Goal is to be able to use __tpacket_has_room() without holding a lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct packet_sock  is only read.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit "net: phy: Add detection of 1000BaseX link mode support" added
support for not filtering out 1000BaseX mode from the PHY's supported
modes in genphy_config_init, but we have to make a similar change in
genphy_read_abilities in order to actually detect it as a supported mode
in the first place. Add this in.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only for consistency reasons, do it like in main cpsw.c module
and use ndev reference but not by means of slave.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to set ndev for drvdata when mainly cpsw reference is needed,
so correct this legacy decision.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
net/mlx5: use indirect call wrappers

The mlx5_core driver uses several indirect calls in fast-path, some of them
are invoked on each ingress packet, even for the XDP-only traffic.

This series leverage the indirect call wrappers infrastructure the avoid
the expansive RETPOLINE overhead for 2 indirect calls in fast-path.

Each call is addressed on a different patch, plus we need to introduce a couple
of additional helpers to cope with the higher number of possible direct-call
alternatives.

v2 -> v3:
 - do not add more INDIRECT_CALL_* macros
 - use only the direct calls always available regardless of
   the mlx5 build options in the last patch

v1 -> v2:
 - update the direct call list and use a macro to define it,
   as per Saeed suggestion. An intermediated additional
   macro is needed to allow arg list expansion
 - patch 2/3 is unchanged, as the generated code looks better this way than
   with possible alternative (dropping BP hits)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We can avoid another indirect call per packet wrapping the rx
handler call with the proper helper.

To ensure that even the last listed direct call experience
measurable gain, despite the additional conditionals we must
traverse before reaching it, I tested reversing the order of the
listed options, with performance differences below noise level.

Together with the previous indirect call patch, this gives
~6% performance improvement in raw UDP tput.

v2 -> v3:
 - use only the direct calls always available regardless of
   the mlx5 build options
 - drop the direct call list macro, to keep the code as simple
   as possible for future rework

v1 -> v2:
 - update the direct call list and use a macro to define it,
   as per Saeed suggestion. An intermediated additional
   macro is needed to allow arg list expansion
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can avoid an indirect call per packet wrapping the skb creation
with the appropriate helper.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Many changes all over:
 * HE (802.11ax) work continues
 * WPA3 offloads
 * work on extended key ID handling continues
 * fixes to honour AP supported rates with auth/assoc frames
 * nl80211 netlink policy improvements to fix some issues
   with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use extack error reporting mechanism in addition to returning -EINVAL

NL_SET_ERR_* code shamelessy copy/paste/adjusted from act_pedit &
sch_cake and used as reference as to what I should have done in the
first place.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Also, there is no need to store the individual debugfs file name, just
remove the whole directory all at once, saving a local variable.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guillaume Nault <g.nault@alphalink.fr>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: add and use helper rtl_is_8168evl_up

Few registers have been added or changed its purpose with version
RTL8168e-vl, so create a helper for identifying chip versions from
RTL8168e-vl.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

>From RTL8168e-vl the value in register MaxTxPacketSize is interpreted
differently, therefore use new helper rtl_is_8168evl_up to set this
register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helper rtl_is_8168evl_up to make the code better readable and to
simplify it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the offchannel TX wait time expires, send the appropriate event.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211_remain_on_channel_expired is used to notify userspace when
the remain on channel duration expired by sending an event. There is
no such equivalent to CMD_FRAME, where if offchannel and a duration
is provided, the card will go offchannel for that duration. Currently
there is no way for userspace to tell when that duration expired
apart from setting an independent timeout. This timeout is quite
erroneous as the kernel may not immediately send out the frame
because of scheduling or work queue delays. In testing, it was found
this timeout had to be quite large to accomidate any potential delays.

A better solution is to have the kernel send an event when this
duration has expired. There is already NL80211_CMD_FRAME_WAIT_CANCEL
which can be used to cancel a NL80211_CMD_FRAME offchannel. Using this
command matches perfectly to how NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL
works, where its both used to cancel and notify if the duration has
expired.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This appears to happen occasionally, and if it does we
really want even more information than we have now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If HW advertises it has rate control, we skip all of the
rate control assignments, but sometimes the data we have
here is useful, especially so that we don't have to do
the lookups again on which rates are configured and are
supported.

So do the low rate assignment anyway to help out drivers
that might need it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Even if we have a station, we currently call rate_control_send_low()
with the NULL station unless further rate control (driver, minstrel)
has been initialized.

Change this so we can use more information about the station to use
a better rate. For example, when we associate with an AP, we will
now use the lowest rate it advertised as supported (that we can)
rather than the lowest mandatory rate. This aligns our behaviour
with most other 802.11 implementations.

