- 03 Feb, 2020 6 commits
-
-
Vasundhara Volam authored
The current logic that calls pci_disable_device() in __bnxt_close_nic() during firmware reset is flawed. If firmware is still alive, we're disabling the device too early, causing some firmware commands to not reach the firmware. Fix it by moving the logic to bnxt_reset_close(). If firmware is in fatal condition, we call pci_disable_device() before we free any of the rings to prevent DMA corruption of the freed rings. If firmware is still alive, we call pci_disable_device() after the last firmware message has been sent. Fixes: 3bc7d4a3 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.") Signed-off-by:
Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Michael Chan authored
bnxt_ulp_start() needs to be called before SRIOV is re-enabled after firmware reset. Re-enabling SRIOV may consume all the resources and may cause the RDMA driver to fail to get MSIX and other resources. Fix it by calling bnxt_ulp_start() first before calling bnxt_reenable_sriov(). We re-arrange the logic so that we call bnxt_ulp_start() and bnxt_reenable_sriov() in proper sequence in bnxt_fw_reset_task() and bnxt_open(). The former is the normal coordinated firmware reset sequence and the latter is firmware reset while the function is down. This new logic is now more straight forward and will now fix both scenarios. Fixes: f3a6d206 ("bnxt_en: Call bnxt_ulp_stop()/bnxt_ulp_start() during error recovery.") Reported-by:
-
Michael Chan authored
Put the current logic in bnxt_open() to re-enable SRIOV after detecting firmware reset into a new function bnxt_reenable_sriov(). This call needs to be invoked in the firmware reset path also in the next patch. Signed-off-by:
-
Nicolin Chen authored
When running v5.5 with a rootfs on NFS, memory abort may happen in the system resume stage: Unable to handle kernel paging request at virtual address dead00000000012a [dead00000000012a] address between user and kernel address ranges pc : run_timer_softirq+0x334/0x3d8 lr : run_timer_softirq+0x244/0x3d8 x1 : ffff800011cafe80 x0 : dead000000000122 Call trace: run_timer_softirq+0x334/0x3d8 efi_header_end+0x114/0x234 irq_exit+0xd0/0xd8 __handle_domain_irq+0x60/0xb0 gic_handle_irq+0x58/0xa8 el1_irq+0xb8/0x180 arch_cpu_idle+0x10/0x18 do_idle+0x1d8/0x2b0 cpu_startup_entry+0x24/0x40 secondary_start_kernel+0x1b4/0x208 Code: f9000693 a9400660 f9000020 b4000040 (f9000401) ---[ end trace bb83ceeb4c482071 ]--- Kernel panic - not syncing: Fatal exception in interrupt SMP: stopping secondary CPUs SMP: failed to stop secondary CPUs 2-3 Kernel Offset: disabled CPU features: 0x00002,2300aa30 Memory Limit: none ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]--- It's found that stmmac_xmit() and stmmac_resume() sometimes might run concurrently, possibly resulting in a race condition between mod_timer() and setup_timer(), being called by stmmac_xmit() and stmmac_resume() respectively. Since the resume() runs setup_timer() every time, it'd be safer to have del_timer_sync() in the suspend() as the counterpart. Signed-off-by:
Nicolin Chen <nicoleotsuka@gmail.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fsJakub Kicinski authored
David Howells says: ==================== RxRPC fixes Here are a number of fixes for AF_RXRPC: (1) Fix a potential use after free in rxrpc_put_local() where it was accessing the object just put to get tracing information. (2) Fix insufficient notifications being generated by the function that queues data packets on a call. This occasionally causes recvmsg() to stall indefinitely. (3) Fix a number of packet-transmitting work functions to hold an active count on the local endpoint so that the UDP socket doesn't get destroyed whilst they're calling kernel_sendmsg() on it. (4) Fix a NULL pointer deref that stemmed from a call's connection pointer being cleared when the call was disconnected. Changes: v2: Removed a couple of BUG() statements that got added. ==================== Signed-off-by: -
David Howells authored
