Currently, there's no good way to test for the presence of
set_memory_ro/rw/x/nx() helpers implemented by archs such as
x86, arm, arm64 and s390.

There's DEBUG_SET_MODULE_RONX and DEBUG_RODATA, however both
don't really reflect that: set_memory_*() are also available
even when DEBUG_SET_MODULE_RONX is turned off, and DEBUG_RODATA
is set by parisc, but doesn't implement above functions. Thus,
add ARCH_HAS_SET_MEMORY that is selected by mentioned archs,
where generic code can test against this.

This also allows later on to move DEBUG_SET_MODULE_RONX out of
the arch specific Kconfig to define it only once depending on
ARCH_HAS_SET_MEMORY.
Suggested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

hrtimer handlers run with masked hard IRQ, we can therefore
use napi_schedule_irqoff()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit e70ac171.

jtcp_rcv_established() is in fact called with hard irq being disabled.

Initial bug report from Ricardo Nabinger Sanchez [1] still needs
to be investigated, but does not look like a TCP bug.

[1] https://www.spinics.net/lists/netdev/msg420960.htmlSigned-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Cc: Ricardo Nabinger Sanchez <rnsanchez@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use eth_hw_addr_random() to set a random MAC address in order to make sure
dev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thomas Petazzoni says:

====================
net: mvpp2: misc improvements and preparation patches

This series contains a number of fixes, misc improvements and
preparation patches for an upcoming series that adds support for the
new PPv2.2 network controller to the mvpp2 driver.

The most significant improvements are:

 - Switching to using build_skb(), which is necessary for the upcoming
   PPv2.2 support, but anyway a good improvement to the current mvpp2
   driver (supporting PPv2.1).

 - Making the driver build on 64-bit platforms.

Changes since v3:

 - Addition of a patch "net: mvpp2: fix DMA address calculation in
   mvpp2_txq_inc_put()", which fixes a bug in the driver in the
   calculation of DMA addresses. This bug was found using
   DMA_API_DEBUG.

 - Modify the "net: mvpp2: switch to build_skb() in the RX path" patch
   to recalculate the fragment size when the MTU is changed in
   mvpp2_bm_update_mtu().

 - Added Acked-by from Russell King on all patches, except:

    * "net: mvpp2: fix DMA address calculation in
      mvpp2_txq_inc_put()", because it's a new patch

    * "net: mvpp2: switch to build_skb() in the RX path" because I
      modified it since the v3.

 - Rebased on top of 4.10.

Changes since v2:

 - Fix remaining 64-bit build warning, reported by David Miller.

 - Adjust how bit mask related definitions are done in "net: mvpp2:
   simplify MVPP2_PRS_RI_* definitions" according to Russell King
   suggestions.

 - Add a patch "net: mvpp2: remove useless arguments in
   mvpp2_rx_{pkts,time}_coal_set", suggested by Russell King.

 - Rework mvpp2_rx_time_coal_set() implementation to avoid overflows
   and rounding errors. I've used the implementation suggested by
   Russell King.

Changes since v1:

 - This series is split as a separate series from the larger patch set
   adding support for PPv2.2 in the mvpp2 driver, as requested by
   David Miller.

 - Rebased on top of v4.10-rc1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The mvpp2 is going to be extended to support the Marvell Armada 7K/8K
platform, which is ARM64. As a preparation to this work, this commit
enables building the mvpp2 driver on ARM64, by:

 - Adjusting the Kconfig dependency

 - Fixing the types used in the driver so that they are 32/64-bits
   compliant. We use dma_addr_t for DMA addresses, and unsigned long
   for virtual addresses.

It is worth mentioning that after this commit, the driver is for now
still only used on 32-bits platforms, and will only work on 32-bits
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit adapts the mvpp2 RX path to use the build_skb() method. Not
only build_skb() is now the recommended mechanism, but it also
simplifies the addition of support for the PPv2.2 variant.

Indeed, without build_skb(), we have to keep track for each RX
descriptor of the physical address of the packet buffer, and the virtual
address of the SKB. However, in PPv2.2 running on 64 bits platform,
there is not enough space in the descriptor to store the virtual address
of the SKB. So having to take care only of the address of the packet
buffer, and building the SKB upon reception helps in supporting PPv2.2.

