The SPI core currently reports the MODALIAS uevent as "spi:<modalias>"
even for SPI devices that were registered by OF.

That means the OF module alias exported by MODULE_OF_TABLE(of,...) is
currently not used and user-space has no way to autoload this module.

But it is still a good practice to add the OF module alias information
into the kernel module even when it currently is unused so once the SPI
core is changed to report a correct OF modalias uevent, module
autoloading will be working for this driver.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

When 2 commands are submitted in a row, and the second is very quick,
the completion of the second command might never come. This happens
especially if the second command is quick, such as a status read after
an erase.

The issue is that in the interrupt handler, the status bits are cleared
after the new command is issued. There is a small temporal window where
this happens :
 - the previous command has set the command done bit
 - the ready for a command bit is set
 - the handler submits the next command
   - just then, the command completes, and the command done bit is still
     set
 - the handler clears the "previous" command done bit
 - the handler exits

In this flow, the "command done" of the next command will never trigger
a new interrupt to finish the status command, as it was cleared for both
commands.

Fix this by clearing the status bit before submitting a new command.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.

The bug is tricky : if the bootloader left a status bit set, the
unmasking of interrupts does trigger the interrupt handler before the
first command is issued, blocking the good behavior of the nand.

The same would happen if in pxa3xx_nand code flow a status bit is left,
and then a command is started.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

When keeping the configuration set by the bootloader (by using
the marvell,nand-keep-config property), the pxa3xx_nand_detect_config()
function is called and set the chunk size to 512 as a default value if
NDCR_PAGE_SZ is not set.

In the other case, when not keeping the bootloader configuration, no
chunk size is set. Fix this by adding a default chunk size of 512.

Fixes: 70ed8523 ("mtd: nand: pxa3xx: Introduce multiple page I/O
support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Remove extra space after the "platform:" prefix and make the alias matches
driver name.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

static analysis by smatch caught the following error:

drivers/mtd/maps/physmap_of.c:135 of_get_probes()
   error: potential null dereference 'res'.  (kzalloc returns null)

Check for failed kzalloc and return -ENOMEM in of_flash_probe if
this occurs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

If mtd_device_register() fails in nettel_init(), iomap left mapped.

The patch adds failure handling for mtd_device_register().

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

It is better to have device name prefixed the actual error message.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

In recent kernels we have a lot of helper functions, including
devres API, to make life of device driver developer easy.

Convert the driver using devm_kzalloc() and pcim_enable_device().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Let's use module_pci_driver() macro to reduce code base of the driver.

There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

There is no need to user to see the core part of the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Spansion S25FL204K is a 4-Mbit 3.0V Serial Flash Memory
with Uniform 4 kB Sectors.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The current "We only connect the NOR to this controller now." text
is not very clear, so explain it better by saying that generic SPI
is not supported by SPI_FSL_QUADSPI and only SPI NOR is.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Add SPI-NOR driver for the SPI Flash Interface (SPIFI)
controller that is found on newer NXP MCU devices.

The controller supports serial SPI Flash devices with 1-, 2-
and 4-bit width in either SPI mode 0 or 3. The controller
can operate in either command or memory mode. In memory mode
the Flash is exposed as normal memory and can be directly
accessed by the CPU.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Add device tree binding documentation for the SPI Flash Interface
(SPIFI) found on NXP LPC18xx and LPC43xx devies.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).

ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler.

Switch to use CONFIG_CPU_BIG_ENDIAN instead of __BIG_ENDIAN.

Fixes: 27c5b17c ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Erase function will use cmd 0x20 (SPINOR_OP_BE_4K) if kenrel enable option
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.

This command is not in fsl-quadspi driver LUT. So driver continue report
fsl-quadspi 21e0000.qspi: Unsupported cmd 0x20.

This patch fix this issue.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Han Xu <Han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The uboot may run the QuadSpi controler with command:
    #sf probe

So we should reset the module in the probe.
This patch also clear the pending interrupts which arised by the uboot
code.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

QSPI1 cannot wake up CCM from WAIT mode on SX ARD board, add pmqos to
let PM NOT enter WAIT mode when accessing QSPI1, refer to TKT245618.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Han Xu <Han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

We found there is a low probability(5%) QSPI access timeout issue,
usually it happened on kernel boot stage, the first time kernel tried to
access QSPI chip. The READ_ID command was sent but not executed,
consequently the probe function failed.

The root cause is that the divider is not glitchless in i.MX6SX chip.
If qspi clock enabled then change clock frequency by call clk_set_rate,
there will be glitch at low possiblity rate and pass to qspi controller.
The controler will be hang by this glitch.