When a call is disconnected, the connection pointer from the call is cleared to make sure it isn't used again and to prevent further attempted transmission for the call. Unfortunately, there might be a daemon trying to use it at the same time to transmit a packet. Fix this by keeping call->conn set, but setting a flag on the call to indicate disconnection instead. Remove also the bits in the transmission functions where the conn pointer is checked and a ref taken under spinlock as this is now redundant. Fixes: 8d94aa38 ("rxrpc: Calls shouldn't hold socket refs") Signed-off-by:
David Howells <dhowells@redhat.com>
-
- 02 Feb, 2020 4 commits
-
-
Jakub Kicinski authored
SeongJae Park says: ==================== Fix reconnection latency caused by FIN/ACK handling race The first patch fixes the problem by adjusting the first resend delay of the SYN in the case. The second one adds a user space test to reproduce this problem. From v2 (https://lore.kernel.org/linux-kselftest/20200201071859.4231-1-sj38.park@gmail.com/) - Use TCP_TIMEOUT_MIN as reduced delay (Neal Cardwall) - Add Reviewed-by and Signed-off-by from Eric Dumazet From v1 (https://lore.kernel.org/linux-kselftest/20200131122421.23286-1-sjpark@amazon.com/) - Drop the trivial comment fix patch (Eric Dumazet) - Limit the delay adjustment to only the first SYN resend (Eric Dumazet) - selftest: Avoid use of hard-coded port number (Eric Dumazet) - Explain RST/ACK and FIN/ACK has no big difference (Neal Cardwell) ==================== Signed-off-by:
-
SeongJae Park authored
This commit adds a test for FIN_ACK process races related reconnection latency spike issues. The issue has described and solved by the previous commit ("tcp: Reduce SYN resend delay if a suspicous ACK is received"). The test program is configured with a server and a client process. The server creates and binds a socket to a port that dynamically allocated, listen on it, and start a infinite loop. Inside the loop, it accepts connection, reads 4 bytes from the socket, and closes the connection. The client is constructed as an infinite loop. Inside the loop, it creates a socket with LINGER and NODELAY option, connect to the server, send 4 bytes data, try read some data from server. After the read() returns, it measure the latency from the beginning of this loop to this point and if the latency is larger than 1 second (spike), print a message. Reviewed-by:Eric Dumazet <edumazet@google.com> Signed-off-by:
SeongJae Park <sjpark@amazon.de> Signed-off-by:
-
SeongJae Park authored
When closing a connection, the two acks that required to change closing socket's status to FIN_WAIT_2 and then TIME_WAIT could be processed in reverse order. This is possible in RSS disabled environments such as a connection inside a host. For example, expected state transitions and required packets for the disconnection will be similar to below flow. 00 (Process A) (Process B) 01 ESTABLISHED ESTABLISHED 02 close() 03 FIN_WAIT_1 04 ---FIN--> 05 CLOSE_WAIT 06 <--ACK--- 07 FIN_WAIT_2 08 <--FIN/ACK--- 09 TIME_WAIT 10 ---ACK--> 11 LAST_ACK 12 CLOSED CLOSED In some cases such as LINGER option applied socket, the FIN and FIN/ACK will be substituted to RST and RST/ACK, but there is no difference in the main logic. The acks in lines 6 and 8 are the acks. If the line 8 packet is processed before the line 6 packet, it will be just ignored as it is not a expected packet, and the later process of the line 6 packet will change the status of Process A to FIN_WAIT_2, but as it has already handled line 8 packet, it will not go to TIME_WAIT and thus will not send the line 10 packet to Process B. Thus, Process B will left in CLOSE_WAIT status, as below. 