* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
  Revert "drm/i915: enable rc6 by default"
  drm/i915: Clean up i915_driver_load failure path
  drm/i915: Enable GPU reset on Ivybridge.
  drm/i915/dp: manage sink power state if possible
  drm/i915/dp: consolidate AUX retry code
  drm/i915/dp: remove DPMS mode tracking from DP
  drm/i915/dp: try to read receiver capabilities 3 times when detecting
  drm/i915/dp: read more receiver capability bits on hotplug
  drm/i915/dp: use DP DPCD defines when looking at DPCD values
  drm/i915/dp: retry link status read 3 times on failure

...which is measured by the size and not the amount of space remaining.

Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:

[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>

This reverts commit a51f7a66.

We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: Keith Packard <keithp@keithp.com>

i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.

i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.

i915_driver_load also has some incorrect gotos in the error cleanup
paths:

 * After failing to initialize the GTT (which cannot happen, btw,
   intel_gtt_get returns a fixed (non-NULL) value), it tries to
   free the uninitialized WC IO mapping. Fixed this by changing the
   target from out_iomapfree to out_rmmap
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Lin Ming <ming.m.lin@intel.com>

That file harkens back to the days of the big 2.4 -> 2.6 version jump,
and was based even then on older versions.  Some of it is just obsolete,
and Jesper Juhl points out that it talks about kernel versions 2.6 and
should be updated to 3.0.

Remove some obsolete text, and re-phrase some other to not be 2.6-specific.
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] msp3400: fill in v4l2_tuner based on vt->type field
  [media] tuner-core.c: don't change type field in g_tuner or g_frequency
  [media] cx18/ivtv: fix g_tuner support
  [media] tuner-core: power up tuner when called with s_power(1)
  [media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
  [media] tuner-core: simplify the standard fixup
  [media] tuner-core/v4l2-subdev: document that the type field has to be filled in
  [media] v4l2-subdev.h: remove unused s_mode tuner op
  [media] feature-removal-schedule: change in how radio device nodes are handled
  [media] bttv: fix s_tuner for radio
  [media] pvrusb2: fix g/s_tuner support
  [media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
  [media] tuner-core: fix tuner_resume: use t->mode instead of t->type
  [media] tuner-core: fix s_std and s_tuner

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: Reintroduce dropped call to check_wakeup_irqs

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: drop spinlock before calling cifs_put_tlink
  cifs: fix expand_dfs_referral
  cifs: move bdi_setup_and_register outside of CONFIG_CIFS_DFS_UPCALL
  cifs: factor smb_vol allocation out of cifs_setup_volume_info
  cifs: have cifs_cleanup_volume_info not take a double pointer
  cifs: fix build_unc_path_to_root to account for a prefixpath
  cifs: remove bogus call to cifs_cleanup_volume_info

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] fix cpumask memory leak in acpi-cpufreq on cpu hotplug.

Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
  hp-wmi: fix use after free
  dell-laptop - using buffer without mutex_lock
  Revert: "dell-laptop: Toggle the unsupported hardware killswitch"
  platform-drivers-x86: set backlight type to BACKLIGHT_PLATFORM
  thinkpad-acpi: handle HKEY 0x4010, 0x4011 events
  drivers/platform/x86: Fix memory leak
  thinkpad-acpi: handle some new HKEY 0x60xx events
  acer-wmi: fix bitwise bug when set device state
  acer-wmi: Only update rfkill status for associated hotkey events

* 'movieboard' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: ohci: do not bind to Pinnacle cards, avert panic

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since we removed sti()/cli() and related, how about removing it from
Documentation/spinlocks.txt?
Signed-off-by: Muthukumar R <muthur@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

...as that function can sleep.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

