- 26 Jul, 2019 40 commits
-
-
Emmanuel Grumbach authored
commit ed3e4c6d upstream. Newest devices have a new firmware load mechanism. This mechanism is called the context info. It means that the driver doesn't need to load the sections of the firmware. The driver rather prepares a place in DRAM, with pointers to the relevant sections of the firmware, and the firmware loads itself. At the end of the process, the firmware sends the ALIVE interrupt. This is different from the previous scheme in which the driver expected the FH_TX interrupt after each section being transferred over the DMA. In order to support this new flow, we enabled all the interrupts. This broke the assumption that we have in the code that the RF-Kill interrupt can't interrupt the firmware load flow. Change the context info flow to enable only the ALIVE interrupt, and re-enable all the other interrupts only after the firmware is alive. Then, we won't see the RF-Kill interrupt until then. Getting the RF-Kill interrupt while loading the firmware made us kill the firmware while it is loading and we ended up dumping garbage instead of the firmware state. Re-enable the ALIVE | RX interrupts from the ISR when we get the ALIVE interrupt to be able to get the RX interrupt that comes immediately afterwards for the ALIVE notification. This is needed for non MSI-X only. Cc: stable@vger.kernel.org Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Emmanuel Grumbach authored
commit 0d53cfd0 upstream. iwl_mvm_send_cmd returns 0 when the command won't be sent because RF-Kill is asserted. Do the same when we call iwl_get_shared_mem_conf since it is not sent through iwl_mvm_send_cmd but directly calls the transport layer. Cc: stable@vger.kernel.org Signed-off-by:
-
Emmanuel Grumbach authored
commit ec46ae30 upstream. We added code to restock the buffer upon ALIVE interrupt when MSI-X is disabled. This was added as part of the context info code. This code was added only if the ISR debug level is set which is very unlikely to be related. Move this code to run even when the ISR debug level is not set. Note that gen2 devices work with MSI-X in most cases so that this path is seldom used. Cc: stable@vger.kernel.org Signed-off-by:
-
Emmanuel Grumbach authored
commit 3b57a10c upstream. Sometimes the register status can include interrupts that were masked. We can, for example, get the RF-Kill bit set in the interrupt status register although this interrupt was masked. Then if we get the ALIVE interrupt (for example) that was not masked, we need to *not* service the RF-Kill interrupt. Fix this in the MSI-X interrupt handler. Cc: stable@vger.kernel.org Signed-off-by:
-
Oren Givon authored
commit 498d3eb5 upstream. The 22000 series FW that was meant to be used with hr is also the FW that is used for hr1 and has a different RF ID. Add support to load the hr FW when hr1 RF ID is detected. Cc: stable@vger.kernel.org # 5.1+ Signed-off-by:
Oren Givon <oren.givon@intel.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Jon Hunter authored
commit ece6031e upstream. The GPU regulator enable ramp delay for Jetson TX1 is set to 1ms which not sufficient because the enable ramp delay has been measured to be greater than 1ms. Furthermore, the downstream kernels released by NVIDIA for Jetson TX1 are using a enable ramp delay 2ms and a settling delay of 160us. Update the GPU regulator enable ramp delay for Jetson TX1 to be 2ms and add a settling delay of 160us. Cc: stable@vger.kernel.org Signed-off-by:
Jon Hunter <jonathanh@nvidia.com> Fixes: 5e6b9a89 ("arm64: tegra: Add VDD_GPU regulator to Jetson TX1") Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 16da0eb5 upstream. On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750 mV, not 600 mV. Using wrong minimal value caused shifting of these regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was reported as 1.2 V). On most of the boards these regulators are left in default state so this was only affecting reported voltage. However if any driver wanted to change them, then effectively it would set voltage 150 mV higher than intended. Cc: <stable@vger.kernel.org> Fixes: cb74685e ("regulator: s2mps11: Add samsung s2mps11 regulator driver") Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 70ca117b upstream. If devm_gpiod_get_from_of_node() call returns ERR_PTR, it is assigned into an array of GPIO descriptors and used later because such error is not treated as critical thus it is not propagated back to the probe function. All code later expects that such GPIO descriptor is either a NULL or proper value. This later might lead to dereference of ERR_PTR. Only devices with S2MPS14 flavor are affected (other do not control regulators with GPIOs). Fixes: 1c984942 ("regulator: s2mps11: Pass descriptor instead of GPIO number") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Hui Wang authored
