Straighten out the clamp control configurations for the various video modes,
based off of register diffs done against the Hauppauge Windows driver.

This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Cleanup the routine which disables the audio decoder.  In particular, the i2s
output was being shut off but the audio processor itself was not, resulting
in more power being consumed than needed.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Fix the alignment of fields being delivered by the driver, which was
resulting in jerky video when there was horizontal motion (since the bottom
field of the frame was being sent with the top field of the previous frame)

This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

We had the max packets per URB set to an incredibly low "10" as opposed to
the Windows driver which has it as 128.  Set the value to match the
Windows driver, which will reduce interrupts considerably.

This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The chip's default value for the brightness didn't match what we were sending
back in the queryctrl ioctl(), so if the application actually set the
brightness to the "default", it would actually end up being way too bright.

This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The bad value prevented the autogain to work correctly
and some images were truncated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Generate a release button event when the button is still pressed when the
stream stops.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

gspca_xirlink_cit: Add support camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

At least on the ibm netcam pro frames have a 4 byte footer, take this
into account when calculating sizeimage.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The following usb bandwidth allocation changes were made to the ibm netcam
pro code:
- Don't restart negotiation at max packet size on stop0, as that gets called
  by gspca_main during negotiation. Move this to sd_isoc_init.
- Don't ask for full bandwidth when running at 160x120, that does not need
  full bandwidth
- Make minimum acceptable bandwidth depend upon resolution

[mchehab@redhat.com: Fix CodingStyle problems at switch statements]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Currently alloc_and_submit_int_urb() is setting gspca->int_urb
as soon as the allocation has succeeded, but if the subsequent
submit fails, the urb gets destroyed. And then later will
get destroyed again in gspca_input_destroy_urb() because
gspca->int_urb is set, leading to a double free.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Currently gspca supported usb-1.1 webcams for which we support the input
button through an interrupt endpoint won't stream (not enough bandwidth
error) when used through an USB-2.0 hub.

After much debugging I've found out that the cause for this is that the
ehci-sched.c schedeling code does not like it when there are already urb's
scheduled when (large) isoc urbs are queued. By moving the submission
of the interrupt urbs to after submitting the isoc urbs the camera
starts working again through usb-2.0 hubs.

Note that this does not fix isoc. streaming through a usb-hub while another
1.1 usb device (like the microphone of the same cam) is also active
at the same time :(

I've spend a long time analyzing the linux kernel ehci scheduler code,
resulting in this (long) mail:
http://www.spinics.net/lists/linux-usb/msg37982.html

The conclusion of the following mail thread is that yes there are several
issues when using usb-1.1 devices through a usb-2.0 hub, but these are not
easily fixable in the current code. Fixing this in ehci-sched.c requires
an almost full rewrite, which is not bound to happen anytime soon.

So with this patch gspca driven usb-1.1 webcams will atleast work when
connected through an usb-2.0 hub when the microphone is not used.

As an added bonus this patch avoids extra destroy/create input urb cycles
when we end up falling back to a lower speed alt setting because of bandwidth
limitations.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

DM04/QQBOX USB Timing change.

Improved timing to avoid USB corruptions on some systems.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Corrected Firmware Information for LG on LME2510.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Improved frontend handling.

Frontend now remains open at all times, with signal lock, snr & signal level
polled from Interupt.

Updated driver for DM04/QQBOX USB DVB-S BOXES to version 1.70.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

If you suspend and resume during video capture, the video colours
are corrupted on resume. This is because the sensor is being unconditionally
powered off during the resume path.

Only power down during resume if the camera is not in use, and correctly
reconfigure the sensor during resume.
Fixes http://dev.laptop.org/ticket/10190Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Converted if (debug >= 2) printk(KERN_DEBUG... to if debug >= 2) dprintk(...)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Although cx231xx has a very good IR support, already supported by
mceusb driver, some designs decided to add a separate I2C
microcontroller chip in order to handle IR.

Due to that, add a glue to ir-kbd-i2c is needed, in order to support
those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

By comparing the traffic between Pixelview (cx23102-based and Kworld
(saa7134-based), the only difference is at register 0xd5. After some
tests, It seems that it is used to change mode between serial and parallel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This adds the trivial bits to mb86a20s. As the driver won't touch
at the channel/layer parameters, this may not be enough for
receiving all channels, especially ISDB-Tsb, but the driver worked
properly for receiving video channels on my tests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This device uses an em2874B + Sharp 921 One Seg frontend.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

On our tests with Leadership ISDBT, the s921 frontend were not work. As its
design contained some weird things, it ended to be easier to just re-write
it, getting another frontend as an example (cx24123).

As the old s921 driver weren't used, there's no regression. Some info from
the old frontend were used as a way to double check the behavior that were
noticed on the USB dumps retrieved from Leadership driver.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  ring_buffer: Off-by-one and duplicate events in ring_buffer_read_page

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86/microcode: Fix double vfree() and remove redundant pointer checks before vfree()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI hotplug: Fix unexpected driver unregister in pciehp_acpi.c

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] v4l: soc-camera: fix multiple simultaneous user case

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: Fix re-probing with PM_POST_RESTORE notification
  mmc: atmel-mci: fix multiblock SDIO transfers
  mmc: at91_mci: fix multiblock SDIO transfers

arm: export dma_set_coherent_mask

While a regression was fixed with commit 710224fa (arm: fix
"arm: fix pci_set_consistent_dma_mask for dmabounce devices"), a
new one was introduced as dma_set_coherent_mask wasn't exported
for modules. This patch takes care for this issue.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The current code mis-calculates the ramoops header size, leading to an
overflow over the next record at best, or over a non-allocated region at
worst.  Fix that calculation.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Marco Stornelli <marco.stornelli@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>