Based on the new clock flag(CLK_SET_RATE_GATE) and new framework, we
need to change the approach of seting clock rate.
1. Disable clock.
2. call clk_set_rate.
3. Enable clock again.
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

new compatible string: "fsl,imx6ul-qspi".
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Add i.mx6ul chip support
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Han xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

new compatible string: "fsl,imx7d-qspi"
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Support i.mx7d.
quadspi in i.mx7d increase rxfifo.
require fill at least 16byte to trigger data transfer.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

add several quirk to distinguish different version of qspi module.
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

QSPI may failed to map enough memory (256MB) for AHB read in
previous implementation, especially in 3G/1G memory layout kernel.
Dynamically map memory to avoid such issue.

This implementation generally map QUADSPI_MAX_IOMAP (default 4MB) memory
for AHB read, it should be enough for common scenarios, and the side
effect (0.6% performance drop) is minor.

Previous implementation

root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=1K count=32K
32768+0 records in
32768+0 records out
33554432 bytes (34 MB) copied, 2.16006 s, 15.5 MB/s

root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=32M count=1
1+0 records in
1+0 records out
33554432 bytes (34 MB) copied, 1.43149 s, 23.4 MB/s

After applied the patch

root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=1K count=32K
32768+0 records in
32768+0 records out
33554432 bytes (34 MB) copied, 2.1743 s, 15.4 MB/s

root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=32M count=1
1+0 records in
1+0 records out
33554432 bytes (34 MB) copied, 1.43158 s, 23.4 MB/s
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

When we added the "jedec,spi-nor" compatible string for use in this
driver, we added it as a modalias option. The modalias can be derived in
different ways for platform devices vs. device tree (of_*) matching. But
for device tree matching (the primary target of this identifier string),
the modalias is determined from the first entry in the 'compatible'
property. IOW, the following properties would bind to this driver:

	// Option (a), modalias = "spi-nor"
	compatible = "jedec,spi-nor";

	// Option (b), modalias = "spi-nor"
	compatible = "idontknowwhatimdoing,spi-nor";

But the following would not:

	// Option (c), modalias = "shinynewdevice"
	compatible = "myvendor,shinynewdevice", "jedec,spi-nor";

So, we'd like to match (a) and (c) (even when we don't have an explicit
entry for "shinynewdevice"), and we'd rather not allow (b).

To do this, we
  (1) always (for devices without specific platform data) pass the
      modalias to the spi-nor library;
  (2) rework the spi-nor library to not reject "bad" names, and
      instead just fall back to autodetection; and
  (3) add the .of_match_table to properly catch all "jedec,spi-nor".

This allows (a) and (c) without warnings, and rejects (b).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Replaces the hard coded "always use EDO" policy with that prescribed
by the ONFI 3.1 specification that EDO mode should always be used if tRC
is below 30ns.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The TIMING_CFG register was previously statically set to a magic value
(extracted from Allwinner's BSP) when initializing the NAND controller.
Now that we have more details about the TIMING_CFG register layout
(extracted from the A83 user manual) we can dynamically calculate the
appropriate value for each NAND chip and set it when selecting the
chip.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Micron n25q064 flash supports 4 KiB erase sectors.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

QUADSPI_MCR_CLR_TXF_MASK is the correct mask for clearing the TX FIFO.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

r852_ecc_correct() reads a 32-bit register into a 16-bit variable,
ecc_reg, but this variable is later used as if it was larger.  This is
reported by clang when building the kernel with many warnings:

    drivers/mtd/nand/r852.c:512:11: error: shift count >= width of type
    [-Werror,-Wshift-count-overflow]
                    ecc_reg >>= 16;
                            ^   ~~
Fix this by making ecc_reg 32-bit, like the return type of
r852_read_reg_dword().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

It is needed for k2l keystone2 EVM which uses NAND flash with 4K page
size, hence add support for 4K page size nand devices.

[Brian: similar work submitted by Murali Karicheri <m-karicheri2@ti.com>
and Hao Zhang <hzhang@ti.com>]
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Commit 66507c7b ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer") added a flag NAND_USE_BOUNCE_BUFFER
using the same bit value as the existing NAND_BUSWIDTH_AUTO.

Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Fixes: 66507c7b ("mtd: nand: Add support to use nand_base
	poi databuf as bounce buffer")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Do not call free_device() in init_nandsim, the caller - ns_init_module -
will take care of that if something goes wrong.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

If allocating ns->nand_pages_slab fails, do not try to destroy it when
cleaning up nandsim resources.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>