- 06 Aug, 2014 4 commits
-
-
Axel Lin authored
On platforms with sizeof(int) < sizeof(long), writing a temperature limit larger than MAXINT will result in unpredictable limit values written to the chip. Avoid auto-conversion from long to int to fix the problem. Voltage limits, fan minimum speed, pwm frequency, pwm ramp rate, and other attributes have the same problem, fix them as well. Zone temperature limits are signed, but were cached as u8, causing unepected values to be reported for negative temperatures. Cache as s8 to fix the problem. vrm is an u8, so the written value needs to be limited to [0, 255]. Signed-off-by: Axel Lin <axel.lin@ingics.com> [Guenter Roeck: Fix zone temperature cache] Cc: stable@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
-
Guenter Roeck authored
Temperature limit range is [-127, 127], not [-127, 128]. The wrong range caused a bad limit to be written into the chip if the limit was set to a value of 128 degrees C or above. Also use DIV_ROUND_CLOSEST instead of a plain divide operation to reduce the rounding error when writing temperature limits. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Jean Delvare <jdelvare@suse.de>
-
Axel Lin authored
Current code uses data_rate as array index in ads1015_read_adc() and uses pga as array index in ads1015_reg_to_mv, so we must make sure both data_rate and pga settings are in valid value range. Return -EINVAL if the setting is out-of-range. Signed-off-by: Axel Lin <axel.lin@ingics.com> Cc: stable@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
-
Axel Lin authored
On platforms with sizeof(int) < sizeof(long), writing a temperature limit larger than MAXINT will result in unpredictable limit values written to the chip. Avoid auto-conversion from long to int to fix the problem. The hysteresis temperature range depends on the value of data->temp[attr->index], since val is subtracted from it. Use a wider clamp, [-120000, 220000] should do to cover the possible range. Also add missing TEMP_TO_REG() on writes into cached hysteresis value. Also uses clamp_val to simplify the code a bit. Signed-off-by: Axel Lin <axel.lin@ingics.com> [Guenter Roeck: Fixed double TEMP_TO_REG on hysteresis updates] Cc: stable@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
-
- 05 Aug, 2014 36 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-mediaLinus Torvalds authored
Pull media updates from Mauro Carvalho Chehab: - removal of sn9c102. This device driver was replaced a long time ago by gspca - solo6x10 and go7007 webcam drivers moved from staging into mainstream. They were waiting for an API to allow setting the image detection matrix - SDR drivers moved from staging into mainstream: sdr-msi3101 (renamed as msi2500) and rtl2832 - added SDR driver for airspy - added demux driver: si2165 - rework at several RC subsystem, making the code for RC-5 SZ variant to be added at the standard RC5 decoder - added decoder for the XMP IR protocol - tuner driver moved from staging into mainstream: msi3101 (renamed as msi001) - added documentation for some additional SDR pixfmt - some device tree bindings documented - added support for exynos3250 at s5p-jpeg - remove the obsolete, unmaintained and broken mx1_camera driver - added support for remote controllers at au0828 driver - added a RC driver: sunxi-cir - several driver fixes, enhancements and cleanups. * 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (455 commits) [media] cx23885: fix UNSET/TUNER_ABSENT confusion [media] coda: fix build error by making reset control optional [media] radio-miropcm20: fix sparse NULL pointer warning [media] MAINTAINERS: Update go7007 pattern [media] MAINTAINERS: Update solo6x10 patterns [media] media: atmel-isi: add primary DT support [media] media: atmel-isi: convert the pdata from pointer to structure [media] media: atmel-isi: add v4l2 async probe support [media] rcar_vin: add devicetree support [media] media: pxa_camera device-tree support [media] media: mt9m111: add device-tree suppport [media] soc_camera: add support for dt binding soc_camera drivers [media] media: soc_camera: pxa_camera documentation device-tree support [media] media: mt9m111: add device-tree documentation [media] s5p-mfc: remove unnecessary calling to function video_devdata() [media] s5p-jpeg: add chroma subsampling adjustment for Exynos3250 [media] s5p-jpeg: Prevent erroneous downscaling for Exynos3250 SoC [media] s5p-jpeg: Assure proper crop rectangle initialization [media] s5p-jpeg: fix g_selection op [media] s5p-jpeg: Adjust jpeg_bound_align_image to Exynos3250 needs ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulatorLinus Torvalds authored