[  191.310008] WARNING: kmemcheck: Caught 32-bit read from freed memory (f0d25f14)
[  191.310011] c056d2f088000000105fd2f00000000050415353040000000000000000000000
[  191.310020]  i i i i f f f f f f f f f f f f f f f f f f f f f f f f f f f f
[  191.310027]                                          ^
[  191.310029]
[  191.310032] Pid: 737, comm: modprobe Not tainted 3.0.0-rc5+ #268 Hewlett-Packard HP Compaq 6005 Pro SFF PC/3047h
[  191.310036] EIP: 0060:[<f80b3104>] EFLAGS: 00010286 CPU: 0
[  191.310039] EIP is at hp_wmi_perform_query+0x104/0x150 [hp_wmi]
[  191.310041] EAX: f0d25601 EBX: f0d25f00 ECX: 000121cf EDX: 000121ce
[  191.310043] ESI: f0d25f10 EDI: f0f97ea8 EBP: f0f97ec4 ESP: c173f34c
[  191.310045]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  191.310046] CR0: 8005003b CR2: f540c000 CR3: 30f30000 CR4: 000006d0
[  191.310048] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[  191.310050] DR6: ffff4ff0 DR7: 00000400
[  191.310051]  [<f80b317b>] hp_wmi_dock_state+0x2b/0x40 [hp_wmi]
[  191.310054]  [<f80b6093>] hp_wmi_init+0x93/0x1a8 [hp_wmi]
[  191.310057]  [<c10011f0>] do_one_initcall+0x30/0x170
[  191.310061]  [<c107ab9f>] sys_init_module+0xef/0x1a60
[  191.310064]  [<c149f998>] sysenter_do_call+0x12/0x28
[  191.310067]  [<ffffffff>] 0xffffffff
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

Using buffer->output[1] without mutex_lock()
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

This reverts commit a3d77411,

as it causes a mess in the wireless rfkill status on some models.
It is probably a bad idea to toggle the rfkill for all dell models
without the respect to the claim that it is hardware-controlled.

Cc: stable@kernel.org
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

Patch 2e711c04
(PM: Remove sysdev suspend, resume and shutdown operations)
deleted sysdev_suspend(), which was being relied on to call
check_wakeup_irqs() in suspend.  If check_wakeup_irqs() is not
called, wake interrupts that are pending when suspend is
entered may be lost.  It also breaks IRQCHIP_MASK_ON_SUSPEND,
which is handled in check_wakeup_irqs().

This patch adds a call to check_wakeup_irqs() in syscore_suspend(),
similar to what was deleted in sysdev_suspend().
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

I came across a memory leak during a cyclic cpu-online-offline test.
Signed-off-by: Yu Luming <luming.yu@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (pmbus) Improve auto-detection of temperature status register
  hwmon: (lm95241) Fix negative temperature results
  hwmon: (lm95241) Fix chip detection code

It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or
READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1.
Improve temperature status register detection to address this condition.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+

Negative temperatures were returned in degrees C instead of milli-Degrees C.
Also, negative temperatures were reported for remote temperature sensors even
if the chip was configured for positive-only results.

Fix by detecting temperature modes, and by treating negative temperatures
similar to positive temperatures, with appropriate sign extension.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix a copmile warning
  ASoC: ak4642: fixup snd_soc_update_bits mask for PW_MGMT2
  ALSA: hda - Change all ADCs for dual-adc switching mode for Realtek
  ASoC: Manage WM8731 ACTIVE bit as a supply widget
  ASoC: Don't set invalid name string to snd_card->driver field
  ASoC: Ensure we delay long enough for WM8994 FLL to lock when starting
  ASoC: Tegra: I2S: Ensure clock is enabled when writing regs
  ASoC: Fix Blackfin I2S _pointer() implementation return in bounds values
  ASoC: tlv320aic3x: Do soft reset to codec when going to bias off state
  ASoC: tlv320aic3x: Don't sync first two registers from register cache
  audio: tlv320aic26: fix PLL register configuration

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: conditional resource-reallocation through kernel parameter pci=realloc

* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6994/1: smp_twd: Fix typo in 'twd_timer_rate' printing
  ARM: 6987/1: l2x0: fix disabling function to avoid deadlock
  ARM: 6966/1: ep93xx: fix inverted RTS/DTR signals on uart1
  ARM: 6980/1: mmci: use StartBitErr to detect bad connections
  ARM: 6979/1: mach-vt8500: add forgotten irq_data conversion
  ARM: move memory layout sanity checking before meminfo initialization
  ARM: 6990/1: MAINTAINERS: add entry for ARM PMU profiling and debugging
  ARM: 6989/1: perf: do not start the PMU when no events are present
  ARM: dmabounce: fix map_single() error return value

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: clean up multiple crtc handling for evergreen+ (v2)

When firewire-ohci is bound to a Pinnacle MovieBoard, eventually a
"Register access failure" is logged and an interrupt storm or a kernel
panic happens.  https://bugzilla.kernel.org/show_bug.cgi?id=36622

Until this is sorted out (if that is going to succeed at all), let's
just prevent firewire-ohci from touching these devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>

Regression introduced in commit 724d9f1c.

Prior to that, expand_dfs_referral would regenerate the mount data string
and then call cifs_parse_mount_options to re-parse it (klunky, but it
worked). The above commit moved cifs_parse_mount_options out of cifs_mount,
so the re-parsing of the new mount options no longer occurred. Fix it by
making expand_dfs_referral re-parse the mount options.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

This needs to be done regardless of whether that KConfig option is set
or not.
Reported-by: Sven-Haegar Koch <haegar@sdinet.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

It's harmless but annyoing.
  sound/pci/hda/patch_realtek.c: In function ‘alc_cap_getput_caller’:
  sound/pci/hda/patch_realtek.c:2722:9: warning: ‘err’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge branch 'for-3.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into fix/asoc

Merge branch 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung

* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: S3C2440: fix section mismatch on mini2440
  ARM: S3C24XX: drop return codes in void function of dma.c
  ARM: S3C24XX: don't use uninitialized variable in dma.c
  ARM: EXYNOS4: Set appropriate I2C device variant
  ARM: S5PC100: Fix for compilation error
  spi/s3c64xx: Bug fix for SPI with different FIFO level
  ARM: SAMSUNG: Add tx_st_done variable
  ARM: EXYNOS4: Address a section mismatch w/ suspend issue.
  ARM: S5P: Fix bug on init of PWMTimers for HRTimer
  ARM: SAMSUNG: header file revised to prevent declaring duplicated
  ARM: EXYNOS4: fix improper gpio configuration
  ARM: EXYNOS4: Fix card detection for sdhci 0 and 2

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: max8997: Fix setting inappropriate value for ramp_delay variable
  regulator: db8500-prcmu: small fixes
  regulator: max8997: remove dependency on platform_data pointer
  regulator: MAX8997: Fix for divide by zero error
  regulator: max8952 - fix wrong gpio valid check

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  btrfs: fix oops when doing space balance
  Btrfs: don't panic if we get an error while balancing V2
  btrfs: add missing options displayed in mount output

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This driver handles the variants pca9530-pca9533, so it chose the name
"pca953x".  However, there is a gpio driver which decided on the same
name.  As a result, those two can't be loaded at the same time.  Add a
subsystem prefix to make the driver name unique.  Device matching will not
suffer, because both are I2C drivers which match using a
i2c_device_id-table which is not altered.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

remap_pfn_range() means map physical address pfn<<PAGE_SHIFT to user addr.

For nommu arch it's implemented by vma->vm_start = pfn << PAGE_SHIFT which
is wrong acroding the original meaning of this function.  And some driver
developer using remap_pfn_range() with correct parameter will get
unexpected result because vm_start is changed.  It should be implementd
like addr = pfn << PAGE_SHIFT but which is meanless on nommu arch, this
patch just make it simply return.

Parameter name and setting of vma->vm_flags also be fixed.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:

: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor  chip  - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK.  I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.

This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves.  Unfortunately,
this is not always the case.  The sleep is restored but as a parameter to
the probe function in the pdata.

[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>