Enable sta power save in fw for the targets that
supports idle power save. The idle ps enable command
will be ignored by the firmware which does not support
this feature.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

SRRI/DRRI are not mapped in the HW Shadow block and can lead
to un-clocked access if common subsystem in the target is
powered down due to idle mode.

To mitigate this problem SRRI/DRRI can be read from
DDR instead of doing an actual hardware read.
Host allocates non cached memory on ddr and configures
the physical address of this memory to the CE hardware.
The hardware updates the RRI on this particular location.
Read SRRI/DRRI from DDR location instead of
direct target read.

Enable retention restore on ddr using hw params to enable
in specific targets.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

WCN3990 needs shadow register write operation support
for copy engine for regular operation in powersave mode.
Add support for copy engine shadow register write in
datapath tx for WCN3990
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wcn3990 supports shadow register for ce write.

Add a hw param for shadow register support.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

By default ath10k driver enables the support for HW_CHECKSUM
(NETIF_F_HW_CSUM). Since the TCP/UDP checksum calculation is not enabled
in the wcn3990 firmware the checksum is incorrect in the TCP/UDP packets
and all patckets are dropped. But due note that wcn3990 support in
ath10k is still incomplete so this isn't a critical fix (yet).

Enable hw checksum calculations in wcn3990 hardware by
setting the proper flags in msdu descriptor tso flags.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The firmware message to delete BSS keys expects a BSS index to be passed.
This field is currently hard-coded to 0. Fix this by passing in the index
we received from the firmware when the BSS was configured.

The encryption type in that message also needs to be set to what was used
when the key was set, so the assignment of vif_priv->encrypt_type is now
done after the firmware command was sent. This reportedly fixes the
following error in AP mode:

  wcn36xx: ERROR hal_remove_bsskey response failed err=6

Also, AFAIU, when a BSS is deleted, the firmware apparently drops all the
keys associated with it. Trying to remove the key explicitly afterwards
will hence lead to the following message:

  wcn36xx: ERROR hal_remove_bsskey response failed err=16

This is now suppressed with an extra check for the BSS index validity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When trying to set wow wakeup patterns it fails with this command:

iw phyxx wowlan enable patterns offset xx+ IP address xx.xx.xx.xx

The reason is that the wow pattern from upper layer is in 802.3 format
for this case, it need to convert it to 802.11 format. The input
offset parameter is used for 802.3, but the actual offset firmware
need depends on rx_decap_mode, so that it needs to be recalculated.
Pattern of 802.3 packet is not same with 802.11 packet. If the
rx_decap_mode is ATH10K_HW_TXRX_NATIVE_WIFI, then firmware will
receive data packet with 802.11 format from hardware.

Tested with QCA6174 hw3.0 with firmware
WLAN.RM.4.4.1-00099-QCARMSWPZ-1, but this will also affect QCA9377.
This has always failed, so it's not a regression with new firmware
releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.

Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When accessing shared memory to check for the stat of submitted
descriptors, make sure to use READ_ONCE(). This will guarantee the
compiler treats these memory locations as volatile and doesn't apply
any caching.

While this doesn't fix any particular problem I ran into, it's best
practice to do it this way.

Note that this patch also removes the superflous extra condition check
in the do-while loop in reap_tx_dxes(), as the loop will break
instantly anyway in that case.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

FW path is mapped incorrectly for the WCN3990
hw version. Fix fw path with correct hw1.0 name.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Added for the same reason as the TX wrappers.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

These wrappers makes the HTT ops align better with the HIF ops
(where similar wrappers are used).

It also makes it easier for a target to have unsupported ops
(by letting the corresponding function pointer be NULL).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

commit f2593cb1 ("ath10k: Search SMBIOS for OEM board file
extension") added a feature to ath10k that allows Board Data File
(BDF) conflicts between multiple devices that use the same device IDs
but have different calibration requirements to be resolved by allowing
a "variant" string to be stored in SMBIOS [and later device tree, added
by commit d06f26c5 ("ath10k: search DT for qcom,ath10k-calibration-
variant")] that gets appended to the ID stored in board-2.bin.

This original patch had a regression, however. Namely that devices with
a variant present in SMBIOS that didn't need custom BDFs could no longer
find the default BDF, which has no variant appended. The patch was
reverted and re-applied with a fix for this issue in commit 1657b8f8
("search SMBIOS for OEM board file extension").

But the fix to fall back to a default BDF introduced another issue: the
driver currently parses IEs in board-2.bin one by one, and for each one
it first checks to see if it matches the ID with the variant appended.
If it doesn't, it checks to see if it matches the "fallback" ID with no
variant. If a matching BDF is found at any point during this search, the
search is terminated and that BDF is used. The issue is that it's very
possible (and is currently the case for board-2.bin files present in the
ath10k-firmware repository) for the default BDF to occur in an earlier
IE than the variant-specific BDF. In this case, the current code will
happily choose the default BDF even though a better-matching BDF is
present later in the file.

This patch fixes the issue by first searching the entire file for the ID
with variant, and searching for the fallback ID only if that search
fails. It also includes some code cleanup in the area, as
ath10k_core_fetch_board_data_api_n() no longer does its own string
mangling to remove the variant from an ID, instead leaving that job to a
new flag passed to ath10k_core_create_board_name().

I've tested this patch on a QCA4019 and verified that the driver behaves
correctly for 1) both fallback and variant BDFs present, 2) only fallback
BDF present, and 3) no matching BDFs present.

