Allow to use enum items for variables initialization.
For this, move enums upper in the code.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-3-gnstark@sberdevices.ruSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Remove IIO_CHAN_SOFT_TIMESTAMP channel because it's used only for
buffering mode which is not implemented.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-2-gnstark@sberdevices.ruSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch adds pressure compensation to the scd4x driver. The pressure can
be written to the sensor in hPa. The pressure will be compensated
internally by the sensor.
Signed-off-by: Roan van Dijk <roan@protonic.nl>
Link: https://lore.kernel.org/r/20230711101419.2065107-1-roan@protonic.nlSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In `iio_trigger_detach_poll_func()` the return value from
`trig->ops->set_trigger_state(trig, false)` is checked with `if (ret)`.
However, in `iio_trigger_attach_poll_func()` it is checked with
`if (ret < 0)`. Resolve this mismatch by only checking for `if (ret)` in
both places.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/pndv8eojdey.fsf@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Each of qcom,spmi-adc7-pm*.h headers define a set of ADC channels that
can be used for monitoring on thie particular chip. Switch them to use
channel IDs defined in the dt-bindings/iio/qcom,spmi-vadc.h header
instead of specifying the numeric IDs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230707123027.1510723-2-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Enable buffered reading of samples from the LMP92064 ADC.
The main benefit of this change is being able to read out current and
voltage measurements in a single transfer, allowing instantaneous power
measurements.

Reads into the buffer can be triggered by any software triggers, e.g.
the iio-trig-hrtimer:

    $ mkdir /sys/kernel/config/iio/triggers/hrtimer/my-trigger
    $ cat /sys/bus/iio/devices/iio\:device3/name
    lmp92064
    $ iio_readdev -t my-trigger -b 16 iio:device3 | hexdump
    WARNING: High-speed mode not enabled
    0000000 0000 0176 0101 0001 5507 abd5 7645 1768
    0000010 0000 016d 0101 0001 ee1e ac6b 7645 1768
    ...
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230707063635.1496437-1-l.goehrs@pengutronix.deSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230704095808.33780-1-frank.li@vivo.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Even though it existed in bindings for the longest time,
ADC5_GPIO2_100K_PU was never assigned in the driver. Do so.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230627-topic-adc-v1-1-c61581abffa3@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

When processing data read the full fifo data in 1 time. If there
are several samples in the FIFO, it means we are experiencing
system delay. In this case, it is better to read all data with 1
bus access than to add additional latency by doing several ones.

This requires to use a bigger buffer depending on chip FIFO size
and do an additional local data copy before sending. But the cost
is minimal and behavior is still better like this under system
heavy load.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230623082924.283967-1-inv.git-commit@tdk.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Datarate (dr) is a 3-bit wide register field. Values from 0 to 7 are
allowed for all devices but only for the ADS1115 devices a value of 7
does make a difference.

While on it fix the description of the datarate for ADS1115 devices as
well.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230621160857.3400747-1-m.felsch@pengutronix.deSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Replace scnprintf with sysfs_emit_at which is the preferred alternative.

Also make sure each fractional digit is in its place by padding with
zeros up to 3 digits: "...%03d...".
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230620163135.93780-1-alisa.roman@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Allwinner's D1/T113s/R329/T507 SoCs have a new general purpose ADC.
This ADC is the same for all of this SoCs. The only difference is
the number of available channels.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-4-bigunclemax@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The General Purpose ADC (GPADC) can convert the external signal into
a certain proportion of digital value, to realize the measurement of
analog signal, which can be applied to power detection and key detection.

Theoretically, this ADC can support up to 16 channels. All SoCs below
contain this GPADC IP. The only difference between them is the number
of available channels:

 T113 - 1 channel
 D1   - 2 channels
 R329 - 4 channels
 T507 - 4 channels
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-3-bigunclemax@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch adds SoCs names to Allwinner GPADC description to
make it more informative.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-2-bigunclemax@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The calibration bias is setting the LED current to change the detection
distance. Add read/write attribute for proximity calibration bias and
read attribute for available values. This is supported for vcnl4040 and
vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-9-astrid.rost@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add the proximity multi pulse (PS_MPS) as oversampling_ratio.
Instead of one single pulse per every defined time frame, one can
program2, 4, or even 8 pulses. This leads to a longer IRED on-time
for each proximity measurement value, which also results in a higher
detection range.

