When joining IBSS a full scan should be initiated in order to search
for existing cell, unless the fixed_channel parameter was set.
A default channel to create the IBSS on if no cell was found is
provided as well.
However - a scan is initiated only on the default channel provided
regardless of whether ifibss->fixed_channel is set or not, with the
obvious result of the cell not joining existing IBSS cell that is
on another channel.

Fixes: 76bed0f4 ("mac80211: IBSS fix scan request")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The timestamp given by iwlwifi is at the beginning of the
frame over the air, at (or during) the SYNC field. Allow
such timestamps to be given to mac80211, at least (for now)
for frames with non-HT/VHT preambles.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The ieee80211_queue_stopped() expects hw queue
number but it was given raw WMM AC number instead.

This could cause frame drops and problems with
traffic in some cases - most notably if driver
doesn't map AC numbers to queue numbers 1:1 and
uses ieee80211_stop_queues() and
ieee80211_wake_queue() only without ever calling
ieee80211_wake_queues().

On ath10k it was possible to hit this problem in
the following case:

  1. wlan0 uses queue 0
     (ath10k maps queues per vif)
  2. offchannel uses queue 15
  3. queues 1-14 are unused
  4. ieee80211_stop_queues()
  5. ieee80211_wake_queue(q=0)
  6. ieee80211_wake_queue(q=15)
     (other queues are not woken up because both
      driver and mac80211 know other queues are
      unused)
  7. ieee80211_rx_h_mesh_fwding()
  8. ieee80211_select_queue_80211() returns 2
  9. ieee80211_queue_stopped(q=2) returns true
 10. frame is dropped (oops!)

Fixes: d3c1597b ("mac80211: fix forwarded mesh frame queue mapping")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The driver can access the queue simultanously
while mac80211 tears down the interface. Without
spinlock protection this could lead to corrupting
sk_buff_head and subsequently to an invalid
pointer dereference.

Fixes: ba8c3d6f ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Remove unnecessory "if" statement and club it with previos "if" block.
Signed-off-by: Sunil Shahu <shshahu@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a note to userspace on the effect of RFKILL_OP_CHANGE_ALL also
updating the default state for hotplugged devices.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
[reword a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This was scheduled to be removed in 2012 by:

 commit 69c86373
 Author: florian@mickler.org <florian@mickler.org>
 Date:   Wed Feb 24 12:05:16 2010 +0100

     Document the rfkill sysfs ABI

     This moves sysfs ABI info from Documentation/rfkill.txt to the
     ABI subfolder and reformats it.

     This also schedules the deprecated sysfs parts to be removed in
     2012 (claim file) and 2014 (state file).
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

__rfkill_set_hw_state() is only one used in rfkill_set_hw_state(), and
none of them are long or complicated, so merging the two makes the code
easier to read.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

RFKILL_BLOCK_SW value have just been saved to prev, no need to check it
again in the if expression. This makes code a little bit easier to read.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When suspended while polling is paused, polling will erroneously
resume at resume time. Fix this by tracking pause and suspend in
separate state variable and adding the necessary checks.

Clarify the documentation on this as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The function here already has a variable hdr that even
contains the right thing, so the inner scope's hdr variable
that's shadowing the outer one can just be removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Make the addr parameter const in SET_IEEE80211_PERM_ADDR() to save
clients from having to cast away a const qualifier.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The station MLME and IBSS/mesh ones use entirely different
code for interpreting HT and VHT operation elements. Change
the code that interprets them a bit - it now modifies an
existing chandef - and use it also in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Print a warning whenever an expected callback function
lacks implementation.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In VHT, the specification allows to limit the number of
MSDUs in an A-MSDU in the Extended Capabilities IE. There
is also a limitation on the byte size in the VHT IE.
In HT, the only limitation is on the byte size.
Parse the capabilities from the peer and make them
available to the driver.

In HT, there is another limitation when a BA agreement
is active: the byte size can't be greater than 4095.
This is not enforced here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The minimum chandef bandwidth calculation was done only in case
a new station was inserted (or when an existing station was removed).
However, it is possible that stations are inserted before they are
associated, e.g., when FULL_AP_CLIENT_STATE is supported and user
space adds stations unassociated.