Pull regulator updates from Mark Brown: "A couple of nice new features this month, the ability to map regulators in order to allow voltage control by external coprocessors is something people have been asking for for a long time. - improved support for switch only "regulators", allowing current state to be read from the parent regulator but no setting. - support for obtaining the register access method used to set voltages, for use in systems which can offload control of this to a coprocessor (typically for DVFS). - support for Active-Semi AC8846, Dialog DA9211 and Texas Instruments TPS65917" * tag 'regulator-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (58 commits) regulator: act8865: fix build when OF is not enabled regulator: act8865: add act8846 to DT binding documentation regulator: act8865: add support for act8846 regulator: act8865: prepare support for other act88xx devices regulator: act8865: set correct number of regulators in pdata regulator: act8865: Remove error variable in act8865_pmic_probe regulator: act8865: fix parsing of platform data regulator: tps65090: Set voltage for fixed regulators regulator: core: Allow to get voltage count and list from parent regulator: core: Get voltage from parent if not available regulator: Add missing statics and inlines for stub functions regulator: lp872x: Don't set constraints within the regulator driver regmap: Fix return code for stub regmap_get_device() regulator: s2mps11: Update module description and Kconfig to add S2MPU02 support regulator: Add helpers for low-level register access regmap: Allow regmap_get_device() to be used by modules regmap: Add regmap_get_device regulator: da9211: Remove unnecessary devm_regulator_unregister() calls regulator: Add DT bindings for tps65218 PMIC regulators. regulator: da9211: new regulator driver ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spiLinus Torvalds authored
Pull spi updates from Mark Brown: "A quiet release, more bug fixes than anything else. A few things do stand out though: - updates to several drivers to move towards the standard GPIO chip select handling in the core. - DMA support for the SH MSIOF driver. - support for Rockchip SPI controllers (their first mainline submission)" * tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits) spi: davinci: use spi_device.cs_gpio to store gpio cs per spi device spi: davinci: add support to configure gpio cs through dt spi/pl022: Explicitly truncate large bitmask spi/atmel: Fix pointer to int conversion warnings on 64 bit builds spi: davinci: fix to support more than 2 chip selects spi: topcliff-pch: don't hardcode PCI slot to get DMA device spi: orion: fix incorrect handling of cell-index DT property spi: orion: Fix error return code in orion_spi_probe() spi/rockchip: fix error return code in rockchip_spi_probe() spi/rockchip: remove redundant dev_err call in rockchip_spi_probe() spi/rockchip: remove duplicated include from spi-rockchip.c ARM: dts: fix the chip select gpios definition in the SPI nodes spi: s3c64xx: Update binding documentation spi: s3c64xx: use the generic SPI "cs-gpios" property spi: s3c64xx: Revert "spi: s3c64xx: Added provision for dedicated cs pin" spi: atmel: Use dmaengine_prep_slave_sg() API spi: topcliff-pch: Update error messages for dmaengine_prep_slave_sg() API spi: sh-msiof: Use correct device for DMA mapping with IOMMU spi: sh-msiof: Handle dmaengine_prep_slave_single() failures gracefully spi: rspi: Handle dmaengine_prep_slave_sg() failures gracefully ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommuLinus Torvalds authored
