- 17 Dec, 2009 3 commits
-
-
Antonio Ospite authored
This driver provides an interface for controlling LEDs (or vibrators) connected to PMICs for which there is a regulator framework driver. This driver can be used, for instance, to control vibrator on all Motorola EZX phones using the pcap-regulator driver services. Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
-
H Hartley Sweeten authored
Use resource_size() for ioremap. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
-
H Hartley Sweeten authored
Use resource_size() for ioremap. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
-
- 16 Dec, 2009 5 commits
-
-
Michael Hennerich authored
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
-
Daniel Mack authored
The LT3593 is a step-up DC/DC converter designed to drive up to ten white LEDs in series. The current flow can be set with a control pin. This driver controls any number of such devices connected on generic GPIOs and exports the function as as platform_driver. The gpio_led platform data struct definition is reused for this purpose. Successfully tested on a PXA embedded board. Signed-off-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
-
Dave Hansen authored
pci_enable_result is defined using the __must_check macro but leds-ss4200 is not checking the return value. Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com> Signed-off-by: Dave Hansen <dave@sr71.net> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
-
Daniel Mack authored
This makes the LEDs driver for ALIX2.C boards work with Coreboot by looking up the port address in the MSR rather than hard-coding it. The BIOS scan also needed some tweaks as the string in Coreboot differs from the one in the legacy BIOS. Successfully tested with both the legacy tinyBIOS as well as Coreboot v3. Signed-off-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
-
Dave Hansen authored
This code is based on a driver that came in the "Open-source and GPL components" download here: http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Server+Products&ProductLine=Intel%C2%AE+Storage+Systems&ProductProduct=Intel%C2%AE+Entry+Storage+System+SS4200-E&OSVersion=OS+Independent It was in a file called nasgpio.c inside of a second zip file called SS4200-E_Linux_SIO_Driver-v1.4.zip and is based on this updated to use the LED subsystem with the ioctl and hardware monitor support removed. I don't have any need for brightness control, and its code is *completely* separate from the on/off controls implemented here. If anyone else wants it, I'd be happy to look into adding it, but I don't care enough for now. Except for the probe routines, I rewrote most of it. I also Note that I don't have any hardware documentation except for the original driver. Thanks go to Arjan for his help in getting the original source for this released and for chasing down some licensing issues. Signed-off-by: Dave Hansen <dave@sr71.net> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
-
- 15 Dec, 2009 32 commits
-
-
Stephen Rothwell authored
Caused by commit 0b83ddeb ("MFD: twl4030: add twl4030_codec MFD as a new child to the core") interacting with commit b07682b6 ("mfd: Rename twl4030* driver files to enable re-use"). This file seems to have been missed in the renaming. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://oss.sgi.com/xfs/xfsLinus Torvalds authored
* 'for-linus' of git://oss.sgi.com/xfs/xfs: xfs: event tracing support xfs: change the xfs_iext_insert / xfs_iext_remove xfs: cleanup bmap extent state macros
-
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dmLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (80 commits) dm snapshot: use merge origin if snapshot invalid dm snapshot: report merge failure in status dm snapshot: merge consecutive chunks together dm snapshot: trigger exceptions in remaining snapshots during merge dm snapshot: delay merging a chunk until writes to it complete dm snapshot: queue writes to chunks being merged dm snapshot: add merging dm snapshot: permit only one merge at once dm snapshot: support barriers in snapshot merge target dm snapshot: avoid allocating exceptions in merge dm snapshot: rework writing to origin dm snapshot: add merge target dm exception store: add merge specific methods dm snapshot: create function for chunk_is_tracked wait dm snapshot: make bio optional in __origin_write dm mpath: reject messages when device is suspended dm: export suspended state to targets dm: rename dm_suspended to dm_suspended_md dm: swap target postsuspend call and setting suspended flag dm crypt: add plain64 iv ...