commit 771a081e upstream. In the function alps_is_cs19_trackpoint(), we check if the param[1] is in the 0x20~0x2f range, but the code we wrote for this checking is not correct: (param[1] & 0x20) does not mean param[1] is in the range of 0x20~0x2f, it also means the param[1] is in the range of 0x30~0x3f, 0x60~0x6f... Now fix it with a new condition checking ((param[1] & 0xf0) == 0x20). Fixes: 7e4935cc ("Input: alps - don't handle ALPS cs19 trackpoint-only device") Cc: stable@vger.kernel.org Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Nick Black authored
commit 1976d7d2 upstream. Adds the Lenovo T580 to the SMBus intertouch list for Synaptics touchpads. I've tested with this for a week now, and it seems a great improvement. It's also nice to have the complaint gone from dmesg. Signed-off-by:
Nick Black <dankamongmen@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Hui Wang authored
commit 7e4935cc upstream. On a latest Lenovo laptop, the trackpoint and 3 buttons below it don't work at all, when we move the trackpoint or press those 3 buttons, the kernel will print out: "Rejected trackstick packet from non DualPoint device" This device is identified as an alps touchpad but the packet has trackpoint format, so the alps.c drops the packet and prints out the message above. According to XiaoXiao's explanation, this device is named cs19 and is trackpoint-only device, its firmware is only for trackpoint, it is independent of touchpad and is a device completely different from DualPoint ones. To drive this device with mininal changes to the existing driver, we just let the alps driver not handle this device, then the trackpoint.c will be the driver of this device if the trackpoint driver is enabled. (if not, this device will fallback to a bare PS/2 device) With the trackpoint.c, this trackpoint and 3 buttons all work well, they have all features that the trackpoint should have, like scrolling-screen, drag-and-drop and frame-selection. Signed-off-by:
XiaoXiao Liu <sliuuxiaonxiao@gmail.com> Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Grant Hernandez authored
commit 2a017fd8 upstream. The GTCO tablet input driver configures itself from an HID report sent via USB during the initial enumeration process. Some debugging messages are generated during the parsing. A debugging message indentation counter is not bounds checked, leading to the ability for a specially crafted HID report to cause '-' and null bytes be written past the end of the indentation array. As long as the kernel has CONFIG_DYNAMIC_DEBUG enabled, this code will not be optimized out. This was discovered during code review after a previous syzkaller bug was found in this driver. Signed-off-by:
Grant Hernandez <granthernandez@google.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Coly Li authored
commit f54d801d upstream. Commit 9baf3097 ("bcache: fix for gc and write-back race") added a new work queue dc->writeback_write_wq, but forgot to destroy it in the error condition when creating dc->writeback_thread failed. This patch destroys dc->writeback_write_wq if kthread_create() returns error pointer to dc->writeback_thread, then a memory leak is avoided. Fixes: 9baf3097 ("bcache: fix for gc and write-back race") Signed-off-by:
Coly Li <colyli@suse.de> Cc: stable@vger.kernel.org Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Coly Li authored
commit 54619998 upstream. In bch_cached_dev_files[] from driver/md/bcache/sysfs.c, sysfs_errors is incorrectly inserted in. The correct entry should be sysfs_io_errors. This patch fixes the problem and now I/O errors of cached device can be read from /sys/block/bcache<N>/bcache/io_errors. Fixes: c7b7bd07 ("bcache: add io_disable to struct cached_dev") Signed-off-by:
-
Coly Li authored