Pull iommu updates from Joerg Roedel: "This time with: - support for the generic PCI device alias code in x86 IOMMU drivers - a new sysfs interface for IOMMUs - preparations for hotplug support in the Intel IOMMU driver - change the AMD IOMMUv2 driver to not hold references to core data structures like mm_struct or task_struct. Rely on mmu_notifers instead. - removal of the OMAP IOVMM interface, all users of it are converted to DMA-API now - make the struct iommu_ops const everywhere - initial PCI support for the ARM SMMU driver - there is now a generic device tree binding documented for ARM IOMMUs - various fixes and cleanups all over the place Also included are some changes to the OMAP code, which are acked by the maintainer" * tag 'iommu-updates-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (67 commits) devicetree: Add generic IOMMU device tree bindings iommu/vt-d: Fix race setting IRQ CPU affinity while freeing IRQ iommu/amd: Fix 2 typos in comments iommu/amd: Fix device_state reference counting iommu/amd: Remove change_pte mmu_notifier call-back iommu/amd: Don't set pasid_state->mm to NULL in unbind_pasid iommu/exynos: Select ARM_DMA_USE_IOMMU iommu/vt-d: Exclude devices using RMRRs from IOMMU API domains iommu/omap: Remove platform data da_start and da_end fields ARM: omap: Don't set iommu pdata da_start and da_end fields iommu/omap: Remove virtual memory manager iommu/vt-d: Fix issue in computing domain's iommu_snooping flag iommu/vt-d: Introduce helper function iova_size() to improve code readability iommu/vt-d: Introduce helper domain_pfn_within_range() to simplify code iommu/vt-d: Simplify intel_unmap_sg() and kill duplicated code iommu/vt-d: Change iommu_enable/disable_translation to return void iommu/vt-d: Simplify include/linux/dmar.h iommu/vt-d: Avoid freeing virtual machine domain in free_dmar_iommu() iommu/vt-d: Fix possible invalid memory access caused by free_dmar_iommu() iommu/vt-d: Allocate dynamic domain id for virtual domains only ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-stagingLinus Torvalds authored
Pull hwmon updates from Guenter Roeck: "Notable changes: - Heiko Schocher provided a driver for TI TMP103. - Kamil Debski provided a driver for pwm-controlled fans. - Neelesh Gupta provided a driver for power, fan rpm, voltage and temperature reporting on powerpc/powernv systems. - Scott Kanowitz provided a driver supporting Lattice's POWR1220 power manager IC. - Richard Zhu provided a pmbus front-end driver for TPS40422. - Frans Klaver added support for TMP112 to the lm75 driver. - Johannes Pointner added support for EPCOS B57330V2103 to the ntc_thermistor driver. - Guenter Roeck added support for TMP441 and TMP442 to the tmp421 driver. - Axel Lin converted several drivers to the new hwmon API (36 of them, if I counted correctly), and cleaned up many of the drivers along the way. There are also a number of patches fixing bugs discovered while testing Axel's changes" * tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (88 commits) hwmon: (g762) Use of_property_read_u32 at appropriate place hwmon: (sis5595) Prevent overflow problem when writing large limits hwmon: (gpio-fan) Prevent overflow problem when writing large limits hwmon: (ibmpowernv) Use of_property_read_u32 at appropriate place hwmon: (lm85) Convert to devm_hwmon_device_register_with_groups hwmon: (lm85) Avoid forward declaration hwmon: (lm78) Convert to devm_hwmon_device_register_with_groups hwmon: (max6697) Use of_property_read_bool at appropriate places hwmon: (pwm-fan) Make SENSORS_PWM_FAN depend on OF hwmon: (pwm-fan) Remove duplicate dev_set_drvdata call hwmon: (nct6775) Remove num_attr_groups from struct nct6775_data hwmon: (nct6775) Update module description and Kconfig for NCT6106D and NCT6791D hwmon: (adt7411) Convert to devm_hwmon_device_register_with_groups hwmon: (g762) Convert to hwmon_device_register_with_groups hwmon: (emc2103) Convert to devm_hwmon_device_register_with_groups hwmon: (smsc47m1) Avoid forward declaration hwmon: (smsc47m192) Convert to devm_hwmon_device_register_with_groups hwmon: (smsc47m192) Avoid forward declaration hwmon: (max1668) Make max1668_addr_list array const hwmon: (max6639) Make normal_i2c array const ...