To make this possible, we need to also ensure that we have non-zero
rates at all times, so in case we really have *nothing* pre-fill
the supp_rates bitmap with the very lowest mandatory bitmap (11b
and 11a on 2.4 and 5 GHz respectively).

Additionally, hostapd appears to be giving us an empty supported
rates bitmap (it can and should do better, since the STA must have
supported for at least the basic rates in the BSS), so ignore any
such bitmaps that would actually zero out the supp_rates, and in
that case just keep the pre-filled mandatory rates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add the "OBSS Narrow Bandwidth RU In OFDMA Tolerance Support" flag
definition to the definitions of the flags covered by the Extended
Capability IE.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a function that iterates over the BSS entries associated with a
given wiphy and calls a callback for each iterated BSS. This can be
used by drivers in various ways, e.g., to evaluate some property for
all the BSSs in the medium.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Allow the userland daemon to en/disable TWT support for an AP.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
[simplify parsing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Turn TWT for STA interfaces when they associate and/or receive a
beacon where the twt_responder bit has changed.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Require that each vendor command give a policy of its sub-attributes
in NL80211_ATTR_VENDOR_DATA, and then (stricly) check the contents,
including the NLA_F_NESTED flag that we couldn't check on the outer
layer because there we don't know yet.

It is possible to use VENDOR_CMD_RAW_DATA for raw data, but then no
nested data can be given (NLA_F_NESTED flag must be clear) and the
data is just passed as is to the command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This function is similar to ieee80211_get_he_sta_cap() but allows passing
the iftype. Also make ieee80211_get_he_sta_cap() use the new helper
rather than duplicating the code.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Let drivers advertise support for station-mode SAE authentication
offload with a new NL80211_EXT_FEATURE_SAE_OFFLOAD flag.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add definition of WPA version 3 for SAE authentication.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add NL80211_ATTR_IFINDEX attribute to port authorized event to indicate
the operating interface of the device. Also put NL80211_ATTR_WIPHY
attribute in it to be consistent with the other MLME notifications.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

IEEE 802.11 - 2016 forbids mixing MPDUs with different keyIDs in one
A-MPDU. Drivers supporting A-MPDUs and Extended Key ID must actively
enforce that requirement due to the available two unicast keyIDs.

Allow driver to signal mac80211 that they will not check the keyID in
MPDUs when aggregating them and that they expect mac80211 to stop Tx
aggregation when rekeying a connection using Extended Key ID.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

tp->coalesce_info is used in rtl_coalesce_info() only, so we can
remove this member. In addition replace phy_ethtool_get_link_ksettings
with a direct access to tp->phydev->speed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of a timeout currently ~0 is returned. Callers often just check
whether a certain bit is set and therefore may behave incorrectly.
So let's return -ETIMEDOUT in case of a timeout.

r8168_phy_ocp_read is used in r8168g_mdio_read only, therefore we can
apply the same change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The packing facility is needed to decode Ethernet meta frames containing
source port and RX timestamping information.

The DSA driver selects CONFIG_PACKING, but the tagger did not, and since
taggers can be now compiled as modules independently from the drivers
themselves, this is an issue now, as CONFIG_PACKING is disabled by
default on all architectures.

Fixes: e53e18a6 ("net: dsa: sja1105: Receive and decode meta frames")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>

We were accessing the pointer returned from platform_get_resource before
checking if it was valid, causing an oops if it was not. Move this access
after the call to devm_ioremap_resource which does the validity check.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2019-06-11

please apply the following patch series for qeth to net-next.
This brings all sorts of cleanups and minor improvements,
primarily for the control IO path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We statically allocate 8 cmd buffers on the read channel, when the only
IO left that's still using them is the long-running READ.
Replace this with a single allocated cmd, that gets restarted whenever
the READ completed.

This introduces refcounting for allocated cmds, so that the READ cmd can
survive the IO completion.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current IDX sequence first sends one WRITE cmd to activate the
device, and then sends a second cmd that READs the response.

Using qeth_alloc_cmd(), we can combine this into a single IO with two
command-chained CCWs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RCD code is the last remaining IO path that doesn't use the
qeth_send_control_data() infrastructure. Doing so allows us to remove
all sorts of custom state machinery and logic in the IRQ handler.

Instead of introducing statically allocated cmd buffers for this single
IO on the data channel, use the new qeth_alloc_cmd() helper.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth currently uses a fixed set of statically allocated cmd buffers for
the read and write IO channels. This (1) doesn't play well with the single
RCD cmd we need to issue on the data channel, (2) doesn't provide the
necessary flexibility for certain IDX improvements, and (3) is also rather
wasteful since the buffers are idle most of the time.

Add a new type of cmd buffer that is dynamically allocated, and keeps
its ccw chain in the DMA data area. Since this touches most callers of
qeth_setup_ccw(), also add a new CCW flags parameter for future usage.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>