commit 578df99b upstream. When md raid device (e.g. raid456) is used as backing device, read-ahead requests on a degrading and recovering md raid device might be failured immediately by md raid code, but indeed this md raid array can still be read or write for normal I/O requests. Therefore such failed read-ahead request are not real hardware failure. Further more, after degrading and recovering accomplished, read-ahead requests will be handled by md raid array again. For such condition, I/O failures of read-ahead requests don't indicate real health status (because normal I/O still be served), they should not be counted into I/O error counter dc->io_errors. Since there is no simple way to detect whether the backing divice is a md raid device, this patch simply ignores I/O failures for read-ahead bios on backing device, to avoid bogus backing device failure on a degrading md raid array. Suggested-and-tested-by:
Thorsten Knabe <linux@thorsten-knabe.de> Signed-off-by:
-
Coly Li authored
commit ba82c1ac upstream. This reverts commit 6268dc2c. This patch depends on commit c4dc2497 ("bcache: fix high CPU occupancy during journal") which is reverted in previous patch. So revert this one too. Fixes: 6268dc2c ("bcache: free heap cache_set->flush_btree in bch_journal_free") Signed-off-by:
-
Coly Li authored
commit 249a5f6d upstream. This reverts commit c4dc2497. This patch enlarges a race between normal btree flush code path and flush_btree_write(), which causes deadlock when journal space is exhausted. Reverts this patch makes the race window from 128 btree nodes to only 1 btree nodes. Fixes: c4dc2497 ("bcache: fix high CPU occupancy during journal") Signed-off-by:
-
Coly Li authored
commit 695277f1 upstream. This reverts commit 6147305c. Although this patch helps the failed bcache device to stop faster when too many I/O errors detected on corresponding cached device, setting CACHE_SET_IO_DISABLE bit to cache set c->flags was not a good idea. This operation will disable all I/Os on cache set, which means other attached bcache devices won't work neither. Without this patch, the failed bcache device can also be stopped eventually if internal I/O accomplished (e.g. writeback). Therefore here I revert it. Fixes: 6147305c ("bcache: set CACHE_SET_IO_DISABLE in bch_cached_dev_error()") Reported-by:
Yong Li <mr.liyong@qq.com> Signed-off-by:
-
Aurelien Aptel authored
commit 7e5a70ad upstream. Prevent deadlock between open_shroot() and cifs_mark_open_files_invalid() by releasing the lock before entering SMB2_open, taking it again after and checking if we still need to use the result. Link: https://lore.kernel.org/linux-cifs/684ed01c-cbca-2716-bc28-b0a59a0f8521@prodrive-technologies.com/T/#u Fixes: 3d4ef9a1 ("smb3: fix redundant opens on root") Signed-off-by:
Aurelien Aptel <aaptel@suse.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by:
-
Ronnie Sahlberg authored
commit aa081859 upstream. Servers can defer destaging any data and updating the mtime until close(). This means that if we do a setinfo to modify the mtime while other handles are open for write the server may overwrite our setinfo timestamps when if flushes the file on close() of the writeable handle. To solve this we add an explicit flush when the mtime is about to be updated. This fixes "cp -p" to preserve mtime when copying a file onto an SMB2 share. CC: Stable <stable@vger.kernel.org> Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by:
-
Paulo Alcantara (SUSE) authored
commit 29fbeb7a upstream. Fix mount options comparison when serverino option is turned off later in cifs_autodisable_serverino() and thus avoiding mismatch of new cifs mounts. Cc: stable@vger.kernel.org Signed-off-by:
Paulo Alcantara (SUSE) <paulo@paulo.ac> Signed-off-by:
Pavel Shilovsky <pshilove@microsoft.com> Signed-off-by:
-
Ronnie Sahlberg authored
commit 88a92c91 upstream. RHBZ: 1722704 In low memory situations the various SMB2_*_init() functions can fail to allocate a request PDU and thus leave the request iovector as NULL. If we don't check the return code for failure we end up calling smb2_set_next_command() with a NULL iovector causing a crash when it tries to dereference it. CC: Stable <stable@vger.kernel.org> Signed-off-by:
-
Ronnie Sahlberg authored
commit 3e272579 upstream. not just if CONFIG_CIFS_DEBUG2 is enabled. Signed-off-by:
-
Wen Yang authored
