The device ID for VFs is in a different location than PFs. This results
in the poll always timing out for VFs. There's no good way to read the
VF device ID without using the PF's configuration space.  Switch to waiting
for the health poll to start incrementing. Also remove the 1s sleep
at the beginning.

fixes: 89d44f0a ('net/mlx5_core: Add pci error handlers to mlx5_core
driver')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change page cleanup flow when in internal error to properly decrement
the page counts when reclaiming pages.  The prevents timing out waiting
for extra pages that were actually cleaned up previously.

fixes: 89d44f0a ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In internal error state the health poll thread will eventually call
synchronize_irq() (to safely trigger command completions) which might
sleep, so we are calling sleeping function from atomic context which is
invalid.
Here we move trigger_cmd_completions(dev) to enter error state which is
the earliest stage in error state handling.
This way we won't need to wait for next health poll to trigger command
completions and will solve the scheduling while atomic issue.
mlx5_enter_error_state can be called from two contexts, protect it with
dev->intf_state_lock

Fixes: 89d44f0a ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of internal error state we will simulate the commands status
through the return value translation function, but we need to simulate
all the teardown fw commands as successful so we will not have fw
command failure prints.
This also fix memory leaks that happen because we skip teardown stages
due to failed fw commands.

Fixes: 89d44f0a ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ether_addr_equal_64bits() requires some care about its arguments,
namely that 8 bytes might be read, even if last 2 byte values are not
used.

KASan detected a violation with null_mac_addr and lacpdu_mcast_addr
in bond_3ad.c

Same problem with mac_bcast[] and mac_v6_allmcast[] in bond_alb.c :
Although the 8-byte alignment was there, KASan would detect out
of bound accesses.

Fixes: 815117ad ("bonding: use ether_addr_equal_unaligned for bond addr compare")
Fixes: bb54e589 ("bonding: Verify RX LACPDU has proper dest mac-addr")
Fixes: 885a136c ("bonding: use compare_ether_addr_64bits() in ALB")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If mvneta_mdio_probe() fails, a kernel warning is triggered due to
missing cleanup in the error path.  Add the necessary cleanup.