00 (Process A) (Process B) 01 ESTABLISHED ESTABLISHED 02 close() 03 FIN_WAIT_1 04 ---FIN--> 05 CLOSE_WAIT 06 (<--ACK---) 07 (<--FIN/ACK---) 08 (fired in right order) 09 <--FIN/ACK--- 10 <--ACK--- 11 (processed in reverse order) 12 FIN_WAIT_2 Later, if the Process B sends SYN to Process A for reconnection using the same port, Process A will responds with an ACK for the last flow, which has no increased sequence number. Thus, Process A will send RST, wait for TIMEOUT_INIT (one second in default), and then try reconnection. If reconnections are frequent, the one second latency spikes can be a big problem. Below is a tcpdump results of the problem: 14.436259 IP 127.0.0.1.45150 > 127.0.0.1.4242: Flags [S], seq 2560603644 14.436266 IP 127.0.0.1.4242 > 127.0.0.1.45150: Flags [.], ack 5, win 512 14.436271 IP 127.0.0.1.45150 > 127.0.0.1.4242: Flags [R], seq 2541101298 /* ONE SECOND DELAY */ 15.464613 IP 127.0.0.1.45150 > 127.0.0.1.4242: Flags [S], seq 2560603644 This commit mitigates the problem by reducing the delay for the next SYN if the suspicous ACK is received while in SYN_SENT state. Following commit will add a selftest, which can be also helpful for understanding of this issue. Signed-off-by: -
Lukas Bulwahn authored
Commit 6d979850 ("isdn: move capi drivers to staging") cleaned up the isdn drivers and split the MAINTAINERS section for ISDN, but missed to add the terminal slash for the two directories mISDN and hardware. Hence, all files in those directories were not part of the new ISDN/mISDN SUBSYSTEM, but were considered to be part of "THE REST". Rectify the situation, and while at it, also complete the section with two further build files that belong to that subsystem. This was identified with a small script that finds all files belonging to "THE REST" according to the current MAINTAINERS file, and I investigated upon its output. Fixes: 6d979850 ("isdn: move capi drivers to staging") Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
- 01 Feb, 2020 9 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfJakub Kicinski authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Fix suspicious RCU usage in ipset, from Jozsef Kadlecsik. 2) Use kvcalloc, from Joe Perches. 3) Flush flowtable hardware workqueue after garbage collection run, from Paul Blakey. 4) Missing flowtable hardware workqueue flush from nf_flow_table_free(), also from Paul. 5) Restore NF_FLOW_HW_DEAD in flow_offload_work_del(), from Paul. 6) Flowtable documentation fixes, from Matteo Croce. ==================== Signed-off-by: -
Eric Dumazet authored
NLA_BINARY can be confusing, since .len value represents the max size of the blob. cls_rsvp really wants user space to provide long enough data for TCA_RSVP_DST and TCA_RSVP_SRC attributes. BUG: KMSAN: uninit-value in rsvp_get net/sched/cls_rsvp.h:258 [inline] BUG: KMSAN: uninit-value in gen_handle net/sched/cls_rsvp.h:402 [inline] BUG: KMSAN: uninit-value in rsvp_change+0x1ae9/0x4220 net/sched/cls_rsvp.h:572 CPU: 1 PID: 13228 Comm: syz-executor.1 Not tainted 5.5.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 rsvp_get net/sched/cls_rsvp.h:258 [inline] gen_handle net/sched/cls_rsvp.h:402 [inline] rsvp_change+0x1ae9/0x4220 net/sched/cls_rsvp.h:572 tc_new_tfilter+0x31fe/0x5010 net/sched/cls_api.c:2104 rtnetlink_rcv_msg+0xcb7/0x1570 net/core/rtnetlink.c:5415 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5442 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x45b349 Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f269d43dc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f269d43e6d4 RCX: 000000000045b349 RDX: 0000000000000000 RSI: 00000000200001c0 RDI: 0000000000000003 RBP: 000000000075bfc8 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 00000000000009c2 R14: 00000000004cb338 R15: 000000000075bfd4 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline] kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82 slab_alloc_node mm/slub.c:2774 [inline] __kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4382 __kmalloc_reserve net/core/skbuff.c:141 [inline] __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:209 alloc_skb include/linux/skbuff.h:1049 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1174 [inline] netlink_sendmsg+0x7d3/0x14d0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 6fa8c014 ("[NET_SCHED]: Use nla_policy for attribute validation in classifiers") Signed-off-by:
syzbot <syzkaller@googlegroups.com> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Sven Eckelmann authored
The current maintainer Arvid Brodin <arvid.brodin@alten.se> hasn't contributed to the kernel since 2015-02-27. His company mail address is also bouncing and the company confirmed (2020-01-31) that no Arvid Brodin is working for them: > Vi har dessvärre ingen Arvid Brodin som arbetar på ALTEN. A MIA person cannot be the maintainer. It is better to mark is as orphaned until some other person can jump in and take over the responsibility for HSR. Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
-
Dan Carpenter authored
If the qed_fw_overlay_mem_alloc() then we should return -ENOMEM instead of success. Fixes: 30d5f858 ("qed: FW 8.42.2.0 Add fw overlay feature") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Dan Carpenter authored
The otx2_mbox_get_rsp() function never returns NULL, it returns error pointers on error. Fixes: 34bfe0eb ("octeontx2-pf: MTU, MAC and RX mode config support") Signed-off-by:
-
Eric Dumazet authored
tp->segs_in and tp->segs_out need to be cleared in tcp_disconnect(). tcp_disconnect() is rarely used, but it is worth fixing it. Fixes: 2efd055c ("tcp: add tcpi_segs_in and tcpi_segs_out to tcp_info") Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Eric Dumazet authored
tp->data_segs_in and tp->data_segs_out need to be cleared in tcp_disconnect(). tcp_disconnect() is rarely used, but it is worth fixing it. Fixes: a44d6eac ("tcp: Add RFC4898 tcpEStatsPerfDataSegsOut/In") Signed-off-by:
-
Eric Dumazet authored
tp->delivered needs to be cleared in tcp_disconnect(). tcp_disconnect() is rarely used, but it is worth fixing it. Fixes: ddf1af6f ("tcp: new delivery accounting") Signed-off-by:
Yuchung Cheng <ycheng@google.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Eric Dumazet authored
total_retrans needs to be cleared in tcp_disconnect(). tcp_disconnect() is rarely used, but it is worth fixing it. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
- 31 Jan, 2020 10 commits
-
-
Matteo Croce authored
In the flowtable documentation there is a missing semicolon, the command as is would give this error: nftables.conf:5:27-33: Error: syntax error, unexpected devices, expecting newline or semicolon hook ingress priority 0 devices = { br0, pppoe-data }; ^^^^^^^ nftables.conf:4:12-13: Error: invalid hook (null) flowtable ft { ^^ Fixes: 19b351f1 ("netfilter: add flowtable documentation") Signed-off-by:Matteo Croce <mcroce@redhat.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Paul Blakey authored
During the refactor this was accidently removed. Fixes: ae290450 ("netfilter: flowtable: add nf_flow_offload_tuple() helper") Signed-off-by:
Paul Blakey <paulb@mellanox.com> Signed-off-by:
-
Paul Blakey authored
If entries exist when freeing a hardware offload enabled table, we queue work for hardware while running the gc iteration. Execute it (flush) after queueing. Fixes: c29f74e0 ("netfilter: nf_flow_table: hardware offload support") Signed-off-by:
-
Paul Blakey authored
On netdev down event, nf_flow_table_cleanup() is called for the relevant device and it cleans all the tables that are on that device. If one of those tables has hardware offload flag, nf_flow_table_iterate_cleanup flushes hardware and then runs the gc. But the gc can queue more hardware work, which will take time to execute. Instead first add the work, then flush it, to execute it now. Fixes: c29f74e0 ("netfilter: nf_flow_table: hardware offload support") Signed-off-by:
-
Joe Perches authored
Convert the uses of kvmalloc_array with __GFP_ZERO to the equivalent kvcalloc. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Nathan Chancellor authored
When building arm32 allmodconfig: ERROR: "__aeabi_uldivmod" [drivers/net/ethernet/mellanox/mlxsw/mlxsw_spectrum.ko] undefined! rate_bytes_ps has type u64, we need to use a 64-bit division helper to avoid a build error. Fixes: a44f58c4 ("mlxsw: spectrum_qdisc: Support offloading of TBF Qdisc") Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Reviewed-by:
Ido Schimmel <idosch@mellanox.com> Tested-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Shannon Nelson authored
Be sure to include all the packet type bits in the mask. Fixes: fbfb8031 ("ionic: Add hardware init and device commands") Signed-off-by:
Shannon Nelson <snelson@pensando.io> Signed-off-by:
-
Michael Walle authored
The probe() might enable a VDDIO regulator, which needs to be disabled again before calling regulator_put(). Add a remove() function. Fixes: 2f664823 ("net: phy: at803x: add device tree binding") Signed-off-by:
Michael Walle <michael@walle.cc> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Michael Walle authored
If phydev->mii_ts is set by the PHY driver, it will always be overwritten in of_mdiobus_register_phy(). Fix it. Also make sure, that the unregister() doesn't do anything if the mii_timestamper was provided by the PHY driver. Fixes: 1dca22b1 ("net: mdio: of: Register discovered MII time stampers.") Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Michael Walle authored
of_find_mii_timestamper() returns NULL if no timestamper is found. Therefore, guard the unregister_mii_timestamper() calls. Fixes: 1dca22b1 ("net: mdio: of: Register discovered MII time stampers.") Signed-off-by:
-
- 30 Jan, 2020 11 commits
-
-
David Howells authored
The introduction of a split between the reference count on rxrpc_local objects and the usage count didn't quite go far enough. A number of kernel work items need to make use of the socket to perform transmission. These also need to get an active count on the local object to prevent the socket from being closed. Fix this by getting the active count in those places. Also split out the raw active count get/put functions as these places tend to hold refs on the rxrpc_local object already, so getting and putting an extra object ref is just a waste of time. The problem can lead to symptoms like: BUG: kernel NULL pointer dereference, address: 0000000000000018 .. CPU: 2 PID: 818 Comm: kworker/u9:0 Not tainted 5.5.0-fscache+ #51 ... RIP: 0010:selinux_socket_sendmsg+0x5/0x13 ... Call Trace: security_socket_sendmsg+0x2c/0x3e sock_sendmsg+0x1a/0x46 rxrpc_send_keepalive+0x131/0x1ae rxrpc_peer_keepalive_worker+0x219/0x34b process_one_work+0x18e/0x271 worker_thread+0x1a3/0x247 kthread+0xe6/0xeb ret_from_fork+0x1f/0x30 Fixes: 730c5fd4 ("rxrpc: Fix local endpoint refcounting") Signed-off-by: -
David Howells authored
In rxrpc_input_data(), rxrpc_notify_socket() is called if the base sequence number of the packet is immediately following the hard-ack point at the end of the function. However, this isn't sufficient, since the recvmsg side may have been advancing the window and then overrun the position in which we're adding - at which point rx_hard_ack >= seq0 and no notification is generated. Fix this by always generating a notification at the end of the input function. Without this, a long call may stall, possibly indefinitely. Fixes: 248f219c ("rxrpc: Rewrite the data and ack handling code") Signed-off-by:
-
David Howells authored
Fix rxrpc_put_local() to not access local->debug_id after calling atomic_dec_return() as, unless that returned n==0, we no longer have the right to access the object. Fixes: 06d9532f ("rxrpc: Fix read-after-free in rxrpc_queue_local()") Signed-off-by:
-
git://anongit.freedesktop.org/drm/drmLinus Torvalds authored
Pull drm updates from Davbe Airlie: "This is the main pull request for graphics for 5.6. Usual selection of changes all over. I've got one outstanding vmwgfx pull that touches mm so kept it separate until after all of this lands. I'll try and get it to you soon after this, but it might be early next week (nothing wrong with code, just my schedule is messy) This also hits a lot of fbdev drivers with some cleanups. Other notables: - vulkan timeline semaphore support added to syncobjs - nouveau turing secureboot/graphics support - Displayport MST display stream compression support Detailed summary: uapi: - dma-buf heaps added (and fixed) - command