Fixes: 1657b8f8 ("ath10k: search SMBIOS for OEM board file extension")
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fix a typo in the function ath10k_wmi_set_wmm_param().
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Correct a minor bug in the commit 0628467f ("ath10k: fix
copy engine 5 destination ring stuck") which introduced a change to fix
firmware assert that happens when ring indices of copy engine 5 are stuck
for a specific duration, problem with this fix is that it did not use
ring arithmatic. As a result,firmware asserts did not go away entirely
athough the frequency of occurrence has reduced. Using ring arithmatic
to fix the issue.

Tested on QCA9984(fw version-10.4-3.4-00082).

Fixes: 0628467f ("ath10k: fix copy engine 5 destination ring stuck)
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add device tree binding documentation details for wcn3990
wifi block present in Qualcomm SDM845/APQ8098 SoC into
"qcom,ath10k.txt".
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add clock and regulator votes for WCN3990 WLAN
chipset.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

WCN3990 has interrupts per CE and the interrupt summary
is not retained after the interrupt handler has finished
execution. We need to check if we received any
ce in rx and tx completion path.

Generate a interrupt summary with all CE interrupts if
the target does not retain interrupt summary after the
execution of interrupt handler.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wcn3990 does not use bmi.
Add support to get target info from hif ops.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Change type of hif sg tx paddr to dma_addr_t for
supporting target having addressing mode greater than
32 bit.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add hif rx methods in rx path for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add hif tx/tx-complete methods for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add hif power-up/power-down methods for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add mapping of HTC endpoint services supported
by wcn3990 target to tx/rx pipe.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

WCN3990 target uses 3 Copy engine(CE1/CE9/CE10) in RX path
and CE 11 for pktlog.
Add data path HTC ep services and PKTLOG services for WCN3990.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add hif start/stop callback for allocating/freeing buffers
on tx/rx pipe and enabling/disabling the tx/rx pipe
interrupts.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add methods for resource(memory, irq, HOST CE config)
initialization and de-initialization for WCN3990 target.

WCN3990 target uses 12 copy engine and following CE config.

[CE0] :host->target control and raw streams
[CE1] :target->host HTT
[CE2] :target->host WMI
[CE3] :host->target WMI
[CE4] :host->target HTT
[CE5] :reserved
[CE6] :Target autonomous HIF_memcpy
[CE7] :reserved
[CE8] :reserved
[CE9] :target->host HTT
[CE10] :target->host HTT
[CE11] :target -> host PKTLOG
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

WCN3990 is integrated 802.11ac chipset with SNOC
bus interface. Add snoc layer driver registration
and associated ops.

WCN3990 support is not yet complete as cold-boot
handshake is done using qmi(Qualcomm-MSM-Interface)
and qmi client support will be added once qmi framework
is available.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

CE layer is shared between pci and snoc target and results
in duplicate object inclusion if both modules are compiled
together statically and undefined KBUILD_MODNAME if
compiled as module.

Fix this by building ce layer in ath10k core module by
adding ce object inclusion with ATH10K_CE boolean CONFIG.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch add support to get RSSI from acknowledgment
frames for transmitted management frames.

hardware_used: QCA4019, QCA9984.
firmware version: 10.4-3.5.3-00052.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

GFP_ATOMIC should only be used when the allocation is done from atomic
context. Introduce a new flag to wcn36xx_dxe_fill_skb() and use GFP_KERNEL
when pre-allocating buffers during init.

This doesn't fix an issue that was observed in the wild, but it reduces
the chance of failed allocations under memory pressure.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Each DXE control block is associated to a specific channel.
The channel lock is always taken before accessing a control block.
There is no need to have an extra (useless) spinlock for the control
block skb.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This prevents GCC warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The firmware code cannot cope with requests to remove BSS indices that have
not previously been added. This primarily happens when the device is
suspended and then resumed. ieee80211_reconfig() then calls into
wcn36xx_bss_info_changed() with an empty bssid and BSS_CHANGED_BSSID set,
which subsequently leads to a firmware crash:

[   43.647928] qcom-wcnss-pil a204000.wcnss: fatal error received: halMsg.c:4964:halMsg_DelBss: Invalid BSSIndex 0
[   43.647959] remoteproc remoteproc0: crash detected in a204000.wcnss: type fatal error

To fix this, set bss_index to WCN36XX_HAL_BSS_INVALID_IDX for all bss
that have not been configured in the firmware, and don't call into the
firmware with invalid indices.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When wcn36xx_dxe_tx_frame() fails to transmit the TX frame, the driver
will call into ieee80211_free_txskb() for the skb in flight, so it'll no
longer be valid. Hence, we shouldn't keep a reference to it in ctl->skb.
Also, if the skb has IEEE80211_TX_CTL_REQ_TX_STATUS set, a pointer to
it will currently remain in wcn->tx_ack_skb, which will potentially lead
to a crash if accessed later.

Fix this by checking the return value of wcn36xx_dxe_tx_frame(), and
nullify wcn->tx_ack_skb again in case of errors. Move the assignment
of ctl->skb in wcn36xx_dxe_tx_frame() so it only happens when the
transmission is successful.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Bail out if the mapping fails. Even though this hasn't occured during
tests, this unlikely case should still be handled.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation to enabling -Wvla, remove accidental use of stack VLA.

This avoids an accidental stack VLA (since the compiler thinks
the value of FFT_NUM_SAMPLES can change, even when marked
"const"). This just replaces it with a #define.

Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>