Bindings require pin configuration nodes to have the function, even if
it is GPIO:

  msm8916-thwc-ufi001c.dtb: pinctrl@1000000: sim-ctrl-default-state: 'oneOf' conditional failed, one must be fixed:
    'esim-sel-pins', 'sim-en-pins', 'sim-sel-pins' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324202244.744271-1-krzysztof.kozlowski@linaro.org

Add support for UFS ICE by adding the qcom,ice property and the
ICE dedicated devicetree node.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407105029.2274111-7-abel.vesa@linaro.org

Add nodes for remoteproc, smp2p and smsm in preparation
for audio support on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-4-a39.skl@gmail.com

Add nodes for remoteproc, smp2p and smsm to make it possible to use
modem functionality on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-3-a39.skl@gmail.com

Add nodes for remoteproc, smp2p and smsm to make it possible to use
wifi/bt functionality on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-2-a39.skl@gmail.com

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-2-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-1-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.

Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180045.126952-1-krzysztof.kozlowski@linaro.org

Fix typo in drive-strength property name.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180710.128815-1-krzysztof.kozlowski@linaro.org

Fix typo in drive-strength property name.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407181541.139349-1-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-10-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-9-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-8-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-7-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-6-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-5-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-4-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-3-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-2-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-1-krzysztof.kozlowski@linaro.org

Add support for the Xiaomi Mi A3 (xiaomi-laurel-sprout). Here's a
summary on what's defined.

- dmesg output to bootloader preconfigured display
- USB
- UFS
- SD card
- SMD RPM regulators
- Volume Up, Down and Power buttons
- Thermistors
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306170817.3806-7-they@mint.lgbt

Adds a UFS host controller node and its corresponding PHY to
the sm6125 platform.
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306170817.3806-5-they@mint.lgbt

Add support for the Xiaomi Mi Pad 5 Pro CSOT variant. The CSOT variant
uses China Star Optoelectronics Technology (CSOT) panel based on NT36523
display controller.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-3-lujianhua000@gmail.com

Add nodes for BOE NT36523 panel found in xiaomi-elish. This panel
is a dual dsi mode panel and the dsi phy type is cphy.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-2-lujianhua000@gmail.com

There are two panel variants of xiaomi-elish, BOE and CSOT panels.
In order to support both panels, so split elish dts into common dtsi
and elish-boe dts.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-1-lujianhua000@gmail.com

SC8150 mailbox is compatible with SDM845.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-12-krzysztof.kozlowski@linaro.org

SC7180 mailbox is compatible with SDM845.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-11-krzysztof.kozlowski@linaro.org

QCS404 mailbox is compatible with MSM8916.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-10-krzysztof.kozlowski@linaro.org

SM6125 mailbox is compatible with MSM8994.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-9-krzysztof.kozlowski@linaro.org

SM6115 mailbox is compatible with MSM8994.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-8-krzysztof.kozlowski@linaro.org

SDM630 mailbox is compatible with MSM8994.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-7-krzysztof.kozlowski@linaro.org

MSM8998 mailbox is compatible with MSM8994.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-6-krzysztof.kozlowski@linaro.org

MSM8976 mailbox is compatible with MSM8994.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-5-krzysztof.kozlowski@linaro.org

IPQ8074 mailbox is compatible with IPQ6018.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-4-krzysztof.kozlowski@linaro.org

Add an initial device tree for the QTI RB1 development board, based on
the QRB2210 (QCM2290 derivative) SoC. This device tree targets the SoM
revision 4, a.k.a. the Mass Production SKU.

To get a successful boot, run:

cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/qrb2210-rb1.dtb >\
.Image.gz-dtb

mkbootimg \
--kernel .Image.gz-dtb \
--ramdisk some_initrd \
--output rb1-boot.img \
--pagesize 4096 \
--base 0x8000 \
--cmdline 'some cmdline'

fastboot boot rb1-boot.img

There's no dtbo or other craziness to worry about.
For the best dev experience, you can erase boot and use fastboot boot
everytime, so that the bootloader doesn't mess with you.

If you have a SoM revision 3 or older (there should be a sticker on it
with text like -r00, where r is the revision), you will need to apply
this additional diff:

aliases {
-   serial0 = &uart0;
+   serial0 = &uart4;

/* UART connected to the Micro-USB port via a FTDI chip */
-   &uart0 {
+   &uart4 {

That should however only concern preproduction boards.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v2-5-dae06f8830dc@linaro.org

Introduce an initial device tree for the PM2250 (sometimes known as
PM4125) PMIC.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v2-4-dae06f8830dc@linaro.org

Add an initial device tree for the QCM2290 low-end SoC, featuring 4
"customized" Cortex-A53 cores and up to 4 GiB of LPDDR(3/4X).

This revision brings support for:
- TSENS & thermal zones
- SDHCI1/2
- I2C, SPI, UART
- MPSS
- ADSP
- Wi-Fi
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v2-3-dae06f8830dc@linaro.org

Drop the qcom,snoc-host-cap-skip-quirk that was never introduced to
solve schema warnings.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406-topic-ath10k_bindings-v3-2-00895afc7764@linaro.org

Enable the SLPI DSP on the SHIFTPHONES SHIFT6mq phone with a
Qualcomm SDM845 SoC.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-6-me@dylanvanassche.be

Enable the SLPI DSP on the Oneplus 6 phone with a Qualcomm SDM845 SoC.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-5-me@dylanvanassche.be