-
Mark Brown authored
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regulator-next
-
Mark Brown authored
Merge remote-tracking branches 'regulator/topic/tps65217', 'regulator/topic/tps65218', 'regulator/topic/tps6586x' and 'regulator/topic/twl' into regulator-next
-
Mark Brown authored
Merge remote-tracking branches 'regulator/topic/s2mps11', 'regulator/topic/s2mpu02', 'regulator/topic/s5m8767' and 'regulator/topic/tps65090' into regulator-next
-
Mark Brown authored
Merge remote-tracking branches 'regulator/topic/lp8755', 'regulator/topic/ltc3589', 'regulator/topic/max8952', 'regulator/topic/mc13xxx' and 'regulator/topic/palmas' into regulator-next
-
Mark Brown authored
Merge remote-tracking branches 'regulator/topic/da9211', 'regulator/topic/getreg', 'regulator/topic/gpio' and 'regulator/topic/lp872x' into regulator-next
-
Mark Brown authored
Merge remote-tracking branches 'regulator/topic/88pm800', 'regulator/topic/ab8500', 'regulator/topic/act8865', 'regulator/topic/as3722' and 'regulator/topic/bcm590xx' into regulator-next
-
Mark Brown authored
-
Mark Brown authored
Merge remote-tracking branches 'regulator/fix/act8865', 'regulator/fix/arizona' and 'regulator/fix/tps65218' into regulator-linus
-
Mark Brown authored
Conflicts: drivers/regulator/act8865-regulator.c
-
git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM updates from Russell King: "Included in this update: - perf updates from Will Deacon: The main changes are callchain stability fixes from Jean Pihet and event mapping and PMU name rework from Mark Rutland The latter is preparatory work for enabling some code re-use with arm64 in the future. - updates for nommu from Uwe Kleine-König: Two different fixes for the same problem making some ARM nommu configurations not boot since 3.6-rc1. The problem is that user_addr_max returned the biggest available RAM address which makes some copy_from_user variants fail to read from XIP memory. - deprecate legacy OMAP DMA API, in preparation for it's removal. The popular drivers have been converted over, leaving a very small number of rarely used drivers, which hopefully can be converted during the next cycle with a bit more visibility (and hopefully people popping out of the woodwork to help test) - more tweaks for BE systems, particularly with the kernel image format. In connection with this, I've cleaned up the way we generate the linker script for the decompressor. - removal of hard-coded assumptions of the kernel stack size, making everywhere depend on the value of THREAD_SIZE_ORDER. - MCPM updates from Nicolas Pitre. - Make it easier for proper CPU part number checks (which should always include the vendor field). - Assembly code optimisation - use the "bx" instruction when returning from a function on ARMv6+ rather than "mov pc, reg". - Save the last kernel misaligned fault location and report it via the procfs alignment file. - Clean up the way we create the initial stack frame, which is a repeated pattern in several different locations. - Support for 8-byte get_user(), needed for some DRM implementations. - mcs locking from Will Deacon. - Save and restore a few more Cortex-A9 registers (for errata workarounds) - Fix various aspects of the SWP emulation, and the ELF hwcap for the SWP instruction. - Update LPAE logic for pte_write and pmd_write to make it more correct. - Support for Broadcom Brahma15 CPU cores. - ARM assembly crypto updates from Ard Biesheuvel" * 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (53 commits) ARM: add comments to the early page table remap code ARM: 8122/1: smp_scu: enable SCU standby support ARM: 8121/1: smp_scu: use macro for SCU enable bit ARM: 8120/1: crypto: sha512: add ARM NEON implementation ARM: 8119/1: crypto: sha1: add ARM NEON implementation ARM: 8118/1: crypto: sha1/make use of common SHA-1 structures ARM: 8113/1: remove remaining definitions of PLAT_PHYS_OFFSET from <mach/memory.h> ARM: 8111/1: Enable erratum 798181 for Broadcom Brahma-B15 ARM: 8110/1: do CPU-specific init for Broadcom Brahma15 cores ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE ARM: 8108/1: mm: Introduce {pte,pmd}_isset and {pte,pmd}_isclear ARM: hwcap: disable HWCAP_SWP if the CPU advertises it has exclusives ARM: SWP emulation: only initialise on ARMv7 CPUs ARM: SWP emulation: always enable when SMP is enabled ARM: 8103/1: save/restore Cortex-A9 CP15 registers on suspend/resume ARM: 8098/1: mcs lock: implement wfe-based polling for MCS locking ARM: 8091/2: add get_user() support for 8 byte types ARM: 8097/1: unistd.h: relocate comments back to place ARM: 8096/1: Describe required sort order for textofs-y (TEXT_OFFSET) ARM: 8090/1: add revision info for PL310 errata 588369 and 727915 ...
