- 15 Jun, 2021 28 commits
-
-
Tudor Ambarus authored
Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml requires an "rtc" clock name. drivers/net/wireless/microchip/wilc1000/sdio.c is using "rtc" clock name as well. Comply with the binding in wilc1000/spi.c too. Fixes: 854d66df ("staging: wilc1000: look for rtc_clk clock in spi mode") Signed-off-by:
Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210428025445.81953-1-tudor.ambarus@microchip.com
-
zuoqilin authored
It is not necessary to define the variable ret to receive the return value of the get_bssid() method. Signed-off-by:
zuoqilin <zuoqilin@yulong.com> Signed-off-by:
-
Hui Tang authored
There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.c' | xargs sed -r -i 's/^[ ]+\t/\t/' $ find . -name '*.h' | xargs sed -r -i 's/^[ ]+\t/\t/' Cc: Tony Lindgren <tony@atomide.com> Signed-off-by:
Hui Tang <tanghui20@huawei.com> Signed-off-by:
-
Hui Tang authored
There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.c' | xargs sed -r -i 's/^[ ]+\t/\t/' $ find . -name '*.h' | xargs sed -r -i 's/^[ ]+\t/\t/' Cc: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by:
-
Hui Tang authored
There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.c' | xargs sed -r -i 's/^[ ]+\t/\t/' $ find . -name '*.h' | xargs sed -r -i 's/^[ ]+\t/\t/' Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com> Signed-off-by:
-
Yang Shen authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/ti/wlcore/cmd.c:824: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst drivers/net/wireless/ti/wlcore/cmd.c:853: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst drivers/net/wireless/ti/wlcore/cmd.c:882: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst Signed-off-by:
Yang Shen <shenyang39@huawei.com> Signed-off-by:
-
Yang Shen authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/rsi/rsi_91x_mgmt.c:1550: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst Cc: Amitkumar Karwar <amitkarwar@gmail.com> Cc: Siva Rebbagondla <siva8118@gmail.com> Signed-off-by:
-
Yang Shen authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:124: warning: expecting prototype for writeLLT(). Prototype was for rtl92c_llt_write() instead drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:154: warning: expecting prototype for rtl92c_init_LLT_table(). Prototype was for rtl92c_init_llt_table() instead Cc: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Yang Shen authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/marvell/libertas_tf/if_usb.c:56: warning: expecting prototype for if_usb_wrike_bulk_callback(). Prototype was for if_usb_write_bulk_callback() instead Signed-off-by:
-
Shaokun Zhang authored
Function 'brcms_c_stf_phy_txant_upd' are declared twice, remove the repeated declaration. Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by:
-
Christophe JAILLET authored
If 'brcms_attach()' fails, we must undo the previous 'ieee80211_alloc_hw()' as already done in the remove function. Fixes: 5b435de0 ("net: wireless: add brcm80211 drivers") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
Guenter Roeck authored
The parameter passed to ai_detach() is guaranteed to never be NULL because it is checked by the caller. Consequently, the result of container_of() on it is also never NULL, and a NULL check on it is unnecessary. Even without that, the NULL check would still be unnecessary because the subsequent kfree() can handle NULL arguments. On top of all that, it is misleading to check the result of container_of() against NULL because the position of the contained element could change, which would make the check invalid. Remove it. This change was made automatically with the following Coccinelle script. @@ type t; identifier v; statement s; @@ <+... ( t v = container_of(...); | v = container_of(...); ) ... when != v - if (\( !v \| v == NULL \) ) s ...+> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Íñigo Huguet authored
A static analyzer identified as a potential bug the copy of 12 bytes from a 6 bytes array to a 6 bytes array. Both arrays are 6 bytes addresses. Although not being a real bug, it is not immediately clear why is done this way: next 6 bytes address, contiguous to the first one, must also be copied to next contiguous 6 bytes address of the destination. Copying each one separately will make both static analyzers and reviewers happier. Signed-off-by:
Íñigo Huguet <ihuguet@redhat.com> Signed-off-by:
-
Matthias Brugger authored
Cypress Wi-Fi chipsets include information regarding regulatory constraints. These are provided to the driver through "Country Local Matrix" (CLM) blobs. Files present in Linux firmware repository are on a generic world-wide safe version with conservative power settings which is designed to comply with regulatory but may not provide best performance on all boards. Never the less, a better functionality can be expected with the file present, so add it to the modinfo of the driver. Signed-off-by:
Matthias Brugger <mbrugger@suse.com> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Matthias Brugger authored
BRCMF_FW_DEFAULT_PATH already defines the brcm folder, delete the second folder to match with Linux firmware repository layout. Fixes: 75729e11 ("brcmfmac: expose firmware config files through modinfo") Signed-off-by:
-
Tong Tiangen authored
brcmf_sdiod_remove has been called inside brcmf_sdiod_probe when fails, so there's no need to call another one. Otherwise, sdiodev->freezer would be double freed. Fixes: 7836102a ("brcmfmac: reset SDIO bus on a firmware crash") Signed-off-by:
Tong Tiangen <tongtiangen@huawei.com> Reviewed-by:
-
Yang Shen authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2040: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1295: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst Cc: Franky Lin <franky.lin@broadcom.com> Cc: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by:
-
Alvin Šipraga authored
The rx_lastpkt_rssi field provided by the firmware is suitable for NL80211_STA_INFO_{SIGNAL,CHAIN_SIGNAL}, while the rssi field is an average. Fix up the assignments and set the correct STA_INFO bits. This lets userspace know that the average RSSI is part of the station info. Fixes: cae355dc ("brcmfmac: Add RSSI information to get_station.") Signed-off-by:Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by:
-
Alvin Šipraga authored
The sinfo->chains field is a bitmask for filled values in chain_signal and chain_signal_avg, not a count. Treat it as such so that the driver can properly report per-chain RSSI information. Before (MIMO mode): $ iw dev wlan0 station dump ... signal: -51 [-51] dBm After (MIMO mode): $ iw dev wlan0 station dump ... signal: -53 [-53, -54] dBm Fixes: cae355dc ("brcmfmac: Add RSSI information to get_station.") Signed-off-by: -
Shawn Guo authored
Instead of aborting country code setup in firmware, use ISO3166 country code and 0 rev as fallback, when country_codes mapping table is not configured. This fallback saves the country_codes table setup for recent brcmfmac chipsets/firmwares, which just use ISO3166 code and require no revision number. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Zhen Lei authored
Use DEVICE_ATTR_ADMIN_RW() helper macro instead of DEVICE_ATTR(), making it simpler and easier to read. Because the read and write function names of the sysfs attribute have been normalized, there is a natural association. Signed-off-by:
Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by:
-
Tian Tao authored
The return value of ssb_bus_unregister can only be 0 or -1, so this condition if (err == -EBUSY) will not hold, so delete it. Signed-off-by:
Tian Tao <tiantao6@hisilicon.com> Acked-by:
Michael Büsch <m@bues.ch> Signed-off-by:
-
Michael Büsch authored
It doesn't make sense to clobber the const driver-side buffer, if a write-to-device attempt failed. All other SSB variants (PCI, PCMCIA and SoC) also don't corrupt the buffer on any failure in block_write. Therefore, remove this memset from the SDIO variant. Signed-off-by:
-
Zhen Lei authored
Fix to return -EINVAL from the error handling case instead of 0, as done elsewhere in this function. Fixes: 61e115a5 ("[SSB]: add Sonics Silicon Backplane bus support") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
-
Yang Li authored
Variable 'err' is set to zero but this value is never read as it is overwritten with a new value later on, hence it is a redundant assignment and can be removed. Clean up the following clang-analyzer warning: drivers/ssb/main.c:1306:3: warning: Value stored to 'err' is never read [clang-analyzer-deadcode.DeadStores] drivers/ssb/main.c:1312:3: warning: Value stored to 'err' is never read [clang-analyzer-deadcode.DeadStores] Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Acked-by:
-
Shubhankar Kuranagatti authored
Shifted the closing */ to the next line This is done to maintain code uniformity. Acked-by:
