The request to create an mccq was being dispatched without
doing a byte swap of num_pages. This byte swap is necessary
for Big Endian systems like PPC. Not having this fix leads
mccq create to fail on BE ASICs running newer version of
firmware, thereby causing driver initialization failure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Migrate from the legacy PM hooks to use dev_pm_ops structure.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The davinci emac driver uses some ARM specific DMA APIs
for cache coherency which have been removed from kernel
with the 2.6.34 merge.

Modify the driver to use the dma_{map, unmap}_single() APIs
defined in dma-mapping.h

Without this fix, the driver fails to compile on Linus's
tree.

Tested on DM365 and OMAP-L138 EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the PCI pool changes were added to fix resume failures:

commit 98468efd
e100: Use pci pool to work around GFP_ATOMIC order 5 memory allocation failu

and

commit 70abc8cb
e100: Fix broken cbs accounting due to missing memset.

This introduced a problem that can happen if the TX ring size
is increased.  We need to size the PCI pool using cbs->max
instead of the default cbs->count value.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On Wed, 2010-03-10 at 08:41 -0800, David Miller wrote:
> From: Mikael Pettersson <mikpe@it.uu.se>
> Date: Wed, 10 Mar 2010 16:33:28 +0100
> > Booting 2.6.34-rc1 on a machine with a tulip nic I see
> > a number of kernel messages that include "(null)" where
> > previous kernels included the string "tulip0":
> CC:'ing the guilty party :-)  It's one of the following
> commits:

Thanks Mikael.

Anonymity has some good attributes.
Blame avoidance is one of them.

I've broad shoulders.  It's me, then Dwight Howard...

There might be another few of these where ->name or ->dev
was used before struct device or net_device was registered.
I'll go back and check.

tulip_core has:

	if (tp->flags & HAS_MEDIA_TABLE) {
		sprintf(dev->name, DRV_NAME "%d", board_idx);	/* hack */
		tulip_parse_eeprom(dev);
		strcpy(dev->name, "eth%d");			/* un-hack */
	}

So I don't feel _too_ bad.

tulip_parse_eeprom is done before register_netdev so the logging
there can not use netdev_<level> or dev_<level>(&dev->dev
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure we always call rtnl_lock before going down the
error path in sky2_resume, which unlocks the rtnl lock.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we are managing IPv6 addresses using DHCP, it would be nice
for user-space to be notified if an address configured through
DHCP fails DAD.  Otherwise user-space would have to poll to see
whether DAD succeeds.

This patch uses the existing notification mechanism and simply
hooks it into the DAD failure code path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The constant TG3_FLAG_10_100_ONLY should be used with the tg3_flags field,
not the tg3_flags2 field, as done elsewhere in the same file.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some network devices, particularly USB ones, take several seconds to
fully init and appear in the device list.

If the user turned ipconfig on, they are using it for NFS root or some
other early booting purpose.  So it makes no sense to just flat out
fail immediately if the device isn't found.

It also doesn't make sense to just jack up the initial wait to
something crazy like 10 seconds.

Instead, poll immediately, and then periodically once a second,
waiting for a usable device to appear.  Fail after 12 seconds.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Christian Pellegrin <chripell@fsfe.org>

Fix memory leak and use kmalloc() instead of kzalloc() as we are going
to overwrite the allocated buffer.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently hardware with !IEEE80211_HW_PS_NULLFUNC_STACK and
IEEE80211_HW_REPORTS_TX_ACK_STATUS will never enter PSM due to the
conditions in the power save entry functions.

Fix those conditions.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixed below compiler warning:

drivers/net/wireless/ipw2x00/ipw2200.c: In function ‘ipw_load_firmware’:
drivers/net/wireless/ipw2x00/ipw2200.c:3260: warning: the frame size of
1168 bytes is larger than 1024 bytes
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

we read the IQ correction values (i_cal and q_cal) for G mode from a wrong
location (the same shifts as for A mode is applied which is incorrect). use
correct locations, matching the docs and HAL sources.

also we should write IQ correction only when we have that information in the
EEPROM, starting from version 4. also write it in the same way as we do in the
periodic recalibration (enable last), just to be sure.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I/Q calibration was completely broken, resulting in a high number of CRC errors
on received packets. before i could see around 10% to 20% CRC errors, with this
patch they are between 0% and 3%.