-
Beniamino Galvani authored
act8846_matches and act8865_matches are defined only when OF is enabled. Move references to them to the act8865_pdata_from_dt() function to avoid a build error when OF is disabled. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
-
Beniamino Galvani authored
This patch adds a new "active-semi,act8846" compatible string and a list of supported regulator names to the devicetree binding documentation for Active-Semi PMUs. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
-
Beniamino Galvani authored
Add device id and definition of registers and regulators to support the act8846 PMU. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Tested-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
-
Beniamino Galvani authored
This patch prepares support for other devices in the act88xx family of PMUs manufactured by Active-Semi. http://www.active-semi.com/products/power-management-units/act88xx/Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Tested-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
-
Beniamino Galvani authored
act8865_pdata_from_dt() populates the array pdata->regulators with all the regulators and then assigns the field init_data only for the ones actually found in the DT. The patch changes the value assigned to pdata->num_regulators to match the size of the array. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Tested-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
-
Axel Lin authored
Simply use ret variable instead. Also remove unneeded initialize for ret variable. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
-
Beniamino Galvani authored
The driver loops through all available regulators (ACT8865_REG_NUM) and accesses pdata->regulators[i].platform_data without checking the actual value of num_regulators in platform data, potentially causing a invalid memory access. Fix this and look up the regulator init_data by id in platform data. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Tested-by Wenyou.Yang <wenyou.yang@atmel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommuLinus Torvalds authored
Pull m68knommu fixes from Greg Ungerer: "Just a couple of small fixes. Fix definition of page_to_phys() and remove unecesary prototype of kobjsize()" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: m68knommu: Remove unnecessary prototype for kobjsize() m68knommu: Correct page_to_phys when PAGE_OFFSET is non-zero.
-
Russell King authored
Conflicts: arch/arm/kernel/perf_event_cpu.c
-
Russell King authored
-
Russell King authored
Conflicts: arch/arm/kernel/iwmmxt.S arch/arm/mm/cache-l2x0.c arch/arm/mm/mmu.c
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 updates from Ted Ts'o: "Bug fixes and clean ups for the 3.17 merge window" * tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: fix ext4_discard_allocated_blocks() if we can't allocate the pa struct ext4: fix COLLAPSE RANGE test for bigalloc file systems ext4: check inline directory before converting ext4: fix incorrect locking in move_extent_per_page ext4: use correct depth value ext4: add i_data_sem sanity check ext4: fix wrong size computation in ext4_mb_normalize_request() ext4: make ext4_has_inline_data() as a inline function ext4: remove readpage() check in ext4_mmap_file() ext4: fix punch hole on files with indirect mapping ext4: remove metadata reservation checks ext4: rearrange initialization to fix EXT4FS_DEBUG
-
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fsLinus Torvalds authored
Pull f2fs updates from Jaegeuk Kim: "This series includes patches to: - add nobarrier mount option - support tmpfile and rename2 - enhance the fdatasync behavior - fix the error path - fix the recovery routine - refactor a part of the checkpoint procedure - reduce some lock contentions" * tag 'for-f2fs-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (40 commits) f2fs: use for_each_set_bit to simplify the code f2fs: add f2fs_balance_fs for expand_inode_data f2fs: invalidate xattr node page when evict inode f2fs: avoid skipping recover_inline_xattr after recover_inline_data f2fs: add tracepoint for f2fs_direct_IO f2fs: reduce competition among node page writes f2fs: fix coding style f2fs: remove redundant lines in allocate_data_block f2fs: add tracepoint for f2fs_issue_flush f2fs: avoid retrying wrong recovery routine when error was occurred f2fs: test before set/clear bits f2fs: fix wrong condition for unlikely f2fs: enable in-place-update for fdatasync f2fs: skip unnecessary data writes during fsync f2fs: add info of appended or updated data writes f2fs: use radix_tree for ino management f2fs: add infra for ino management f2fs: punch the core function for inode management f2fs: add nobarrier mount option f2fs: fix to put root inode in error path of fill_super ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds authored