commit 95566aa7 upstream. There is a possible double free issue in ppc4xx_trng_probe(): 85: dev->trng_base = of_iomap(trng, 0); 86: of_node_put(trng); ---> released here 87: if (!dev->trng_base) 88: goto err_out; ... 110: ierr_out: 111: of_node_put(trng); ---> double released here ... This issue was detected by using the Coccinelle software. We fix it by removing the unnecessary of_node_put(). Fixes: 5343e674 ("crypto4xx: integrate ppc4xx-rng into crypto4xx") Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Cc: <stable@vger.kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Allison Randal <allison@lohutok.net> Cc: Armijn Hemel <armijn@tjaldur.nl> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Acked-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Cfir Cohen authored
commit 538a5a07 upstream. Avoid leaking GCM tag through timing side channel. Fixes: 36cf515b ("crypto: ccp - Enable support for AES GCM on v5 CCPs") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by:
Cfir Cohen <cfir@google.com> Acked-by:
Gary R Hook <ghook@amd.com> Signed-off-by:
-
Hook, Gary authored
commit 20e833dc upstream. The AES GCM function reuses an 'op' data structure, which members contain values that must be cleared for each (re)use. This fix resolves a crypto self-test failure: alg: aead: gcm-aes-ccp encryption test failed (wrong result) on test vector 2, cfg="two even aligned splits" Fixes: 36cf515b ("crypto: ccp - Enable support for AES GCM on v5 CCPs") Cc: <stable@vger.kernel.org> Signed-off-by:
Gary R Hook <gary.hook@amd.com> Signed-off-by:
-
Christian Lamparter authored
commit 0f7a8137 upstream. The hardware automatically zero pads incomplete block ciphers blocks without raising any errors. This is a screw-up. This was noticed by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS tests that sent a incomplete blocks and expect them to fail. This fixes: cbc-aes-ppc4xx encryption unexpectedly succeeded on test vector "random: len=2409 klen=32"; expected_error=-22, cfg="random: may_sleep use_digest src_divs=[96.90%@+2295, 2.34%@+4066, 0.32%@alignmask+12, 0.34%@+4087, 0.9%@alignmask+1787, 0.1%@+3767] iv_offset=6" ecb-aes-ppc4xx encryption unexpectedly succeeded on test vector "random: len=1011 klen=32"; expected_error=-22, cfg="random: may_sleep use_digest src_divs=[100.0%@alignmask+20] dst_divs=[3.12%@+3001, 96.88%@+4070]" Cc: Eric Biggers <ebiggers@kernel.org> Cc: stable@vger.kernel.org [4.19, 5.0 and 5.1] Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Christian Lamparter authored
commit 70c4997f upstream. While the hardware consider them to be blockciphers, the reference implementation defines them as streamciphers. Do the right thing and set the blocksize to 1. This was found by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS. This fixes the following issues: skcipher: blocksize for ofb-aes-ppc4xx (16) doesn't match generic impl (1) skcipher: blocksize for cfb-aes-ppc4xx (16) doesn't match generic impl (1) Cc: Eric Biggers <ebiggers@kernel.org> Cc: stable@vger.kernel.org Fixes: f2a13e7c ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads") Signed-off-by:
-
Christian Lamparter authored
commit bfa2ba7d upstream. This patch fixes a issue with crypto4xx's ctr(aes) that was discovered by libcapi's kcapi-enc-test.sh test. The some of the ctr(aes) encryptions test were failing on the non-power-of-two test: kcapi-enc - Error: encryption failed with error 0 kcapi-enc - Error: decryption failed with error 0 [FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits): original file (1d100e..cc96184c) and generated file (e3b0c442..1b7852b855) [FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits) (openssl generated CT): original file (e3b0..5) and generated file (3..8e) [PASSED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits) (openssl generated PT) [FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (password): original file (1d1..84c) and generated file (e3b..852b855) But the 16, 32, 512, 65536 tests always worked. Thankfully, this isn't a hidden hardware problem like previously, instead this turned out to be a copy and paste issue. With this patch, all the tests are passing with and kcapi-enc-test.sh gives crypto4xx's a clean bill of health: "Number of failures: 0" :). Cc: stable@vger.kernel.org Fixes: 98e87e3d ("crypto: crypto4xx - add aes-ctr support") Fixes: f2a13e7c ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads") Signed-off-by:
-
Eric Biggers authored