1.) the removal of the mask in commit "ath5k: Fix I/Q calibration
(f1cf2dbd)" resulted in no mask beeing used
when writing the I/Q values into the register. additional errors in the
calculation of the values (see 2.) resulted too high numbers, exceeding the
masks, so wrong values like 0xfffffffe were written. to be safe we should
always use the bitmask when writing parts of a register.

2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we
convert to a signed value later by substracting 128. this resulted in too low
numbers for Q many times, which were limited to -16 by the boundary check later
on.

3.) checked everything against the HAL sources and took over comments and minor
optimizations from there.

4.) we can't use ENABLE_BITS when we want to write a number (the number can
contain zeros). also always write the correction values first and set ENABLE
bit last, like the HAL does.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: stable@kernel.org
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

to reset the TSF, AR5K_BEACON_RESET_TSF has to be 1, not 0. also we have a
function for that so use it.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

when using a fixed antenna we should use the antenna number in all tx
descriptors, otherwise the hardware will sometimes send the frame out on the
other antenna. it seems like the hardware does not always respect the default
antenna and diversity settings (esp.  AR5K_STA_ID1_DEFAULT_ANTENNA).

also i would like to note that antenna diversity does not always work correctly
on 5414 (at least) when only one antenna is connected: for example all frames
might be received on antenna A but still the HW tries to send on antenna B some
times, causing packet loss.

this is both verified with the antenna statistics output of the previous patch
and a spectrum analyzer.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ieee->networks consists of 128 struct libipw_network entries. If
we allocate this chunk of memory altogether, it ends up with an
order 4 page allocation. High order page allocation is likely to fail
on system high load. This patch splits the big chunk memory allocation
into small pieces, each is 344 bytes, allocates them with 128 times.

The patch fixed bug http://bugzilla.kernel.org/show_bug.cgi?id=14989Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 34e89507 introduced sta_mtx
locking into sta_info_insert() (now sta_info_insert_rcu), but forgot
to unlock this mutex on one of the error paths. Fix this by adding
the missing mutex_unlock() call for the case where STA insert fails
due to an entry existing already. This may happen at least in AP mode
when a STA roams between two BSSes (vifs).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove the KSEG1ADDR define from rt2x00soc.h as it redefines and covers the
correct one from the arch/mips/include/asm/addrspace.h. Otherwise the driver
oopses on the target platform (Ralink rt3050 board).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some embedded ColdFire based boards use the SMC 91x family of ethernet
devices. (For example the Freescale M5249C3 and MoretonBay NETtel).

Add IO access support to the SMC91x driver, and allow this driver to
be configured for ColdFire platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting new MAC address only worked when device was set to promiscuous mode.
Fix MAC address by writing new address to device using undocumented command
AX_CMD_READ_NODE_ID+1. Patch is tested with AX88772 device.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a43912ab... ("tunnel: eliminate recursion field") eliminated
use of recursion field from tunnel structures, but its definition
still exists in ip6_tnl{}.

Let's remove that unused field.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 6e17d45a (net: add addr len check to dev_mc_add)
added a bug in dev_mc_add(), since it can now exit with a lock
imbalance.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Annotates neigh_invalidate() with __releases() and __acquires() for
sparse sake.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit d218d111 (tcp: Generalized TTL Security Mechanism) added a bug
for TIMEWAIT sockets. We should not test min_ttl for TW sockets.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 09943a18
	Author: Matt Carlson <mcarlson@broadcom.com>
	Date:   Fri Aug 28 14:01:57 2009 +0000

	tg3: Convert ISR parameter to tnapi

forgot to update tg3_poll_controller(), leading to intermittent crashes with
netpoll.

