- 14 Sep, 2012 5 commits
-
-
Greg Kroah-Hartman authored
dbg() was a very old USB-serial-specific macro. This patch removes it from being used in the driver and uses dev_dbg() instead. CC: Johan Hovold <jhovold@gmail.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
dbg() was a very old USB-serial-specific macro. This patch removes it from being used in the driver and uses dev_dbg() instead. CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> CC: "Bjørn Mork" <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
dbg() was a very old USB-serial-specific macro. This patch removes it from being used in the driver and uses dev_dbg() instead. CC: Matthias Bruestle and Harald Welte <support@reiner-sct.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
dbg() was a very old USB-serial-specific macro. This patch removes it from being used in the driver and uses dev_dbg() instead. CC: Johan Hovold <jhovold@gmail.com> CC: Preston Fick <preston.fick@silabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
dbg() was a very old USB-serial-specific macro. This patch removes it from being used in the driver and uses dev_dbg() instead. CC: Johan Hovold <jhovold@gmail.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 13 Sep, 2012 14 commits
-
-
Greg Kroah-Hartman authored
Merge tag 'for-usb-next-2012-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next xHCI patches for 3.7 Hi Greg, Here's seven patches for 3.7. The first four fix an issue with Set Address command timeouts. It turns out that Set Address timeouts can trigger a warning that was put in to avoid a NULL pointer dereference. This patchset fixes the underlying cause of the NULL pointer that was papered over by the warning. They should be applied to stable, but I'm a bit nervous about the size, so I'd rather they go into 3.7, rather than trying to stuff them into a late 3.6-rc. The other three patches are various trivial fixes. Sarah Sharp
-
Greg Kroah-Hartman authored
This cleans up the usb-serial module to remove all old usages of dbg() and "raw" printk() calls for error reporting (there are some info messages left for now.) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Senna Tschudin authored
removes unnecessary semicolon Found by Coccinelle: http://coccinelle.lip6.fr/Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sebastian Andrzej Siewior authored
The comment is a quote of Alan Stern and reflects the data structure better than the the initial comment. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Felipe Balbi authored
drivers/usb/host/xhci.c:1826:14: warning: symbol 'xhci_get_block_size' was not declared. Should it be static? drivers/usb/host/xhci.c:1844:14: warning: symbol 'xhci_get_largest_overhead' was not declared. Should it be static? drivers/usb/host/xhci-ring.c:2304:36: warning: context imbalance in 'handle_tx_event' - unexpected unlock drivers/usb/host/xhci-hub.c:425:6: warning: symbol 'xhci_set_remote_wake_mask' was not declared. Should it be static? Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Elric Fu authored
According to xHCI spec section 4.6.1.1 and section 4.6.1.2, after aborting a command on the command ring, xHC will generate a command completion event with its completion code set to Command Ring Stopped at least. If a command is currently executing at the time of aborting a command, xHC also generate a command completion event with its completion code set to Command Abort. When the command ring is stopped, software may remove, add, or rearrage Command Descriptors. To cancel a command, software will initialize a command descriptor for the cancel command, and add it into a cancel_cmd_list of xhci. When the command ring is stopped, software will find the command trbs described by command descriptors in cancel_cmd_list and modify it to No Op command. If software can't find the matched trbs, we can think it had been finished. This patch should be backported to kernels as old as 3.0, that contain the commit 7ed603ec "xhci: Add an assertion to check for virt_dev=0 bug." That commit papers over a NULL pointer dereference, and this patch fixes the underlying issue that caused the NULL pointer dereference. Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com> Cc: stable@vger.kernel.org
-
Elric Fu authored
The patch is used to cancel command when the command isn't acknowledged and a timeout occurs. This patch should be backported to kernels as old as 3.0, that contain the commit 7ed603ec "xhci: Add an assertion to check for virt_dev=0 bug." That commit papers over a NULL pointer dereference, and this patch fixes the underlying issue that caused the NULL pointer dereference. Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com> Cc: stable@vger.kernel.org
-
Elric Fu authored
Software have to abort command ring and cancel command when a command is failed or hang. Otherwise, the command ring will hang up and can't handle the others. An example of a command that may hang is the Address Device Command, because waiting for a SET_ADDRESS request to be acknowledged by a USB device is outside of the xHC's ability to control. To cancel a command, software will initialize a command descriptor for the cancel command, and add it into a cancel_cmd_list of xhci. Sarah: Fixed missing newline on "Have the command ring been stopped?" debugging statement. This patch should be backported to kernels as old as 3.0, that contain the commit 7ed603ec "xhci: Add an assertion to check for virt_dev=0 bug." That commit papers over a NULL pointer dereference, and this patch fixes the underlying issue that caused the NULL pointer dereference. Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com> Cc: stable@vger.kernel.org
