sk_lock =>
			tcp_send_fin => alloc_skb_fclone => page reclaim

David raised a concern that if the allocation fails in tcp_send_fin(), and it's
GFP_ATOMIC, we are going to yield() (which sleeps) and loop endlessly waiting
for the allocation to succeed.

But fact is, the original GFP_KERNEL also sleeps. GFP_ATOMIC+yield() looks
weird, but it is no worse the implicit sleep inside GFP_KERNEL. Both could
loop endlessly under memory pressure.

CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: David S. Miller <davem@davemloft.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support to flash a firmware image to a device using ethtool.
The driver gets the filename of the firmware image and flashes the image
using the request firmware path.

The region "on the chip" to be flashed can be specified by an option.
It is upto the device driver to enumerate the region number passed by ethtool,
to the region to be flashed.

The default behavior is to flash all the regions on the chip.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Christoph Lameter pointed out that packet drops at qdisc level where not
accounted in SNMP counters. Only if application sets IP_RECVERR, drops
are reported to user (-ENOBUFS errors) and SNMP counters updated.

IP_RECVERR is used to enable extended reliable error message passing,
but these are not needed to update system wide SNMP stats.

This patch changes things a bit to allow SNMP counters to be updated,
regardless of IP_RECVERR being set or not on the socket.

Example after an UDP tx flood
# netstat -s 
...
IP:
    1487048 outgoing packets dropped
...
Udp:
...
    SndbufErrors: 1487048


send() syscalls, do however still return an OK status, to not
break applications.

Note : send() manual page explicitly says for -ENOBUFS error :

 "The output queue for a network interface was full.
  This generally indicates that the interface has stopped sending,
  but may be caused by transient congestion.
  (Normally, this does not occur in Linux. Packets are just silently
  dropped when a device queue overflows.) "

This is not true for IP_RECVERR enabled sockets : a send() syscall
that hit a qdisc drop returns an ENOBUFS error.

Many thanks to Christoph, David, and last but not least, Alexey !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan devices are currently not multi-queue capable.

We can do that with a new rtnl_link_ops method,
get_tx_queues(), called from rtnl_create_link()

This new method gets num_tx_queues/real_num_tx_queues
from real device.

register_vlan_device() is also handled.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was recently pointed out to me that the last_rx field of the
net_device structure wasn't updated regularly.  In fact only the
bonding driver really uses it currently.  Since the drop_monitor code
relies on the last_rx field to detect drops on recevie in hardware, We
need to find a more reliable way to rate limit our drop checks (so
that we don't check for drops on every frame recevied, which would be
inefficient.  This patch makes a last_rx timestamp that is private to
the drop monitor code and is updated for every device that we track.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The find_ie() function uses a size_t for the len parameter, and
directly uses len as a loop variable.  If any received packets
are malformed, it is possible for the decrease of len to overflow,
and since the result is unsigned, the loop will not terminate.
Change it to a signed int so the loop conditional works for
negative values.

This fixes the following soft lockup:

[38573.102007] BUG: soft lockup - CPU#0 stuck for 61s! [phy0:2230]
[38573.102007] Modules linked in: aes_i586 aes_generic fuse af_packet ipt_REJECT xt_tcpudp nf_conntrack_ipv4 nf_defrag_ipv4 xt_state iptable_filter ip_tables x_tables acpi_cpufreq binfmt_misc dm_mirror dm_region_hash dm_log dm_multipath dm_mod kvm_intel kvm uinput i915 arc4 ecb drm snd_hda_codec_idt ath5k snd_hda_intel hid_apple mac80211 usbhid appletouch snd_hda_codec snd_pcm ath cfg80211 snd_timer i2c_algo_bit ohci1394 video snd processor ieee1394 rfkill ehci_hcd sg sky2 backlight snd_page_alloc uhci_hcd joydev output ac thermal button battery sr_mod applesmc cdrom input_polldev evdev unix [last unloaded: scsi_wait_scan]
[38573.102007] irq event stamp: 2547724535
[38573.102007] hardirqs last  enabled at (2547724534): [<c1002ffc>] restore_all_notrace+0x0/0x18
[38573.102007] hardirqs last disabled at (2547724535): [<c10038f4>] apic_timer_interrupt+0x28/0x34
[38573.102007] softirqs last  enabled at (92950144): [<c103ab48>] __do_softirq+0x108/0x210
[38573.102007] softirqs last disabled at (92950274): [<c1348e74>] _spin_lock_bh+0x14/0x80
[38573.102007]
[38573.102007] Pid: 2230, comm: phy0 Tainted: G        W  (2.6.31-rc7-wl #8) MacBook1,1
[38573.102007] EIP: 0060:[<f8ea2d50>] EFLAGS: 00010292 CPU: 0
[38573.102007] EIP is at cmp_ies+0x30/0x180 [cfg80211]
[38573.102007] EAX: 00000082 EBX: 00000000 ECX: ffffffc1 EDX: d8efd014
[38573.102007] ESI: ffffff7c EDI: 0000004d EBP: eee2dc50 ESP: eee2dc3c
[38573.102007]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[38573.102007] CR0: 8005003b CR2: d8efd014 CR3: 01694000 CR4: 000026d0
[38573.102007] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[38573.102007] DR6: ffff0ff0 DR7: 00000400
[38573.102007] Call Trace:
[38573.102007]  [<f8ea2f8d>] cmp_bss+0xed/0x100 [cfg80211]
[38573.102007]  [<f8ea33e4>] cfg80211_bss_update+0x84/0x410 [cfg80211]
[38573.102007]  [<f8ea3884>] cfg80211_inform_bss_frame+0x114/0x180 [cfg80211]
[38573.102007]  [<f97255ff>] ieee80211_bss_info_update+0x4f/0x180 [mac80211]
[38573.102007]  [<f972b118>] ieee80211_rx_bss_info+0x88/0xf0 [mac80211]
[38573.102007]  [<f9739297>] ? ieee802_11_parse_elems+0x27/0x30 [mac80211]
[38573.102007]  [<f972b224>] ieee80211_rx_mgmt_probe_resp+0xa4/0x1c0 [mac80211]
[38573.102007]  [<f972bc59>] ieee80211_sta_rx_queued_mgmt+0x919/0xc50 [mac80211]
[38573.102007]  [<c1009707>] ? sched_clock+0x27/0xa0
[38573.102007]  [<c1009707>] ? sched_clock+0x27/0xa0
[38573.102007]  [<c105ffd0>] ? mark_held_locks+0x60/0x80
[38573.102007]  [<c1348be5>] ? _spin_unlock_irqrestore+0x55/0x70
[38573.102007]  [<c134baa5>] ? sub_preempt_count+0x85/0xc0
[38573.102007]  [<c1348bce>] ? _spin_unlock_irqrestore+0x3e/0x70
[38573.102007]  [<c12c1c0f>] ? skb_dequeue+0x4f/0x70
[38573.102007]  [<f972c021>] ieee80211_sta_work+0x91/0xb80 [mac80211]
[38573.102007]  [<c1009707>] ? sched_clock+0x27/0xa0
[38573.102007]  [<c134baa5>] ? sub_preempt_count+0x85/0xc0
[38573.102007]  [<c10479af>] worker_thread+0x18f/0x320
[38573.102007]  [<c104794e>] ? worker_thread+0x12e/0x320
[38573.102007]  [<c1348be5>] ? _spin_unlock_irqrestore+0x55/0x70
[38573.102007]  [<f972bf90>] ? ieee80211_sta_work+0x0/0xb80 [mac80211]
[38573.102007]  [<c104cbb0>] ? autoremove_wake_function+0x0/0x50
[38573.102007]  [<c1047820>] ? worker_thread+0x0/0x320
[38573.102007]  [<c104c854>] kthread+0x84/0x90
[38573.102007]  [<c104c7d0>] ? kthread+0x0/0x90
[38573.102007]  [<c1003ab7>] kernel_thread_helper+0x7/0x10

Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We can just display this upon enabling mac80211 with an
'if MAC80211 != n' check.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Refer to the wireless wiki for more information.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change it to a menuconfig to give it some documentation, to
refer users to our wireless wiki for extra resources and
documentation. It seems our wiki is still obscure to some.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All instances of file_operations should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>