Shubhankar Kuranagatti <shubhankarvk@gmail.com> Signed-off-by:
-
Shubhankar Kuranagatti authored
Shifted the closing */ to the next line This is done to maintain code uniformity. Acked-by:
-
Shubhankar Kuranagatti authored
The closing */ has been shifted to a new line This is done to maintain code uniformity. Acked-by:
-
- 14 Jun, 2021 6 commits
-
-
Russell King authored
When reading the fw_log structure from the device's memory, we could race with the firmware updating the actual_buff_size and buff_write_ptr members of this structure. This would lead to bytes being dropped from the log. Fix this by writing back the actual - now fixed - clear_ptr which reflects where we read up to in the buffer. This also means that we must not check that the clear_ptr matches the current write pointer, so remove that check. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Russell King authored
With logging enabled, it has been observed that the driver spews messages such as: wlcore: ERROR Calculate of clear addr Clear = 204025b0, write = 204015b0 The problem occurs because 204025b0 is the end of the buffer, and 204015b0 is the beginning, and the calculation for "clear"ing the buffer does not take into account that if we read to the very end of the ring buffer, we are actually at the beginning of the buffer. Fix this. Signed-off-by:
-
Russell King authored
Make some of the fwlog calculations more obvious by calculating bits that get used and documenting what they are. Validate the read pointer while we're at it to ensure we do not overflow the data block we have allocated and read. Signed-off-by:
-
Russell King authored
Tidy up the use of fw_log.actual_buff_size - rather than reading it multiple times and applying the endian conversion, read it once into actual_len and use that instead. Signed-off-by:
-
Tony Lindgren authored
At least on wl12xx, reading the MAC after boot can fail with a warning at drivers/net/wireless/ti/wlcore/sdio.c:78 wl12xx_sdio_raw_read. The failed call comes from wl12xx_get_mac() that wlcore_nvs_cb() calls after request_firmware_work_func(). After the error, no wireless interface is created. Reloading the wl12xx module makes the interface work. Turns out the wlan controller can be in a low-power ELP state after the boot from the bootloader or kexec, and needs to be woken up first. Let's wake the hardware and add a sleep after that similar to wl12xx_pre_boot() is already doing. Note that a similar issue could exist for wl18xx, but I have not seen it so far. And a search for wl18xx_get_mac and wl12xx_sdio_raw_read did not produce similar errors. Cc: Carl Philipp Klemm <philipp@uvos.xyz> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
YueHaibing authored
Use DEVICE_ATTR_<RW|RO> helper instead of plain DEVICE_ATTR, which makes the code a bit shorter and easier to read. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
- 03 Jun, 2021 4 commits
-
-
Souptick Joarder authored
Kernel test robot throws below warning -> drivers/net/wireless/intel/ipw2x00/ipw2100.c:5359: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst Minor update in documentation. Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Souptick Joarder <jrdr.linux@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
Colin Ian King authored
There is a spelling mistake in a comment. Fix it. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
YueHaibing authored
commit 5d07a3d6 ("b43legacy: Avoid packet losses in the dma worker code") left behind this. Signed-off-by:
-
Zhen Lei authored
These TODO empty code are added by commit 9442e5b5 ("b43: N-PHY: partly implement SPUR workaround"). It's been more than a decade now. I don't think anyone who wants to perfect this workaround can follow this TODO tip exactly. Instead, it limits them to new thinking. Remove it will be better. No functional change. By the way, this helps reduce some binary code size. Before: text data bss dec hex 74472 9967 0 84439 149d7 After: text data bss dec hex 74408 9919 0 84327 14967 Signed-off-by:
-
- 31 May, 2021 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.14. Major changes: ath9k * provide STBC info in the received frames
-
- 30 May, 2021 1 commit
-
-
Philipp Borgers authored
The rx descriptor contains a STBC indicator. If the indicator is set the frame was received with STBC. Signed-off-by:
Philipp Borgers <borgers@mi.fu-berlin.de> Signed-off-by:
-