The implementation is fairly straightforward:

 - mvpp2_skb_alloc() is renamed to mvpp2_buf_alloc() and no longer
   allocates a SKB. Instead, it allocates a buffer using the new
   mvpp2_frag_alloc() function, with enough space for the data and SKB.

 - The initialization of the RX buffers in mvpp2_bm_bufs_add() as well
   as the refill of the RX buffers in mvpp2_rx_refill() is adjusted
   accordingly.

 - Finally, the mvpp2_rx() is modified to use build_skb().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of the MVPP2_PRS_RI_* definitions use the ~(value) syntax, which
doesn't compile nicely on 64-bit. Moreover, those definitions are in
fact unneeded, since they are always used in combination with a bit
mask that ensures only the appropriate bits are modified.

Therefore, such definitions should just be set to 0x0. In addition, as
suggested by Russell King, we change the _MASK definitions to also use
the BIT() macro so that it is clear they are related to the values
defined afterwards.

For example:

 #define MVPP2_PRS_RI_L2_CAST_MASK              0x600
 #define MVPP2_PRS_RI_L2_UCAST                  ~(BIT(9) | BIT(10))
 #define MVPP2_PRS_RI_L2_MCAST                  BIT(9)
 #define MVPP2_PRS_RI_L2_BCAST                  BIT(10)

becomes

 #define MVPP2_PRS_RI_L2_CAST_MASK              (BIT(9) | BIT(10))
 #define MVPP2_PRS_RI_L2_UCAST                  0x0
 #define MVPP2_PRS_RI_L2_MCAST                  BIT(9)
 #define MVPP2_PRS_RI_L2_BCAST                  BIT(10)

Because the values (MVPP2_PRS_RI_L2_UCAST, MVPP2_PRS_RI_L2_MCAST and
MVPP2_PRS_RI_L2_BCAST) are always applied with
MVPP2_PRS_RI_L2_CAST_MASK, and therefore there is no need for
MVPP2_PRS_RI_L2_UCAST to be defined as ~(BIT(9) | BIT(10)).

It fixes the following warnings when building the driver on a 64-bit
platform (which is not possible as of this commit, but will be enabled
in a follow-up commit):

drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_prs_mac_promisc_set’:
drivers/net/ethernet/marvell/mvpp2.c:524:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
 #define MVPP2_PRS_RI_L2_UCAST   ~(BIT(9) | BIT(10))
                                 ^
drivers/net/ethernet/marvell/mvpp2.c:1459:33: note: in expansion of macro ‘MVPP2_PRS_RI_L2_UCAST’
   mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L2_UCAST,
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mvpp2_bm_bufs_add() currently creates a fake cookie by calling
mvpp2_bm_cookie_pool_set(), just to be able to call
mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract
the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID.

Instead of doing this convoluted thing, just call mvpp2_bm_pool_put()
directly, since we have the BM pool ID.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit drops dead code from the mvpp2 driver. The 'in_use' and
'in_use_thresh' fields of 'struct mvpp2_bm_pool' are
incremented/decremented/initialized in various places. But they are only
used in one place:

       if (is_recycle &&
           (atomic_read(&bm_pool->in_use) < bm_pool->in_use_thresh))
               return 0;

However 'is_recycle', passed as argument to mvpp2_rx_refill() is always
false. So in fact, this code is never reached, and the 'is_recycle'
argument is useless. So let's drop this code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit remove a field of 'struct mvpp2_tx_queue' that is not used
anywhere.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mvpp2_txq_bufs_free() function is called upon TX completion to DMA
unmap TX buffers, and free the corresponding SKBs. It gets the
references to the SKB to free and the DMA buffer to unmap from a per-CPU
txq_pcpu data structure.

However, the code currently increments the pointer to the next entry
before doing the DMA unmap and freeing the SKB. It does not cause any
visible problem because for a given SKB the TX completion is guaranteed
to take place on the CPU where the TX was started. However, it is much
more logical to increment the pointer to the next entry once the current
entry has been completely unmapped/released.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configuring the MVPP2_ISR_RX_THRESHOLD_REG with the RX coalescing
time threshold, we do not check for the maximum allowed value supported
by the driver, which means we might overflow and use a bogus value. This
commit adds a check for this situation, and if a value higher than what
is supported by the hardware is provided, then we use the maximum value
supported by the hardware.

