iWARP requires OOO support which is already provided by the ll2
interface (until now was used only for iSCSI offload).
The changes mostly include opening a ll2 dedicated connection for
OOO and notifiying the FW about the handle id.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is the last of the initial iWARP patch series. It
adds the possiblity to actually detect iWARP from the device and enable
it in the critical locations which basically make iWARP available.

It wasn't submitted until now as iWARP hadn't been accepted into
the rdma tree.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Key length can't be negative.

Leave comparisons against nla_len() signed just in case truncated attribute
can sneak in there.

Space savings:

	add/remove: 0/0 grow/shrink: 0/7 up/down: 0/-7 (-7)
	function                                     old     new   delta
	pneigh_delete                                273     272      -1
	mlx5e_rep_netevent_event                    1415    1414      -1
	mlx5e_create_encap_header_ipv6              1194    1193      -1
	mlx5e_create_encap_header_ipv4              1071    1070      -1
	cxgb4_l2t_get                               1104    1103      -1
	__pneigh_lookup                               69      68      -1
	__neigh_create                              2452    2451      -1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Neigh entry size can't be negative.

Space savings:

	add/remove: 0/0 grow/shrink: 0/5 up/down: 0/-7 (-7)
	function                                     old     new   delta
	lowpan_neigh_construct                        25      24      -1
	clip_seq_sub_iter                            152     151      -1
	clip_ioctl                                  1475    1474      -1
	clip_constructor                              93      92      -1
	__neigh_create                              2455    2452      -3
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As measured in my prior patch ("sch_netem: faster rb tree removal"),
rbtree_postorder_for_each_entry_safe() is nice looking but much slower
than using rb_next() directly, except when tree is small enough
to fit in CPU caches (then the cost is the same)

Also note that there is not even an increase of text size :
$ size net/core/skbuff.o.before net/core/skbuff.o
   text	   data	    bss	    dec	    hex	filename
  40711	   1298	      0	  42009	   a419	net/core/skbuff.o.before
  40711	   1298	      0	  42009	   a419	net/core/skbuff.o

From: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While running TCP tests involving netem storing millions of packets,
I had the idea to speed up tfifo_reset() and did experiments.

I tried the rbtree_postorder_for_each_entry_safe() method that is
used in skb_rbtree_purge() but discovered it was slower than the
current tfifo_reset() method.

I measured time taken to release skbs with three occupation levels :
10^4, 10^5 and 10^6 skbs with three methods :

1) (current 'naive' method)

	while ((p = rb_first(&q->t_root))) {
		struct sk_buff *skb = netem_rb_to_skb(p);

		rb_erase(p, &q->t_root);
		rtnl_kfree_skbs(skb, skb);
	}

2) Use rb_next() instead of rb_first() in the loop :

	p = rb_first(&q->t_root);
	while (p) {
		struct sk_buff *skb = netem_rb_to_skb(p);

		p = rb_next(p);
		rb_erase(&skb->rbnode, &q->t_root);
		rtnl_kfree_skbs(skb, skb);
	}

3) "optimized" method using rbtree_postorder_for_each_entry_safe()

	struct sk_buff *skb, *next;

	rbtree_postorder_for_each_entry_safe(skb, next,
					     &q->t_root, rbnode) {
               rtnl_kfree_skbs(skb, skb);
	}
	q->t_root = RB_ROOT;

Results :

method_1:while (rb_first()) rb_erase() 10000 skbs in 690378 ns (69 ns per skb)
method_2:rb_first; while (p) { p = rb_next(p); ...}  10000 skbs in 541846 ns (54 ns per skb)
method_3:rbtree_postorder_for_each_entry_safe() 10000 skbs in 868307 ns (86 ns per skb)

method_1:while (rb_first()) rb_erase() 99996 skbs in 7804021 ns (78 ns per skb)
method_2:rb_first; while (p) { p = rb_next(p); ...}  100000 skbs in 5942456 ns (59 ns per skb)
method_3:rbtree_postorder_for_each_entry_safe() 100000 skbs in 11584940 ns (115 ns per skb)

method_1:while (rb_first()) rb_erase() 1000000 skbs in 108577838 ns (108 ns per skb)
method_2:rb_first; while (p) { p = rb_next(p); ...}  1000000 skbs in 82619635 ns (82 ns per skb)
method_3:rbtree_postorder_for_each_entry_safe() 1000000 skbs in 127328743 ns (127 ns per skb)

Method 2) is simply faster, probably because it maintains a smaller
working size set.