Fix this by calling ieee80211_recalc_min_chandef() whenever
a station transitions in/out the associated state, and only
consider station marked as associated.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some drivers offload some frames internally (e.g.
AddBa). Reporting such frames to mac80211 would
only confuse MLME. However it would be useful to
be able to pass such frames to monitor interfaces
for sniffing purposes, e.g. when running AP +
monitor.

To do that allow drivers to tell mac80211 whether
a given frame should be:
 - processed but not delivered to any monitor vif
 - not processed but delievered to monitor vifs
   only
Signed-off-by: Grzegorz Bajorski <grzegorz.bajorski@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Enable driver to manage the reordering logic itself.
This is needed for example for the iwlwifi driver that
will support hardware assisted reordering.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

It's not always necessary to set the status.freq field, for example
when this would be an expensive calculation. It must be set for all
management frames (as they might be reported to userspace), but for
data frames it's not really required. Document this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently mac80211 does not inform the driver of the window
size when starting an RX aggregation session.
To enable managing the reorder buffer in the driver or hardware
the window size is needed.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add an option for driver to check for packet duplication
by itself.
This is needed for example by the iwlwifi driver which
parallelizes the RX path and does the duplication check
per queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The Group ID Management frame is an Action frame of
category VHT. It is transmitted by the AP to assign
or change the user position of a STA for one or more
group IDs.
Process and save the group membership data. Notify
underlying driver of changes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of having this Kconfig option, which just *floods* the
kernel log,
 * remove the per-channel prints that are fairly useless anyway
 * convert the conditional printing to pr_debug()
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull oower management and ACPI updates from Rafael Wysocki:
 "As far as the number of commits goes, ACPICA takes the lead this time,
  followed by cpufreq and the device properties framework changes.

  The most significant new feature is the debugfs-based interface to the
  ACPICA's AML debugger added in the previous cycle and a new user space
  tool for accessing it.

  On the cpufreq front, the core is updated to handle governors more
  efficiently, particularly on systems where a single cpufreq policy
  object is shared between multiple CPUs, and there are quite a few
  changes in drivers (intel_pstate, cpufreq-dt etc).

  The device properties framework is updated to handle built-in (ie
  included in the kernel itself) device properties better, among other
  things by adding a fallback mechanism that will allow drivers to
  provide default properties to be used in case the plaform firmware
  doesn't provide the properties expected by them.

  The Operating Performance Points (OPP) framework gets new DT bindings
  and debugfs support.

  A new cpufreq driver for ST platforms is added and the ACPI driver for
  AMD SoCs will now support the APM X-Gene ACPI I2C device.

  The rest is mostly fixes and cleanups all over.

  Specifics:

   - Add a debugfs-based interface for interacting with the ACPICA's AML
     debugger introduced in the previous cycle and a new user space tool
     for that, fix some bugs related to the AML debugger and clean up
     the code in question (Lv Zheng, Dan Carpenter, Colin Ian King,
     Markus Elfring).

   - Update ACPICA to upstream revision 20151218 including a number of
     fixes and cleanups in the ACPICA core (Bob Moore, Lv Zheng, Labbe
     Corentin, Prarit Bhargava, Colin Ian King, David E Box, Rafael
     Wysocki).

     In particular, the previously added erroneous support for the _SUB
     object is dropped, the concatenate operator will support all ACPI
     objects now, the Debug Object handling is improved, the SuperName
     handling of parameters being control methods is fixed, the
     ObjectType operator handling is updated to follow ACPI 5.0A and the
     handling of CondRefOf and RefOf is updated accordingly, module-
     level code will be executed after loading each ACPI table now
     (instead of being run once after all tables containing AML have
     been loaded), the Operation Region handlers management is updated
     to fix some reported problems and a the ACPICA code in the kernel
     is more in line with the upstream now.

   - Update the ACPI backlight driver to provide information on whether
     or not it will generate key-presses for brightness change hotkeys
     and update some platform drivers (dell-wmi, thinkpad_acpi) to use
     that information to avoid sending double key-events to users pace
     for these, add new ACPI backlight quirks (Hans de Goede, Aaron Lu,
     Adrien Schildknecht).

   - Improve the ACPI handling of interrupt GPIOs (Christophe Ricard).

   - Fix the handling of the list of device IDs of device objects found
     in the ACPI namespace and add a helper for checking if there is a
     device object for a given device ID (Lukas Wunner).