In order to achieve this in a way that avoids overflow and rounding
errors, we introduce two utility functions mvpp2_usec_to_cycles() and
cycles_to_usec(). Many thanks to Russell King for suggesting this
implementation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, mvpp2_rx_pkts_coal_set() does the following to avoid setting
a too large value for the RX coalescing by packet number:

  val = (pkts & MVPP2_OCCUPIED_THRESH_MASK);

This means that if you set a value that is slightly higher the the
maximum number of packets, you in fact get a very low value. It makes a
lot more sense to simply check if the value is too high, and if it's too
high, limit it to the maximum possible value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

As noticed by Russell King, the last argument of
mvpp2_rx_{pkts,time}_coal_set() is useless, since the packet/time
coalescing value is already stored in the 'struct mvpp2_rx_queue *'
passed as argument to these functions. So passing the packet/time value
as an additional argument, and setting them again in the mvpp2_rx_queue
structure is useles.

This commit therefore gets rid of this additional argument, assuming the
caller has assigned the appropriate value to rxq->pkts_coal or
rxq->time_coal before calling the respective functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

When TX descriptors are filled in, the buffer DMA address is split
between the tx_desc->buf_phys_addr field (high-order bits) and
tx_desc->packet_offset field (5 low-order bits).

However, when we re-calculate the DMA address from the TX descriptor in
mvpp2_txq_inc_put(), we do not take tx_desc->packet_offset into
account. This means that when the DMA address is not aligned on a 32
bytes boundary, we end up calling dma_unmap_single() with a DMA address
that was not the one returned by dma_map_single().

This inconsistency is detected by the kernel when DMA_API_DEBUG is
enabled. We fix this problem by properly calculating the DMA address in
mvpp2_txq_inc_put().

Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MACSec test failed when asynchronous crypto operations is used. It
encounters packet validation failed since macsec_skb_cb(skb)->valid
is always 'false'.

This patch adds missing "macsec_skb_cb(skb)->valid = true" in
macsec_decrypt_done() when "err == 0".
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The USEC_PER_SEC is used once in sock_set_timeout as the max value of
tv_usec. But there are other similar codes which use the literal
1000000 in this file.
It is minor cleanup to keep consitent.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch switch to use build_skb() for small buffer which can have
better performance for both TCP and XDP (since we can work at page
before skb creation). It also remove lots of XDP codes since both
mergeable and small buffer use page frag during refill now.

                       Before   | After
XDP_DROP(xdp1) 64B  :  11.1Mpps | 14.4Mpps

Tested with xdp1/xdp2/xdp_ip_tx_tunnel and netperf.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skbs processed by ip_cmsg_recv() are not guaranteed to
be linear e.g. when sending UDP packets over loopback with
MSGMORE.
Using csum_partial() on [potentially] the whole skb len
is dangerous; instead be on the safe side and use skb_checksum().

Thanks to syzkaller team to detect the issue and provide the
reproducer.

v1 -> v2:
 - move the variable declaration in a tighter scope

Fixes: ad6f939a ("ip: Add offset parameter to ip_cmsg_recv")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

silences the below warning:
    drivers/net/vxlan.c: In function ‘neigh_reduce’:
    drivers/net/vxlan.c:1599:25: warning: variable ‘saddr’ set but not used
    [-Wunused-but-set-variable]
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds changelink rtnl op support for vxlan netdevs.
code changes involve:
    - refactor vxlan_newlink into vxlan_nl2conf to be
    used by vxlan_newlink and vxlan_changelink
    - vxlan_nl2conf and vxlan_dev_configure take a
    changelink argument to isolate changelink checks
    and updates.
    - Allow changing only a few attributes:
        - return -EOPNOTSUPP for attributes that cannot
        be changed for now. Incremental patches can
        make the non-supported one available in the future
        if needed.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is only one possible error path which reaches the err label, so
return ERR_PTR(-ENOMEM) directly if alloc_netdev_mqs() fails. This also
allows to omit the err variable.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

We set queues before reset which will cause a crash[1]. This is
because is_xdp_raw_buffer_queue() depends on the old xdp queue pairs
number to do the correct detection. So fix this by