------------[ cut here ]------------
WARNING: CPU: 1 PID: 281 at kernel/irq/manage.c:1814 __free_percpu_irq+0xfc/0x130
percpu IRQ 38 still enabled on CPU0!
Modules linked in: bnep bluetooth xhci_plat_hcd xhci_hcd marvell_cesa armada_thermal des_generic ehci_orion mcp3021 spi_orion sfp mdio_i2c evbug fuse
CPU: 1 PID: 281 Comm: connmand Not tainted 4.7.0-rc2+ #53
Hardware name: Marvell Armada 380/385 (Device Tree)
Backtrace:
[<c0013488>] (dump_backtrace) from [<c00137d0>] (show_stack+0x18/0x1c)
 r6:60010093 r5:ffffffff r4:00000000 r3:dc8ba500
[<c00137b8>] (show_stack) from [<c02c6fe0>] (dump_stack+0xa4/0xdc)
[<c02c6f3c>] (dump_stack) from [<c002d4ec>] (__warn+0xd8/0x104)
 r6:c081e6a0 r5:00000000 r4:edfe5d50 r3:dc8ba500
[<c002d414>] (__warn) from [<c002d5d0>] (warn_slowpath_fmt+0x40/0x48)
 r10:a0010013 r8:c09356f8 r7:00000026 r6:ef11a260 r5:edd7b980 r4:ef11a200
[<c002d594>] (warn_slowpath_fmt) from [<c008c8e0>] (__free_percpu_irq+0xfc/0x130)
 r3:00000026 r2:c081e7ac
[<c008c7e4>] (__free_percpu_irq) from [<c008c95c>] (free_percpu_irq+0x48/0x74)
 r10:00008914 r8:00000000 r7:ffffffed r6:c09356f8 r5:00000026 r4:ef11a200
[<c008c914>] (free_percpu_irq) from [<c043dd70>] (mvneta_open+0x118/0x134)
 r6:ffffffed r5:ef01e640 r4:ef01e000 r3:ef01e000
[<c043dc58>] (mvneta_open) from [<c055f5b4>] (__dev_open+0xa4/0x108)
 r7:ef01e030 r6:c06ff3d8 r5:ffff9003 r4:ef01e000
[<c055f510>] (__dev_open) from [<c055f844>] (__dev_change_flags+0x94/0x150)
 r7:00001002 r6:00000001 r5:ffff9003 r4:ef01e000
[<c055f7b0>] (__dev_change_flags) from [<c055f938>] (dev_change_flags+0x20/0x50)
 r8:00000000 r7:c09334c8 r6:00001002 r5:00000148 r4:ef01e000 r3:00008914
[<c055f918>] (dev_change_flags) from [<c05de044>] (devinet_ioctl+0x6f4/0x7e0)
 r8:00000000 r7:c09334c8 r6:00000000 r5:ee87200c r4:00000000 r3:00008914
[<c05dd950>] (devinet_ioctl) from [<c05e0168>] (inet_ioctl+0x1b8/0x1c8)
 r10:beb4499c r9:edfe4000 r8:ecf13280 r7:c096cf00 r6:beb4499c r5:eef7c240
 r4:00008914
[<c05dffb0>] (inet_ioctl) from [<c053c898>] (sock_ioctl+0x78/0x300)
[<c053c820>] (sock_ioctl) from [<c0155ecc>] (do_vfs_ioctl+0x98/0xa60)
 r7:00000011 r6:00008914 r5:00000011 r4:c01568d0
[<c0155e34>] (do_vfs_ioctl) from [<c01568d0>] (SyS_ioctl+0x3c/0x60)
 r10:00000000 r9:edfe4000 r8:beb4499c r7:00000011 r6:00008914 r5:ecf13280
 r4:ecf13280
[<c0156894>] (SyS_ioctl) from [<c000fe60>] (ret_fast_syscall+0x0/0x1c)
 r8:c0010004 r7:00000036 r6:00000011 r5:000a2978 r4:00000000 r3:00009003
---[ end trace 711f625d5b04b3a7 ]---
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LINK_OFF_WAKE_EN should be cleared after autoresume, otherwise after
system suspend, the system would wake up when linking off occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call wmb() to ensure writes are complete before
hardware fetches updated Tx descriptors.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When MTU is changed unlink_urbs() flushes RX Q but mean while usbnet_bh()
can fill up the Q at the same time.
Depends on which HCD is down there unlink takes long time then the flush
never ends.
Signed-off-by: Soohoon Lee <soohoon.lee@f5.com>
Reviewed-by: Kimball Murray <kmurray@f5.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_skb_dst_mtu uses skb->sk, assuming it is an AF_INET socket (e.g. it
calls ip_sk_use_pmtu which casts sk as an inet_sk).

However, in the case of UDP tunneling, the skb->sk is not necessarily an
inet socket (could be AF_PACKET socket, or AF_UNSPEC if arriving from
tun/tap).

OTOH, the sk passed as an argument throughout IP stack's output path is
the one which is of PMTU interest:
 - In case of local sockets, sk is same as skb->sk;
 - In case of a udp tunnel, sk is the tunneling socket.

Fix, by passing ip_finish_output's sk to ip_skb_dst_mtu.
This augments 7026b1dd 'netfilter: Pass socket pointer down through okfn().'
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2016-06-29

This series contains fixes to e1000e and ixgbevf.

Jarod Wilson's fix for e1000e was a follow-on patch to his previous fix to
keep the hardware VLAN CTAG's for receive and transmit in sync, which
in turn resolves the original issue, so revert a portion of the original
fix.