-
Elric Fu authored
Adding cmd_ring_state for command ring. It helps to verify the current command ring state for controlling the command ring operations. This patch should be backported to kernels as old as 3.0. The commit 7ed603ec "xhci: Add an assertion to check for virt_dev=0 bug." papers over the NULL pointer dereference that I now believe is related to a timed out Set Address command. This (and the four patches that follow it) contain the real fix that also allows VIA USB 3.0 hubs to consistently re-enumerate during the plug/unplug stress tests. Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com> Cc: stable@vger.kernel.org
-
Greg Kroah-Hartman authored
These dbg() calls were no more than just a function trace, so remove them. If you want to see the functions being called, use the in-kernel function trace code instead, it's much nicer. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
It's not needed, and commented out, so just remove it. Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
If VERBOSE_DEBUG was enabled, lots of build errors happend (obviously no one uses this mode.) So fix that up, and get rid of the dbg() call, and use dev_dbg() like the rest of the driver does. Cc: Duncan Sands <duncan.sands@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
This adds a driver for the zte_ev set of usb to serial devices. It is based on a patch floating around the internet that modified the generic usb-serial driver to only work for this type of device. I've left comments in the code that I think show the data commands being sent to the device, which I'm guessing come from a usb analyzer. Maybe they can help others out as well. Many thanks to nirinA raseliarison for pointing the original patch out to me, and for testing that the driver works properly. Tested-by: nirinA raseliarison <nirina.raseliarison@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
Now that we have a printk modifier for data streams, use it instead of rolling our own. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 12 Sep, 2012 14 commits
-
-
Richard Zhao authored
- let role driver handle irq before ID change check; this gives the role driver a chance to handle disconnect; - disable irq during switch role; no role driver to handle irq in the period. Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Richard Zhao authored
This patch turns on debugging output if CONFIG_USB_CHIPIDEA_DEBUG is enabled. Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Richard Zhao authored
Using vbus valid interrupt to detect vbus. Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Richard Zhao authored
In order to avoid re-queueing of the role changing work, we need to clear the ID change interrupt bit right in the irq handler. Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Richard Zhao authored
The ID pin needs 1ms debounce time, even at probe time. We delay 2ms to be on the safe side. Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Richard Zhao authored
Some controllers may not need to setup pinctrl, so we don't fail the probe if pinctrl get/select failed. Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Richard Zhao authored
i.MX usb controllers share non-core registers, which may include SoC specific controls. We turn it into a usbmisc device and usbmisc driver set operations needed by ci13xxx_imx driver. For example, Sabrelite board has bad over-current design, we can usbmisc to disable over-current detection. Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
These chipidea stable patches are needed for other chipidea patches to be applied properly. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michael Grzeschik authored
When attaching an imx28 or imx53 in USB gadget mode to a Windows host and starting a rndis connection we see this message every 4-10 seconds: g_ether gadget: high speed config #2: RNDIS Analysis shows that each time this message is printed, the rndis connection is re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The endpoint is stalled because the reqeust complete bit on that endpoint is set, but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is empty. This patch removed this check, because the code doesn't take the following situation into account: The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed and completed here. There seems to be a race condition, the request is nuked, but the request complete bit will be set, too. The subsequent check (in ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will fail. Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't have this check. Cc: stable <stable@vger.kernel.org> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marc Kleine-Budde authored
If udc_start() fails the qh_pool dma-pool cannot be closed because it's still in use. This patch factors out the dma_pool_free() loop into destroy_eps() and calls it in the error path of udc_start(), too. Cc: stable <stable@vger.kernel.org> Reviewed-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marc Kleine-Budde authored
This patch fixes the error path of udc_start(). Now NULL is used to unset the peripheral with otg_set_peripheral(). Cc: stable <stable@vger.kernel.org> Reviewed-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michael Grzeschik authored
Add function to physicaly enable or disable of pullup connection on the USB-D+ line. The uvc gaget will fail, if this function is not implemented. Cc: stable <stable@vger.kernel.org> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michael Grzeschik authored
