Introduce the next neighbor (NN) capability in chip_info as NN registers
are not supported in certain SKUs of QAT.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Modify condition in qat_uclo_wr_mimage() to use a capability of the
device (sram_visible), rather than the device ID, so the check is not
specific to devices of the same type.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Introduce the chip info structure which contains device specific
information. The initialization path has been split between common and
hardware specific in order to facilitate the introduction of the next
generation hardware.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Replace long expressions with local variables in the functions
qat_uclo_wr_uimage_page(), qat_uclo_init_globals() and
qat_uclo_init_umem_seg() to improve readability.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Refactor qat_uclo_set_ae_mode() by moving the logic that sets the AE
modes to a separate function, qat_hal_set_modes().
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Move the definition of ICP_QAT_AE_OFFSET, ICP_QAT_CAP_OFFSET,
LOCAL_TO_XFER_REG_OFFSET and ICP_QAT_EP_OFFSET from qat_hal.c to
icp_qat_hal.h to avoid the definition of generation specific constants
in qat_hal.c.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Include the offset of GLOBAL_CSR directly into the enum hal_global_csr
and remove the macros SET_GLB_CSR/GET_GLB_CSR to simplify the global CSR
access.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Change the API and the behaviour of the qat_hal_start() function.
With this change, the function starts under the hood all acceleration
engines (AEs) and there is no longer need to call it for each engine.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Change micro word data mask since the Acceleration Engine (AE)
instruction codes have been changed in the new generation QAT devices.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Change type for ctx_mask from unsigned char to unsigned long to avoid
type casting.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Improve the way micro instructions (FW code) are uploaded to Accelerator
Engines (AEs). If code starts at PC zero (absolute addressing), read
uwords with no relative address. Otherwise, use relative addressing to
the page region.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Rename the function qat_uclo_del_uof_obj() in qat_uclo_del_obj() since
it frees the memory allocated for all firmware objects.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Introduce additional parenthesis to resolve a warninga reported by
checkpatch.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove unnecessary parenthesis across the firmware loader.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Change message in error path of qat_uclo_check_image_compat() to report
an incompatible firmware image that contains a neighbor register table.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Do not mask the AE number with the AE mask when accessing the AE local
CSRs. Bit 12 of the local CSR address is the start of AE number so just
take out the AE mask here.
Signed-off-by: Jack Xu <jack.xu@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The return value of qat_hal_rd_ae_csr() is always a CSR value and never
a status and should not be stored in the status variable of
qat_hal_put_rel_rd_xfer().

This removes the assignment as qat_hal_rd_ae_csr() is not expected to
fail.
A more comprehensive handling of the theoretical corner case which could
result in a fail will be submitted in a separate patch.

Fixes: 8c9478a4 ("crypto: qat - reduce stack size with KASAN")
Signed-off-by: Jack Xu <jack.xu@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Implement infrastructure for the Multiple Object File (MOF) format
in the firmware loader. This will allow to load a specific firmware
image contained inside an MOF file.

This patch is based on earlier work done by Pingchao Yang.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Jack Xu <jack.xu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch fixes all the sparse warnings in cavium/nitrox:

- Fix endianness warnings by adding the correct markers to unions.
- Add missing header inclusions for prototypes.
- Move nitrox_sriov_configure prototype into the isr header file.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Change all lower case pci in comments to be upper case PCI.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The current NEON based ChaCha implementation for ARM is optimized for
multiples of 4x the ChaCha block size (64 bytes). This makes sense for
block encryption, but given that ChaCha is also often used in the
context of networking, it makes sense to consider arbitrary length
inputs as well.

For example, WireGuard typically uses 1420 byte packets, and performing
ChaCha encryption involves 5 invocations of chacha_4block_xor_neon()
and 3 invocations of chacha_block_xor_neon(), where the last one also
involves a memcpy() using a buffer on the stack to process the final
chunk of 1420 % 64 == 12 bytes.

Let's optimize for this case as well, by letting chacha_4block_xor_neon()
deal with any input size between 64 and 256 bytes, using NEON permutation
instructions and overlapping loads and stores. This way, the 140 byte
tail of a 1420 byte input buffer can simply be processed in one go.

This results in the following performance improvements for 1420 byte
blocks, without significant impact on power-of-2 input sizes. (Note
that Raspberry Pi is widely used in combination with a 32-bit kernel,
even though the core is 64-bit capable)

   Cortex-A8  (BeagleBone)       :   7%
   Cortex-A15 (Calxeda Midway)   :  21%
   Cortex-A53 (Raspberry Pi 3)   :   3%
   Cortex-A72 (Raspberry Pi 4)   :  19%

Cc: Eric Biggers <ebiggers@google.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove cast for mailbox CSR in adf_admin.c as it is not needed.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The extra tests in the manager actually require the manager to be
selected too. Otherwise the linker gives errors like:

ld: arch/x86/crypto/chacha_glue.o: in function `chacha_simd_stream_xor':
chacha_glue.c:(.text+0x422): undefined reference to `crypto_simd_disabled_for_test'

Fixes: 2343d152 ("crypto: Kconfig - allow tests to be disabled when manager is disabled")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

At the time xts fallback tfm allocation fails the device struct
hasn't been enabled yet in the caam xts tfm's private context.