- passing xdp queue pairs and current queue pairs to virtnet_reset()
- change vi->xdp_qp after reset but before refill, to make sure both
  free_unused_bufs() and refill can make correct detection of XDP.
- remove the duplicated queue pairs setting before virtnet_reset()
  since we will do it inside virtnet_reset()

[1]

[   74.328168] general protection fault: 0000 [#1] SMP
[   74.328625] Modules linked in: nfsd xfs libcrc32c virtio_net virtio_pci
[   74.329117] CPU: 0 PID: 2849 Comm: xdp2 Not tainted 4.10.0-rc7+ #499
[   74.329577] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.1-0-g8891697-prebuilt.qemu-project.org 04/01/2014
[   74.330424] task: ffff88007a894000 task.stack: ffffc90004388000
[   74.330844] RIP: 0010:skb_release_head_state+0x28/0x80
[   74.331298] RSP: 0018:ffffc9000438b8d0 EFLAGS: 00010206
[   74.331676] RAX: 0000000000000000 RBX: ffff88007ad96300 RCX: 0000000000000000
[   74.332217] RDX: ffff88007fc137a8 RSI: ffff88007fc0db28 RDI: 0001bf00000001be
[   74.332758] RBP: ffffc9000438b8d8 R08: 000000000005008f R09: 00000000000005f9
[   74.333274] R10: ffff88007d001700 R11: ffffffff820a8a4d R12: ffff88007ad96300
[   74.333787] R13: 0000000000000002 R14: ffff880036604000 R15: 000077ff80000000
[   74.334308] FS:  00007fc70d8a7b40(0000) GS:ffff88007fc00000(0000) knlGS:0000000000000000
[   74.334891] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   74.335314] CR2: 00007fff4144a710 CR3: 000000007ab56000 CR4: 00000000003406f0
[   74.335830] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   74.336373] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   74.336895] Call Trace:
[   74.337086]  skb_release_all+0xd/0x30
[   74.337356]  consume_skb+0x2c/0x90
[   74.337607]  free_unused_bufs+0x1ff/0x270 [virtio_net]
[   74.337988]  ? vp_synchronize_vectors+0x3b/0x60 [virtio_pci]
[   74.338398]  virtnet_xdp+0x21e/0x440 [virtio_net]
[   74.338741]  dev_change_xdp_fd+0x101/0x140
[   74.339048]  do_setlink+0xcf4/0xd20
[   74.339304]  ? symcmp+0xf/0x20
[   74.339529]  ? mls_level_isvalid+0x52/0x60
[   74.339828]  ? mls_range_isvalid+0x43/0x50
[   74.340135]  ? nla_parse+0xa0/0x100
[   74.340400]  rtnl_setlink+0xd4/0x120
[   74.340664]  ? cpumask_next_and+0x30/0x50
[   74.340966]  rtnetlink_rcv_msg+0x7f/0x1f0
[   74.341259]  ? sock_has_perm+0x59/0x60
[   74.341586]  ? napi_consume_skb+0xe2/0x100
[   74.342010]  ? rtnl_newlink+0x890/0x890
[   74.342435]  netlink_rcv_skb+0x92/0xb0
[   74.342846]  rtnetlink_rcv+0x23/0x30
[   74.343277]  netlink_unicast+0x162/0x210
[   74.343677]  netlink_sendmsg+0x2db/0x390
[   74.343968]  sock_sendmsg+0x33/0x40
[   74.344233]  SYSC_sendto+0xee/0x160
[   74.344482]  ? SYSC_bind+0xb0/0xe0
[   74.344806]  ? sock_alloc_file+0x92/0x110
[   74.345106]  ? fd_install+0x20/0x30
[   74.345360]  ? sock_map_fd+0x3f/0x60
[   74.345586]  SyS_sendto+0x9/0x10
[   74.345790]  entry_SYSCALL_64_fastpath+0x1a/0xa9
[   74.346086] RIP: 0033:0x7fc70d1b8f6d
[   74.346312] RSP: 002b:00007fff4144a708 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[   74.346785] RAX: ffffffffffffffda RBX: 00000000ffffffff RCX: 00007fc70d1b8f6d
[   74.347244] RDX: 000000000000002c RSI: 00007fff4144a720 RDI: 0000000000000003
[   74.347683] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000
[   74.348544] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff4144bd90
[   74.349082] R13: 0000000000000002 R14: 0000000000000002 R15: 00007fff4144cda0
[   74.349607] Code: 00 00 00 55 48 89 e5 53 48 89 fb 48 8b 7f 58 48 85 ff 74 0e 40 f6 c7 01 74 3d 48 c7 43 58 00 00 00 00 48 8b 7b 68 48 85 ff 74 05 <f0> ff 0f 74 20 48 8b 43 60 48 85 c0 74 14 65 8b 15 f3 ab 8d 7e
[   74.351008] RIP: skb_release_head_state+0x28/0x80 RSP: ffffc9000438b8d0
[   74.351625] ---[ end trace fe6e19fd11cfc80b ]---