Fix this.
Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Deactivate inbound checksumming on HiperSocket is a valid but
dangerous optimization in case the frame is routed from an OSA
network to an HiperSockets network. To go for sure we change the
default to software checksumming.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Depending on their definition in z/VM, virtual devices for z/VM
VSWITCH or GuestLAN must be configured either in layer2 or in
layer3 mode. If qeth detects a layer mismatch, device activation
fails. Trying to recover from this error cannot help; thus
scheduling a recovery should be avoided.
In addition, since recovery is forbidden during online setting of
a qeth device, existence of its network device is guaranteed for all
dev_close() calls in qeth. The corresponding checks can be removed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If HiperSockets Network Traffic Analyzer is switched off, but trace
disabling fails somehow, the qeth driver does not switch off its
promisc mode status. A following sniffer reactivation fails, since
qeth does not see a need to reenable tracing.
At the same time the code analyzing results of trace commands is
restructured.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dhcp frames are valid IPv4 packets so there is no need to send them
in pass thru mode. This allows dhcp packets to pass HiperSockets.
Also the dhcp release frame is send out correctly with this patch.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

provide qeth kmsg definitions to enable hash string generation for
kernel message created with dev_err().
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 21b2d8bd.

As explained by Johannes:
When we
build a probe request frame in the buffer with the SSID, we could
arrive over the limit of 200 bytes. When we build it in the buffer
without the SSID (wildcard) we don't arrive over 200 bytes, but the
ucode still allows direct probe in addition because it has an internal
buffer that is larger when it inserts the SSID...
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Recent patch "iwlwifi: move 3945 clip groups to 3945 data" exposed a memory
corruption problem. When initializing the clip groups the code was
mistakenly using the iwlagn rate count, not the 3945 rate count. This
resulted in more memory being written than was allocated.

"iwlwifi: move 3945 clip groups to 3945 data" moved the location where the
clip groups are stored and the impact is now severe in that the number of
configured TX queues is modified. Previously the
"temperature" field was overwritten, which did not seem to affect the
operation.

Fix this one instance where wrong rate count was used. I also noticed one
more location where the iwlagn rate count was used to index an iwl3945
array, fix this. I also modified one location that modified the iwlagn rate
count to obtain the iwl3945 rate count ... just use the iwl3945 rate count
directly.

This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2165 and
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2168Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Port commit 20deb48d16fdd07ce2fdc8d03ea317362217e085
from git://tipc.cslab.ericsson.net/pub/git/people/allan/tipc.git

Part of the large effort I'm trying to help with getting all the downstreamed
code from windriver forward ported to the upstream tree

Origional commit message
Restore check to filter out inadverdently received messages
This patch reimplements a check that allows TIPC to discard messages
that are not intended for it.  This check was present in TIPC 1.5/1.6,
but was removed by accident during the development of TIPC 1.7; it has
now been updated to account for new features present in TIPC 1.7 and
reinserted into TIPC.  The main benefit of this check is to filter
out messages arriving from orphaned link endpoints, which can arise
when a node exits the network and then re-enters it with a different
TIPC network address (i.e. <Z.C.N> value).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Origionally-authored-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove htohl implementation from tipc

I was working on forward porting the downstream commits for TIPC and ran accross this one:
http://tipc.cslab.ericsson.net/cgi-bin/gitweb.cgi?p=people/allan/tipc.git;a=commitdiff;h=894279b9437b63cbb02405ad5b8e033b51e4e31e

I was going to just take it, when I looked closer and noted what it was doing.
This is basically a routine to byte swap fields of data in sent/received packets
for tipc, dependent upon the receivers guessed endianness of the peer when a
connection is established.  Asside from just seeming silly to me, it appears to
violate the latest RFC draft for tipc:
http://tipc.sourceforge.net/doc/draft-spec-tipc-02.txt
Which, according to section 4.2 and 4.3.3, requires that all fields of all
commands be sent in network byte order.  So instead of just taking this patch,
instead I'm removing the htohl function and replacing the calls with calls to
ntohl in the rx path and htonl in the send path.

As part of this fix, I'm also changing the subscr_cancel function, which
searches the list of subscribers, using a memcmp of the entire subscriber list,
for the entry to tear down.  unfortunately it memcmps the entire tipc_subscr
structure which has several bits that are private to the local side, so nothing
will ever match.  section 5.2 of the draft spec indicates the <type,upper,lower>
tuple should uniquely identify a subscriber, so convert subscr_cancel to just
match on those fields (properly endian swapped).

I've tested this using the tipc test suite, and its passed without issue.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use self documenting noinline_for_stack instead of duplicated comments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>