   - Change the logic in the ACPI namespace scanning code to create
     struct acpi_device objects for all ACPI device objects found in the
     namespace even if _STA fails for them which helps to avoid device
     enumeration problems on Microsoft Surface 3 (Aaron Lu).

   - Add support for the APM X-Gene ACPI I2C device to the ACPI driver
     for AMD SoCs (Loc Ho).

   - Fix the long-standing issue with the DMA controller on Intel SoCs
     where ACPI tables have no power management support for the DMA
     controller itself, but it can be powered off automatically when the
     last (other) device on the SoC is powered off via ACPI and clean up
     the ACPI driver for Intel SoCs (acpi-lpss) after previous attempts
     to fix that problem (Andy Shevchenko).

   - Assorted ACPI fixes and cleanups (Andy Lutomirski, Colin Ian King,
     Javier Martinez Canillas, Ken Xue, Mathias Krause, Rafael Wysocki,
     Sinan Kaya).

   - Update the device properties framework for better handling of
     built-in properties, add support for built-in properties to the
     platform bus type, update the MFD subsystem's handling of device
     properties and add support for passing default configuration data
     as device properties to the intel-lpss MFD drivers, convert the
     designware I2C driver to use the unified device properties API and
     add a fallback mechanism for using default built-in properties if
     the platform firmware fails to provide the properties as expected
     by drivers (Andy Shevchenko, Mika Westerberg, Heikki Krogerus,
     Andrew Morton).

   - Add new Device Tree bindings to the Operating Performance Points
     (OPP) framework and update the exynos4412 DT binding accordingly,
     introduce debugfs support for the OPP framework (Viresh Kumar,
     Bartlomiej Zolnierkiewicz).

   - Migrate the mt8173 cpufreq driver to the new OPP bindings (Pi-Cheng
     Chen).

   - Update the cpufreq core to make the handling of governors more
     efficient, especially on systems where policy objects are shared
     between multiple CPUs (Viresh Kumar, Rafael Wysocki).

   - Fix cpufreq governor handling on configurations with
     CONFIG_HZ_PERIODIC set (Chen Yu).

   - Clean up the cpufreq core code related to the boost sysfs knob
     support and update the ACPI cpufreq driver accordingly (Rafael
     Wysocki).

   - Add a new cpufreq driver for ST platforms and corresponding Device
     Tree bindings (Lee Jones).

   - Update the intel_pstate driver to allow the P-state selection
     algorithm used by it to depend on the CPU ID of the processor it is
     running on, make it use a special P-state selection algorithm (with
     an IO wait time compensation tweak) on Atom CPUs based on the
     Airmont and Silvermont cores so as to reduce their energy
     consumption and improve intel_pstate documentation (Philippe
     Longepe, Srinivas Pandruvada).

   - Update the cpufreq-dt driver to support registering cooling devices
     that use the (P * V^2 * f) dynamic power draw formula where V is
     the voltage, f is the frequency and P is a constant coefficient
     provided by Device Tree and update the arm_big_little cpufreq
     driver to use that support (Punit Agrawal).

   - Assorted cpufreq driver (cpufreq-dt, qoriq, pcc-cpufreq,
     blackfin-cpufreq) updates (Andrzej Hajda, Hongtao Jia, Jacob
     Tanenbaum, Markus Elfring).

   - cpuidle core tweaks related to polling and measured_us calculation
     (Rik van Riel).

   - Removal of modularity from a few cpuidle drivers (clps711x, ux500,
     exynos) that cannot be built as modules in practice (Paul
     Gortmaker).

   - PM core update to prevent devices from being probed during system
     suspend/resume which is generally problematic and may lead to
     inconsistent behavior (Grygorii Strashko).

   - Assorted updates of the PM core and related code (Julia Lawall,
     Manuel Pégourié-Gonnard, Maruthi Bayyavarapu, Rafael Wysocki, Ulf
     Hansson).

   - PNP bus type updates (Christophe Le Roy, Heiner Kallweit).

   - PCI PM code cleanups (Jarkko Nikula, Julia Lawall).