Xin Long noticed that the ret_val needed to be initialized to IXGBE_ERR_MBX,
instead of -IXGBE_ERR_MBX.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull NFS client bugfixes from Anna Schumaker:
 "Stable bugfixes:
   - Fix _cancel_empty_pagelist
   - Fix a double page unlock
   - Make nfs_atomic_open() call d_drop() on all ->open_context() errors.
   - Fix another OPEN_DOWNGRADE bug

  Other bugfixes:
   - Ensure we handle delegation errors in nfs4_proc_layoutget()
   - Layout stateids start out as being invalid
   - Add sparse lock annotations for pnfs_find_alloc_layout
   - Handle bad delegation stateids in nfs4_layoutget_handle_exception
   - Fix up O_DIRECT results
   - Fix potential use after free of state in nfs4_do_reclaim.
   - Mark the layout stateid invalid when all segments are removed
   - Don't let readdirplus revalidate an inode that was marked as stale
   - Fix potential race in nfs_fhget()
   - Fix an unused variable warning"

* tag 'nfs-for-4.7-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFS: Fix another OPEN_DOWNGRADE bug
  make nfs_atomic_open() call d_drop() on all ->open_context() errors.
  NFS: Fix an unused variable warning
  NFS: Fix potential race in nfs_fhget()
  NFS: Don't let readdirplus revalidate an inode that was marked as stale
  NFSv4.1/pnfs: Mark the layout stateid invalid when all segments are removed
  NFS: Fix a double page unlock
  pnfs_nfs: fix _cancel_empty_pagelist
  nfs4: Fix potential use after free of state in nfs4_do_reclaim.
  NFS: Fix up O_DIRECT results
  NFS/pnfs: handle bad delegation stateids in nfs4_layoutget_handle_exception
  NFSv4.1/pnfs: Add sparse lock annotations for pnfs_find_alloc_layout
  NFSv4.1/pnfs: Layout stateids start out as being invalid
  NFSv4.1/pnfs: Ensure we handle delegation errors in nfs4_proc_layoutget()

Pull audit fixes from Paul Moore:
 "Two small patches to fix audit problems in 4.7-rcX: the first fixes a
  potential kref leak, the second removes some header file noise.

  The first is an important bug fix that really should go in before 4.7
  is released, the second is not critical, but falls into the very-nice-
  to-have category so I'm including in the pull request.

  Both patches are straightforward, self-contained, and pass our
  testsuite without problem"

* 'stable-4.7' of git://git.infradead.org/users/pcmoore/audit:
  audit: move audit_get_tty to reduce scope and kabi changes
  audit: move calcs after alloc and check when logging set loginuid

Pull networking fixes from David Miller:
 "I've been traveling so this accumulates more than week or so of bug
  fixing.  It perhaps looks a little worse than it really is.

   1) Fix deadlock in ath10k driver, from Ben Greear.

   2) Increase scan timeout in iwlwifi, from Luca Coelho.

   3) Unbreak STP by properly reinjecting STP packets back into the
      stack.  Regression fix from Ido Schimmel.

   4) Mediatek driver fixes (missing malloc failure checks, leaking of
      scratch memory, wrong indexing when mapping TX buffers, etc.) from
      John Crispin.

   5) Fix endianness bug in icmpv6_err() handler, from Hannes Frederic
      Sowa.

   6) Fix hashing of flows in UDP in the ruseport case, from Xuemin Su.

   7) Fix netlink notifications in ovs for tunnels, delete link messages
      are never emitted because of how the device registry state is
      handled.  From Nicolas Dichtel.

   8) Conntrack module leaks kmemcache on unload, from Florian Westphal.

   9) Prevent endless jump loops in nft rules, from Liping Zhang and
      Pablo Neira Ayuso.

  10) Not early enough spinlock initialization in mlx4, from Eric
      Dumazet.

  11) Bind refcount leak in act_ipt, from Cong WANG.

  12) Missing RCU locking in HTB scheduler, from Florian Westphal.

  13) Several small MACSEC bug fixes from Sabrina Dubroca (missing RCU
      barrier, using heap for SG and IV, and erroneous use of async flag
      when allocating AEAD conext.)

  14) RCU handling fix in TIPC, from Ying Xue.

  15) Pass correct protocol down into ipv4_{update_pmtu,redirect}() in
      SIT driver, from Simon Horman.

  16) Socket timer deadlock fix in TIPC from Jon Paul Maloy.

  17) Fix potential deadlock in team enslave, from Ido Schimmel.

  18) Memory leak in KCM procfs handling, from Jiri Slaby.

  19) ESN generation fix in ipv4 ESP, from Herbert Xu.

  20) Fix GFP_KERNEL allocations with locks held in act_ife, from Cong
      WANG.