Note that this is the method we use in tcp_ofo_queue() already.

I will also change skb_rbtree_purge() in a second patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

it seems no need to keep tun_get() and __tun_get() at same time.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

reset the driver's DCB state in couple of places
where it was missing.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rick Farrington says:

====================
liquidio: firmware loading

1. Allow host driver parameter to override auto-loaded firmware (in flash).
2. Verify version of firmware that is auto-loaded from flash.
3. Change value of fw_type module parameter to reflect default firmware
   image name that is loaded by host driver (in /sys/module/liquidio/...)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: port enabling

This patchset makes slave open and close symmetrical and provides
helpers for enabling or disabling a given DSA port.

Changes in v3:
  - save the phy_device change for a future patchset

Changes in v2:
  - do not remove the phy argument from port enable/disable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide dsa_port_enable and dsa_port_disable helpers to respectively
enable and disable a switch port. This makes the dsa_port_set_state_now
helper static.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DSA slave open function configures the unicast MAC addresses on the
master device, enable the switch port, change its STP state, then start
the PHY device.

Make the close function symmetric, by first stopping the PHY device,
then changing the STP state, disabling the switch port and restore the
master device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

For older hosts without multi-channel (vRSS) support, and some error
cases, we still need to set the real number of queues to one.
This patch adds this missing setting.

Fixes: 8195b139 ("hv_netvsc: fix deadlock on hotplug")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petar Penkov says:

====================
net: Improve code coverage of syzkaller

This patch series is intended to improve code coverage of syzkaller on
the early receive path, specifically including flow dissector, GRO,
and GRO with frags parts of the networking stack. Syzkaller exercises
the stack through the TUN driver and this is therefore where changes
reside. Current coverage through netif_receive_skb() is limited as it
does not touch on any of the aforementioned code paths. Furthermore,
for full coverage, it is necessary to have more flexibility over the
linear and non-linear data of the skbs.

The following patches address this by providing the user(syzkaller)
with the ability to send via napi_gro_receive() and napi_gro_frags().
Additionally, syzkaller can specify how many fragments there are and
how much data per fragment there is. This is done by exploiting the
convenient structure of iovecs. Finally, this patch series adds
support for exercising the flow dissector during fuzzing.

The code path including napi_gro_receive() can be enabled via the
IFF_NAPI flag.  The remainder of the changes in this patch series give
the user significantly more control over packets entering the kernel.
To avoid potential security vulnerabilities, hide the ability to send
custom skbs and the flow dissector code paths behind a
capable(CAP_NET_ADMIN) check to require special user privileges.

Changes since v2 based on feedback from Willem de Bruijn and Mahesh
Bandewar:

Patch 1/ No changes.
Patch 2/ Check if the preconditions for IFF_NAPI_FRAGS (IFF_NAPI and
	 IFF_TAP) are met before opening/attaching rather than after.
	 If they are not, change the behavior from discarding the
	 flag to rejecting the command with EINVAL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a TUN/TAP receive mode that exercises the napi_gro_frags()
interface. This mode is available only in TAP mode, as the interface
expects packets with Ethernet headers.

Furthermore, packets follow the layout of the iovec_iter that was
received. The first iovec is the linear data, and every one after the
first is a fragment. If there are more fragments than the max number,
drop the packet. Additionally, invoke eth_get_headlen() to exercise flow
dissector code and to verify that the header resides in the linear data.

The napi_gro_frags() mode requires setting the IFF_NAPI_FRAGS option.
This is imposed because this mode is intended for testing via tools like
syzkaller and packetdrill, and the increased flexibility it provides can
introduce security vulnerabilities. This flag is accepted only if the
device is in TAP mode and has the IFF_NAPI flag set as well. This is
done because both of these are explicit requirements for correct
operation in this mode.
Signed-off-by: Petar Penkov <peterpenkov96@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: davem@davemloft.net
Cc: ppenkov@stanford.edu
Acked-by: Mahesh Bandewar <maheshb@google,com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes TUN driver to use napi_gro_receive() upon receiving packets
rather than netif_rx_ni(). Adds flag IFF_NAPI that enables these
changes and operation is not affected if the flag is disabled.  SKBs
are constructed upon packet arrival and are queued to be processed
later.