Fixes: 2de2f7f4 ("virtio_net: XDP support for adjust_head")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit adds the ndo_do_ioctl() callback which allows the userspace to
access PHY registers, for example. This will make mii-diag and similar
tools work.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Fix probe and open bugs.

Fix 3 issues related to bnxt_init_one() and bnxt_open().  Don't probe
bridge devices and fixup some error code paths.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the bnxt_init_one() failure path, bar1 and bar2 are not
being unmapped.  This commit fixes this issue.  Reorganize the
code so that bnxt_init_one()'s failure path and bnxt_remove_one()
can call the same function to do the PCI cleanup.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If bnxt_hwrm_ring_free() is called during a failure path in bnxt_open(),
it is possible that the completion rings have not been allocated yet.
In that case, the completion doorbell has not been initialized, and
calling bnxt_disable_int() will crash.  Fix it by checking that the
completion ring has been initialized before writing to the completion
ring doorbell.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are additional SoC devices that use the same device ID for
bridge and NIC devices.  The bnxt driver should reject probe against
all bridge devices since it's meant to be used with only endpoint
devices.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed*: Bug fixes

This is a respin of the series with same name for net-next
instead of net [only patch #10 is changed].

The 3 first patches here are a repost of
("qed: RoCE infrastructure fixes"). The fourth is an additional
RoCE-related infrastructure fix, and the latter contain various fixes
to qed/qede.

Please consider applying these to `net-next'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver changes the link properties via communication with
the management firmware, and re-reads the resulting link status
when it receives an indication that the link has changed.
However, there are certain scenarios where such indications
might be missing, and so driver also re-reads the current link
results without attention in several places. Specifically, it
does so during load and when resetting the link.

This creates a race where driver might reflect incorrect
link status - e.g., when explicit reading of the link status is
switched by attention with the changed configuration.

Correct this flow by a lock syncronizing the handling of the
link indications [both explicit requests and attention].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flows accessing registers require the flow to hold a PTT entry.
To protect 'major' load/unload flows a main_ptt is pre-allocated
to guarantee such flows wouldn't be blocked by PTT being
unavailable.

Status block initialization currently uses the main_ptt which
is incorrect, as this flow might run concurrently to others
[E.g., loading qedr while toggling qede]. That would have dire
effects as it means registers' access to device breaks and further
read/writes might access incorrect addresses.

Instead, when initializing status blocks acquire/release a PTT
as part of the flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver currently utilizes the same loop variable in two
nested loops.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VF learns of the current link state via its bulletin board,
which might reflect either the physical link state or some
user-configured logical state.
Whenever the physical link changes or whnever such a configuration
is explicitly made by user the PF driver would update the bulletin
that the VF reads. But if neither has happened - i.e., PF still
hasn't got a physical link up and no additional configuration was
done the VF wouldn't have a valid link information available.

Simply reflect the physical link state whenever the VF is
initialized. The user could then affect it however he wants.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed needs to be informed of the removal of the qede interface
prior to its actual removal, as qede has some registered callbacks
that might get called async to the removal flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Need to make sure the slowpath workqueue and the qede lock
are ready for the registration of the netdevice, as once
registered there's no guarantee those wouldn't be used.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reserving doorbell BAR space according to the currently active CPUs
may result in a bug if disabled CPUs are later enabled but no
doorbell space was reserved for them.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>