Skip to content

L
linux
Switch branch/tag
  1. 18 Feb, 2014 4 commits
    • Sachin Kamat's avatar
      usb: gadget: s3c2410_udc: Fix build error · d246c9d5
      Sachin Kamat authored 
      Pass value instead of address as expected by 'usb_ep_set_maxpacket_limit'.
Fixes the following compilation error introduced by commit e117e742
("usb: gadget: add "maxpacket_limit" field to struct usb_ep"):

drivers/usb/gadget/s3c2410_udc.c: In function ‘s3c2410_udc_reinit’:
drivers/usb/gadget/s3c2410_udc.c:1632:3: error:
cannot take address of bit-field ‘maxpacket’
   usb_ep_set_maxpacket_limit(&ep->ep, &ep->ep.maxpacket);
Signed-off-by: default avatarSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: default avatarRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      d246c9d5
    • Roger Quadros's avatar
      usb: musb: core: Fix remote-wakeup resume · 33f8d75f
      Roger Quadros authored 
      During resume don't touch SUSPENDM/RESUME bits of POWER register
while restoring controller context. These bits might be changed
by the controller during resume operation and so will be different
than what they were during suspend.

e.g. SUSPENDM bit is set by software during USB global suspend but
automatically cleared by the controller during remote wakeup or
during resume. Setting this bit back while restoring context
causes undesired behaviour. i.e. Babble interrupt is generated
and USB is broken.
Signed-off-by: default avatarRoger Quadros <rogerq@ti.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      33f8d75f
    • Ajay Kumar Gupta's avatar
      usb: musb: host: Fix SuperSpeed hub enumeration · 3c4653c1
      Ajay Kumar Gupta authored 
      Disables PING on status phase of control transfer.
PING token is not mandatory in status phase of control transfer
and so some high speed USB devices don't support it. If such devices
are connected to MUSB then they would not respond to PING token
causing delayed or failed enumeration.

[Roger Q] Fixes enumeration issues with some Super-Speed USB hubs
e.g. Dlink DUB-1340
Signed-off-by: default avatarAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: default avatarRoger Quadros <rogerq@ti.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      3c4653c1
    • Felipe Balbi's avatar
      usb: musb: fix obex in g_nokia.ko causing kernel panic · 30a70b02
      Felipe Balbi authored 
      phy_power_off() can, depending on the PHY being used,
start I2C transactions which shouldn't happen in
atomic context.

Current call to phy_power_off() inside omap2430_runtime
callbacks causes the following dump, as a fix, just don't
power off the PHY in runtime.