   - cpupower tool updates (Jacob Tanenbaum, Thomas Renninger)"

* tag 'pm+acpi-4.5-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (177 commits)
  PM / clk: don't leave clocks enabled when driver not bound
  i2c: dw: Add APM X-Gene ACPI I2C device support
  ACPI / APD: Add APM X-Gene ACPI I2C device support
  ACPI / LPSS: change 'does not have' to 'has' in comment
  Revert "dmaengine: dw: platform: provide platform data for Intel"
  dmaengine: dw: return immediately from IRQ when DMA isn't in use
  dmaengine: dw: platform: power on device on shutdown
  ACPI / LPSS: override power state for LPSS DMA device
  PM / OPP: Use snprintf() instead of sprintf()
  Documentation: cpufreq: intel_pstate: enhance documentation
  ACPI, PCI, irq: remove redundant check for null string pointer
  ACPI / video: driver must be registered before checking for keypresses
  cpufreq-dt: fix handling regulator_get_voltage() result
  cpufreq: governor: Fix negative idle_time when configured with CONFIG_HZ_PERIODIC
  PM / sleep: Add support for read-only sysfs attributes
  ACPI: Fix white space in a structure definition
  ACPI / SBS: fix inconsistent indenting inside if statement
  PNP: respect PNP_DRIVER_RES_DO_NOT_CHANGE when detaching
  ACPI / PNP: constify device IDs
  ACPI / PCI: Simplify acpi_penalize_isa_irq()
  ...

Pull tracing updates from Steven Rostedt:
 "Not much new with tracing for this release.  Mostly just clean ups and
  minor fixes.

  Here's what else is new:

   - A new TRACE_EVENT_FN_COND macro, combining both _FN and _COND for
     those that want both.

   - New selftest to test the instance create and delete

   - Better debug output when ftrace fails"

* tag 'trace-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (24 commits)
  ftrace: Fix the race between ftrace and insmod
  ftrace: Add infrastructure for delayed enabling of module functions
  x86: ftrace: Fix the comments for ftrace_modify_code_direct()
  tracing: Fix comment to use tracing_on over tracing_enable
  metag: ftrace: Fix the comments for ftrace_modify_code
  sh: ftrace: Fix the comments for ftrace_modify_code()
  ia64: ftrace: Fix the comments for ftrace_modify_code()
  ftrace: Clean up ftrace_module_init() code
  ftrace: Join functions ftrace_module_init() and ftrace_init_module()
  tracing: Introduce TRACE_EVENT_FN_COND macro
  tracing: Use seq_buf_used() in seq_buf_to_user() instead of len
  bpf: Constify bpf_verifier_ops structure
  ftrace: Have ftrace_ops_get_func() handle RCU and PER_CPU flags too
  ftrace: Remove use of control list and ops
  ftrace: Fix output of enabled_functions for showing tramp
  ftrace: Fix a typo in comment
  ftrace: Show all tramps registered to a record on ftrace_bug()
  ftrace: Add variable ftrace_expected for archs to show expected code
  ftrace: Add new type to distinguish what kind of ftrace_bug()
  tracing: Update cond flag when enabling or disabling a trigger
  ...

Pull cgroup updates from Tejun Heo:

 - cgroup v2 interface is now official.  It's no longer hidden behind a
   devel flag and can be mounted using the new cgroup2 fs type.

   Unfortunately, cpu v2 interface hasn't made it yet due to the
   discussion around in-process hierarchical resource distribution and
   only memory and io controllers can be used on the v2 interface at the
   moment.

 - The existing documentation which has always been a bit of mess is
   relocated under Documentation/cgroup-v1/. Documentation/cgroup-v2.txt
   is added as the authoritative documentation for the v2 interface.

 - Some features are added through for-4.5-ancestor-test branch to
   enable netfilter xt_cgroup match to use cgroup v2 paths.  The actual
   netfilter changes will be merged through the net tree which pulled in
   the said branch.

 - Various cleanups

* 'for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: rename cgroup documentations
  cgroup: fix a typo.
  cgroup: Remove resource_counter.txt in Documentation/cgroup-legacy/00-INDEX.
  cgroup: demote subsystem init messages to KERN_DEBUG
  cgroup: Fix uninitialized variable warning
  cgroup: put controller Kconfig options in meaningful order
  cgroup: clean up the kernel configuration menu nomenclature
  cgroup_pids: fix a typo.
  Subject: cgroup: Fix incomplete dd command in blkio documentation
  cgroup: kill cgrp_ss_priv[CGROUP_CANFORK_COUNT] and friends
  cpuset: Replace all instances of time_t with time64_t
  cgroup: replace unified-hierarchy.txt with a proper cgroup v2 documentation
  cgroup: rename Documentation/cgroups/ to Documentation/cgroup-legacy/
  cgroup: replace __DEVEL__sane_behavior with cgroup2 fs type

Pull networking updates from Davic Miller:

 1) Support busy polling generically, for all NAPI drivers.  From Eric
    Dumazet.