The new path was evaluated with a benchmark with the following setup:
Open two tap devices and a receiver thread that reads in a loop for
each device. Start one sender thread and pin all threads to different
CPUs. Send 1M minimum UDP packets to each device and measure sending
time for each of the sending methods:
	napi_gro_receive():	4.90s
	netif_rx_ni():		4.90s
	netif_receive_skb():	7.20s
Signed-off-by: Petar Penkov <peterpenkov96@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: davem@davemloft.net
Cc: ppenkov@stanford.edu
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These two drivers (dummy and ifb) call ether_setup(), after commit
61e84623 ("net: centralize net_device min/max MTU checking"), the
range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.

These two devices should not have limits on MTU. This patch set their
min_mtu/max_mtu to 0. So that dev_set_mtu() will not check the mtu range,
and can be set with any value.

CC: Eric Dumazet <edumazet@google.com>
CC: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't populate const array ver_list on the stack, instead make it
static. Makes the object code smaller by over 400 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  18444	   3168	    320	  21932	   55ac	drivers/net/hyperv/netvsc.o

After:
   text	   data	    bss	    dec	    hex	filename
  17950	   3224	    320	  21494	   53f6	drivers/net/hyperv/netvsc.o

(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before the delete operator was added, this datastructure maintained
an invariant that intermediate nodes were only present when necessary
to build the tree.  This patch updates the delete operation to reinstate
that invariant by removing unnecessary intermediate nodes after a node is
removed and thus keeping the tree structure at a minimal size.
Suggested-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use setup_timer function instead of initializing timer with the
   function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use setup_timer function instead of initializing timer with the
   function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use setup_timer function instead of initializing timer with the
   function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the xmit/rx fastpath, the function dma_map_single rarely fails.
Therefore, add an unlikely() optimization to this error check
conditional.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull parisc fixes from Helge Deller:

 - Unbreak parisc bootloader by avoiding a gcc-7 optimization to convert
   multiple byte-accesses into one word-access.

 - Add missing HWPOISON page fault handler code. I completely missed
   that when I added HWPOISON support during this merge window and it
   only showed up now with the madvise07 LTP test case.

 - Fix backtrace unwinding to stop when stack start has been reached.

 - Issue warning if initrd has been loaded into memory regions with
   broken RAM modules.

 - Fix HPMC handler (parisc hardware fault handler) to comply with
   architecture specification.

 - Avoid compiler warnings about too large frame sizes.

 - Minor init-section fixes.

* 'parisc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Unbreak bootloader due to gcc-7 optimizations
  parisc: Reintroduce option to gzip-compress the kernel
  parisc: Add HWPOISON page fault handler code
  parisc: Move init_per_cpu() into init section
  parisc: Check if initrd was loaded into broken RAM
  parisc: Add PDCE_CHECK instruction to HPMC handler
  parisc: Add wrapper for pdc_instr() firmware function
  parisc: Move start_parisc() into init section
  parisc: Stop unwinding at start of stack
  parisc: Fix too large frame size warnings

Pull rdma fixes from Doug Ledford:

 - Smattering of miscellanous fixes

 - A five patch series for i40iw that had a patch (5/5) that was larger
   than I would like, but I took it because it's needed for large scale
   users

 - An 8 patch series for bnxt_re that landed right as I was leaving on
   PTO and so had to wait until now...they are all appropriate fixes for
   -rc IMO

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (22 commits)
  bnxt_re: Don't issue cmd to delete GID for QP1 GID entry before the QP is destroyed
  bnxt_re: Fix memory leak in FRMR path
  bnxt_re: Remove RTNL lock dependency in bnxt_re_query_port
  bnxt_re: Fix race between the netdev register and unregister events
  bnxt_re: Free up devices in module_exit path
  bnxt_re: Fix compare and swap atomic operands
  bnxt_re: Stop issuing further cmds to FW once a cmd times out
  bnxt_re: Fix update of qplib_qp.mtu when modified
  i40iw: Add support for port reuse on active side connections
  i40iw: Add missing VLAN priority
  i40iw: Call i40iw_cm_disconn on modify QP to disconnect
  i40iw: Prevent multiple netdev event notifier registrations
  i40iw: Fail open if there are no available MSI-X vectors
  RDMA/vmw_pvrdma: Fix reporting correct opcodes for completion
  IB/bnxt_re: Fix frame stack compilation warning
  IB/mlx5: fix debugfs cleanup
  IB/ocrdma: fix incorrect fall-through on switch statement
  IB/ipoib: Suppress the retry related completion errors
  iw_cxgb4: remove the stid on listen create failure
  iw_cxgb4: drop listen destroy replies if no ep found
  ...