This patch changes the setup of the endpoint maxpacket size. All non control endpoints are initialized with an undefined ((unsigned short)~0) maxpacket size. The maxpacket size of Endpoint 0 will be kept at CTRL_PAYLOAD_MAX. Some gadget drivers check for the maxpacket size before they enable the endpoint, which leads to a wrong state in these drivers. Cc: stable <stable@vger.kernel.org> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Commit ff823c79 ("usb: move children to struct usb_port") forgot to consider the hub_disconnect sequence, which releases ports before quiescing the hub, which will lead to a use-after-free, since hub_quiesce() will try to disconnect ports' children, which are already deallocated. Simple modprobe dummy_hcd && rmmod dummy_hcd will illustrate the problem. This patch moves deallocation of hub's ports after hub_quiesce() call in hub_disconnect(). Cc: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 11 Sep, 2012 7 commits
-
-
Kuninori Morimoto authored
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usbGreg Kroah-Hartman authored
usb: musb: patches for v3.7 merge window Here we have a bunch of miscellaneous cleanups and fixes to the musb driver. It fixes a bunch of mistakes errors which nobody has triggered before, so I'm not Ccing stable tree. We are finally improving OMAP's VBUS/ID Mailbox usage so that we can introduce our PHY drivers properly. Also, we're adding support for multiple instances of the MUSB IP in the same SoC, as seen on some platforms from TI which have 2 MUSB instances. Other than that, we have some small fixes like not kicking DMA for a zero byte transfer, or properly handling NAK timeout on MUSB's host side, and the enabling of DMA Mode1 for any transfers which are aligned to wMaxPacketSize. All patches have been pending on mailing list for a long time and I don't expect any big surprises with this pull request.
-
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usbGreg Kroah-Hartman authored
usb: dwc3: patches for v3.7 merge window Some much needed changes for our dwc3 driver. First there's a rework on the ep0 handling due to some Silicon issue we uncovered which affects all users of this IP core (there's a missing XferNotReady(DATA) event in some conditions). This issue which show up as a SETUP transfers which wouldn't complete ever and we would fail TD 7.06 of the Link Layer Test from USB-IF and Lecroy's USB3 Exerciser. We also fix a long standing bug regarding EP0 enable sequencing where we weren't setting a particular bit (Ignore Sequence Number). Since we never saw any problems caused by that, it didn't deserve being sent to stable tree. On this pull request we also fix Burst Size initialization which should be done only in SuperSpeed and we were mistakenly setting Burst Size to the maximum value on non-SuperSpeed mode. Again, since we never saw any problems caused by that, we're not sending this patch to stable. There's also a memory ordering fix regarding usage of bitmaps in dwc3 driver. You will also find some sparse warnings fix, a fix for missed isochronous packets when the endpoint is already busy, and a fix for synchronization delay on dwc3_stop_active_transfer().
-
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usbGreg Kroah-Hartman authored
usb: xceiv: patches for v3.7 merge window nop xceiv got its own header to avoid polluting otg.h. It has also learned to work as USB2 and USB3 phys so we can use it on USB3 controllers. Together with those two changes to nop xceiv, we're adding basic PHY support to dwc3 driver, this is to allow platforms which actually have a SW-controllable PHY talk to them through dwc3 driver. We're adding a new phy driver for the OMAP architecture. This driver is for the PHY found in OMAP4 SoCs, and a new phy driver for the marvell architecture. An extra phy driver - for Tegra SoCs - is now moving from arch/arm/mach-tegra* to drivers/usb/phy. Also here, there's the creation of <linux/usb/phy.h> which should be used from now on for PHY drivers, even those which don't support OTG.
-
Greg Kroah-Hartman authored
Merge tag 'gadget-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next usb: gadget: patches for v3.7 merge window This pull request is large but the biggest part is the first part of the cleanup on the gadget framework so we have a saner setup to add configfs support for v3.8. We have also some more conversions to the new udc_start/udc_stop which makes us closer from dropping the old interfaces. USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED are finally gone, thanks to Michal for his awesome work. Other than that, we have the usual set of miscellaneous changes and cleanups involving improvements to debug messages, removal of duplicated includes, moving dereference after NULL test, making renesas_hsbhs' irq handler Shared, unused code being dropped, prevention of sleep-inside-spinlock bugs and a race condition fix on udc-core.
-
Ajay Kumar Gupta authored
As NOP device node is now added in am33xx tree so remove the call which creates the NOP platform_device. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com> Signed-off-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
-
Ajay Kumar Gupta authored
Added device tree support for dsps musb glue driver and updated the Documentation with device tree binding information. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com> Signed-off-by: Ravi Babu <ravibabu@ti.com> [afzal@ti.com: use '-' instead of '_' for dt properties] Signed-off-by: Afzal Mohammed <afzal@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
-