  21) Use after free in netem, from Eric Dumazet.

  22) Uninitialized last assert time in multicast router code, from Tom
      Goff.

  23) Skip raw sockets in sock_diag destruction broadcast, from Willem
      de Bruijn.

  24) Fix link status reporting in thunderx, from Sunil Goutham.

  25) Limit resegmentation of retransmit queue so that we do not
      retransmit too large GSO frames.  From Eric Dumazet.

  26) Delay bpf program release after grace period, from Daniel
      Borkmann"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (141 commits)
  openvswitch: fix conntrack netlink event delivery
  qed: Protect the doorbell BAR with the write barriers.
  neigh: Explicitly declare RCU-bh read side critical section in neigh_xmit()
  e1000e: keep VLAN interfaces functional after rxvlan off
  cfg80211: fix proto in ieee80211_data_to_8023 for frames without LLC header
  qlcnic: use the correct ring in qlcnic_83xx_process_rcv_ring_diag()
  bpf, perf: delay release of BPF prog after grace period
  net: bridge: fix vlan stats continue counter
  tcp: do not send too big packets at retransmit time
  ibmvnic: fix to use list_for_each_safe() when delete items
  net: thunderx: Fix TL4 configuration for secondary Qsets
  net: thunderx: Fix link status reporting
  net/mlx5e: Reorganize ethtool statistics
  net/mlx5e: Fix number of PFC counters reported to ethtool
  net/mlx5e: Prevent adding the same vxlan port
  net/mlx5e: Check for BlueFlame capability before allocating SQ uar
  net/mlx5e: Change enum to better reflect usage
  net/mlx5: Add ConnectX-5 PCIe 4.0 to list of supported devices
  net/mlx5: Update command strings
  net: marvell: Add separate config ANEG function for Marvell 88E1111
  ...

Pull s390 fixes from Martin Schwidefsky:
 "Another two bug fixes for 4.7:

   - The revert of patch which removed boot information for systems
     using an intermediate boot kernel, e.g. the SLES12 grub setup.

   - A fix for an incorrect inline assembly constraint that causes
     broken code to be generated with gcc 4.8.5"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: fix test_fp_ctl inline assembly contraints
  Revert "s390/kdump: Clear subchannel ID to signal non-CCW/SCSI IPL"

Pull pin control fixes from Linus Walleij:
 "Here are a bunch of fixes for pin control.  Just drivers and a
  MAINTAINERS fixup:

   - Driver fixes for i.MX, single register, Tegra and BayTrail.

   - MAINTAINERS entry for the documentation"

* tag 'pinctrl-v4.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: baytrail: Fix mingled clock pins
  MAINTAINERS: belong Documentation/pinctrl.txt properly
  pinctrl: tegra: Fix build dependency
  gpio: tegra: Make lockdep class file-scoped
  pinctrl: single: Fix missing flush of posted write for a wakeirq
  pinctrl: imx: Do not treat a PIN without MUX register as an error

Pull cgroup fixes from Tejun Heo:
 "Three fix patches.  Two are for cgroup / css init failure path.  The
  last one makes css_set_lock irq-safe as the deadline scheduler ends up
  calling put_css_set() from irq context"

* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: Disable IRQs while holding css_set_lock
  cgroup: set css->id to -1 during init
  cgroup: remove redundant cleanup in css_create

Now ixgbevf_write/read_posted_mbx use -IXGBE_ERR_MBX as the initiative
return value, but it's incorrect, cause in ixgbevf_vlan_rx_add_vid(),
it use err == IXGBE_ERR_MBX, the err returned from mac.ops.set_vfta,
and in ixgbevf_set_vfta_vf, it return from write/read_posted. so we
should initialize err with IXGBE_ERR_MBX, instead of -IXGBE_ERR_MBX.

With this fix, the other functions that called it also can work well,
cause they only care about if err is 0 or not.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The bit in the e1000 driver that mentions explicitly that the hardware
has no support for separate RX/TX VLAN accel toggling rings true for
e1000e as well, and thus both NETIF_F_HW_VLAN_CTAG_RX and
NETIF_F_HW_VLAN_CTAG_TX need to be kept in sync.

