- 01 Apr, 2014 21 commits
-
-
Brad Volkin authored
Various commands that access memory have a bit to determine whether the graphics address specified in the command should use the GGTT or PPGTT for translation. These checks ensure that the bit indicates PPGTT translation. Most of these checks use the existing bit-checking infrastructure. The PIPE_CONTROL and MI_FLUSH_DW commands, however, are multi-function commands. The GGTT/PPGTT bit is only relevant for certain uses of the command. As such, this change also extends the bit-checking code to include a "condition" mask and offset. If the condition mask is non-zero then the parser only performs the bit check when the bits specified by the condition mask/offset are also non-zero. NOTE: At this point in the series PPGTT must be enabled for the parser to work correctly. If it's not enabled, userspace will not be setting the PPGTT bits the way the parser requires. VLV is the only platform where this is a problem, so at this point, we disable parsing for VLV. v2: whitespace and trailing commas fixes, rebased OTC-Tracker: AXIA-4631 Change-Id: I3f4c76b6734f1956ec47e698230f97d0998ff92b Signed-off-by:
Brad Volkin <bradley.d.volkin@intel.com> Reviewed-by:
Jani Nikula <jani.nikula@intel.com> [danvet: Drop the unecessary cast Jani spotted.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Brad Volkin authored
The driver leaves most interrupts masked during normal operation, so there would have to be additional work to enable userspace to safely request/receive an interrupt. v2: trailing commas, rebased Signed-off-by:
-
Brad Volkin authored
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM, and MI_LOAD_REGISTER_IMM commands allow userspace access to registers. Only certain registers should be allowed for such access, so enable checking for those commands. Each ring gets its own register whitelist. MI_LOAD_REGISTER_REG on HSW also allows register access but is currently unused by userspace components. Leave it rejected. PIPE_CONTROL and MEDIA_VFE_STATE allow register access based on certain bits being set. Reject those as well. v2: trailing commas, rebased OTC-Tracker: AXIA-4631 Change-Id: Ie614a2f0eb2e5917de809e5a17957175d24cc44f Signed-off-by:
-
Brad Volkin authored
These are used to implement scanline waits in the X server. v2: Use #defines instead of magic numbers Signed-off-by:
-
Brad Volkin authored
These registers are currently used by mesa for blitting, transform feedback extensions, and performance monitoring extensions. v2: REG64 macro Signed-off-by:
-
Brad Volkin authored
The Intel DDX uses these to implement scanline waits in the X server. Signed-off-by:
-
Brad Volkin authored
The spec defines most of these commands as privileged. A few others, like the semaphore mbox command and some display commands, are also reserved for the driver's use. Subsequent patches relax some of these restrictions. v2: Rebased Signed-off-by:
-
Brad Volkin authored
Add command tables defining irregular length commands for each ring. This requires a few new command opcode definitions. v2: Whitespace adjustment in command definitions, sparse fix for !F OTC-Tracker: AXIA-4631 Change-Id: I064bceb457e15f46928058352afe76d918c58ef5 Signed-off-by:
-
Ben Widawsky authored
When PPGTT was disabled by default, the patch also prevented the user from overriding this behavior via module parameter. Being able to test this on arbitrary kernels is extremely beneficial to track down the remaining bugs. The patch that prevented this was: commit 93a25a9e Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Thu Mar 6 09:40:43 2014 +0100 drm/i915: Disable full ppgtt by default By default PPGTT is set to -1. 0 means off, 1 means aliasing only, 2 means full, all other values are reserved. Signed-off-by:
Ben Widawsky <ben@bwidawsk.net> Signed-off-by:
-
Ben Widawsky authored
This file contains all necessary defines, prototypes and typesdefs for manipulating GEN graphics address translation (this does not include the legacy AGP driver) Reiterating the comment in the header, "Please try to maintain the following order within this file unless it makes sense to do otherwise. From top to bottom: 1. typedefs 2. #defines, and macros 3. structure definitions 4. function prototypes Within each section, please try to order by generation in ascending order, from top to bottom (ie. GEN6 on the top, GEN8 on the bottom)." I've made some minor cleanups, and fixed a couple of typos while here - but there should be no functional changes. The purpose of the patch is to reduce clutter in our main header file, making room for new growth, and make documentation of our interfaces easier by splitting things out. With a little more work, like making i915_gtt a pointer, we could potentially completely isolate this header from i915_drv.h. At the moment however, I don't think it's worth the effort. Personally, I would have liked to put the PTE encoding functions in this file too, but I didn't want to rock the boat too much. A similar patch has been in use on my machine for some time. This exact patch though has only been compile tested. Signed-off-by:
-
Daniel Vetter authored
Extract all this logic into a new helper function semaphore_wait_to_signaller_ring because: - The current code has way too much magic. - The current code doesn't look at bi16, which encodes VECS signallers on HSW. Those are just added after the fact, so can't be encoded in a neat formula. - The current logic can't blow up since it limits its value range sufficiently, but that's a bit too tricky to rely on in my opinion. Especially when we start to add bdw support. - I'm not a big fan of the explicit ring->semaphore_register list, but I think it's more robust to use the same mapping both when constructing the semaphore commands and when decoding them. - Finally add a FIXME comment about lack of broadwell support here, like in the earlier ipehr semaphore cmd detection function. Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Mika Kuoppala <mika.kuoppala@intel.com> [danvet: Actually drop the untrue claim in the commit message Chris pointed out.] Signed-off-by:
-
Daniel Vetter authored
Currently not an issue since we don't emit sempahores, but better not forget about those. As a little prep work extract the ipehr decoding for cleaner control flow. And apply a bit of polish. Cc: Ben Widawsky <ben@bwidawsk.net> Reviewed-by:
-
Chris Wilson authored
The documentation calls this GFX_MODE bit "Flush TLB invalidate Mode". However, that is not a good name for an enable bit as it doesn't make it clear what is enabled. An even worse name is GFX_TLB_INVALIDATE_ALWAYS as enabling that bit actually prevents the TLB from being invalidated at every flush. This leads to great confusion when reading code and proposed patches. To get around this try to bake in what is enabled by setting the bit and call it GFX_TLB_INVALIDATE_EXPLICIT. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: "Gupta, Sourab" <sourab.gupta@intel.com> Acked-by:
"Gupta, Sourab" <sourab.gupta@intel.com> Signed-off-by:
-
Paulo Zanoni authored
Because gen6_gt_force_wake_{get,put} should already be responsible for getting/putting runtime PM. If we keep these calls, debugfs will not be testing the get/put calls of the forcewake functions. Signed-off-by:Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
-
Paulo Zanoni authored
If runtime PM is enabled and we unset all modes, we will runtime suspend after __intel_set_mode() , then function intel_modeset_check_state() will try to read the HW state while it is suspended and trigger lots of WARNs because it shouldn't be reading registers. So on this patch we make intel_ddi_connector_get_hw_state() return false in case the power domain is disabled, and we also make intel_display_power_enabled() return false in case the device is suspended. Notice that we can't just use intel_display_power_enabled_sw() because while the driver is being initialized the power domain refcounts are not reflecting the real state of the hardware. Just for reference, I have previously published an alternate patch for this problem, called "drm/i915: get runtime PM at intel_set_mode". Testcase: igt/pm_pc8 Signed-off-by:
-
Paulo Zanoni authored
At i915_display_info, don't call cursor_position() for a disabled CRTC, since the CRTC may be on a powered down pipe, and this will cause "Unclaimed register before interrupt" error messages. Testcase: igt/pm_pc8/debugfs-read Signed-off-by:
-
Paulo Zanoni authored
Otherwise we may get some WARNs complaining that we're reading a register while we're suspended. Testcase: igt/pm_pc8/debugfs-read Signed-off-by:
-
Paulo Zanoni authored
... at edp_have_panel_vdd. Just return false, saying we don't have the panel VDD since the device is suspended. We started getting WARNs about this problem since the patch that started checking if we're suspended while reading registers. Example backtrace provided by Paulo: [ 63.572201] [drm:hsw_enable_pc8] Enabling package C8+ [ 63.581831] [drm:i915_runtime_suspend] Device suspended [ 63.664798] ------------[ cut here ]------------ [ 63.664824] WARNING: CPU: 3 PID: 828 at drivers/gpu/drm/i915/intel_uncore.c:47 assert_device_not_suspended.isra.7+0x32/0x40 [i915]() [ 63.664826] Device suspended [ 63.664828] Modules linked in: ccm fuse ip6table_filter ip6_tables ebtable_nat ebtables arc4 ath9k_htc ath9k_common ath9k_hw mac80211 ath cfg80211 iTCO_wdt iTCO_vendor_support x86_pkg_temp_thermal coretemp microcode i2c_i801 e1000e pcspkr serio_raw lpc_ich ptp pps_core mei_me mei mfd_core dm_crypt i915 crc32_pclmul crc32c_intel ghash_clmulni_intel