commit 7545b6c2 upstream. Clear the CRYPTO_TFM_REQ_MAY_SLEEP flag when the chacha20poly1305 operation is being continued from an async completion callback, since sleeping may not be allowed in that context. This is basically the same bug that was recently fixed in the xts and lrw templates. But, it's always been broken in chacha20poly1305 too. This was found using syzkaller in combination with the updated crypto self-tests which actually test the MAY_SLEEP flag now. Reproducer: python -c 'import socket; socket.socket(socket.AF_ALG, 5, 0).bind( ("aead", "rfc7539(cryptd(chacha20-generic),poly1305-generic)"))' Kernel output: BUG: sleeping function called from invalid context at include/crypto/algapi.h:426 in_atomic(): 1, irqs_disabled(): 0, pid: 1001, name: kworker/2:2 [...] CPU: 2 PID: 1001 Comm: kworker/2:2 Not tainted 5.2.0-rc2 #5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-20181126_142135-anatol 04/01/2014 Workqueue: crypto cryptd_queue_worker Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x4d/0x6a lib/dump_stack.c:113 ___might_sleep kernel/sched/core.c:6138 [inline] ___might_sleep.cold.19+0x8e/0x9f kernel/sched/core.c:6095 crypto_yield include/crypto/algapi.h:426 [inline] crypto_hash_walk_done+0xd6/0x100 crypto/ahash.c:113 shash_ahash_update+0x41/0x60 crypto/shash.c:251 shash_async_update+0xd/0x10 crypto/shash.c:260 crypto_ahash_update include/crypto/hash.h:539 [inline] poly_setkey+0xf6/0x130 crypto/chacha20poly1305.c:337 poly_init+0x51/0x60 crypto/chacha20poly1305.c:364 async_done_continue crypto/chacha20poly1305.c:78 [inline] poly_genkey_done+0x15/0x30 crypto/chacha20poly1305.c:369 cryptd_skcipher_complete+0x29/0x70 crypto/cryptd.c:279 cryptd_skcipher_decrypt+0xcd/0x110 crypto/cryptd.c:339 cryptd_queue_worker+0x70/0xa0 crypto/cryptd.c:184 process_one_work+0x1ed/0x420 kernel/workqueue.c:2269 worker_thread+0x3e/0x3a0 kernel/workqueue.c:2415 kthread+0x11f/0x140 kernel/kthread.c:255 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352 Fixes: 71ebc4d1 ("crypto: chacha20poly1305 - Add a ChaCha20-Poly1305 AEAD construction, RFC7539") Cc: <stable@vger.kernel.org> # v4.2+ Cc: Martin Willi <martin@strongswan.org> Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
Elena Petrova authored
commit 6bd934de upstream. The sha256-ce finup implementation for ARM64 produces wrong digest for empty input (len=0). Expected: the actual digest, result: initial value of SHA internal state. The error is in sha256_ce_finup: for empty data `finalize` will be 1, so the code is relying on sha2_ce_transform to make the final round. However, in sha256_base_do_update, the block function will not be called when len == 0. Fix it by setting finalize to 0 if data is empty. Fixes: 03802f6a ("crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer") Cc: stable@vger.kernel.org Signed-off-by:
Elena Petrova <lenaptr@google.com> Reviewed-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
-
Elena Petrova authored
commit 1d4aaf16 upstream. The sha1-ce finup implementation for ARM64 produces wrong digest for empty input (len=0). Expected: da39a3ee..., result: 67452301... (initial value of SHA internal state). The error is in sha1_ce_finup: for empty data `finalize` will be 1, so the code is relying on sha1_ce_transform to make the final round. However, in sha1_base_do_update, the block function will not be called when len == 0. Fix it by setting finalize to 0 if data is empty. Fixes: 07eb54d3 ("crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer") Cc: stable@vger.kernel.org Signed-off-by:
-
Hook, Gary authored
commit 52393d61 upstream. The error code read from the queue status register is only 6 bits wide, but we need to verify its value is within range before indexing the error messages. Fixes: 81422bad ("crypto: ccp - Make syslog errors human-readable") Cc: <stable@vger.kernel.org> Reported-by:
-
Ard Biesheuvel authored
commit ed527b13 upstream. The CAAM driver currently violates an undocumented and slightly controversial requirement imposed by the crypto stack that a buffer referred to by the request structure via its virtual address may not be modified while any scatterlists passed via the same request structure are mapped for inbound DMA. This may result in errors like alg: aead: decryption failed on test 1 for gcm_base(ctr-aes-caam,ghash-generic): ret=74 alg: aead: Failed to load transform for gcm(aes): -2 on non-cache coherent systems, due to the fact that the GCM driver passes an IV buffer by virtual address which shares a cacheline with the auth_tag buffer passed via a scatterlist, resulting in corruption of the auth_tag when the IV is updated while the DMA mapping is live. Since the IV that is returned to the caller is only valid for CBC mode, and given that the in-kernel users of CBC (such as CTS) don't trigger the same issue as the GCM driver, let's just disable the output IV generation for all modes except CBC for the time being. Fixes: 854b06f7 ("crypto: caam - properly set IV after {en,de}crypt") Cc: Horia Geanta <horia.geanta@nxp.com> Cc: Iuliana Prodan <iuliana.prodan@nxp.com> Reported-by:
Sascha Hauer <s.hauer@pengutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by:
Horia Geanta <horia.geanta@nxp.com> Signed-off-by:
-
Eric Biggers authored
commit 5c6bc4df upstream. Changing ghash_mod_init() to be subsys_initcall made it start running before the alignment fault handler has been installed on ARM. In kernel builds where the keys in the ghash test vectors happened to be misaligned in the kernel image, this exposed the longstanding bug that ghash_setkey() is incorrectly casting the key buffer (which can have any alignment) to be128 for passing to gf128mul_init_4k_lle(). Fix this by memcpy()ing the key to a temporary buffer. Don't fix it by setting an alignmask on the algorithm instead because that would unnecessarily force alignment of the data too. Fixes: 2cdc6899 ("crypto: ghash - Add GHASH digest algorithm for GCM") Reported-by:
Peter Robinson <pbrobinson@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Finn Thain authored
commit 78ff751f upstream. A system bus error during a PDMA transfer can mess up the calculation of the transfer residual (the PDMA handshaking hardware lacks a byte counter). This results in data corruption. The algorithm in this patch anticipates a bus error by starting each transfer with a MOVE.B instruction. If a bus error is caught the transfer will be retried. If a bus error is caught later in the transfer (for a MOVE.W instruction) the transfer gets failed and subsequent requests for that target will use PIO instead of PDMA. This avoids the "!REQ and !ACK" error so the severity level of that message is reduced to KERN_DEBUG. Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: stable@vger.kernel.org # v4.14+ Fixes: 3a0f64bf ("mac_scsi: Fix pseudo DMA implementation") Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Reported-by:
Chris Jones <chris@martin-jones.com> Tested-by:
Stan Johnson <userm57@yahoo.com> Tested-by:
Michael Schmitz <schmitzmic@gmail.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Finn Thain authored
commit 7398cee4 upstream. Some targets introduce delays when handshaking the response to certain commands. For example, a disk may send a 96-byte response to an INQUIRY command (or a 24-byte response to a MODE SENSE command) too slowly. Apparently the first 12 or 14 bytes are handshaked okay but then the system bus error timeout is reached while transferring the next word. Since the scsi bus phase hasn't changed, the driver then sets the target borken flag to prevent further PDMA transfers. The driver also logs the warning, "switching to slow handshake". Raise the PDMA threshold to 512 bytes so that PIO transfers will be used for these commands. This default is sufficiently low that PDMA will still be used for READ and WRITE commands. The existing threshold (16 bytes) was chosen more or less at random. However, best performance requires the threshold to be as low as possible. Those systems that don't need the PIO workaround at all may benefit from mac_scsi.setup_use_pdma=1 Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.14+ Fixes: 3a0f64bf ("mac_scsi: Fix pseudo DMA implementation") Signed-off-by:
-
Shivasharan S authored
commit c8f96df5 upstream. In megasas_get_target_prop(), driver is incorrectly calculating the target ID for devices with channel 1 and 3. Due to this, firmware will either fail the command (if there is no device with the target id sent from driver) or could return the properties for a target which was not intended. Devices could end up with the wrong queue depth due to this. Fix target id calculation for channel 1 and 3. Fixes: 96188a89 ("scsi: megaraid_sas: NVME interface target prop added") Cc: stable@vger.kernel.org Signed-off-by:
Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by:
-
Benjamin Block authored