Add read/write attribute for proximity oversampling-ratio and read
attribute for available oversampling-ratio.
This is supported for vcnl4040 and vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-8-astrid.rost@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add read/write attribute for proximity and illuminance period. The
period is set in the interrupt persistence flags(PS_PERS and ALS_PERS).
An interrupt will not be asserted if the raw value is not over (or lower)
than the threshold for the set continued amount of measurements.
The time in seconds is calculated by the number of continued refreshes
multiplied with the integration time.
It will always pick the next lower possible value. The period changes,
if the integration time is changed.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-7-astrid.rost@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support to configure ambient light sensor interrupts and threshold
limits for vcnl4040 and vcnl4200. If an interrupt is detected an event
will be pushed to the event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-6-astrid.rost@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add illuminance integration time for vcnl4040 and vcnl4200.
Add read/write attribute for illuminance integration time and read
attribute for available integration times.
Set scale and sampling rate according to the integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-5-astrid.rost@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Check IIO_PROXIMITY  with switch case in order to make it easier
to add further types like light.
Add check for IIO_EV_INFO_VALUE for writing rising or falling events.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-4-astrid.rost@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add ps_it attributes for vcnl4200 (similar to vcnl4040).
Add read/write attribute for proximity integration time.
Read attribute for available proximity integration times.
Change sampling rate depending on integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-3-astrid.rost@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add proximity interrupt support for vcnl4200 (similar to vcnl4040).
Add support to configure proximity sensor interrupts and threshold
limits. If an interrupt is detected an event will be pushed to the
event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-2-astrid.rost@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The DA217 accelerometer is another DA280 compatible accelerometer,
add its device-ids to the da280 driver.
Reported-by: Juno Computers USA <usa@junocomputers.com>
Tested-by: Juno Computers USA <usa@junocomputers.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230613094346.162551-1-hdegoede@redhat.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Replace timestamping by the new common inv_sensors timestamp
module. The principle behind is the same but the implementation in
the new module is far better providing less jitter and a better
estimation.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-5-inv.git-commit@tdk.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Rename common module to inv_sensors_timestamp, add configuration
at init (chip internal clock, acceptable jitter, ...) and update
inv_icm42600 driver integration.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-4-inv.git-commit@tdk.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Create new inv_sensors common modules and move inv_icm42600
timestamp module inside. This module will be used by IMUs and
also in the future by other chips.

Modify inv_icm42600 driver to use timestamp module and do some
headers cleanup.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-3-inv.git-commit@tdk.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Move icm42600 dependent function inside the core module.
Do some headers cleanup at the same time.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-2-inv.git-commit@tdk.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Print read and expected device ID as debug warning.
Add error check for ad_sd_init() result.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Markus Burri <markus.burri@mt.com>
Link: https://lore.kernel.org/r/20230614073033.2497318-1-markus.burri@mt.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

If st->mclk is not NULL, then st->clock_sel is either AD7192_CLK_EXT_MCLK2
or AD7192_CLK_EXT_MCLK1_2.

So devm_clk_get_optional_enabled() can be used instead of hand writing it.
This saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/7dbe973905f1fdae5d2f5ae5a3b01dd1d6a9925b.1686774340.git.christophe.jaillet@wanadoo.frSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Reference iio.yaml schema from dtschema to allow already used
label property:

  sc7180-trogdor-pazquel360-lte.dtb: proximity@28: 'label' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230617103658.114453-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Reference iio.yaml schema from dtschema to allow already used
label property:

  sc7180-trogdor-homestar-r4.dtb: proximity@28: 'label' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230617103658.114453-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.

The answer is "No. No we cannot".

I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street.  And at the yearly
maintainer summit, we will all sing the alphabet song together.

I doubt I will keep doing this.  At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.

Repeats: 80e62bc8 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull dma-mapping fixes from Christoph Hellwig:

 - swiotlb area sizing fixes (Petr Tesarik)

* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: reduce the number of areas to match actual memory pool size
  swiotlb: always set the number of areas before allocating the pool

Pull irq update from Borislav Petkov:

 - Optimize IRQ domain's name assignment

* tag 'irq_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqdomain: Use return value of strreplace()

Pull x86 fpu fix from Borislav Petkov:

 - Do FPU AP initialization on Xen PV too which got missed by the recent
   boot reordering work

* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/xen: Fix secondary processors' FPU initialization

Pull x86 fix from Thomas Gleixner:
 "A single fix for the mechanism to park CPUs with an INIT IPI.

  On shutdown or kexec, the kernel tries to park the non-boot CPUs with
  an INIT IPI. But the same code path is also used by the crash utility.
  If the CPU which panics is not the boot CPU then it sends an INIT IPI
  to the boot CPU which resets the machine.

  Prevent this by validating that the CPU which runs the stop mechanism
  is the boot CPU. If not, leave the other CPUs in HLT"

* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smp: Don't send INIT to boot CPU

Pull MIPS fixes from Thomas Bogendoerfer:

 - fixes for KVM

 - fix for loongson build and cpu probing

 - DT fixes

* tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
  MIPS: dts: add missing space before {
  MIPS: Loongson: Fix build error when make modules_install
  MIPS: KVM: Fix NULL pointer dereference
  MIPS: Loongson: Fix cpu_probe_loongson() again

Pull xfs fix from Darrick Wong:
 "Nothing exciting here, just getting rid of a gcc warning that I got
  tired of seeing when I turn on gcov"

* tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix uninit warning in xfs_growfs_data

Pull more smb client updates from Steve French:

 - fix potential use after free in unmount

 - minor cleanup

 - add worker to cleanup stale directory leases

* tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Add a laundromat thread for cached directories
  smb: client: remove redundant pointer 'server'
  cifs: fix session state transition to avoid use-after-free issue