 2) Add byte/packet counter support to nft_ct, from Floriani Westphal.

 3) Add RSS/XPS support to mvneta driver, from Gregory Clement.

 4) Implement IPV6_HDRINCL socket option for raw sockets, from Hannes
    Frederic Sowa.

 5) Add support for T6 adapter to cxgb4 driver, from Hariprasad Shenai.

 6) Add support for VLAN device bridging to mlxsw switch driver, from
    Ido Schimmel.

 7) Add driver for Netronome NFP4000/NFP6000, from Jakub Kicinski.

 8) Provide hwmon interface to mlxsw switch driver, from Jiri Pirko.

 9) Reorganize wireless drivers into per-vendor directories just like we
    do for ethernet drivers.  From Kalle Valo.

10) Provide a way for administrators "destroy" connected sockets via the
    SOCK_DESTROY socket netlink diag operation.  From Lorenzo Colitti.

11) Add support to add/remove multicast routes via netlink, from Nikolay
    Aleksandrov.

12) Make TCP keepalive settings per-namespace, from Nikolay Borisov.

13) Add forwarding and packet duplication facilities to nf_tables, from
    Pablo Neira Ayuso.

14) Dead route support in MPLS, from Roopa Prabhu.

15) TSO support for thunderx chips, from Sunil Goutham.

16) Add driver for IBM's System i/p VNIC protocol, from Thomas Falcon.

17) Rationalize, consolidate, and more completely document the checksum
    offloading facilities in the networking stack.  From Tom Herbert.

18) Support aborting an ongoing scan in mac80211/cfg80211, from
    Vidyullatha Kanchanapally.

19) Use per-bucket spinlock for bpf hash facility, from Tom Leiming.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1375 commits)
  net: bnxt: always return values from _bnxt_get_max_rings
  net: bpf: reject invalid shifts
  phonet: properly unshare skbs in phonet_rcv()
  dwc_eth_qos: Fix dma address for multi-fragment skbs
  phy: remove an unneeded condition
  mdio: remove an unneed condition
  mdio_bus: NULL dereference on allocation error
  net: Fix typo in netdev_intersect_features
  net: freescale: mac-fec: Fix build error from phy_device API change
  net: freescale: ucc_geth: Fix build error from phy_device API change
  bonding: Prevent IPv6 link local address on enslaved devices
  IB/mlx5: Add flow steering support
  net/mlx5_core: Export flow steering API
  net/mlx5_core: Make ipv4/ipv6 location more clear
  net/mlx5_core: Enable flow steering support for the IB driver
  net/mlx5_core: Initialize namespaces only when supported by device
  net/mlx5_core: Set priority attributes
  net/mlx5_core: Connect flow tables
  net/mlx5_core: Introduce modify flow table command
  net/mlx5_core: Managing root flow table
  ...

Pull crypto update from Herbert Xu:
 "Algorithms:
   - Add RSA padding algorithm

  Drivers:
   - Add GCM mode support to atmel
   - Add atmel support for SAMA5D2 devices
   - Add cipher modes to talitos
   - Add rockchip driver for rk3288
   - Add qat support for C3XXX and C62X"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (103 commits)
  crypto: hifn_795x, picoxcell - use ablkcipher_request_cast
  crypto: qat - fix SKU definiftion for c3xxx dev
  crypto: qat - Fix random config build issue
  crypto: ccp - use to_pci_dev and to_platform_device
  crypto: qat - Rename dh895xcc mmp firmware
  crypto: 842 - remove WARN inside printk
  crypto: atmel-aes - add debug facilities to monitor register accesses.
  crypto: atmel-aes - add support to GCM mode
  crypto: atmel-aes - change the DMA threshold
  crypto: atmel-aes - fix the counter overflow in CTR mode
  crypto: atmel-aes - fix atmel-ctr-aes driver for RFC 3686
  crypto: atmel-aes - create sections to regroup functions by usage
  crypto: atmel-aes - fix typo and indentation
  crypto: atmel-aes - use SIZE_IN_WORDS() helper macro
  crypto: atmel-aes - improve performances of data transfer
  crypto: atmel-aes - fix atmel_aes_remove()
  crypto: atmel-aes - remove useless AES_FLAGS_DMA flag
  crypto: atmel-aes - reduce latency of DMA completion
  crypto: atmel-aes - remove unused 'err' member of struct atmel_aes_dev
  crypto: atmel-aes - rework crypto request completion
  ...