commit 106d45f3 upstream. When tracing instances where we open and close WKA ports, we also pass the request-ID of the respective FSF command. But after successfully sending the FSF command we must not use the request-object anymore, as this might result in an use-after-free (see "zfcp: fix request object use-after-free in send path causing seqno errors" ). To fix this add a new variable that caches the request-ID before sending the request. This won't change during the hand-off to the FCP channel, and so it's safe to trace this cached request-ID later, instead of using the request object. Signed-off-by:
Benjamin Block <bblock@linux.ibm.com> Fixes: d27a7cb9 ("zfcp: trace on request for open and close of WKA port") Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by:
Steffen Maier <maier@linux.ibm.com> Reviewed-by:
Jens Remus <jremus@linux.ibm.com> Signed-off-by:
-
Benjamin Block authored
commit b76becde upstream. With a recent change to our send path for FSF commands we introduced a possible use-after-free of request-objects, that might further lead to zfcp crafting bad requests, which the FCP channel correctly complains about with an error (FSF_PROT_SEQ_NUMB_ERROR). This error is then handled by an adapter-wide recovery. The following sequence illustrates the possible use-after-free: Send Path: int zfcp_fsf_open_port(struct zfcp_erp_action *erp_action) { struct zfcp_fsf_req *req; ... spin_lock_irq(&qdio->req_q_lock); // ^^^^^^^^^^^^^^^^ // protects QDIO queue during sending ... req = zfcp_fsf_req_create(qdio, FSF_QTCB_OPEN_PORT_WITH_DID, SBAL_SFLAGS0_TYPE_READ, qdio->adapter->pool.erp_req); // ^^^^^^^^^^^^^^^^^^^ // allocation of the request-object ... retval = zfcp_fsf_req_send(req); ... spin_unlock_irq(&qdio->req_q_lock); return retval; } static int zfcp_fsf_req_send(struct zfcp_fsf_req *req) { struct zfcp_adapter *adapter = req->adapter; struct zfcp_qdio *qdio = adapter->qdio; ... zfcp_reqlist_add(adapter->req_list, req); // ^^^^^^^^^^^^^^^^ // add request to our driver-internal hash-table for tracking // (protected by separate lock req_list->lock) ... if (zfcp_qdio_send(qdio, &req->qdio_req)) { // ^^^^^^^^^^^^^^ // hand-off the request to FCP channel; // the request can complete at any point now ... } /* Don't increase for unsolicited status */ if (!zfcp_fsf_req_is_status_read_buffer(req)) // ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ // possible use-after-free adapter->fsf_req_seq_no++; // ^^^^^^^^^^^^^^^^ // because of the use-after-free we might // miss this accounting, and as follow-up // this results in the FCP channel error // FSF_PROT_SEQ_NUMB_ERROR adapter->req_no++; return 0; } static inline bool zfcp_fsf_req_is_status_read_buffer(struct zfcp_fsf_req *req) { return req->qtcb == NULL; // ^^^^^^^^^ // possible use-after-free } Response Path: void zfcp_fsf_reqid_check(struct zfcp_qdio *qdio, int sbal_idx) { ... struct zfcp_fsf_req *fsf_req; ... for (idx = 0; idx < QDIO_MAX_ELEMENTS_PER_BUFFER; idx++) { ... fsf_req = zfcp_reqlist_find_rm(adapter->req_list, req_id); // ^^^^^^^^^^^^^^^^^^^^ // remove request from our driver-internal // hash-table (lock req_list->lock) ... zfcp_fsf_req_complete(fsf_req); } } static void zfcp_fsf_req_complete(struct zfcp_fsf_req *req) { ... if (likely(req->status & ZFCP_STATUS_FSFREQ_CLEANUP)) zfcp_fsf_req_free(req); // ^^^^^^^^^^^^^^^^^ // free memory for request-object else complete(&req->completion); // ^^^^^^^^ // completion notification for code-paths that wait // synchronous for the completion of the request; in // those the memory is freed separately } The result of the use-after-free only affects the send path, and can not lead to any data corruption. In case we miss the sequence-number accounting, because the memory was already re-purposed, the next FSF command will fail with said FCP channel error, and we will recover the whole adapter. This causes no additional errors, but it slows down traffic. There is a slight chance of the same thing happen again recursively after the adapter recovery, but so far this has not been seen. This was seen under z/VM, where the send path might run on a virtual CPU that gets scheduled away by z/VM, while the return path might still run, and so create the necessary timing. Running with KASAN can also slow down the kernel sufficiently to run into this user-after-free, and then see the report by KASAN. To fix this, simply pull the test for the sequence-number accounting in front of the hand-off to the FCP channel (this information doesn't change during hand-off), but leave the sequence-number accounting itself where it is. To make future regressions of the same kind less likely, add comments to all closely related code-paths. Signed-off-by:
-