Pull USB updates from Greg KH: "Here is the big USB driver update for 3.17-rc1. Loads of gadget driver changes in here, including some big file movements to make things easier to manage over time. There's also the usual xhci and uas driver updates, and a handful of other changes in here. The changelog has the full details. All of these have been in linux-next for a while" * tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits) USB: devio: fix issue with log flooding uas: Log a warning when we cannot use uas because the hcd lacks streams uas: Only complain about missing sg if all other checks succeed xhci: Add missing checks for xhci_alloc_command failure xhci: Rename Asrock P67 pci product-id to EJ168 xhci: Blacklist using streams on the Etron EJ168 controller uas: Limit qdepth to 32 when connected over usb-2 uwb/whci: use correct structure type name in sizeof usb-core bInterval quirk USB: serial: ftdi_sio: Add support for new Xsens devices USB: serial: ftdi_sio: Annotate the current Xsens PID assignments usb: chipidea: debug: fix sparse non static symbol warnings usb: ci_hdrc_imx doc: fsl,usbphy is required usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY usb: core: allow zero packet flag for interrupt urbs usb: lvstest: Fix sparse warnings generated by kbuild test bot USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down phy: miphy365x: Represent each PHY channel as a DT subnode phy: miphy365x: Provide support for the MiPHY356x Generic PHY phy: miphy365x: Add Device Tree bindings for the MiPHY365x ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/ttyLinus Torvalds authored
Pull tty / serial driver update from Greg KH: "Here's the big tty / serial driver update for 3.17-rc1. Nothing major, just a number of fixes and new features for different serial drivers, and some more tty core fixes and documentation of the tty locks. All of these have been in linux-next for a while" * tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (82 commits) tty/n_gsm.c: fix a memory leak in gsmld_open pch_uart: don't hardcode PCI slot to get DMA device tty: n_gsm, use setup_timer Revert "ARC: [arcfpga] stdout-path now suffices for earlycon/console" serial: sc16is7xx: Correct initialization of s->clk serial: 8250_dw: Add support for deferred probing serial: 8250_dw: Add optional reset control support serial: st-asc: Fix overflow in baudrate calculation serial: st-asc: Don't call BUG in asc_console_setup() tty: serial: msm: Make of_device_id array const tty/n_gsm.c: get gsm->num after gsm_activate_mux serial/core: Fix too big allocation for attribute member drivers/tty/serial: use correct type for dma_map/unmap serial: altera_jtaguart: Fix putchar function passed to uart_console_write() serial/uart/8250: Add tunable RX interrupt trigger I/F of FIFO buffers Serial: allow port drivers to have a default attribute group tty: kgdb_nmi: Automatically manage tty enable serial: altera_jtaguart: Adpot uart_console_write() serial: samsung: improve code clarity by defining a variable serial: samsung: correct the case and default order in switch ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull staging driver updates from Greg KH: "Here's the big pull request for the staging driver tree for 3.17-rc1. Lots of things in here, over 2000 patches, but the best part is this: 1480 files changed, 39070 insertions(+), 254659 deletions(-) Thanks to the great work of Kristina Martšenko, 14 different staging drivers have been removed from the tree as they were obsolete and no one was willing to work on cleaning them up. Other than the driver removals, loads of cleanups are in here (comedi, lustre, etc.) as well as the usual IIO driver updates and additions. All of this has been in the linux-next tree for a while" * tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (2199 commits) staging: comedi: addi_apci_1564: remove diagnostic interrupt support code staging: comedi: addi_apci_1564: add subdevice to check diagnostic status staging: wlan-ng: coding style problem fix staging: wlan-ng: fixing coding style problems staging: comedi: ii_pci20kc: request and ioremap memory staging: lustre: bitwise vs logical typo staging: dgnc: Remove unneeded dgnc_trace.c and dgnc_trace.h staging: dgnc: rephrase comment staging: comedi: ni_tio: remove some dead code staging: rtl8723au: Fix static symbol sparse warning staging: rtl8723au: usb_dvobj_init(): Remove unused variable 'pdev_desc' staging: rtl8723au: Do not duplicate kernel provided USB macros staging: rtl8723au: Remove never set struct pwrctrl_priv.bHWPowerdown staging: rtl8723au: Remove two never set variables staging: rtl8723au: RSSI_test is never set staging:r8190: coding style: Fixed checkpatch reported Error staging:r8180: coding style: Fixed too long lines staging:r8180: coding style: Fixed commenting style staging: lustre: ptlrpc: lproc_ptlrpc.c - fix dereferenceing user space buffer staging: lustre: ldlm: ldlm_resource.c - fix dereferenceing user space buffer ...