Revert a portion of commit 889ad456 ("e1000e: keep VLAN interfaces
functional after rxvlan off") since keeping the bits in sync resolves
the original issue.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge tag 'mac80211-for-davem-2016-06-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just two small fixes
 * fix mesh peer link counter, decrement wasn't always done at all
 * fix ethertype (length) for packets without RFC 1042 or bridge
   tunnel header
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Only the first and last netlink message for a particular conntrack are
actually sent. The first message is sent through nf_conntrack_confirm when
the conntrack is committed. The last one is sent when the conntrack is
destroyed on timeout. The other conntrack state change messages are not
advertised.

When the conntrack subsystem is used from netfilter, nf_conntrack_confirm
is called for each packet, from the postrouting hook, which in turn calls
nf_ct_deliver_cached_events to send the state change netlink messages.

This commit fixes the problem by calling nf_ct_deliver_cached_events in the
non-commit case as well.

Fixes: 7f8a436e ("openvswitch: Add conntrack action")
CC: Joe Stringer <joestringer@nicira.com>
CC: Justin Pettit <jpettit@nicira.com>
CC: Andy Zhou <azhou@nicira.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Samuel Gauthier <samuel.gauthier@6wind.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

SPQ doorbell is currently protected with the compilation barrier. Under the
stress scenarios, we may get into a state where (due to the weak ordering)
several ramrod doorbells were written to the BAR with an out-of-order
producer values. Need to change the barrier type to a write barrier to make
sure that the write buffer is flushed after each doorbell.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh_xmit() expects to be called inside an RCU-bh read side critical
section, and while one of its two current callers gets this right, the
other one doesn't.

More specifically, neigh_xmit() has two callers, mpls_forward() and
mpls_output(), and while both callers call neigh_xmit() under
rcu_read_lock(), this provides sufficient protection for neigh_xmit()
only in the case of mpls_forward(), as that is always called from
softirq context and therefore doesn't need explicit BH protection,
while mpls_output() can be called from process context with softirqs
enabled.

When mpls_output() is called from process context, with softirqs
enabled, we can be preempted by a softirq at any time, and RCU-bh
considers the completion of a softirq as signaling the end of any
pending read-side critical sections, so if we do get a softirq
while we are in the part of neigh_xmit() that expects to be run inside
an RCU-bh read side critical section, we can end up with an unexpected
RCU grace period running right in the middle of that critical section,
making things go boom.

This patch fixes this impedance mismatch in the callee, by making
neigh_xmit() always take rcu_read_{,un}lock_bh() around the code that
expects to be treated as an RCU-bh read side critical section, as this
seems a safer option than fixing it in the callers.

Fixes: 4fd3d7d9 ("neigh: Add helper function neigh_xmit")
Signed-off-by: David Barroso <dbarroso@fastly.com>
Signed-off-by: Lennert Buytenhek <lbuytenhek@fastly.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I've got a bug report about an e1000e interface, where a VLAN interface is
set up on top of it:

$ ip link add link ens1f0 name ens1f0.99 type vlan id 99
$ ip link set ens1f0 up
$ ip link set ens1f0.99 up
$ ip addr add 192.168.99.92 dev ens1f0.99

At this point, I can ping another host on vlan 99, ip 192.168.99.91.
However, if I do the following:

$ ethtool -K ens1f0 rxvlan off

Then no traffic passes on ens1f0.99. It comes back if I toggle rxvlan on
again. I'm not sure if this is actually intended behavior, or if there's a
lack of software VLAN stripping fallback, or what, but things continue to
work if I simply don't call e1000e_vlan_strip_disable() if there are
active VLANs (plagiarizing a function from the e1000 driver here) on the
interface.

Also slipped a related-ish fix to the kerneldoc text for
e1000e_vlan_strip_disable here...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.

The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.

Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.

Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.

Fixes: 2d1c304c ("cfg80211: add function for 802.3 conversion with separate output buffer")
Cc: stable@vger.kernel.org
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>

There is a static checker warning here "warn: mask and shift to zero"
and the code sets "ring" to zero every time.  From looking at how
QLCNIC_FETCH_RING_ID() is used in qlcnic_83xx_process_rcv_ring() the
qlcnic_83xx_hndl() should be removed.