[   18.606414] [<c037eac0>] (__schedule+0x5c/0x50c) from [<c037d3bc>] (schedule_timeout+0x1f4/0x25c)
[   18.623809] [<c037d3bc>] (schedule_timeout+0x1f4/0x25c) from [<c037f12c>] (wait_for_common+0xc8/0x1ac)
[   18.649291] [<c037f12c>] (wait_for_common+0xc8/0x1ac) from [<c028c1c0>] (omap_i2c_xfer+0x338/0x488)
[   18.674499] [<c028c1c0>] (omap_i2c_xfer+0x338/0x488) from [<c0288144>] (__i2c_transfer+0x40/0x74)
[   18.692047] [<c0288144>] (__i2c_transfer+0x40/0x74) from [<c0288a2c>] (i2c_transfer+0x6c/0x90)
[   18.709320] [<c0288a2c>] (i2c_transfer+0x6c/0x90) from [<c02351c8>] (regmap_i2c_read+0x48/0x68)
[   18.726715] [<c02351c8>] (regmap_i2c_read+0x48/0x68) from [<c023161c>] (_regmap_raw_read+0x128/0x220)
[   18.752685] [<c023161c>] (_regmap_raw_read+0x128/0x220) from [<c02317b4>] (regmap_raw_read+0xa0/0x130)
[   18.779052] [<c02317b4>] (regmap_raw_read+0xa0/0x130) from [<c023193c>] (regmap_bulk_read+0xf8/0x16c)
[   18.805694] [<c023193c>] (regmap_bulk_read+0xf8/0x16c) from [<c0238ea8>] (twl_i2c_read+0xa4/0xe0)
[   18.823730] [<c0238ea8>] (twl_i2c_read+0xa4/0xe0) from [<c0274d34>] (__twl4030_phy_power.isra.12+0x1c/0x58)
[   18.850921] [<c0274d34>] (__twl4030_phy_power.isra.12+0x1c/0x58) from [<c0274df0>]
(twl4030_phy_power.part.14+0x80/0xc8)
[   18.879699] [<c0274df0>] (twl4030_phy_power.part.14+0x80/0xc8) from [<c0274f9c>]
(twl4030_set_suspend+0x54/0x1e8)
[   18.908325] [<c0274f9c>] (twl4030_set_suspend+0x54/0x1e8) from [<c027c8c4>]
(omap2430_runtime_resume+0x5c/0x64)
[   18.937042] [<c027c8c4>] (omap2430_runtime_resume+0x5c/0x64) from [<c0225dd0>]
(pm_generic_runtime_resume+0x2c/0x38)
[   18.966461] [<c0225dd0>] (pm_generic_runtime_resume+0x2c/0x38) from [<c0229fe0>] (__rpm_callback+0x54/0x80)
[   18.995117] [<c0229fe0>] (__rpm_callback+0x54/0x80) from [<c022a04c>] (rpm_callback+0x40/0x74)
[   19.013610] [<c022a04c>] (rpm_callback+0x40/0x74) from [<c022b3c8>] (rpm_resume+0x448/0x63c)
[   19.031921] [<c022b3c8>] (rpm_resume+0x448/0x63c) from [<c022b2e4>] (rpm_resume+0x364/0x63c)
[   19.050140] [<c022b2e4>] (rpm_resume+0x364/0x63c) from [<c022b874>] (__pm_runtime_resume+0x48/0x74)
[   19.077728] [<c022b874>] (__pm_runtime_resume+0x48/0x74) from [<c027b4fc>] (musb_gadget_pullup+0x1c/0xb4)
[   19.105895] [<c027b4fc>] (musb_gadget_pullup+0x1c/0xb4) from [<bf025c14>] (usb_function_deactivate+0x54/0xa4
[libcomposite])
[   19.135955] [<bf025c14>] (usb_function_deactivate+0x54/0xa4 [libcomposite]) from [<bf05b3b8>]
(obex_bind+0x124/0x1d8 [usb_f_obex])
[   19.166870] [<bf05b3b8>] (obex_bind+0x124/0x1d8 [usb_f_obex]) from [<bf025794>] (usb_add_function+0x58/0xf4
[libcomposite])
[   19.197143] [<bf025794>] (usb_add_function+0x58/0xf4 [libcomposite]) from [<bf037420>]
(nokia_bind_config+0x204/0x250 [g_nokia])
[   19.227905] [<bf037420>] (nokia_bind_config+0x204/0x250 [g_nokia]) from [<bf0263fc>] (usb_add_config+0x28/0xc0
[libcomposite])
[   19.258483] [<bf0263fc>] (usb_add_config+0x28/0xc0 [libcomposite]) from [<bf03709c>] (nokia_bind+0x9c/0x21c
[g_nokia])
[   19.288421] [<bf03709c>] (nokia_bind+0x9c/0x21c [g_nokia]) from [<bf0275bc>] (composite_bind+0x74/0x180
[libcomposite])
[   19.318420] [<bf0275bc>] (composite_bind+0x74/0x180 [libcomposite]) from [<c027d658>]
(udc_bind_to_driver+0x2c/0xc4)
[   19.348114] [<c027d658>] (udc_bind_to_driver+0x2c/0xc4) from [<c027d764>] (usb_gadget_probe_driver+0x74/0x94)
[   19.377166] [<c027d764>] (usb_gadget_probe_driver+0x74/0x94) from [<c00086f8>] (do_one_initcall+0x94/0x138)
[   19.406005] [<c00086f8>] (do_one_initcall+0x94/0x138) from [<c007a460>] (load_module+0x113c/0x13c4)
[   19.434051] [<c007a460>] (load_module+0x113c/0x13c4) from [<c007a7b4>] (SyS_init_module+0xcc/0xec)
[   19.462127] [<c007a7b4>] (SyS_init_module+0xcc/0xec) from [<c000dd40>] (ret_fast_syscall+0x0/0x30)
[   19.490753] Code: 0a00002e e1a00004 eb001438 e598300c (e5d3202c)
[   19.506805] ---[ end trace 060b62ec0d68a78b ]---
[   19.523132] Kernel panic - not syncing: Fatal exception in interrupt