-
Linus Torvalds authored
Merge tag 'driver-core-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here's the big driver-core pull request for 3.17-rc1. Largest thing in here is the dma-buf rework and fence code, that touched many different subsystems so it was agreed it should go through this tree to handle merge issues. There's also some firmware loading updates, as well as tests added, and a few other tiny changes, the changelog has the details. All have been in linux-next for a long time" * tag 'driver-core-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits) ARM: imx: Remove references to platform_bus in mxc code firmware loader: Fix _request_firmware_load() return val for fw load abort platform: Remove most references to platform_bus device test: add firmware_class loader test doc: fix minor typos in firmware_class README staging: android: Cleanup style issues Documentation: devres: Sort managed interfaces Documentation: devres: Add devm_kmalloc() et al fs: debugfs: remove trailing whitespace kernfs: kernel-doc warning fix debugfs: Fix corrupted loop in debugfs_remove_recursive stable_kernel_rules: Add pointer to netdev-FAQ for network patches driver core: platform: add device binding path 'driver_override' driver core/platform: remove unused implicit padding in platform_object firmware loader: inform direct failure when udev loader is disabled firmware: replace ALIGN(PAGE_SIZE) by PAGE_ALIGN firmware: read firmware size using i_size_read() firmware loader: allow disabling of udev as firmware loader reservation: add suppport for read-only access using rcu reservation: update api and add some helpers ... Conflicts: drivers/base/platform.c
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds authored
Pull char / misc driver patches from Greg KH: "Here's the big driver misc / char pull request for 3.17-rc1. Lots of things in here, the thunderbolt support for Apple laptops, some other new drivers, testing fixes, and other good things. All have been in linux-next for a long time" * tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (119 commits) misc: bh1780: Introduce the use of devm_kzalloc Lattice ECP3 FPGA: Correct endianness drivers/misc/ti-st: Load firmware from ti-connectivity directory. dt-bindings: extcon: Add support for SM5502 MUIC device extcon: sm5502: Change internal hardware switch according to cable type extcon: sm5502: Detect cable state after completing platform booting extcon: sm5502: Add support new SM5502 extcon device driver extcon: arizona: Get MICVDD against extcon device extcon: Remove unnecessary OOM messages misc: vexpress: Fix sparse non static symbol warnings mei: drop unused hw dependent fw status functions misc: bh1770glc: Use managed functions pcmcia: remove DEFINE_PCI_DEVICE_TABLE usage misc: remove DEFINE_PCI_DEVICE_TABLE usage ipack: Replace DEFINE_PCI_DEVICE_TABLE macro use drivers/char/dsp56k.c: drop check for negativity of unsigned parameter mei: fix return value on disconnect timeout mei: don't schedule suspend in pm idle mei: start disconnect request timer consistently mei: reset client connection state on timeout ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 vdso updates from Ingo Molnar: "Further simplifications and improvements to the VDSO code, by Andy Lutomirski" * 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86_64/vsyscall: Fix warn_bad_vsyscall log output x86/vdso: Set VM_MAYREAD for the vvar vma x86, vdso: Get rid of the fake section mechanism x86, vdso: Move the vvar area before the vdso text
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 UV TLB update from Ingo Molnar: "UV TLB shootdown logic updates for version of the UV architecture" * 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/uv: Update the UV3 TLB shootdown logic
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull RAS updates from Ingo Molnar: "The main changes in this cycle are: - RAS tracing/events infrastructure, by Gong Chen. - Various generalizations of the APEI code to make it available to non-x86 architectures, by Tomasz Nowicki" * 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/ras: Fix build warnings in <linux/aer.h> acpi, apei, ghes: Factor out ioremap virtual memory for IRQ and NMI context. acpi, apei, ghes: Make NMI error notification to be GHES architecture extension. apei, mce: Factor out APEI architecture specific MCE calls. RAS, extlog: Adjust init flow trace, eMCA: Add a knob to adjust where to save event log trace, RAS: Add eMCA trace event interface RAS, debugfs: Add debugfs interface for RAS subsystem CPER: Adjust code flow of some functions x86, MCE: Robustify mcheck_init_device trace, AER: Move trace into unified interface trace, RAS: Add basic RAS trace event x86, MCE: Kill CPU_POST_DEAD
-