Fixes: 4be41e92 ('qlcnic: 83xx data path routines')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit dead9f29 ("perf: Fix race in BPF program unregister") moved
destruction of BPF program from free_event_rcu() callback to __free_event(),
which is problematic if used with tail calls: if prog A is attached as
trace event directly, but at the same time present in a tail call map used
by another trace event program elsewhere, then we need to delay destruction
via RCU grace period since it can still be in use by the program doing the
tail call (the prog first needs to be dropped from the tail call map, then
trace event with prog A attached destroyed, so we get immediate destruction).

Fixes: dead9f29 ("perf: Fix race in BPF program unregister")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Jann Horn <jann@thejh.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

I made a dumb off-by-one mistake when I added the vlan stats counter
dumping code. The increment should happen before the check, not after
otherwise we miss one entry when we continue dumping.

Fixes: a60c0903 ("bridge: netlink: export per-vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arjun reported a bug in TCP stack and bisected it to a recent commit.

In case where we process SACK, we can coalesce multiple skbs
into fat ones (tcp_shift_skb_data()), to lower write queue
overhead, because we do not expect to retransmit these packets.

However, SACK reneging can happen, forcing the sender to retransmit
all these packets. If skb->len is above 64KB, we then send buggy
IP packets that could hang TSO engine on cxgb4.

Neal suggested to use tcp_tso_autosize() instead of tp->gso_segs
so that we cook packets of optimal size vs TCP/pacing.

Thanks to Arjun for reporting the bug and running the tests !

Fixes: 10d3be56 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Arjun V <arjun@chelsio.com>
Tested-by: Arjun V <arjun@chelsio.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each() macro aptly named
list_for_each_safe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sunil Goutham says:

====================
net: thunderx: Miscellaneous fixes

This 2 patch series fixes issues w.r.t physical link status
reporting and transmit datapath configuration for
secondary qsets.

Changes from v1:
Fixed lmac disable sequence for interfaces of type SGMII.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

TL4 calculation for a given SQ of secondary Qsets is incorrect
and goes out of bounds and also for some SQ's TL4 chosen will
transmit data via a different BGX interface and not same as
primary Qset's interface.

This patch fixes this issue.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check for SMU RX local/remote faults along with SPU LINK
status. Otherwise at times link is UP at our end but DOWN
at link partner's side. Also due to an issue in BGX it's
rarely seen that initialization doesn't happen properly
and SMU RX reports faults with everything fine at SPU.
This patch tries to reinitialize LMAC to fix it.

Also fixed LMAC disable sequence to properly bring down link.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Tao Wang <tao.wang@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 fixes#2 for 4.7-rc

The following series provides one-liners fixes for mlx5 driver plus one
medium patch to reorganize ethtool counters reporting.

Highlights:
	- Added MODIFY_FLOW_TABLE to command strings table
	- Add ConnectX-5 PCIe 4.0 to list of supported devices
	- Rename ASYNC_EVENTS enum
	- Enable BlueFlame only when supported by device
	- Avoid adding same vxlan port twice
	- Report the correct number of PFC counters
	- Reorganize ethtool reported counters and remove duplications
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Categorize and reorganize ethtool statistics counters by renaming to
"rx_*" and "tx_*" and removing redundant and duplicated counters, this
way they are easier to grasp and more user friendly.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Number of PFC counters used to count only number of priorities with PFC
enabled, but each priority has more than one counter, hence the need to
multiply it by the number of PFC counters per priority.

Fixes: cf678570 ('net/mlx5e: Add per priority group to PPort counters')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not allow the same vxlan udp port to be added to the device more than
once.

Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous to this patch mapping was always set to write combining without
checking whether BlueFlame is supported in the device.

Fixes: 0ba42241 ('net/mlx5: Fix global UAR mapping')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change MLX5E_STATE_ASYNC_EVENTS_ENABLE to
MLX5E_STATE_ASYNC_EVENTS_ENABLED since it represent a state and not an
operation.

Fixes: acff797c ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the upcoming ConnectX-5 PCIe 4.0 device to the list of
supported devices by the mlx5 driver.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>