line add support for panel oreientation - command line allow overriding penguin count drm: - mipi dsi definition updates - lockdep annotations for dma_resv - remove dma-buf kmap/kunmap support - constify fb_ops in all fbdev drivers - MST fix for daisy chained hotplug- - CTA-861-G modes with VIC >= 193 added - fix drm_panel_of_backlight export - LVDS decoder support - more device based logging support - scanline alighment for dumb buffers - MST DSC helpers scheduler: - documentation fixes - job distribution improvements panel: - Logic PD type 28 panel support - Jimax8729d MIPI-DSI - igenic JZ4770 - generic DSI devicetree bindings - sony acx424AKP panel - Leadtek LTK500HD1829 - xinpeng XPP055C272 - AUO B116XAK01 - GiantPlus GPM940B0 - BOE NV140FHM-N49 - Satoz SAT050AT40H12R2 - Sharp LS020B1DD01D panels. ttm: - use blocking WW lock i915: - hw/uapi state separation - Lock annotation improvements - selftest improvements - ICL/TGL DSI VDSC support - VBT parsing improvments - Display refactoring - DSI updates + fixes - HDCP 2.2 for CFL - CML PCI ID fixes - GLK+ fbc fix - PSR fixes - GEN/GT refactor improvments - DP MST fixes - switch context id alloc to xarray - workaround updates - LMEM debugfs support - tiled monitor fixes - ICL+ clock gating programming removed - DP MST disable sequence fixed - LMEM discontiguous object maps - prefaulting for discontiguous objects - use LMEM for dumb buffers if possible - add LMEM mmap support amdgpu: - enable sync object timelines for vulkan - MST atomic routines - enable MST DSC support - add DMCUB display microengine support - DC OEM i2c support - Renoir DC fixes - Initial HDCP 2.x support - BACO support for Arcturus - Use BACO for runtime PM power save - gfxoff on navi10 - gfx10 golden updates and fixes - DCN support on POWER - GFXOFF for raven1 refresh - MM engine idle handlers cleanup - 10bpc EDP panel fixes - renoir watermark fixes - SR-IOV fixes - Arcturus VCN fixes - GDDR6 training fixes - freesync fixes - Pollock support amdkfd: - unify more codepath with amdgpu - use KIQ to setup HIQ rather than MMIO radeon: - fix vma fault handler race - PPC DMA fix - register check fixes for r100/r200 nouveau: - mmap_sem vs dma_resv fix - rewrite the ACR secure boot code for Turing - TU10x graphics engine support (TU11x pending) - Page kind mapping for turing - 10-bit LUT support - GP10B Tegra fixes - HD audio regression fix hisilicon/hibmc: - use generic fbdev code and helpers rockchip: - dsi/px30 support virtio: - fb damage support - static some functions vc4: - use dma_resv lock wrappers msm: - use dma_resv lock wrappers - sc7180 display + DSI support - a618 support - UBWC support improvements vmwgfx: - updates + new logging uapi exynos: - enable/disable callback cleanups etnaviv: - use dma_resv lock wrappers atmel-hlcdc: - clock fixes mediatek: - cmdq support - non-smooth cursor fixes - ctm property support sun4i: - suspend support - A64 mipi dsi support rcar-du: - Color management module support - LVDS encoder dual-link support - R8A77980 support analogic: - add support for an6345 ast: - atomic modeset support - primary plane garbage fix arcgpu: - fixes for fourcc handling tegra: - minor fixes and improvments mcde: - vblank support meson: - OSD1 plane AFBC commit gma500: - add pageflip support - reomve global drm_dev komeda: - tweak debugfs output - d32 support - runtime PM suppotr udl: - use generic shmem helpers - cleanup and fixes" * tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm: (1998 commits) drm/nouveau/fb/gp102-: allow module to load even when scrubber binary is missing drm/nouveau/acr: return error when registering LSF if ACR not supported drm/nouveau/disp/gv100-: not all channel types support reporting error codes drm/nouveau/disp/nv50-: prevent oops when no channel method map provided drm/nouveau: support synchronous pushbuf submission drm/nouveau: signal pending fences when channel has been killed drm/nouveau: reject attempts to submit to dead channels drm/nouveau: zero vma pointer even if we only unreference