dump is from 3.12-rc5 kernel
Reported-by: default avatarPali Rohár <pali.rohar@gmail.com>
Signed-off-by: default avatarIvaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      30a70b02
  3. 11 Feb, 2014 2 commits
    • Raymond Wanyoike's avatar
      usb: option: blacklist ZTE MF667 net interface · 3635c7e2
      Raymond Wanyoike authored 
      Interface #5 of 19d2:1270 is a net interface which has been submitted to the
qmi_wwan driver so consequently remove it from the option driver.
Signed-off-by: default avatarRaymond Wanyoike <raymond.wanyoike@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      3635c7e2
    • Greg Kroah-Hartman's avatar
      Merge tag 'for-usb-linus-2014-02-11' of... · 2991942f
      Greg Kroah-Hartman authored 
      Merge tag 'for-usb-linus-2014-02-11' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Sarah writes:

xhci: Revert TD fragment hacks.

Hi Greg,

Recently, we found that commit "35773dac "usb: xhci: Link TRB must not
occur within a USB payload burst" causes a userspace regression.  It will
cause larger transfers submitted through usbfs that would have succeeded
on older kernels to be rejected.

Commit 35773dac was designed to address an issue where an ASIX USB
ethernet device would get wedged when it was connected to a 1.0 xHCI
host.  Only this particular ethernet device was impacted, because only the
ax88179_178a driver implemented scatter-gather in 3.12.  The xHCI driver
doesn't currently support TD fragment rules, and commit 35773dac was a
quick hack that partially implemented one of the rules.

This is the third regression this patch has caused.  There's yet another
quick hack to work around the issue, but I really want to support TD
fragments properly, rather than hacking around it.  It will take us a
kernel release or two to get it implemented, since it is a big
architectural change.

This patchset backs out commit 35773dac, and the two bug fix patches
for it.  The first patch limits arbitrarily aligned scatter-gather under
xHCI 1.0 hosts.

As a result of this patchset:

1. usb-storage and uas will still be able to use scatter-gather, since
   they submit max packet sized aligned transfers.
2. usbfs will behave exactly as before, no more userspace regressions.
3. The ax88179_178a driver works fine without scatter-gather (Mark Lord
   confirms this).

Users of the ASIX chipset may still see occasional packet loss on 1.0 xHCI
hosts, if the xHCI driver needs to split a TRB across 64-KB boundaries,
and a link TRB happens to fall between those two TRBs.  I expect this
corner case to be infrequent.

Sarah Sharp
      2991942f
  5. 07 Feb, 2014 5 commits
    • Sarah Sharp's avatar
      Revert "usb: xhci: Link TRB must not occur within a USB payload burst" · 3d4b81ed
      Sarah Sharp authored 
      This reverts commit 35773dac.  It's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  Commit 70cabb7d992f "xhci 1.0: Limit
arbitrarily-aligned scatter gather." should fix the issues seen with the
ax88179_178a driver on xHCI 1.0 hosts, without causing regressions.
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12
      3d4b81ed
    • Sarah Sharp's avatar
      Revert "xhci: Avoid infinite loop when sg urb requires too many trbs" · 9cf00d91
      Sarah Sharp authored 
      This reverts commit d6c9ea90.

We are ripping out commit 35773dac "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  This commit attempted to fix the
issues with that patch.
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12
      9cf00d91
    • Sarah Sharp's avatar
      Revert "xhci: Set scatter-gather limit to avoid failed block writes." · 1386ff75
      Sarah Sharp authored 
      This reverts commit f2d9b991.

We are ripping out commit 35773dac "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  This commit attempted to fix the
issues with that patch.
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org #3.12
      1386ff75
    • Sarah Sharp's avatar
      xhci 1.0: Limit arbitrarily-aligned scatter gather. · 247bf557
      Sarah Sharp authored 
      xHCI 1.0 hosts have a set of requirements on how to align transfer
buffers on the endpoint rings called "TD fragment" rules.  When the
ax88179_178a driver added support for scatter gather in 3.12, with
commit 804fad45411b48233b48003e33a78f290d227c8 "USBNET: ax88179_178a:
enable tso if usb host supports sg dma", it broke the device under xHCI
1.0 hosts.  Under certain network loads, the device would see an
unexpected short packet from the host, which would cause the device to
stop sending ethernet packets, even through USB packets would still be
sent.

Commit 35773dac "usb: xhci: Link TRB must not occur within a USB
payload burst" attempted to fix this.  It was a quick hack to partially
implement the TD fragment rules.  However, it caused regressions in the
usb-storage layer and userspace USB drivers using libusb.  The patches
to attempt to fix this are too far reaching into the USB core, and we
really need to implement the TD fragment rules correctly in the xHCI
driver, instead of continuing to wallpaper over the issues.