-
git://git.kernel.dk/linux-2.6-blockLinus Torvalds authored
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: cfq: set workload as expired if it doesn't have any slice left Fix a CFQ crash in "for-2.6.33" branch of block tree cfq: Remove wait_request flag when idle time is being deleted cfq-iosched: commenting non-obvious initialization cfq-iosched: Take care of corner cases of group losing share due to deletion cfq-iosched: Get rid of cfqq wait_busy_done flag cfq: Optimization for close cooperating queue searching block,xd: Delay allocation of DMA buffers until device is known drbd: Following the hmac change to SHASH (see linux commit 8bd1209c) cfq-iosched: reduce write depth only if sync was delayed
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ALSA: ac97_codec - increase timeout for analog sections to 5 second ASoC: Correct code taking the size of a pointer ALSA: hda - Add PCI IDs for Nvidia G2xx-series ALSA: sound/isa/gus: Correct code taking the size of a pointer ALSA: hda: Fix max PCM level to 0 dB for AD1981_HP ALSA: hda: Use ALC260_WILL quirk for another Acer model (0x1025007f)
-
Linus Torvalds authored
Merge branch 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits) clockevents: Convert to raw_spinlock clockevents: Make tick_device_lock static debugobjects: Convert to raw_spinlocks perf_event: Convert to raw_spinlock hrtimers: Convert to raw_spinlocks genirq: Convert irq_desc.lock to raw_spinlock smp: Convert smplocks to raw_spinlocks rtmutes: Convert rtmutex.lock to raw_spinlock sched: Convert pi_lock to raw_spinlock sched: Convert cpupri lock to raw_spinlock sched: Convert rt_runtime_lock to raw_spinlock sched: Convert rq->lock to raw_spinlock plist: Make plist debugging raw_spinlock aware bkl: Fixup core_lock fallout locking: Cleanup the name space completely locking: Further name space cleanups alpha: Fix fallout from locking changes locking: Implement new raw_spinlock locking: Convert raw_rwlock functions to arch_rwlock locking: Convert raw_rwlock to arch_rwlock ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: avr32: update default configurations for ATNGW100, ATSTK1002 and ATSTK1006 avr32: add default configurations for ATNGW100 mkII and EVKLCD10X avr32: add support for ATNGW100 mkII board avr32: convert to asm-generic/hardirq.h avr32: add two new at91 to cpu.h definition avr32: clean up linker script using standard macros. avr32: MRMT: correct setup of SPI slaves avr32: function for independently setting up SPI slaves avr32: re-instate MCI WP/CD pin assignments for ATNGW100
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc64: Fix clock event multiplier printf format. sparc64: Use clock{source,events}_calc_mult_shift(). sparc64: Use free_bootmem_late() in mdesc_lmb_free(). sparc: Add alignment and emulation fault perf events. sparc64: Add syscall tracepoint support. sparc: Stop trying to be so fancy and use __builtin_{memcpy,memset}() sparc: Use __builtin_object_size() to validate the buffer size for copy_from_user() sparc64: Add some missing __kprobes annotations to kernel fault paths. sparc64: Use kprobes_built_in() to avoid ifdefs in fault_64.c sparc: Validate that kprobe address is 4-byte aligned. sparc64: Don't specify IRQF_SHARED for LDC interrupts. sparc64: Fix stack debugging IRQ stack regression. sparc64: Fix overly strict range type matching for PCI devices.
-
git://git.infradead.org/battery-2.6Linus Torvalds authored
* git://git.infradead.org/battery-2.6: power_supply_sysfs: Handle -ENODATA in a special way wm831x_backup: Remove unused variables gta02: Set pcf50633 charger_reference_current_ma pcf50633: Query charger status directly pcf50633: Properly reenable charging when the supply conditions change pcf50633: Get rid of charging restart software auto-triggering pcf50633: introduces battery charging current control pcf50633: Add ac power supply class to the charger wm831x: Factor out WM831x backup battery charger
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: USB: Close usb_find_interface race v3 Revert "USB: Close usb_find_interface race"
-
Samu Onkalo authored
[akpm@linux-foundation.org: s/q/g/ (Randy)] Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Samu Onkalo authored
Report output values as 1/1000 of earth gravity. Output values from lis3 can be read from sysfs position entry and from input device. Input device can be accessed as event device and as joystick device. Joystick device can be in two modes. Meaning of the output values varies from case to case depending on the chip type and configuration (scale). Only joystick interface in JS_CORR_BROKEN mode returned somehow similar output values in different configurations. Joystick device is in that state by default in case of lis3. Position sysfs entry, input event device and raw joystick device have been little bit broken since meaning of the output values has been varied between 12 and 8 bit devices. Applications which relayed on those methods failed if the chip is different than the expected one. This patch converts output values to mean similar thing in different configurations. Both 8 and 12 bit devices reports now same acceleration values. If somebody implements full scale support to the driver, output values will still mean the same. Scaling factor and input device range must be updated in that case. Joystick interface in JS_CORR_BROKEN mode is not touched by this patch. All other interfaces have different scale after this change. For 12 bit device scaling factor is 0.977 which keeps scaled and unscaled values are quite close to each others. For 8 bit device, scaled values are 18 times bigger than unscaled values. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Samu Onkalo authored
It is possible to read position information at the chip measurement rate via sysfs. This patch adds possibility to configure chip measurement rate. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Signed-off-by: Éric Piel <Eric.Piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Samu Onkalo authored
Chip is calibrated by the manufacturer. There is no need to calibarate it at driver level. If the chip is used as a joystick, calibaration can be done using joystick device calibration mechanism. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Samu Onkalo authored
Implement selftest feature as specified by chip manufacturer. Control: read selftest sysfs entry Response: "OK x y z" or "FAIL x y z" where x, y, and z are difference between selftest mode and normal mode. Test is passed when values are within acceptance limit values. Acceptance limits are provided via platform data. See chip spesifications for acceptance limits. If limits are not properly set, OK / FAIL decision is meaningless. However, userspace application can still make decision based on the numeric x, y, z values. Selftest is meant for HW diagnostic purposes. It is not meant to be called during normal use of the chip. It may cause false interrupt events. Selftest mode delays polling of the normal results but it doesn't cause wrong values. Chip must be in static state during selftest. Any acceration during the test causes most probably failure. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Samu Onkalo authored