Pull networking fixes from David Miller:

 1) Fix NAPI poll list corruption in enic driver, from Christian
    Lamparter.

 2) Fix route use after free, from Eric Dumazet.

 3) Fix regression in reuseaddr handling, from Josef Bacik.

 4) Assert the size of control messages in compat handling since we copy
    it in from userspace twice. From Meng Xu.

 5) SMC layer bug fixes (missing RCU locking, bad refcounting, etc.)
    from Ursula Braun.

 6) Fix races in AF_PACKET fanout handling, from Willem de Bruijn.

 7) Don't use ARRAY_SIZE on spinlock array which might have zero
    entries, from Geert Uytterhoeven.

 8) Fix miscomputation of checksum in ipv6 udp code, from Subash Abhinov
    Kasiviswanathan.

 9) Push the ipv6 header properly in ipv6 GRE tunnel driver, from Xin
    Long.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
  inet: fix improper empty comparison
  net: use inet6_rcv_saddr to compare sockets
  net: set tb->fast_sk_family
  net: orphan frags on stand-alone ptype in dev_queue_xmit_nit
  MAINTAINERS: update git tree locations for ieee802154 subsystem
  net: prevent dst uses after free
  net: phy: Fix truncation of large IRQ numbers in phy_attached_print()
  net/smc: no close wait in case of process shut down
  net/smc: introduce a delay
  net/smc: terminate link group if out-of-sync is received
  net/smc: longer delay for client link group removal
  net/smc: adapt send request completion notification
  net/smc: adjust net_device refcount
  net/smc: take RCU read lock for routing cache lookup
  net/smc: add receive timeout check
  net/smc: add missing dev_put
  net: stmmac: Cocci spatch "of_table"
  lan78xx: Use default values loaded from EEPROM/OTP after reset
  lan78xx: Allow EEPROM write for less than MAX_EEPROM_SIZE
  lan78xx: Fix for eeprom read/write when device auto suspend
  ...

Merge tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor

Pull apparmor updates from John Johansen:
 "This is the apparmor pull request, similar to SELinux and seccomp.

  It's the same series that I was sent to James' security tree + one
  regression fix that was found after the series was sent to James and
  would have been sent for v4.14-rc2.

  Features:
  - in preparation for secid mapping add support for absolute root view
    based labels
  - add base infastructure for socket mediation
  - add mount mediation
  - add signal mediation

  minor cleanups and changes:
  - be defensive, ensure unconfined profiles have dfas initialized
  - add more debug asserts to apparmorfs
  - enable policy unpacking to audit different reasons for failure
  - cleanup conditional check for label in label_print
  - Redundant condition: prev_ns. in [label.c:1498]

  Bug Fixes:
  - fix regression in apparmorfs DAC access permissions
  - fix build failure on sparc caused by undeclared signals
  - fix sparse report of incorrect type assignment when freeing label proxies
  - fix race condition in null profile creation
  - Fix an error code in aafs_create()
  - Fix logical error in verify_header()
  - Fix shadowed local variable in unpack_trans_table()"

* tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
  apparmor: fix apparmorfs DAC access permissions
  apparmor: fix build failure on sparc caused by undeclared signals
  apparmor: fix incorrect type assignment when freeing proxies
  apparmor: ensure unconfined profiles have dfas initialized
  apparmor: fix race condition in null profile creation
  apparmor: move new_null_profile to after profile lookup fns()
  apparmor: add base infastructure for socket mediation
  apparmor: add more debug asserts to apparmorfs
  apparmor: make policy_unpack able to audit different info messages
  apparmor: add support for absolute root view based labels
  apparmor: cleanup conditional check for label in label_print
  apparmor: add mount mediation
  apparmor: add the ability to mediate signals
  apparmor: Redundant condition: prev_ns. in [label.c:1498]
  apparmor: Fix an error code in aafs_create()
  apparmor: Fix logical error in verify_header()
  apparmor: Fix shadowed local variable in unpack_trans_table()

Merge branch 'ieee802154-for-davem-2017-09-20' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next

Stefan Schmidt says:

====================
pull-request: ieee802154 2017-09-20

Here comes a pull request for ieee802154 changes I have queued up for
this merge window.

Normally these have been coming through the bluetooth tree but as this
three have been falling through the cracks so far and I have to review
and ack all of them anyway I think it makes sense if I save the
bluetooth people some work and handle them directly.

Its the first pull request I send to you so please let me know if I did
something wrong or if you prefer a different format.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>