Disable arbitrarily-aligned scatter-gather in the xHCI driver for 1.0
hosts.  Only the ax88179_178a driver checks the no_sg_constraint flag,
so don't set it for 1.0 hosts.  This should not impact usb-storage or
usbfs behavior, since they pass down max packet sized aligned sg-list
entries (512 for USB 2.0 and 1024 for USB 3.0).
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: default avatarMark Lord <mlord@pobox.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org # 3.12
      247bf557
    • Jan Moskyto Matejka's avatar
      Modpost: fixed USB alias generation for ranges including 0x9 and 0xA · 03b56329
      Jan Moskyto Matejka authored 
      Commit afe2dab4 ("USB: add hex/bcd detection to usb modalias generation")
changed the routine that generates alias ranges. Before that change, only
digits 0-9 were supported; the commit tried to fix the case when the range
includes higher values than 0x9.

Unfortunately, the commit didn't fix the case when the range includes both
0x9 and 0xA, meaning that the final range must look like [x-9A-y] where
x <= 0x9 and y >= 0xA -- instead the [x-9A-x] range was produced.

Modprobe doesn't complain as it sees no difference between no-match and
bad-pattern results of fnmatch().

Fixing this simple bug to fix the aliases.
Also changing the hardcoded beginning of the range to uppercase as all the
other letters are also uppercase in the device version numbers.

Fortunately, this affects only the dvb-usb-dib0700 module, AFAIK.
Signed-off-by: default avatarJan Moskyto Matejka <mq@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      03b56329
  7. 05 Feb, 2014 3 commits
  9. 04 Feb, 2014 10 commits
  11. 03 Feb, 2014 4 commits
    • Linus Torvalds's avatar
      Linus 3.14-rc1 · 38dbfb59
      Linus Torvalds authored
      38dbfb59
    • Linus Torvalds's avatar
      Merge branch 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux · 69048e01
      Linus Torvalds authored 
      Pull parisc updates from Helge Deller:
 "The three major changes in this patchset is a implementation for
  flexible userspace memory maps, cache-flushing fixes (again), and a
  long-discussed ABI change to make EWOULDBLOCK the same value as
  EAGAIN.

  parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
  to keep HP-UX compatibility.  Since we will probably never implement
  full HP-UX support, we prefer to drop this compatibility to make it
  easier for us with Linux userspace programs which mostly never checked
  for both values.  We don't expect major fall-outs because of this
  change, and if we face some, we will simply rebuild the necessary
  applications in the debian archives"

* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: add flexible mmap memory layout support
  parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
  parisc: convert uapi/asm/stat.h to use native types only
  parisc: wire up sched_setattr and sched_getattr
  parisc: fix cache-flushing
  parisc/sti_console: prefer Linux fonts over built-in ROM fonts
      69048e01
    • Mikulas Patocka's avatar
      hpfs: optimize quad buffer loading · 1c0b8a7a
      Mikulas Patocka authored 
      HPFS needs to load 4 consecutive 512-byte sectors when accessing the
directory nodes or bitmaps.  We can't switch to 2048-byte block size
because files are allocated in the units of 512-byte sectors.

Previously, the driver would allocate a 2048-byte area using kmalloc,
copy the data from four buffers to this area and eventually copy them
back if they were modified.

In the current implementation of the buffer cache, buffers are allocated
in the pagecache.  That means that 4 consecutive 512-byte buffers are
stored in consecutive areas in the kernel address space.  So, we don't
need to allocate extra memory and copy the content of the buffers there.

This patch optimizes the code to avoid copying the buffers.  It checks
if the four buffers are stored in contiguous memory - if they are not,
it falls back to allocating a 2048-byte area and copying data there.
Signed-off-by: default avatarMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      1c0b8a7a
    • Mikulas Patocka's avatar
      hpfs: remember free space · 2cbe5c76
      Mikulas Patocka authored 
      Previously, hpfs scanned all bitmaps each time the user asked for free
space using statfs.  This patch changes it so that hpfs scans the
bitmaps only once, remembes the free space and on next invocation of
statfs it returns the value instantly.

New versions of wine are hammering on the statfs syscall very heavily,
making some games unplayable when they're stored on hpfs, with load
times in minutes.

This should be backported to the stable kernels because it fixes
user-visible problem (excessive level load times in wine).
Signed-off-by: default avatarMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      2cbe5c76
  13. 02 Feb, 2014 12 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7