Fix this by using the device struct from xts algorithm's private context
or, when not available, by replacing dev_err with pr_err.

Fixes: 9d9b14db ("crypto: caam/jr - add fallback for XTS with more than 8B IV")
Fixes: 83e8aa91 ("crypto: caam/qi - add fallback for XTS with more than 8B IV")
Fixes: 36e2d7cf ("crypto: caam/qi2 - add fallback for XTS with more than 8B IV")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

'hisi_qm_init' initializes configuration of QM.
To improve code readability, split it into two pieces.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

'qm_eq_ctx_cfg' initializes configuration of EQ and AEQ,
split it into two pieces to improve code readability.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

'qm_qp_ctx_cfg' initializes configuration of SQ and CQ,
split it into two pieces to improve code readability.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Replace 'sprintf' with 'scnprintf' to avoid overrun.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Since 'qm_set_sqctype' always returns 0, change it as 'void'.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Since 'qm_create_debugfs_file' always returns 0, change it as 'void'.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The returns of 'qm_get_hw_error_status' and 'qm_get_dev_err_status'
are values from the hardware registers, which should not be defined
as 'int', so update as 'u32'.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Some numbers are replaced by macros to avoid incomprehension.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Clean up the check for irq. dev_err() is superfluous as
platform_get_irq() already prints an error. Check for zero
would indicate a bug. Remove curly braces to conform to
styling requirements.
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Loading the module deadlocks since:
-local cbc(aes) implementation needs a fallback and
-crypto API tries to find one but the request_module() resolves back to
the same module

Fix this by changing the module alias for cbc(aes) and
using the NEED_FALLBACK flag when requesting for a fallback algorithm.

Fixes: 00b99ad2 ("crypto: arm/aes-neonbs - Use generic cbc encryption path")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

A semicolon is not needed after a switch statement.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

A semicolon is not needed after a switch statement.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

PAC pointer authentication signs the return address against the value
of the stack pointer, to prevent stack overrun exploits from corrupting
the control flow. However, this requires that the AUTIASP is issued with
SP holding the same value as it held when the PAC value was generated.
The Poly1305 NEON code got this wrong, resulting in crashes on PAC
capable hardware.

Fixes: f569ca16 ("crypto: arm64/poly1305 - incorporate OpenSSL/CRYPTOGAMS ...")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Commit 3f69cc60 ("crypto: af_alg - Allow arbitrarily long algorithm
names") made the kernel start accepting arbitrarily long algorithm names
in sockaddr_alg.  However, the actual length of the salg_name field
stayed at the original 64 bytes.

This is broken because the kernel can access indices >= 64 in salg_name,
which is undefined behavior -- even though the memory that is accessed
is still located within the sockaddr structure.  It would only be
defined behavior if the array were properly marked as arbitrary-length
(either by making it a flexible array, which is the recommended way
these days, or by making it an array of length 0 or 1).

We can't simply change salg_name into a flexible array, since that would
break source compatibility with userspace programs that embed
sockaddr_alg into another struct, or (more commonly) declare a
sockaddr_alg like 'struct sockaddr_alg sa = { .salg_name = "foo" };'.

One solution would be to change salg_name into a flexible array only
when '#ifdef __KERNEL__'.  However, that would keep userspace without an
easy way to actually use the longer algorithm names.

Instead, add a new structure 'sockaddr_alg_new' that has the flexible
array field, and expose it to both userspace and the kernel.
Make the kernel use it correctly in alg_bind().

This addresses the syzbot report
"UBSAN: array-index-out-of-bounds in alg_bind"
(https://syzkaller.appspot.com/bug?extid=92ead4eb8e26a26d465e).

Reported-by: syzbot+92ead4eb8e26a26d465e@syzkaller.appspotmail.com
Fixes: 3f69cc60 ("crypto: af_alg - Allow arbitrarily long algorithm names")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use the new crypto_engine_alloc_init_and_set() function to
initialize crypto-engine and enable retry mechanism.

Set the maximum size for crypto-engine software queue based on
Job Ring size (JOBR_DEPTH) and a threshold (reserved for the
non-crypto-API requests that are not passed through crypto-engine).

The callback for do_batch_requests is NULL, since CAAM
doesn't support linked requests.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently, by default crypto self-test failures only result in a
pr_warn() message and an "unknown" status in /proc/crypto.  Both of
these are easy to miss.  There is also an option to panic the kernel
when a test fails, but that can't be the default behavior.

A crypto self-test failure always indicates a kernel bug, however, and
there's already a standard way to report (recoverable) kernel bugs --
the WARN() family of macros.  WARNs are noisier and harder to miss, and
existing test systems already know to look for them in dmesg or via
/proc/sys/kernel/tainted.

Therefore, call WARN() when an algorithm fails its self-tests.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>