i2c_algo_bit drm_kms_helper drm video [ 63.664867] CPU: 3 PID: 828 Comm: kworker/3:3 Not tainted 3.14.0+ #153 [ 63.664869] Hardware name: Intel Corporation Shark Bay Client platform/WhiteTip Mountain 1, BIOS HSWLPTU1.86C.0133.R00.1309172123 09/17/2013 [ 63.664887] Workqueue: events edp_panel_vdd_work [i915] [ 63.664889] 0000000000000009 ffff88009d745c28 ffffffff8167ec6f ffff88009d745c70 [ 63.664895] ffff88009d745c60 ffffffff8106c8ed ffff880036278000 00000000000c7204 [ 63.664900] ffff88014f2d3040 ffff880036278070 0000000000000001 ffff88009d745cc0 [ 63.664905] Call Trace: [ 63.664911] [<ffffffff8167ec6f>] dump_stack+0x4d/0x66 [ 63.664916] [<ffffffff8106c8ed>] warn_slowpath_common+0x7d/0xa0 [ 63.664920] [<ffffffff8106c95c>] warn_slowpath_fmt+0x4c/0x50 [ 63.664926] [<ffffffff810bd6be>] ? mark_held_locks+0xae/0x130 [ 63.664941] [<ffffffffa00d80d2>] assert_device_not_suspended.isra.7+0x32/0x40 [i915] [ 63.664956] [<ffffffffa00d99d2>] gen6_read32+0x32/0x120 [i915] [ 63.664969] [<ffffffffa00d99a0>] ? gen6_read8+0x120/0x120 [i915] [ 63.664985] [<ffffffffa0106f8f>] edp_have_panel_vdd+0x3f/0x50 [i915] [ 63.665000] [<ffffffffa01074e8>] edp_panel_vdd_off_sync+0x58/0x1c0 [i915] [ 63.665004] [<ffffffff8108a06c>] ? process_one_work+0x18c/0x560 [ 63.665018] [<ffffffffa0107684>] edp_panel_vdd_work+0x34/0x50 [i915] [ 63.665022] [<ffffffff8108a0d7>] process_one_work+0x1f7/0x560 [ 63.665026] [<ffffffff8108a06c>] ? process_one_work+0x18c/0x560 [ 63.665031] [<ffffffff8108ae2b>] worker_thread+0x11b/0x3a0 [ 63.665035] [<ffffffff8108ad10>] ? manage_workers.isra.21+0x2a0/0x2a0 [ 63.665039] [<ffffffff810916fc>] kthread+0xfc/0x120 [ 63.665043] [<ffffffff81091600>] ? kthread_create_on_node+0x230/0x230 [ 63.665048] [<ffffffff8169082c>] ret_from_fork+0x7c/0xb0 [ 63.665052] [<ffffffff81091600>] ? kthread_create_on_node+0x230/0x230 [ 63.665054] ---[ end trace 1250bcc890af9999 ]--- [ 63.665060] [drm:edp_panel_vdd_off_sync] Turning eDP VDD off [ 63.665061] ------------[ cut here ]------------ Testcase: igt/pm_pc8 Signed-off-by:
-
Paulo Zanoni authored
To avoid WARNs when we call it. Testcase: igt/pm_pc8/reg-read-ioctl Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75693Signed-off-by:
-
Paulo Zanoni authored
So far force_wake_timer was only used by gen6_gt_force_wake_put. Since we always had balanced gen6_gt_force_wake_get/put calls, we could guarantee balanced calls to intel_runtime_pm_get/put. Commit 8232644c, "drm/i915: Convert the forcewake worker into a timer func" started scheduling the force_wake_timer at gen6_read, which resulted in an unbalanced runtime_pm refcount. So this commit just reverts to the old behavior until we can find a proper way to used delayed force_wake from the register read/write macros without leaving the runtime_pm refcounts unbalanced and without runtime suspending the driver while forcewake is active. Testcase: igt/pm_pc8/rte Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76544Signed-off-by:
-
Imre Deak authored
Atm we reserve/allocate and free the power context during GT power enable/disable time. There is no need to do this, we can reserve/allocate the buffer once during driver loading and free it during driver cleanup. The re-reservation can also fail in case the driver previously manages to allocate something on the given fixed address. The buffer isn't exepected to move even if allocated by the BIOS, for safety add an assert to check this assumption. This also fixed a bug for Ville, where re-reserving the context failed during a GPU reset (I assume because something else got allocated on its fixed address). Tested-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
-
- 31 Mar, 2014 19 commits
-
-
Jani Nikula authored
Remove the rest of the references to drm_i915_private_t. No functional changes. Signed-off-by:
-
Jani Nikula authored
No functional changes. Signed-off-by:
-
Jani Nikula authored
No functional changes. Signed-off-by:
-
Jani Nikula authored
No functional changes. Signed-off-by:
-
Jani Nikula authored
Also drop any unnecessary casts. No functional changes. Signed-off-by:
-
Jani Nikula authored
No functional changes. Signed-off-by:
-
Jani Nikula authored
Also drop any unnecessary casts. No functional changes. Signed-off-by:
-
Jani Nikula authored
No functional changes. Signed-off-by:
-
Chris Wilson authored
The speculation is that we can conserve more power by masking off the interrupts at source (PMINTRMSK) rather than filtering them by the up/down thresholds (RPINTLIM). We can select which events we know will be active based on the current frequency versus our imposed range, i.e. if at minimum, we know we will not want to generate any more down-interrupts and vice versa. v2: We only need the TIMEOUT when above min frequency. v3: Tweak VLV at the same time Signed-off-by:
Deepak S <deepak.s@linux.intel.com> Signed-off-by:
-
Chris Wilson authored
What used to be a short-circuit now needs to adjust interrupt masking in response to user requests for changing the min/max allowed frequencies. This is currently done by a special case and early return, but the next patch adds another common action to take, so refactor the code to reduce duplication. Signed-off-by:
-
Chris Wilson authored
This reverts commit 27544369. Conflicts: drivers/gpu/drm/i915/i915_irq.c The partial application of interrupt masking without regard to other pathways for adjusting the RPS frequency results in completely disabling the PM interrupts. This leads to excessive power consumption as the GPU is kept at max clocks (until the failsafe mechanism fires of explicitly downclocking the GPU when all requests are idle). Or equally as bad for the UX, the GPU is kept at minimum clocks and prevented from upclocking in response to a requirement for more power. Testcase: pm_rps/blocking Cc: Deepak S <deepak.s@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Ville Syrjälä authored
If vsyncshift comes out as negative, add one htotal to it to get the corresponding positive value. This is rather theoretical as it would require a mode where the hsync+back porch is very long and the active+front porch very short. Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
Ville Syrjälä authored
PIPECONF_INTERLACE_W_FIELD_INDICATION is only meant to be used for sdvo since it implies a slightly weird vsync shift of htotal/2. For everything else we should use PIPECONF_INTERLACE_W_SYNC_SHIFT and let the value in the VSYNCSHIFT register take effect. The only exception is gen3 simply because VSYNCSHIFT didn't exist yet. Gen2 doesn't support interlaced modes at all, so we can drop the explicit gen2 checks. Signed-off-by:
-
Ville Syrjälä authored
When interlaced sdvo output is used, vsyncshift should supposedly be (htotal-1)/2. In reality PIPECONF/TRANSCONF will override it by using the legacy vsyncshift interlace mode which causes the hardware to ignore the VSYNCSHIFT register. The only odd thing here is that on PCH platforms we program the VSYNCSHIFT on both CPU and PCH, and it's not entirely clear if both sides have to agree on the value or not. On the CPU side there's no way to override the value via PIPECONF anymore, so if we want to make the CPU side agree with the PCH side, we should probably program the approriate value into VSYNCSHIFT manually. So let's do that, but for now leave the PCH side to still use the legacy interlace mode in TRANSCONF. We can also drop the gen2 check since gen2 doesn't support interlaced modes at all. Signed-off-by:
-
Jesse Barnes authored
This makes HDMI testers happier on VLV platforms. It may be that we need it for any non-SVO platform, but I don't have any tests to back that up, so I'm leaving other pre-ILK platforms alone for now. Tested-by: "Clint Taylor <clinton.a.taylor@intel.com>" Signed-off-by:
-
Daniel Vetter authored
We want future generations to at least attempt to use all features, so restrict the stolen memory disabling when vt-d is enabled to the latest generation we have reports for. Which is a HSW per the original report. Also once we get a bit a hold of some of the mysterious framebuffer in stolen memory issues that still haunt bugzilla, we should probably drop this hack again and see what happens. This was introduced in commit 0f4706d2 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Tue Mar 18 14:50:50 2014 +0200 drm/i915: Disable stolen memory when DMAR is active Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jani Nikula <jani.nikula@intel.com> Cc: David Woodhouse <dwmw2@infradead.org> References: https://bugs.freedesktop.org/show_bug.cgi?id=68535Acked-by:
-
Daniel Vetter authored
Linux 3.14 The vt-d w/a merged late in 3.14-rc needs a bit of fine-tuning, hence backmerge. Conflicts: drivers/gpu/drm/i915/i915_gem_gtt.c drivers/gpu/drm/i915/intel_ddi.c drivers/gpu/drm/i915/intel_dp.c All trivial adjacent lines changed type conflicts, so trivial git doesn't even show them in the merg commit. Signed-off-by: -
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull vfs fixes from Al Viro: "Switch mnt_hash to hlist, turning the races between __lookup_mnt() and hash modifications into false negatives from __lookup_mnt() (instead of hangs)" On the false negatives from __lookup_mnt(): "The *only* thing we care about is not getting stuck in __lookup_mnt(). If it misses an entry because something in front of it just got moved around, etc, we are fine. We'll notice that mount_lock mismatch and that'll be it" * 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: switch mnt_hash to hlist don't bother with propagate_mnt() unless the target is shared keep shadowed vfsmounts together resizable namespace.c hashes
-