Lis3 accelerometer sensors have quite long power on delay (up to 125 ms). This patch adds necessary delay to power on sequence for currently supported lis3 chips. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Tested-by: Éric Piel <eric.piel@tremplin-utc.net> Acked-by: Éric Piel <eric.piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Éric Piel authored
Originally the driver was only targeted to 12bits sensors. When support for 8bits sensors was added, some slight difference in the registers were overlooked. This should fix it, both for initialization, and for displaying the rate. Reported-by: Kalhan Trisal <kalhan.trisal@intel.com> Reported-by: Christoph Plattner <christoph.plattner@gmx.at> Tested-by: Christoph Plattner <christoph.plattner@gmx.at> Tested-by: Samu Onkalo <samu.p.onkalo@nokia.com> Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Éric Piel authored
Most of the documentation and comments were written when the driver was only supporting one type of chip, only via ACPI/HP. Update the info to the much clearer understanding that we have now. Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Samu Onkalo authored
polled input device itself was not free'd. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Tested-by: Éric Piel <eric.piel@tremplin-utc.net> Acked-by: Éric Piel <eric.piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Samu Onkalo authored
Send input_sync after each measurement round. This helps userspace to detect which reported values belongs to the same measurement. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Tested-by: Éric Piel <eric.piel@tremplin-utc.net> Acked-by: Éric Piel <eric.piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Daniel J Blueman authored
Add control of fan minimum turn-on output levels, decoupling it from the fan turn-off output level. Add control of rate of change of fan output level. These in turn allow lower turn-off rotor speed and smoother transitions for better thermal and acoustic control authority. Add support for constant fan speed and proportional-response operations modes. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: David Hubbard <david.c.hubbard@gmail.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Samu Onkalo authored
Add the possibility to remap axes via platform data. Function pointers for resource setup and release purposes Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Éric Piel <eric.piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Cc: Jean Delvare <khali@linux-fr.org> Cc: "Trisal, Kalhan" <kalhan.trisal@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Joakim Tjernlund authored
Move common crc body to new function crc32_body() cleaup and micro optimize crc32_body for speed and less size. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Magnus Damm authored
Improve the /proc/interrupts output so the irq number can be mapped to platform device on boards with multiple tmio_mmc instances. Signed-off-by: Magnus Damm <damm@opensource.se> Cc: <linux-mmc@vger.kernel.org> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Cliff Cai authored
Add SD host driver for Blackfin BF54x and BF51x. [akpm@linux-foundation.org: fix layout, c99 warning] Signed-off-by: Cliff Cai <cliffcai.sh@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Nicolas Ferre authored
This new revision of the IP adds some improvements to the MCI already present in several Atmel SOC. Some new registers are added and a particular way of handling DMA interaction lead to a new sequence in function call which is backward compatible: On MCI2, we must set the DMAEN bit to enable the DMA handshaking interface. This must happen before the data transfer command is sent. A new function is able to differentiate MCI2 code and is based on knowledge of processor id (cpu_is_xxx()). Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Nicolas Ferre authored
Allow the use of another DMA controller driver in atmel-mci sd/mmc driver. This adds a generic dma_slave pointer to the mci platform structure where we can store DMA controller information. In atmel-mci we use information provided by this structure to initialize the driver (with new helper functions that are architecture dependant). This also adds at32/avr32 chip modifications to cope with this new access method. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Ben Hutchings authored
Some people run general-purpose distribution kernels on netbooks with a card that is physically non-removable or logically non-removable (e.g. used for /home) and cannot be cleanly unmounted during suspend. Add a module parameter to set whether cards are assumed removable or non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME. In general, it is not possible to tell whether a card present in an MMC slot after resume is the same that was there before suspend. So there are two possible behaviours, each of which will cause data loss in some cases: CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed during suspend. Any filesystem on them must be unmounted before suspend; otherwise, buffered writes will be lost. CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during suspend. They must not be swapped during suspend; otherwise, buffered writes will be flushed to the wrong card. Currently the choice is made at compile time and this allows that to be overridden at module load time. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Ben Dooks authored
Convert two missed s3c2410 specific gpio calls to gpiolib calls. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Simtec Linux Team <linux@simtec.co.uk> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Nicolas Pitre authored
This is still in use especially to develop SDIO device drivers on laptop machines which are lacking SDIO slots. This adapter supports SDIO cards only due to lack of 136-bit response capability. Signed-off-by: Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Ladislav Michl authored
Remove check for host->iclk being NULL from error path since we already know it is non-null and use return value from clk_get. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Tony Lindgren <tony@atomide.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Chaithrika U S authored
Add cpufreq support to MMC driver. The clock divider value has to be modified according to the controller input frequency. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Cc: Linus Walleij <linus.ml.walleij@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-