it rather than free drm/nouveau: Add HD-audio component notifier support drm/nouveau: fix build error without CONFIG_IOMMU_API drm/nouveau/kms/nv04: remove set but not used variable 'width' drm/nouveau/kms/nv50: remove set but not unused variable 'nv_connector' drm/nouveau/mmu: fix comptag memory leak drm/nouveau/gr/gp10b: Use gp100_grctx and gp100_gr_zbc drm/nouveau/pmu/gm20b,gp10b: Fix Falcon bootstrapping drm/exynos: Rename Exynos to lowercase drm/exynos: change callback names drm/mst: Don't do atomic checks over disabled managers drm/amdgpu: add the lost mutex_init back drm/amd/display: skip opp blank or unblank if test pattern enabled ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supplyLinus Torvalds authored
Pull power supply and reset updates from Sebastian Reichel: "Core: - Add battery internal resistance temperature table support Drivers: - sc27xx: Optimize the battery resistance with measuring temperature - max17042-battery: Add MAX17055 support - bq25890-charger: Add support of BQ25892 and BQ25896 chips - misc fixes" * tag 'for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (44 commits) power: supply: ipaq_micro_battery: remove unneeded semicolon power: supply: bq25890_charger: fix incorrect error return when bq25890_field_read fails power: supply: axp20x_usb_power: Only poll while offline power: supply: axp20x_usb_power: Add wakeup control power: supply: axp20x_usb_power: Allow offlining power: supply: axp20x_usb_power: Use a match structure power: suppy: ucs1002: Make the symbol 'ucs1002_regulator_enable' static power: reset: at91-poweroff: use proper master clock register offset power: reset: at91-poweroff: introduce struct shdwc_reg_config power: supply: bq25890_charger: Add DT and I2C ids for all supported chips dt-bindings: Add new chips to bq25890 binding documentation power: supply: bq25890_charger: Add support of BQ25892 and BQ25896 chips power: supply: core: Update sysfs-class-power ABI document power: supply: sbs-battery: Fix a signedness bug in sbs_get_battery_capacity() power: supply: ltc2941-battery-gauge: fix use-after-free power: supply: max17040: Correct IRQ wake handling power: supply: axp20x_usb_power: Remove unused device_node power: supply: axp20x_ac_power: Add wakeup control power: supply: axp20x_ac_power: Allow offlining power: supply: axp20x_ac_power: Fix reporting online status ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linuxLinus Torvalds authored
Pull devicetree updates from Rob Herring: - Update dtc to upstream v1.5.1-22-gc40aeb60b47a (plus 1 revert) - Fix for DMA coherent devices on Power - Rework and simplify the DT phandle cache code - DT schema conversions for LEDS, gpio-leds, STM32 dfsdm, STM32 UART, STM32 ROMEM, STM32 watchdog, STM32 DMAs, STM32 mlahb, STM32 RTC, STM32 RCC, STM32 syscon, rs485, Renesas rCar CSI2, Faraday FTIDE010, DWC2, Arm idle-states, Allwinner legacy resets, PRCM and clocks, Allwinner H6 OPP, Allwinner AHCI, Allwinner MBUS, Allwinner A31 CSI, Allwinner h/w codec, Allwinner A10 system ctrl, Allwinner SRAM, Allwinner USB PHY, Renesas CEU, generic PCI host, Arm Versatile PCI - New binding schemas for SATA and PATA controllers, TI and Infineon VR controllers, MAX31730 - New compatible strings for i.MX8QM, WCN3991, renesas,r8a77961-wdt, renesas,etheravb-r8a77961 - Add USB 'super-speed-plus' as a documented speed - Vendor prefixes for broadmobi, calaosystems, kam, and mps - Clean-up the multiple flavors of ST-Ericsson vendor prefixes * tag 'devicetree-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (66 commits) scripts/dtc: Revert "yamltree: Ensure consistent bracketing of properties with phandles" of: Add OF_DMA_DEFAULT_COHERENT & select it on powerpc dt-bindings: leds: Convert gpio-leds to DT schema dt-bindings: leds: Convert common LED binding to schema dt-bindings: PCI: Convert generic host binding to DT schema dt-bindings: PCI: Convert Arm Versatile binding to DT schema dt-bindings: Be explicit about installing deps dt-bindings: stm32: convert dfsdm to json-schema dt-bindings: serial: Convert STM32 UART to json-schema dt-bindings: serial: Convert rs485 bindings to json-schema dt-bindings: timer: Use non-empty ranges in example dt-bindings: arm-boards: typo fix dt-bindings: Add TI and Infineon VR Controllers as trivial devices dt-binding: usb: add "super-speed-plus" dt-bindings: rcar-csi2: Convert bindings to json-schema dt-bindings: iio: adc: ad7606: Fix wrong maxItems value dt-bindings: Convert Faraday FTIDE010 to DT schema dt-bindings: Create DT bindings for PATA controllers dt-bindings: Create DT bindings for SATA controllers dt: bindings: add vendor prefix for Kamstrup A/S ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Various mptcp fixupes from Florian Westphal and Geery Uytterhoeven. 2) Don't clear the node/port GUIDs after we've assigned the correct values to them. From Leon Romanovsky. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: net/core: Do not clear VF index for node/port GUIDs query mptcp: Fix undefined mptcp_handle_ipv6_mapped for modular IPV6 net: drop_monitor: Use kstrdup udp: document udp_rcv_segment special case for looped packets mptcp: MPTCP_HMAC_TEST should depend on MPTCP mptcp: Fix incorrect IPV6 dependency check Revert "MAINTAINERS: mptcp@ mailing list is moderated" mptcp: handle tcp fallback when using syn cookies mptcp: avoid a lockdep splat when mcast group was joined mptcp: fix panic on user pointer access mptcp: defer freeing of cached ext until last moment net: mvneta: fix XDP support if sw bm is used as fallback sch_choke: Use kvcalloc mptcp: Fix build with PROC_FS disabled. MAINTAINERS: mptcp@ mailing list is moderated -
git://git.kernel.org/pub/scm/linux/kernel/git/davem/ideLinus Torvalds authored
Pull IDE updates from David Miller: 1) Fix mem region name in tx4949ide driver, from Christophe JAILLET. 2) Make drive->dn read only, it should not be changeable by users. From Dan Carpenter. 3) Several cast fixups from Krzysztof Kozlowski. There is also going to be a removal of a now unused IDE driver, but that will come via the MIPS tree. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide: ide: make drive->dn read only ide: serverworks: potential overflow in svwks_set_pio_mode() cmd64x: potential buffer overflow in cmd64x_program_timings() ide: remove unneeded header include path to drivers/ide ide: qd65xx: Fix cast to pointer from integer of different size ide: ht6560b: Fix cast to pointer from integer of different size ide: remove set but not used variable 'hwif' ide: remove unnecessary touch_softlockup_watchdog ide: tx4939ide: Fix the name used in a 'devm_request_mem_region()' call ide: Use dev_get_drvdata where possible -
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparcLinus Torvalds authored
Pull sparc updates from David Miller: 1) Add a proper .exit.data section. 2) Fix ipc64_perm type definition, from Arnd Bergmann. 3) Support folded p4d page tables on sparc64, from Mike Rapport. 4) Remove uses of struct timex, also from Arnd Bergmann. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: y2038: sparc: remove use of struct timex sparc64: add support for folded p4d page tables sparc/console: kill off obsolete declarations sparc32: fix struct ipc64_perm type definition sparc32, leon: Stop adding vendor and device id to prom ambapp path components sparc: Add .exit.data section. sparc: remove unneeded uapi/asm/statfs.h
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linuxLinus Torvalds authored
Pull arm64 KVM fix from Catalin Marinas: "Set the correct MDCR_EL2 register value on the first run of a vCPU" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: KVM: arm64: Write arch.mdcr_el2 changes since last vcpu_load on VHE
-
Leon Romanovsky authored
VF numbers were assigned to node_guid and port_guid, but cleared right before such query calls were issued. It caused to return node/port GUIDs of VF index 0 for all VFs. Fixes: 30aad417 ("net/core: Add support for getting VF GUIDs") Reported-by:
Adrian Chiris <adrianc@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