Pull UBI/UBIFS updates from Richard Weinberger:
 "This contains three changes - two cleanups and one UBI wear leveling
  improvement by Sebastian Siewior"

* tag 'upstream-4.5-rc1' of git://git.infradead.org/linux-ubifs:
  ubifs: Use XATTR_*_PREFIX_LEN
  UBIFS: add a comment in key.h for unused parameter
  mtd: ubi: wl: avoid erasing a PEB which is empty

Pull configfs updates from Christoph Hellwig:
 "I'm assisting Joel as co-maintainer and patch monkey now, and you will
  see pull reuquests from me for a while.

  Besides the MAINTAINERS update there is just a single change, which
  adds support for binary attributes to configfs, which are very similar
  to the sysfs binary attributes.  Thanks to Pantelis Antoniou!

  You will see another actually bigger set of configfs changes in the
  SCSI target pull from Nic - those were merged before this new tree
  even existed"

* tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs:
  configfs: add myself as co-maintainer, updated git tree
  configfs: implement binary attributes

Pull GFS2 updates from Bob Peterson:
 "Here is a list of patches we've accumulated for GFS2 for the current
  upstream merge window.  Last window's set was short, but I warned that
  this one would be bigger, and so it is.  We've got 19 patches:

   - A patch from Abhi Das to propagate the GFS2_DIF_SYSTEM bit so that
     newly added journals don't get flagged, deleted, and recreated by
     fsck.gfs2.

   - Two patches from Andreas Gruenbacher to improve GFS2 performance
     where extended attributes are involved.

   - A patch from Andy Price to fix a suspicious rcu dereference error.

   - Two patches from Ben Marzinski that rework how GFS2's NFS cookies
     are managed.  This fixes readdir problems with nfs-over-gfs2.

   - A patch from Ben Marzinski that fixes a race in unmounting GFS2.

   - A set of four patches from me to move the resource group
     reservations inside the gfs2 inode to improve performance and fix a
     bug whereby get_write_access improperly prevented some operations
     like chown.

   - A patch from me to spinlock-protect the setting of system statfs
     file data.  This was causing small discrepancies between df and du.

   - A patch from me to reintroduce a timeout while clearing glocks
     which was accidentally dropped some time ago.

   - A patch from me to wait for iopen glock dequeues in order to
     improve deleting of files that were unlinked from a different
     cluster node.

   - A patch from me to ensure metadata address spaces get truncated
     when an inode is evicted.

   - A patch from me to fix a bug in which a memory leak could occur in
     some error cases when inodes were trying to be created.

   - A patch to consistently use iopen glocks to transition from the
     unlinked state to the deleted state.

   - A patch to fix a glock reference count error when inode creation
     fails.

   - A patch from Junxiao Bi to fix an flock panic.

   - A patch from Markus Elfring that removes an unnecessary if"

* tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: fix flock panic issue
  GFS2: Don't do glock put on when inode creation fails
  GFS2: Always use iopen glock for gl_deletes
  GFS2: Release iopen glock in gfs2_create_inode error cases
  GFS2: Truncate address space mapping when deleting an inode
  GFS2: Wait for iopen glock dequeues
  gfs2: clear journal live bit in	gfs2_log_flush
  gfs2: change gfs2 readdir cookie
  gfs2: keep offset when splitting dir leaf blocks
  GFS2: Reintroduce a timeout in function gfs2_gl_hash_clear
  GFS2: Update master statfs buffer with sd_statfs_spin locked
  GFS2: Reduce size of incore inode
  GFS2: Make rgrp reservations part of the gfs2_inode structure
  GFS2: Extract quota data from reservations structure (revert 5407e242)
  gfs2: Extended attribute readahead optimization
  gfs2: Extended attribute readahead
  GFS2: Use rht_for_each_entry_rcu in glock_hash_walk
  GFS2: Delete an unnecessary check before the function call "iput"
  gfs2: Automatically set GFS2_DIF_SYSTEM flag on system files

Pull misc vfs updates from Al Viro:
 "All kinds of stuff.  That probably should've been 5 or 6 separate
  branches, but by the time I'd realized how large and mixed that bag
  had become it had been too close to -final to play with rebasing.

  Some fs/namei.c cleanups there, memdup_user_nul() introduction and
  switching open-coded instances, burying long-dead code, whack-a-mole
  of various kinds, several new helpers for ->llseek(), assorted
  cleanups and fixes from various people, etc.

  One piece probably deserves special mention - Neil's
  lookup_one_len_unlocked().  Similar to lookup_one_len(), but gets
  called without ->i_mutex and tries to avoid ever taking it.  That, of
  course, means that it's not useful for any directory modifications,
  but things like getting inode attributes in nfds readdirplus are fine
  with that.  I really should've asked for moratorium on lookup-related
  changes this cycle, but since I hadn't done that early enough...  I
  *am* asking for that for the coming cycle, though - I'm going to try
  and get conversion of i_mutex to rwsem with ->lookup() done under lock
  taken shared.

  There will be a patch closer to the end of the window, along the lines
  of the one Linus had posted last May - mechanical conversion of
  ->i_mutex accesses to inode_lock()/inode_unlock()/inode_trylock()/
  inode_is_locked()/inode_lock_nested().  To quote Linus back then:

    -----
    |    This is an automated patch using
    |
    |        sed 's/mutex_lock(&\(.*\)->i_mutex)/inode_lock(\1)/'
    |        sed 's/mutex_unlock(&\(.*\)->i_mutex)/inode_unlock(\1)/'
    |        sed 's/mutex_lock_nested(&\(.*\)->i_mutex,[     ]*I_MUTEX_\([A-Z0-9_]*\))/inode_lock_nested(\1, I_MUTEX_\2)/'
    |        sed 's/mutex_is_locked(&\(.*\)->i_mutex)/inode_is_locked(\1)/'
    |        sed 's/mutex_trylock(&\(.*\)->i_mutex)/inode_trylock(\1)/'
    |
    |    with a very few manual fixups
    -----

  I'm going to send that once the ->i_mutex-affecting stuff in -next
  gets mostly merged (or when Linus says he's about to stop taking
  merges)"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
  nfsd: don't hold i_mutex over userspace upcalls
  fs:affs:Replace time_t with time64_t
  fs/9p: use fscache mutex rather than spinlock
  proc: add a reschedule point in proc_readfd_common()
  logfs: constify logfs_block_ops structures
  fcntl: allow to set O_DIRECT flag on pipe
  fs: __generic_file_splice_read retry lookup on AOP_TRUNCATED_PAGE
  fs: xattr: Use kvfree()
  [s390] page_to_phys() always returns a multiple of PAGE_SIZE
  nbd: use ->compat_ioctl()
  fs: use block_device name vsprintf helper
  lib/vsprintf: add %*pg format specifier
  fs: use gendisk->disk_name where possible
  poll: plug an unused argument to do_poll
  amdkfd: don't open-code memdup_user()
  cdrom: don't open-code memdup_user()
  rsxx: don't open-code memdup_user()
  mtip32xx: don't open-code memdup_user()
  [um] mconsole: don't open-code memdup_user_nul()
  [um] hostaudio: don't open-code memdup_user()
  ...

Pull iov_iter infrastructure updates from Al Viro:
 "A couple of iov_iter updates"

* 'work.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  iov_iter: export import_single_range()
  iov_iter: constify {csum_and_,}copy_to_iter()

Pull vfs copy_file_range updates from Al Viro:
 "Several series around copy_file_range/CLONE"

* 'work.copy_file_range' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  btrfs: use new dedupe data function pointer
  vfs: hoist the btrfs deduplication ioctl to the vfs
  vfs: wire up compat ioctl for CLONE/CLONE_RANGE
  cifs: avoid unused variable and label
  nfsd: implement the NFSv4.2 CLONE operation
  nfsd: Pass filehandle to nfs4_preprocess_stateid_op()
  vfs: pull btrfs clone API to vfs layer
  locks: new locks_mandatory_area calling convention
  vfs: Add vfs_copy_file_range() support for pagecache copies
  btrfs: add .copy_file_range file operation
  x86: add sys_copy_file_range to syscall tables
  vfs: add copy_file_range syscall and vfs helper